Linear polyurethanes made from threitol: Acetalized and hydroxylated polymers

A set of novel linear polyurethanes was synthesized by reaction in solution of 1,6‐hexamethylene diisocyanate (HDI) or 4,4′‐methylene‐bis(phenyl diisocyanate) with 2,3‐acetalized threitols, specifically, 2,3‐O‐methylidene‐L ‐threitol and 2,3‐O‐isopropylidene‐D ‐threitol. The polyurethanes containing acetalized threitols had weight‐average molecular weights between 40,000 and 65,000 Da. Most of them were amorphous and they displayed T_g higher than their unsubstituted analogs. Deprotection of acetalized polyurethanes by treatment with acid allowed preparing semicrystalline polyurethanes bearing two free hydroxyl groups in the repeating unit. The crystalline structure and crystallizability of the hydroxylated polyurethane made from HDI were investigated taken as reference the polyurethane made from 1,4‐butanediol and HDI. The hydrolytic degradability of threitol derived polyurethanes was comparatively evaluated under a variety of conditions. Highest degradation rates were obtained upon incubation at pH 10 at temperatures above T_g, the aliphatic hydroxylated polyurethane being the fastest degrading compound. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7996–8012, 2008     

Sugar‐based hydrophilic polyurethanes and polyureas

Novel linear homogeneous polyurethanes and polyureas with enhanced hydrophilic character have been successfully prepared from sugar‐based monomers having their hydroxyl groups free or partially protected. By the reaction of primary hydroxyl groups of xylitol with dimethyl hexamethylene dicarbamate (HMDC) or di‐tert‐butyl‐4,4′‐diphenyl methyl dicarbamate (MDC), two new linear semicrystalline polyurethanes [PU(X‐HMDC) and PU(X‐MDC)] have been prepared. Likewise, by the reaction of xylitol with the analogous diisocyanates hexamethylene diisocyanate (HMDI) or 4,4′‐methylenebis(phenyl isocyanate) (MDI), similar polyurethanes [PU(X‐HMDI) and PU(X‐MDI)] were obtained. However, these latter polyurethanes present some degree of crosslinking because of the higher reactivity of the diisocyanate comonomers. Linear hydrophilic polyureas having free hydroxyl groups joined to the main chain have also been prepared by the reaction of the same diisocyanates (HMDI and MDI) with 1,6‐diamino‐1,6‐dideoxy‐D ‐mannitol and 1,6‐diamino‐1,6‐dideoxy‐3:4‐O‐isopropylidene‐D ‐mannitol. As far as we are aware, this kind of polyhydroxylated polyurea has not been previously described in the literature. The new polymers were characterized by standard methods (elemental analyses, gel permeation chromatography, IR, and NMR). The polyurethanes were hydrolytically degradable under physiological conditions, in contrast with less‐hydrophilic linear polyurethanes previously described. The thermal properties of the novel polymers were investigated by thermogravimetric analysis and differential scanning calorimetry. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Stereoregular poly‐O‐methyl [m,n]‐polyurethanes derived from D‐mannitol

Novel linear carbohydrate‐derived [m,n]‐polyurethanes are successfully prepared using D ‐mannitol as renewable and low cost starting material. The key comonomer, 1,6‐di‐O‐phenylcarbonyl‐2,3,4,5‐tetra‐O‐methyl‐D ‐mannitol is polymerized with a diamine synthesized from D ‐mannitol or with alkylenediamines. These polymerization reactions afford, respectively, a [6,6]‐polyurethane entirely based on a carbohydrate derivative or [m,n]‐polyurethanes constituted by a poly‐O‐methyl substituted unit alternating with a polymethylene chain. All these polymers are stereoregular, as result of the C₂ axis of symmetry of mannitol. The optically active polyurethanes are characterized by standard methods (FTIR, RMN, GPC, TGA, and DSC). Thus, GPC analysis reveals weight‐average molecular weights between 18,000 and 25,000 Da. Thermal studies (DSC) indicate that the polymers obtained are amorphous materials with T_g values dependent on the structure and chain length of the diamine constituent. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis,characterization, and properties of polyurethanes containing 1,4:3,6‐dianhydro‐D‐sorbitol

