Copoly(arylene ether nitrile) and copoly(arylene ether sulfone) ionomers with pendant sulfobenzoyl groups for proton conducting fuel cell membranes

Three series of fully aromatic ionomers with naphthalene moieties and pendant sulfobenzoyl side chains were prepared via K₂CO₃ mediated nucleophilic aromatic substitution reactions. The first series consisted of poly(arylene ether)s prepared by polycondensations of 2,6‐difluoro‐2′‐sulfobenzophenone (DFSBP) and 2,6‐dihydroxynaphthalene or 2,7‐dihydroxynaphthalene (2,7‐DHN). In the second series, copoly(arylene ether nitrile)s with different ion‐exchange capacities (IECs) were prepared by polycondensations of DFSBP, 2,6‐difluorobenzonitrile (DFBN), and 2,7‐DHN. In the third series, bis(4‐fluorophenyl)sulfone was used instead of DFBN to prepare copoly(arylene ether sulfone)s. Thus, all the ionomers had sulfonic acid units placed in stable positions close to the electron withdrawing ketone link of the side chains. Mechanically strong proton‐exchange membranes with IECs between 1.1 and 2.3 meq g⁻¹ were cast from dimethylsulfoxide solutions. High thermal stability was indicted by high degradation temperatures between 266 and 287 °C (1 °C min⁻¹ under air) and high glass transition temperatures between 245 and 306 °C, depending on the IEC. The copolymer membranes reached proton conductivities of 0.3 S cm⁻¹ under fully humidified conditions. At IECs above ∼1.6 meq g⁻¹, the copolymer membranes reached higher proton conductivities than Nafion^® in the range between −20 and 120 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Naphthalene‐based poly(arylene ether ketone) copolymers containing sulfobutyl pendant groups for proton exchange membranes

A new monomer 1,5‐bis(4‐fluorobenzoyl)‐2,6‐dimethoxynaphthalene (DMNF) was prepared and further polymerized to form naphthalene‐based poly(arylene ether ketone) copolymers containing methoxy groups (MNPAEKs). The side‐chain‐type sulfonated naphthalene‐based poly(arylene ether ketone) copolymers (SNPAEKs) were obtained by demethylation and sulfobutylation. Flexible and tough membranes with reasonably high mechanical strength were prepared. The SNPAEKs membrane showed anisotropic membrane swelling with larger swelling in thickness than in plane. Transmission electron microscopy (TEM) analysis revealed clear nanophase separated structure of SNPAEKs membranes, which composed of hydrophilic side chain and hydrophobic main‐chain domains. Proton conductivities of copolymers increased gradually with increase in temperature. The highest conductivity of 0.179 S/cm was obtained for SNPAEK‐80 (IEC = 1.82 mequiv/g) at 80 °C, which is higher than that of Nafion117 (0.146 S/cm). The SNPAEKs membranes exhibit the methanol permeability in the range of 3.42 × 10^?8?4.49 × 10^?7 cm²/s, which are much lower than that of Nafion117. They could be the promising materials as alternative to Nafion membrane for direct methanol fuel cells applications. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47:5772–5783, 2009     

Evaluation of proton conductivity of sulfonated polyimide/dihydroxy naphthalene charge‐transfer complex hybrid membranes

Sulfonated polyimide (SPI)/dihydroxynaphthalene (DHN) charge‐transfer (CT) complex hybrid films were investigated as possible alternative for polymer electrolyte membranes in polymer electrolyte fuel cells. SPI/DHN CT complex hybrid films include CT complexes, which might work as electronic conductors, and sulfonic acid units, which could work as proton conductors. Therefore, the origin of the conductivity of SPI/DHN complex hybrid films was evaluated by four‐probe impedance measurements in the through‐plane direction of the films. The obtained conductivity of the CT complex hybrid films increased with the increase of ion exchange capacity of the CT films and the decrease of CT complex concentration in the films. These results indicated that proton transfer dominantly occurred in the CT complex hybrid films. Proton conductivity of the CT complex hybrid films consisting of 2,6‐ or 1,5‐DHN showed the similar values, although the molecular geometries of the CT complex were different. The activation energy values for proton conductivity in the CT films were approximately the same as that of Nafion 212. Water uptake (WU) results were also conducted and suggest that CT complex formation could control the degree of WU of the films and prevent dissolution of SPI. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2991–2997     

