Write‐once–read‐many‐times memory (WORM) devices were fabricated using Ti/Au and Au as top contacts on ZnO thin films on Si. Electrical characterization shows that both types of WORM devices have large resistance OFF/ON ratio (R ratio), small resistance distribution range, long retention and good endurance. WORM devices with Au top contact have better performance of higher R ratio because of a larger work function of Au compared to Ti.
This Letter reports on the assembly on the tip of an optical fibre of a metamaterial film fabricated by a self‐assembly bottom‐up method, composed of silver nanowires embedded in an alumina matrix. By illuminating the film through the fibre in a reflection configuration, we observe experimentally the optical response of the metamaterial in agreement with theoretical predictions and interpreted as the excitation of surface plasmon‐polaritons in the cylindrical surface of the nanowires. These results pave the way for low‐cost optical fibre devices that incorporate metamaterial films.
We report on the photoconductance in two‐dimensional arrays of gold nanorods. The arrays are formed by a combination of droplet deposition and stamping methods. We find that the plasmon induced photoconductance is sensitive to the linear polarization of the exciting photons consistent with the excitation of the longitudinal surface plasmon resonance of the nanorods.
Electric control of magnetism is demonstrated in a multiferroic metal–organic framework with a perovskite structure. A moderate electric field of a few kV/cm applied during the cooling process is able to cause a large (more than 50%) change of the magnetization at low temperature. This significant magnetoelectric effect is ascribed to the electric field manipulation of orientation of hydrogen bonds that modify the superexchange interaction between metal ions.
Here, we demonstrate the synthesis of graphene on Ag foil by an atmospheric‐pressure (AP) chemical vapor deposition (CVD) process as tarnish‐resistant coating. Synthesis of a continuous graphene film on Ag foil is achieved using the solid camphor as carbon precursor in a gas mixture of Ar and H2. Tarnishing of the Ag surface through sulfidation is investigated with and without coating of the graphene film. It is observed that the bare Ag surface immediately reacts with sulfur vapor to turn black, whereas graphene coating passivates the Ag surface robustly and thereby restrains the sulfur reaction to preserve from tarnishing. Our findings show that a large‐area graphene film can be effectively grown on Ag surface by a CVD process as a tarnish and corrosion resistance barrier.
We have shown that nitrophenyl groups may be added to the surface of few‐layer epitaxial graphene (EG) by the formation of covalent carbon–carbon bonds thereby changing the electronic structure and transport properties of EG from near‐metallic to semiconducting. In the present Letter we discuss the opportunities afforded by such chemical processes to engineer device functionality in graphene by modification of the electronic properties without physical patterning.
We report the fabrication procedure and the characterization of an Al0.3Ga0.7As solar cell containing high‐density GaAs strain‐free quantum dots grown by droplet epitaxy. The production of photocurrent when two sub‐bandgap energy photons are absorbed simultaneously is demonstrated. The high quality of the quantum dot/barrier pair, allowed by the high quality of nanostructured strain‐free materials, opens new opportunities for quantum dot based solar cells.
Heteroepitaxial growth of III‐Sb nanowires allows for the formation of various interesting complex structures and enables the combination of their remarkable properties. In this Letter, we investigate the heteroepitaxial growth of Au‐seeded InSb and GaSb nanowires using metalorganic vapor phase epitaxy. We demonstrate successful single and double axial InSb–GaSb heterostructures in both directions. The formation properties of the grown nanowires including the compositional change of the particle and the interface sharpness are further discussed. In addition, the decomposition of InSb and GaSb segments and their side facet evolution are explained.
We present the synthesis of highly crystalline metallic rhenium trioxide (ReO3) nanowires via a simple physical vapor transport at 300 °C for the first time. Based on HRTEM, the ReO3 nanowires exhibit a core of perfect cubic perovskite‐type single crystal structure with a shell of thin amorphous and disordered structures of less than 2 nm in the near surface layers. Possibly this is due to proton intercalation induced by the surface reaction of single crystal ReO3 with water.
By means of first‐principles calculations we predict the stability of silicene as buckled honeycomb lattice on passivated substrates of group‐IV(111)1 × 1 surfaces. The weak van‐der‐Waals interaction between silicene and substrates does not destroy its linear bands forming Dirac cones at the Brillouin zone corners. Only very small fundamental gaps are opened around the Fermi level.