Two‐ and three‐component polyurethanes containing 1,4:3,6‐dianhydro‐D ‐sorbitol (isosorbide) derived from glucose were synthesized using n‐BuSn(?O)OH·H₂O as a catalyst, and the thermal properties (T_g, T_d) of the polymers were investigated by differential scanning calorimetry and thermogravimetric analysis. We carried out molds for polyurethanes, the molds of polyurethanes were obtained. The dynamic mechanical analyzes showed that the storage modulus values of the three‐component polymers were constant to a higher temperature than those of the two‐component polymers. The storage moduli (E′), loss moduli (E″), and values of tan δ for the polymers were obtained. The rigidity of three‐component polymers was increased by the introduction of bisphenol A and diphenylmethane group to two‐component polymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6025–6031, 2009     

Carbohydrate‐based copolyesters made from bicyclic acetalized galactaric acid

Mixtures of the dimethyl esters of adipic acid and 2,3:4,5‐di‐O‐methylene‐galactaric acid (Galx) were made to react in the melt with either 1,6‐hexanediol or 1,12‐dodecanediol to produce linear polycyclic copolyesters with aldarate unit contents varying from 10 up to 90 mole %. The copolyesters had weight–average molecular weights in the ～35,000–45,000 g mol^?1 range and a random microstructure, and were thermally stable up to nearly 300 °C. They displayed T_g in the ‐50 to ‐7 °C range with values largely increasing with the content in galactarate units. All the copolyesters were semicrystalline with T_m between 20 and 90 °C but only those made from 1,12‐dodecanediol were able to crystallize from the melt at a crystallization rate that decreased as the contents in the two comonomers approached each other. Copolyesters containing minor amounts of galactarate units adopted the crystal structure characteristic of aliphatic polyesters but a new crystal polymorph was formed when the cyclic sugar units became the majority. Stress–strain parameters were sensitively affected by composition of the copolyesters with the mechanical behavior changing from flexible/ductile to stiff/brittle with the replacement of adipate units by the galactarate units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Pseudopoly(amino acid)s: Copolymerization of trans‐4‐hydroxy‐L‐proline and α‐hydroxy acids

A series of novel copolymers of trans‐4‐hydroxy‐L ‐proline (Hpr) and α‐ hydroxy acids [D,L ‐mandelic acid (DLMA) and D,L ‐lactic acid (DLLA)] were synthesized via direct melt copolymerization with stannous octoate as a catalyst. These new copolymers had pendant amine functional groups along the polymer backbone chain. The optimal reaction conditions for the synthesis of the copolymers were obtained with 4 wt % stannous octoate at 140 °C under vacuum for 16 h. The synthesized copolymers were characterized by IR spectrophotometry, proton nuclear magnetic resonance, differential scanning calorimetry, and Ubbelohde viscometry. The effects of the kinds of comonomers and the comonomer molar ratio on the polycondensation and glass‐transition temperature (T_g) were investigated. The T_g's of the copolymers shifted to lower temperatures with an increasing comonomer molar ratio. As expected, the T_g's of the N‐Z‐Hpr/DLMA copolymers were higher than the N‐Z‐Hpr/DLLA copolymers, the pendant groups on the monomers (N‐Z‐Hpr) became larger and more flexible, and the T_g's of the resulting polymers declined. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 724–731, 2001     

Synthesis and properties of bio‐based polyurethanes bearing hydroxy groups derived from alditols