Sulfonated poly(ether sulfone)s with binaphthyl units as proton exchange membranes for fuel cell application

Sulfonated poly(ether sulfone)s containing binaphthyl units (BNSHs) were successfully prepared for fuel cell application. BNSHs, which have very simple structures, were easily synthesized by postsulfonation of poly(1,1′‐dinaphthyl ether phenyl sulfone)s and gave tough, flexible, and transparent membranes by solvent casting. The BNSH membranes showed low water uptake compared to a typical sulfonated poly(ether ether sulfone) (BPSH‐40) membrane with a similar ion exchange capacity (IEC) value and water insolubility, even with a high IEC values of 3.19 mequiv/g because of their rigid and bulky structures. The BNSH‐100 membrane (IEC = 3.19 mequiv/g) exhibited excellent proton conductivity, which was comparable to or even higher than that of Nafion 117, over a range of 30–95% relative humidity (RH). The excellent proton conductivity, especially under low RH conditions, suggests that the BNSH‐100 membrane has excellent proton paths because of its high IEC value, and water insolubility due to the high hydrophobicity of the binaphthyl structure. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5827–5834, 2009     

Synthesis and characterization of sulfonated‐fluorinated,hydrophilic‐hydrophobic multiblock copolymers for proton exchange membranes

Hydrophilic/hydrophobic block copolymers as proton exchange membranes (PEMs) has become an emerging area of research in recent years. These copolymers were obtained through moderate temperature (～ 100 °C) coupling reactions, which minimize the ether‐ether interchanges between hydrophobic and hydrophilic telechelic oligomers via a nucleophilic aromatic substitution mechanism. The hydrophilic blocks were based on the nucleophilic step polymerization of 3,3′‐disulfonated, 4,4′‐dichlorodiphenyl sulfone with an excess 4,4′‐biphenol to afford phenoxide endgroups. The hydrophobic (fluorinated) blocks were largely based on decafluoro biphenyl (excess) and various bisphenols. The copolymers were obtained in high molecular weights and were solvent cast into tough membranes, which had nanophase separated hydrophilic and hydrophobic regions. The performance and structure‐property relationships of these materials were studied and compared to random copolymer systems. NMR results supported that the multiblock sequence had been achieved. They displayed superior proton conductivity, due to the ionic proton conducting channels formed through the self‐assembly of the sulfonated blocks. The nano‐phase separated morphologies of the copolymer membranes were studied and confirmed by atomic force microscopy. Through control of a variety of parameters, including ion exchange capacity and sequence lengths, performances as high, or even higher than those of the state‐of‐the‐art PEM, Nafion, were achieved. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1038–1051, 2009     

Comparative effect of phthalazinone units in sulfonated poly(arylene ether ether ketone ketone) copolymers as proton exchange membrane materials

A new series of aromatic poly(arylene ether ether ketone ketone) copolymers containing pendant sulfonic acid groups (SPAEEKK‐D) were synthesized from commercially available monomers 1,3‐bis(4‐fluorobenzoyl)‐benzene, sodium 6,7‐dihydroxy‐2‐naphthalenesulfonate, and 4‐(4‐hydroxyphenyl)‐2,3‐phthalazin‐1‐one (DHPZ). Structure–property relationships of the phthalazinone SPAEEKK‐D series poly(arylene ether ether ketone ketone) copolymer were compared with copolymers SPAEEKK‐B and SPAEEKK‐H containing different diols such as 4,4′‐biphenol and hydroquinone, respectively, prepared in our earlier work. Ion exchange capacity (IEC_w, weight‐based; IEC_v, volume‐based), thermal stabilities, swelling, proton and methanol transport properties of the membranes were investigated in relation to their structures and compared with those of perfluorinated ionomer (Nafion 117). The SPAEEKK‐D membrane incorporating the phthalazinone monomer DHPZ showed relatively lower water uptake and methanol permeability compared with earlier SPAEEKK‐B and SPAEEKK‐H membranes incorporating biphenol and hydroquinone monomers, respectively. Inclusion of phthalazinone in the SPAEEKK‐D copolymers led to lower water absorption, enabling increased proton exchange concentrations in the hydrated polymer matrix that resulted in more desirable membrane properties for future direct methanol fuel cell applications. The SPAEEKK‐D membranes also showed improved mechanical and thermal properties and oxidative stability compared with the earlier SPAEEKK‐B and ‐H membranes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 989–1002, 2008     