A facile metal catalyst free route to synthesize boron doped (0.6%–1.0%) carbon nanotubes via ceramic nanowires in which the formation of the nanowires (probably serving as templates), the carbon nanotubes and their doping all occur unanimously in the reaction, is presented.
We report on wet etching of photomodified regions in crystalline sapphire using KOH solution. Tightly focused femtosecond laser pulses (150 fs at 800 nm wavelength) were used to create void structures enclosed in an amorphised sapphire shell inside the bulk of a crystalline host. The diameter of the amorphous regions can be controlled by pulse energy and was typically 0.5–1.5 µm. The etching rate depends on the distance between adjacent irradiation spots, pulse energy, concentration of etchant and ultrasonic agitation.
In this Letter, we report on a new nanofabrication technology to yield highly arrayed nanoelectrodes for organic–inorganic solar cells that promise new levels of performance and efficiency. This technology efficiently controls the effective area of highly arrayed nanoelectrodes and allows for the maximum incorporation of organic materials within the voids. Particularly the 3D parameters such as thickness, spacing, and height of the nanostructures are controlled non‐lithographically by atomic layer deposition technology.
Epitaxial TiC/SiC multilayers were grown by magnetron sputtering at a substrate temperature of 550 °C, where SiC is normally amorphous. The epitaxial TiC template induced growth of cubic SiC up to a thickness of ～2 nm. Thicker SiC layers result in a direct transition to growth of the metastable amorphous SiC followed by renucleation of nanocrystalline TiC layers.
Steady‐state and time‐resolved photoluminescence of silicon nanoparticles dispersed in low‐polar liquids at above room temperature is studied. The roles of low‐polar liquids as well as mechanisms responsible for their temperature‐dependent photoluminescence are discussed. The thermal sensitivity of the photoluminescence is estimated and application of the nanoparticles as nanothermometers is proposed.
The fabrication of titania nanostructures with hierarchical order of different structural levels is investigated. The nanostructures are prepared with a diblock‐copolymer assisted sol–gel process. By iterative spin‐coating of the solution onto silicon substrates a thin polymer‐nanocomposite film is deposited and transformed to purely anatase titania nanostructures via calcination. In total, this procedure is repeated three times on top of the substrate. The approach is monitored with grazing incidence small angle X‐ray scattering after each fabrication step. With scanning electron microscopy the final hierarchical structure is imaged. From the characterization different structural levels are clearly identified.
Organic field‐effect transistors (OFETs) based on interconnected nanowire networks of P3HT have been successfully fabricated by using a mixed‐solvent method. The nanowire network density can be tuned by controlling the anisole/chlorobenzene ratio of mixed solvents. The obtained field‐effect mobility, threshold voltage and the ratio of on‐state current and off‐state current (Ion/Ioff) was 0.0435 cm2/V s, –10 V and 1.75 × 104, respectively. The three‐dimensional and interconnected nanowire structure of the networks can enhance the charge transport in P3HT.
Bulk polycrystalline La0.8Li0.2MnO3 is found to switch between a low‐resistance state and a high‐resistance state on thermal cycling. The low‐temperature, high‐resistance state exhibits strong electroresistance whereas the high‐temperature, low‐resistance state does not. The change in resistance between the two distinct states is of two orders of magnitude. It is proposed that the observed metastability may serve as the basis for resistive thermal‐switching devices.
We demonstrate the self‐catalyst growth of vertically aligned InAs nanowires on bare Si(111) by droplet epitaxy. The growth conditions of indium droplets suitable for nucleation and growth of nanowires have been identified. We have then realized vertically aligned and non‐tapered InAs nanowires on bare Si(111) substrates through optimal indium droplets. It was found that the lateral dimensions and density of nano‐wires are defined by the indium droplets. This technique unravels a controllable, cost‐effective and time‐efficient route to fabricating functional monolithic hybrid structures of InAs nanowires on silicon.
A new method for fabricating carbon nanotube‐conducting polymer (CNT‐CP) composite single nanowires is reported. The method developed is highly efficient, reliable, and economical because it obviates the time consuming process of template fabrication and the post‐synthesis task of positioning nanowires. Single nanowires with diameters of 50‐500 nm are fabricated between electrodes, self‐templated by dielectrophoresis and electropolymerization. Fabrication of an individually addressed nanowire array with cantilever electrodes on a microchip is demonstrated.