Four kinds of bio‐based polyurethanes bearing hydroxy groups in the pendants were synthesized by the polyaddition of D ‐mannitol‐ and D,L ‐erythritol‐derived diols (1,2:5,6‐di‐O‐isopropylidene‐D ‐mannitol and 1,2‐O‐isopropylidene‐D,L ‐erythritol) with hexamethylene diisocyanate and methyl (S)‐2,6‐diisocyanatohexanoate and the subsequent deprotection of the isopropylidene groups. They were hydrolyzed much more quickly than the corresponding protected polyurethanes at 50 °C and pH 7.0, although their hydrolytic degradation rate was lower than that of polyurethanes with saccharic and glucuronic lactone groups, which had been reported in our previous articles. The introduction of D ‐mannitol units to the polyether‐polyurethanes containing poly(oxytetramethylene) glycol units also enhanced their hydrolyzibility. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Block and random copolymerization of ε‐caprolactone,L‐, and rac‐lactide using titanium complex derived from aminodiol ligand

A series of di‐ and triblock copolymers [poly(L ‐lactide‐b‐ε‐caprolactone), poly(D,L ‐lactide‐b‐ε‐caprolactone), poly(ε‐caprolactone‐b‐L ‐lactide), and poly(ε‐caprolactone‐b‐L ‐lactide‐b‐ε‐caprolactone)] have been synthesized successfully by sequential ring‐opening polymerization of ε‐caprolactone (ε‐CL) and lactide (LA) either by initiating PCL block growth with living PLA chain end or vice versa using titanium complexes supported by aminodiol ligands as initiators. Poly(trimethylene carbonate‐b‐ε‐caprolactone) was also prepared. A series of random copolymers with different comonomer composition were also synthesized in solution and bulk of ε‐CL and D,L ‐lactide. The chemical composition and microstructure of the copolymers suggest a random distribution with short average sequence length of both the LA and ε‐CL. Transesterification reactions played a key role in the redistribution of monomer sequence and the chain microstructures. Differential scanning calorimetry analysis of the copolymer also evidenced the random structure of the copolymer with a unique T_g. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Solvent‐free and nonisocyanate melt transurethane reaction for aliphatic polyurethanes and mechanistic aspects

A novel melt transurethane polycondensation route for polyurethanes under solvent‐free and nonisocyanate condition was developed for soluble and thermally stable aliphatic or aromatic polyurethanes. The new transurethane process was investigated for A + B, A‐A + B, and A‐A + B‐B (A‐urethane and B‐hydroxyl) ‐type condensation reactions, and also monomers bearing primary and secondary urethane or hydroxyl functionalities. The transurethane process was confirmed by ¹H and ¹³C NMR, and molecular weight of the polymers were obtained as M_n = 10–15 × 10³ and M_w = 15–45 × 10³ g/mol. The mechanistic aspects of the melt transurethane process and role of the catalyst were investigated using model reactions, ¹H NMR, and MALDI‐TOF‐MS. The model reactions indicated the occurrence of 97% reaction in the presence of catalyst, whereas its absence gave only less than 2% of the product. The polymer samples were subjected for end‐group analysis using MALDI‐TOF‐MS, which confirms the Ti‐catalyst mediated nonisocyanate pathway in the melt transurethane process. Almost all the polyurethanes were stable up to 280 °C, and the T_g of the polyurethanes can be easily fine‐tuned from ?30 to 120 °C by using appropriate diols in the melt transurethane process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2445–2458, 2008     

Biodegradable polymers based on renewable resources. VII. Novel random and alternating copolycarbonates from 1,4:3,6‐dianhydrohexitols and aliphatic diols