Influence of chemical composition and sequence length on the transport properties of proton exchange membranes

One of the integral parts of the fuel cell is the proton exchange membrane. Our research group has been engaged in the past few years in the synthesis of several sulfonated poly(arylene ether) random copolymers. The copolymers were varied in both the bisphenol structure as well as in the functional groups in the backbone such as sulfone and ketones. To compare the effect of sequence length, multiblock copolymers based on poly(arylene ether sulfone)s were synthesized. This paper aims to describe our investigation of the effect of chemical composition, morphology, and ion exchange capacity (IEC) on the transport properties of proton conducting membranes. The key properties examined were proton conductivity, methanol permeability, and water self diffusion coefficient in the membranes. It was observed that under fully hydrated conditions, proton conductivity for both random and block copolymers was a function of IEC and water uptake. However, under partially hydrated conditions, the block copolymers showed improved proton conductivity over the random copolymers. The proton conductivity for the block copolymer series was found to increase with increasing block lengths under partially hydrated conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2226–2239, 2006     

Synthesis and characterization of poly(arylene ether ketone)s bearing pendant sulfonic acid groups for proton exchange membrane materials

A bisphenol monomer (2,5‐dimethoxy)phenylhydroquinone was prepared and further polymerized to obtain poly(arylene ether ketone) copolymers containing methoxy groups. After demethylation and sulfobutylation, a series of novel poly(arylene ether ketone)s bearing pendant sulfonic acid group (SPAEKs) with different sulfonation content were obtained. The chemical structures of all the copolymers were analyzed by ¹H NMR and ¹³C NMR spectra. Flexible and tough membranes with reasonably good mechanical properties were prepared. The resulting side‐chain‐type SPAEK membranes showed good dimensional stability, and their water uptake and swelling ratio were lower than those of conventional main‐chain‐type SPAEK membranes with similar ion exchange capacity. Proton conductivities of these side‐chain‐type sulfonated copolymers were higher than 0.01 S/cm and increased gradually with increasing temperature. Their methanol permeability values were in the range of 1.97 × 10^?7–5.81 × 10^?7 cm²/s, which were much lower than that of Nafion 117. A combination of suitable proton conductivities, low water uptake, low swelling ratio, and high methanol resistance for these side‐chain‐type SPAEK films indicated that they may be good candidate material for proton exchange membrane in fuel cell applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Locally sulfonated poly(ether sulfone)s with highly sulfonated units as proton exchange membrane

Novel locally sulfonated poly(ether sulfone)s with highly sulfonated units were successfully synthesized for fuel cell applications. Poly(ether sulfone)s were prepared by the nucleophilic substitution of bis(4‐fluorophenyl) sulfone with 1,2,4,5‐tetrakis([1,1′‐biphenyl]‐2‐oxy)‐3,6‐bis(4‐hydroxyphenoxy)benzene and bis(4‐hydroxyphenyl) sulfide, followed by oxidation using m‐chloroperoxybenzoic acid. The desired highly sulfonated units were easily introduced by postsulfonation and each one had ten sulfonic acid groups. The sulfonated polymers gave tough, flexible, and transparent membranes by solvent casting. The high contrast in polarity between highly sulfonated units and hydrophobic poly(ether sulfone) units enabled the formation of defined phase‐separated structures and well‐connected proton paths. The sulfonated polymers exhibited excellent proton conductivity over a wide range of relative humidities. The proton conductivity of the sulfonated polymer with an ion exchange capacity value of 2.38 mequiv/g was comparable to that of Nafion 117 even at 30% relative humidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3444–3453, 2009     

Synthesis of highly sulfonated poly(arylene ether sulfone) random (statistical) copolymers via direct polymerization

Novel biphenol‐based wholly aromatic poly (arylene ether sulfones) containing pendant sulfonate groups were prepared by direct aromatic nucleophilic substitution polycondensation of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS) and biphenol. Copolymerization proceeded quantitatively to high molecular weight in N‐methyl‐2‐pyrrolidinone at 190°C in the presence of anhydrous potassium carbonate. Tough membranes were successfully cast from the control and the copolymers, which had a SDCDPS/DCDPS mole ratio of either 40:60 or 60:40 using N,N‐dimethylactamide; the 100% SDCDPS homopolymer was water soluble. Short‐term aging (30 min) indicates that the desired acid form membranes are stable to 220°C in air and conductivity values at 25°C of 0.110 (40%) and 0.170 S/cm (60%) were measured, which are comparable to or higher than the state‐of‐the art fluorinated copolymer Nafion 1135 control. The new copolymers, which contain ion conductivity sites on deactivated rings, are candidates as new polymeric electrolyte materials for proton exchange membrane (PEM) fuel cells. Further research comparing their membrane behavior to post‐sulfonated systems is in progress.     

Synthesis and characterization of partially disulfonated hydroquinone‐based poly(arylene ether sulfone)s random copolymers for application as proton exchange membranes

Partially disulfonated hydroquinone (HQ)‐based poly(arylene ether sulfone) random copolymers were synthesized and characterized for application as proton exchange membranes. The copolymer composition was varied in the degree of disulfonation. The copolymers were characterized by ¹H NMR, Differential Scanning Calorimetry (DSC), and other analytical techniques. The copolymer with a 25% degree of disulfonation showed the best balance between water uptake and proton conductivity. The copolymers showed substantially reduced methanol permeability compared with Nafion® and satisfactory direct methanol fuel cell performance. The methanol selectivity improved significantly in comparison to Nafion® 117. At a given ionic composition, the HQ‐based system showed higher water uptake and proton conductivity than the biphenol‐based (BPSH‐xx) poly(arylene ether sulfone)s copolymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 384–391, 2009     

Poly(phenylene oxide) copolymer anion exchange membranes

Poly(phenylene oxide) block and random copolymers are synthesized by oxidative polymerization of 2,6-dimethylphenol and 2,6-diphenylphenol for potential alkaline exchange membrane application. The copolymers are functionalized on the methyl substituted repeat units through a two-step process to produce pendent quaternary ammonium cationic groups. The amount of quaternary ammonium cations and the ion exchange capacity are quantified through titration measurements. Ionic conductivity of the copolymer membranes is measured by electrochemical impedance spectroscopy. Block copolymers show increased bromide conductivity at higher ion exchange capacities compared with the random copolymer analogs. The bromide conductivity for a block copolymer film with an ion exchange capacity of 1.27 mequiv/g reaches 26 mS/cm at 90 °C and 95% relative humidity. The hydroxide conductivity for the same film was measured to be 84 mS/cm at 80 °C and 95% relative humidity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1770–1778, 2013     

Synthesis and properties of multiblock copoly(arylene ether)s containing superacid groups for fuel cell membranes

A series of block copoly(arylene ether)s containing pendant superacid groups were synthesized, and their properties were investigated for fuel cell applications. Two series of telechelic oligomers, iodo‐substituted oligo(arylene ether ketone)s and oligo(arylene ether sulfone)s, were synthesized. The degree of oligomerization and the end groups were controlled by changing the feed ratio of the monomers. The nucleophilic substitution polymerization of the two oligomers provided iodo‐substituted precursor block copolymers. The iodo groups were converted to perfluorosulfonic acid groups via the Ullmann coupling reaction. The high degree of perfluorosulfonation (up to 83%) was achieved by optimizing the reaction conditions. Tough and bendable membranes were prepared by solution casting. The ionomer membranes exhibited characteristic hydrophilic/hydrophobic phase separation with large hydrophilic clusters (ca. 10 nm), which were different from that of our previous random copolymers with similar molecular structure. The block copolymer structure was found to be effective in improving the proton‐conducting behavior of the superacid‐modified poly(arylene ether) ionomer membranes without increasing the ion exchange capacity (IEC). The highest proton conductivity was 0.13 S/cm at 80 °C, 90% relative humidity, for the block copolymer ionomer membrane with IEC = 1.29 mequiv/g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Polymer blend for fuel cells based on SPEKK: Effect of cocontinuous morphology on water sorption and proton conductivity

Proton‐exchange membranes (PEM), suitable for micro and small sized fuel cells, were obtained by blending sulfonated poly(ether ketone ketone) (SPEKK) polymers with different ionic exchange capacity (IEC). This approach was used to limit the amount of swelling caused by water sorption without significantly decreasing the proton conductivity of the membrane. In particular a membrane with a cocontinuous biphasic morphology was obtained by blending two SPEKKs, with respectively, an IEC equal to 1.2 and 2.08 in the weight ratio 60/40, casted from 5% (w/v) solutions in dimethylacetamide. The effect of a cocontinuous morphology on water sorption and proton conductivity in comparison to neat SPEKK was investigated. In the range of temperatures between 40 and 70 °C, which is typical for small and micro fuel cells conditions, it was found that the ratio of proton conductivity to water sorption could be maximized. This has been attributed to the presence of percolative pathways for proton transport provided by the cocontinuous morphology along with the constraint effect of the less sulfonated component on the overall capacity of swelling of the membrane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 395–404, 2007     