Novel copolycarbonates containing 1,4:3,6‐dianhydro‐D ‐glucitol or 1,4:3,6‐dianhydro‐D ‐mannitol units, with various methylene chain lengths, were synthesized by bulk and solution polycondensations, of several combinations of carbonate‐modified sugar derivatives and aliphatic diols. Bulk polycondensations of 1,4:3,6‐dianhydro‐2,5‐bis‐O‐(phenoxycarbonyl)‐D ‐glucitol or 1,4:3,6‐dianhydro‐2,5‐bis‐O‐(phenoxycarbonyl)‐D ‐mannitol with four α,ω‐alkanediols having methylene chain lengths of 4, 6, 8, and 10, respectively, at 180 °C afforded the corresponding copolycarbonates with number‐average molecular weight (M_n) values up to 19.₂ × 10³. ¹³C NMR analysis disclosed that these polymers had scrambled structures in which the sugar carbonate and aliphatic carbonate moieties were nearly randomly distributed along a polymer chain. However, solution polycondensations between 1,4:3,6‐dianhydro‐2,5‐bis‐O‐(p‐nitrophenoxycarbonyl)‐D ‐glucitol or 1,4:3,6‐dianhydro‐2,5‐bis‐O‐(p‐nitrophenoxycarbonyl)‐D ‐mannitol, and the α,ω‐alkanediols in sulfolane or dimethyl sulfoxide at 60 °C gave well‐defined copolycarbonates having regular structures consisting of alternating sugar carbonate and aliphatic carbonate moieties with M_n values up to 33.₈ × 10³. Differential scanning calorimetry demonstrated that all the copolycarbonates were amorphous with glass‐transition temperatures ranging from 1 to 65 °C, which decreased with increasing lengths of the methylene chain of the aliphatic diols. Additionally, all the copolycarbonates were stable up to 310–330 °C as estimated by thermogravimetric analysis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2312–2321, 2003     

Demonstration of isospecific free radical polymerization of acrylate controlled by conformation and chirality of monomer

Radical polymerization of lactic acid‐based chiral and achiral methylene dioxolanones, a model for conformationally s‐cis locked acrylate, was carried out with AIBN to demonstrate an isospecific free radical polymerization controlled by chirality and conformation of monomer. Polymerization of the dioxolanones proceeded smoothly without ring opening to give a polymer with moderate molecular weight and 100% of maximum isotacticity. ESR spectrum indicated a twisted conformation of the growing poly(methylene dioxolanone) radical in contrast to an acyclic analogous radical, suggesting a restriction of the free rotation around main chain C_α? C_β bond of the growing radical center. Chirality as well as the polarity and bulkiness of monomer affected the polymer tacticity, and chiral alkyl substituent would afford a high isotactic polymer, in which higher the enantiomeric excess of the monomer was, higher the isotacticity of the polymer was. While, achiral or polar substituents including dibenzyl and trichloromethyl groups would afford an atactic polymer. In addition, glass transition temperature (T_g) of the resulting polymers was significantly high, ranging from 172.2 to 229.8 °C, and even for an isotactic polymer T_g was as high as 206.8 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2007–2016     

Synthesis and properties of hyperbranched polyurethanes,hyperbranched polyurethane copolymers with and without ether and ester groups using blocked isocyanate monomers

Starting from 3,5‐diamino benzoic acid, 2‐hydroxy propyl[3,5‐bis{(benzoxycarbonyl)imino}]benzyl ether, an AB₂‐type blocked isocyanate monomer with flexible ether group, and 2‐hydroxy propyl[3,5‐bis{(benzoxycarbonyl)imino}]benzoate, an AB₂‐type blocked isocyanate monomer with ester group, were synthesized for the first time. Using the same starting compound, 3,5‐bis{(benzoxycarbonyl)imino}benzylalcohol, an AB₂‐type blocked isocyanate monomer, was synthesized through a highly efficient short‐cut route. Step‐growth polymerization of these monomers at individually optimized experimental conditions results in the formation of hyperbranched polyurethanes with and without ether and ester groups. Copolymerizations of these monomers with functionally similar AB monomers were also carried out. The molecular weights of the polymers were determined using GPC and the values (M_w) were found to vary from 1.5 × 10⁴ to 1.2 × 10⁶. While hyperbranched polyurethanes having no ether or ester group were found to be thermally stable up to 217 °C, hyperbranched poly(ether–urethane)s and poly(ester–urethane)s were found to be thermally stable up to 245 and 300 °C, respectively. Glass transition temperature (T_g) of polyurethane was reduced significantly when introducing ether groups into the polymer chain, whereas T_g was not observed even up to 250 °C in the case of poly(ester–urethane). Hyperbranched polyurethanes derived from all the three different AB₂ monomers were soluble in highly polar solvents and the copolymers showed improved solubility. Polyethylene glycol monomethyl ether of molecular weight 550 and decanol were used as end‐capping groups, which were seen to affect the thermal, solution, and solubility properties of polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3877–3893, 2007     

New amorphous perfluoro polymers: perfluorodioxolane polymers for use as plastic optical fibers and gas separation membranes

To address the need for perfluoro polymers with higher T_g, we have prepared and characterized various perfluorodioxolane monomers via direct fluorination of the hydrocarbon precursors. These monomers were readily polymerized in bulk or in solution initiated by perfluorodibenzoyl peroxide. The polymers obtained have relatively high T_g(~160°C) and exhibited low material dispersion. These polymers are completely amorphous and soluble in fluorinated solvents. The polymers are also chemically and thermally stable (T_g > 300°C). Thus, these perfluorodioxolane polymers may be used as plastic optical fiber material where high T_g is required, such as in automobile and aircraft application. These perfluorodioxolane polymers were also investigated for use as gas separation membrane. Among these polymers, the copolymer of perfluoro (2‐methylene‐1,3‐dioxolane) and perfluoro (2‐methylene‐4,5‐dimethyl dioxolane) showed superior gas separation performance compared with the commercial perfluoro polymers for a number of gas pair, including CO₂/CH₄, H_e/CH₄, H₂/CH₄, and N₂/CH₄. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and properties of segmented main‐chain liquid‐crystalline polyurethanes with a high aspect ratio mesogenic diol as a chain extender

Main‐chain liquid‐crystalline polyurethanes were synthesized based on a high aspect ratio mesogenic diol (4‐{[4‐(6‐hydroxyhexyloxy)‐phenylimino]‐methyl}‐benzoic acid 4‐{[4‐(6‐hydroxyhexyloxy)‐phenylimino]‐methyl}‐phenyl ester) as a chain extender; polycaprolactone (PCL) diol soft segments of different number‐average molecular weights (530, 1250, or 2000); and different diisocyanates, including 1,4‐hexamethylene diisocyanate (HMDI), 4,4′‐methylene bis(cyclohexyl isocyanate) (H₁₂MDI), and 4,4′‐methylene bis(phenyl isocyanate) (MDI). The structure of the polymers was confirmed with Fourier transform infrared spectroscopy, and differential scanning calorimetry and polarizing microscopy measurements were carried out to examine the liquid‐crystalline and thermal properties of the polyurethanes, respectively. The mesogenic diol was partially replaced with 20–50 mol % PCL. A 20 mol % mesogen content was sufficient to impart a liquid crystalline property to all the polymers. The partial replacement of the mesogenic diol with PCL of various molecular weights, as well as the various diisocyanates, influenced the phase transitions and the occurrence of mesophase textures. Characteristic liquid‐crystalline textures were observed when a sufficient content of the mesogenic diol was present. Depending on the flexible spacer length and the mesogenic content, grained and threadlike textures were obtained for the HMDI and H₁₂MDI series polymers, whereas the polyurethanes prepared from MDI showed only grained textures for all the compositions. The polymers formed brittle films and could not be subjected to tensile tests. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1527–1538, 2002     

Poly(methyl methacrylate) copolymers containing multiple,pendent plasticizing groups