Synthesis of sulfonated aromatic poly(ether amide)s and their application to proton exchange membrane fuel cells

A series of wholly aromatic sulfonated poly(ether amide)s (SPEAs) containing a sulfonic acid group on the dicarbonyl aromatic ring were prepared via a polycondensation reaction of sulfonated terephthalic acid (STA), terephthalic acid (TA), and aromatic diamine monomers. The degree of sulfonation was readily controlled by adjusting the monomer feed ratio of STA and TA in the polymerization process, and randomly sulfonated polymers with an ion exchange capacity (IEC) of 1.0–1.8 mequiv/g were prepared using this protocol. The chemical structures of randomly sulfonated polymers were characterized using NMR and FT‐IR spectroscopies. Gel permeation chromatography analysis of SPEAs indicated the formation of high‐molecular‐weight sulfonated polymer. Tough and flexible SPEA membranes were obtained from solution of N,N‐dimethylacetamide, and thermogravimetric analysis of these membranes showed a high degree of thermal stability. Compared with previously reported sulfonated aromatic polyamides, these new SPEAs showed a significantly lower water uptake of 10–30%. In proton conductivity measurements, ODA‐SPEA‐70 (IEC = 1.80 mequiv/g), which was obtained from polycondensation of 4,4′‐oxydianiline and 70 mol % STA, showed a comparable proton conductivity (105 mS/cm) to that of Nafion 117 at 80 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 485–496, 2009     

Sulfonated naphthalene dianhydride based polyimide copolymers for proton‐exchange‐membrane fuel cells. I. Monomer and copolymer synthesis

A novel sulfonated diamine, 3,3′‐disulfonic acid‐bis[4‐(3‐aminophenoxy)phenyl]sulfone (SA‐DADPS), was prepared from m‐aminophenol and disodium‐3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone. The conditions necessary to synthesize and purify SA‐DADPS in high yields were investigated in some detail. This disulfonated aromatic diamine, containing ether and sulfone linkages, was used to prepare N‐methyl‐2‐pyrrolidinone‐soluble, six‐membered ring polyimide copolymers containing pendent sulfonic acid groups by a catalyzed one‐step high‐temperature polycondensation in m‐cresol. These materials showed much improved hydrolytic stability with respect to phthalimides. High‐molecular‐weight film‐forming statistical copolymers with controlled degrees of disulfonation were prepared through variations in the stoichiometric ratio of disulfonated diamine (SA‐DADPS) in its soluble triethylamine salt form to several unsulfonated diamines. Three unsulfonated diamines, bis[4‐(3‐aminophenoxy)phenyl] sulfone, 4,4′‐oxydianiline, and 1,3‐phenylenediamine, were used to prepare the copolymers. The characterization of the copolymers by ¹H NMR, Fourier transform infrared, ion‐exchange capacity, and thermogravimetric analysis demonstrated that SA‐DADPS was quantitatively incorporated into the copolymers. Solution‐cast films of the sulfonated copolymers were prepared and afforded tough, ductile membranes with high glass‐transition temperatures. Methods were developed to acidify the triethylammonium salt membranes into their disulfonic acid form, this being necessary for proton conduction in a fuel cell. The synthesis and characterization of these materials are described in this article. Future articles will describe the performance of these copolymers as proton‐exchange membranes in hydrogen/air and direct methanol fuel cells. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 862–874, 2004     

Chemically stable hybrid polymer electrolyte membranes prepared by radiation grafting,sulfonation, and silane‐crosslinking techniques