New ether dimer (ED‐Eh) and diester (EHDE) derivatives of α‐(hydroxymethyl)acrylate, each having two 2‐ethylhexyl side chains, and an amine‐linked di(2‐ethylhexyl)acrylate (AL‐Eh), having three 2‐ethylhexyl side chains, were synthesized and (co)polymerized to evaluate the effects of differences in the structures of the monomers on final (co)polymer properties, particularly glass transition temperature, T_g. The free radical polymerizations of these monomers yielded high‐molecular–weight polymers. Cyclopolymer formation of ED‐Eh and AL‐Eh was confirmed by ¹³C NMR analysis and the cyclization efficiencies were found to be very high (～100%). Copolymers of ED‐Eh, EHDE, and AL‐Eh with methyl methacrylate (MMA) showed significant T_g decreases over poly(methyl methacrylate) (PMMA) due to 2‐ethylhexyl side groups causing “internal” plasticization. Comparison of the T_g's of the copolymers of 2‐ethylhexyl methacrylate, ED‐Eh, EHDE, and AL‐Eh with MMA revealed that the impacts of these monomers on depression of T_g's are identical with respect to the total concentration of the pendent groups. This is consistent with an earlier study involving copolymers of monomers comprising one and two octadecyl side groups with MMA. That is, the magnitude of decrease in T_g's was quantitatively related to the number of the 2‐ethylhexyl pendent groups in the copolymers rather than their placement on the same or randomly incorporated repeat units. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2302–2310, 2010     

Hydroxyl‐ and amine‐terminated hyperbranched polyurethanes using AB2‐type azide monomers: Synthesis,characterization, fluorescence,and charge‐transfer complexation studies

Novel AB₂‐type azide monomers such as 3,5‐bis(4‐methylolphenoxy)carbonyl azide (monomer 1) , 3,5‐bis(methylol)phenyl carbonyl azide (monomer 2) , 4‐(methylol phenoxy) isopthaloyl azide (monomer 3) , and 5‐(methylol) isopthaloyl azide (monomer 4) were synthesized. Melt and solution polymerization of these monomers yielded hydroxyl‐ and amine‐terminated hyperbranched polyurethanes with and without flexible ether groups. The structures of theses polymers were established using FT‐IR and NMR spectroscopy. The molecular weights (M_w) of the polymers were found to vary from 3.2 × 10³ to 5.5 × 10⁴ g/mol depending on the experimental conditions used. The thermal properties of the polymers were evaluated using TGA and DSC: the polymer obtained from monomer ( 1 ) exhibited lowest T_g and highest thermal stability and the polymer obtained from monomer ( 2 ) registered the highest T_g and lowest thermal stability. All the polymers displayed fluorescence maxima in the 425–525 nm range with relatively narrow peak widths indicating that they had pure and intense fluorescence. Also, the polymers formed charge transfer (CT) complexes with electron acceptor molecules such as 7,7,8,8‐tetracyano‐quino‐dimethane (TCNQ) and 1,1,2,2‐tetracyanoethane (TCNE) as evidenced by UV‐visible spectra. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3337–3351, 2009     

Linear polyurethanes derived from alditols and diisocyanates

A set of linear [m,n]‐type polyurethanes was synthesized by polycondensation in solution from hexamethylene diisocyanate and 4,4′‐methylene‐bis(phenyl isocyanate) with alditols. Threitol, arabinitol, and xylitol bearing the secondary hydroxy groups blocked as methyl ethers were used. Either regioregular or nonregioregular polymers (depending on the configuration of the alditol) were obtained in high yields and with number‐average molecular weights within the 20,000–30,000 range. All these polyurethanes were amorphous with T_g being highly dependent on the aliphatic or aromatic nature of the diisocyanate used, but scarcely depending on the chemical structure of the alditol moiety. They were found to be stable up to near 300 °C, decomposing at higher temperatures through a complex three‐stage mechanism. Polyurethanes obtained from threitol did not show significant enhancement of hydrolytic degradability as compared with polyurethanes obtained from 1,4‐butanediol. Conversely, polyurethane prepared from xylitol and hexamethylendiisocyanate was found to be almost fully hydrolyzed in 1 month when incubated in water either at 80 °C and pH 7.4 or at 37 °C and pH 10. It was concluded that the alditol size seems to be of prime importance in determining the hydrodegradability of these sugar containing polyurethanes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4109–4117, 2007     

Melt transesterification and characterization of segmented block copolyesters containing 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol

Conventional melt transesterification successfully produced high‐molecular‐weight segmented copolyesters. A rigid, high‐T_g polyester precursor containing the cycloaliphatic monomers, 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol, and dimethyl‐1,4‐cyclohexane dicarboxylate allowed molecular weight control and hydroxyl difunctionality through monomer stoichiometric imbalance in the presence of a tin catalyst. Subsequent polymerization of a 4000 g/mol polyol with monomers comprising the low‐T_g block yielded high‐molecular‐weight polymers that exhibited enhanced mechanical properties compared to a nonsegmented copolyester controls and soft segment homopolymers. Reaction between the polyester polyol precursor and a primary or secondary alcohol at melt polymerization temperatures revealed reduced transesterification of the polyester hard segment because of enhanced steric hindrance adjacent to the ester linkages. Differential scanning calorimetry, dynamic mechanical analysis, and tensile testing of the copolyesters supported the formation of a segmented multiblock architecture. Further investigations with atomic force microscopy uncovered unique needle‐like, interconnected, microphase separated surface morphologies. Small‐angle X‐ray scattering confirmed the presence of microphase separation in the segmented copolyesters bulk morphology. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

One‐pot synthesis of hyperbranched glycopolymers by RAFT polymerization

Soluble hyperbranched glycopolymers were prepared by copolymerization of glycan monomers with reversible addition‐fragmentation chain transfer polymerization (RAFT) inimers in a simple one‐pot reaction. Two novel RAFT inimers, 2‐(methacryloyloxy)ethyl 4‐cyano‐4‐(phenylcarbonothioylthio)pentanoate (MAE‐CPP) and 2‐(3‐(benzylthiocarbonothioylthio)propanoyloxy)ethyl acrylate (BCP‐EA) were synthesized and used to prepare hyperbranched glycopolymers. Two types of galactose‐based saccharide monomers, 6‐O‐methacryloyl‐1,2:3,4‐di‐O‐isopropylidene‐D ‐galactopyranose (proGal‐M) and 6‐O‐(2′‐acrylamido‐2′‐methylpropanoate)‐1,2:3,4‐di‐O‐isopropylidene‐D ‐galactopyranose (proGal‐A), containing a methacrylate and an acrylamide group, respectively, were also synthesized and polymerized under the mediation of the MAE‐CPP and BCP‐EA inimers, respectively. In addition, hyperbranched poly(proGal‐M), linear poly(proGal‐A), and hyperbranched poly(proGal‐A) were generated and their polymerization kinetics were studied and compared. An unexpected difference was observed in the kinetics between the two monomers during polymerization: the relationship between polymerization rate and concentration of inimer was totally opposite in the two monomer–inimer systems. Branching analysis was conducted by using degree of branching (DB) as the measurement parameter. As expected, a higher DB occurred with increased inimer content. Furthermore, these polymers were readily deprotected by hydrolysis in trifluoroacetic acid solution resulting in water‐soluble polymers. The resulting branched glycopolymers have potential as biomimetics of polysaccharides. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Design and synthesis of highly photopolymerizable styrenyl compounds in solid‐state photoinitiated polymerization

We designed a new type of styrenyl compound applicable to conventional photopolymerization systems, aiming at the production of polymers with improved mechanical properties, resistance to chemicals, and elevated glass‐transition temperatures (T_g's). A series of styrenyl monomers bearing 2,5‐dithio‐1,3,4‐thiadiazole groups were prepared, and their reactivity was studied in solid‐state photopolymerization initiated by 2‐(4′‐methoxystyryl)‐4,6‐bis(trichloromethyl)‐1,3,5‐triazine. These monomers exhibited much higher polymerization rates than usual, and the final conversion nearly reached completion, despite the relatively high T_g of the solid‐state photopolymerization system. Even at temperatures below T_g, the polymerization proceeded without a ceiling phenomenon. These features were explained by intermolecular interactions between the monomers that induced monomer alignments effective for solid‐state polymerization, large excess free volumes arising from rotation around the methylthio groups, and intramatrix radical migration leading to encounters with the remaining monomers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3227–3242, 2003