To prepare a crosslinked hybrid polymer electrolyte membrane (PEM) with high chemical stability, a silane monomer, namely p‐styryltrimethoxysilane (StSi), was first grafted to poly(ethylene‐co‐tetrafluoroethylene) (ETFE) film by γ‐ray preirradiation. Hydrolysis‐condensation and sulfonation were then performed on the StSi‐grafted ETFE (StSi‐g‐ETFE) films to give them crosslinks and proton conductibility, respectively. Thus, a crosslinked proton‐conducting hybrid PEM was obtained. The crosslinks introduced by the silane‐condensation have an inorganic ? Si? O? Si? structure, which enhance the chemical and thermal stabilities of the PEM. The effect of the timing of the hydrolysis‐condensation (before or after sulfonation) and the sulfonation method (by chlorosulfonic acid or H₂SO₄) on the properties of the resulting hybrid PEMs such as ion‐exchange capacity, proton conductivity, water uptake, chemical stability, and methanol permeability were investigated to confirm their applicability in fuel cells. We conclude that the properties of the new crosslinked hybrid StSi‐grafted PEMs are superior to divinylbenzene (DVB)‐crosslinked styrene‐grafted membranes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5559–5567, 2008     

Sulfonated polysulfone with 1,3-1H-dibenzimidazole-benzene additive as a membrane for direct methanol fuel cells

1,3-1H-Dibenzimidazole-benzene (DBImBenzene) has been synthesized using phosphorus pentoxide-methanesulfonic acid (PPMA) as a solvent and dehydration agent and investigated as an additive (up to 2.0 wt.%) in sulfonated polysulfone (SPSf) membranes to promote proton conduction via acid–base interactions. The SPSf/DBImBenzene blend membranes with various DBImBenzene contents (0–2.0 wt.%) have been prepared and characterized by proton conductivity measurement and electrochemical polarization and methanol crossover measurements in direct methanol fuel cells (DMFCs). The blend membranes with DBImBenzene content of 0.5 and 1.0 wt.% show higher proton conductivities (3.4 and 2.9 × 10⁻⁴ S/cm, respectively) than plain SPSf (2.4 × 10⁻⁴ S/cm) even though the blend membranes have lower ion exchange capacity (0.81 and 0.75 mequiv./g, respectively) than plain SPSf (0.86 mequiv./g). The blend membranes exhibit better electrochemical performance in DMFC than plain SPSf membrane due to an enhancement in proton conductivity through acid–base interactions and lower methanol crossover.     

Synthesis and Properties of Novel Side‐Chain Sulfonated Poly(Arylene Ether Sulfone)s for Proton Exchange Membranes

A series of novel side‐chain sulfonated poly(arylene ether sulfone) (SPAES) multiblock and random copolymers were synthesized by condensation polymerization from a new disulfonated aryl sulfone monomer, 4,4′‐difluoro‐2,2′‐bis(3‐sulfobenzoyl)diphenyl sulfone disodium salt (DFBSPS). The chemical structures of DFBSPS and the SPAESs were characterized by proton nuclear magnetic resonance (¹H NMR) and Fourier transform infrared (FTIR) spectra. The SPAES membranes prepared by solution cast method exhibited high tensile strength (50–71 MPa) and high radical oxidative stability. They could keep their morphology and maintain proton conductivities after hydrolysis test in 95 °C water for 1000 h. They also showed smaller swelling ratio in in‐plane direction than in through‐plane direction and such an anisotropic effect was more significant for the multiblock copolymers than for the random ones. The multiblock copolymer membranes exhibited higher proton conductivity than the random ones with similar ion exchange capacities (IECs). Preliminary hydrogen‐oxygen fuel cell tests were performed at 60 °C and 80% relative humidity (RH). The results showed that the single cell equipped with the multibiock copolymer membrane SB3 exhibited 0.12 W cm^?2 higher maximum output power density than the one equipped with the random copolymer membrane SR3 (with the same IEC), indicating much better performance of the former. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2304–2313     

Effect of Sulfonation Degree on Performance of Proton Exchange Membranes for Direct Methanol Fuel Cells

A series of proton exchange membranes based on sulfonated polyarylene ether ketones(SPAEKs) was used to study the effect of sulfonation degree on proton conductivity, methanol permeation and performance of direct methanol fuel cells(DMFCs). Dependences of physical characteristics of the membranes, i. e., proton conductivity, water uptake, swelling ratio, methanol permeability and ion exchange capacity(IEC) were systematically studied. Both methanol permeability and proton conductivity of the SPAEK membrane grow rapidly as the increase in sulfonation degree since methanol molecules and protons share the same transfer channel. However,the methanol permeability plays more important role comparing to proton conductivity. As a result, the SPAEK membrane with a medium sulfonation degree(60%) was found to yield the best performance in a DMFC due to the acquirement of balanced conductivity and methanol permeability.