Persistent layer‐by‐layer growth is demonstrated for pulsed‐laser homoepitaxy of ZnO thin films on $(000\bar 1)$ ZnO single crystals. Employing interval pulsed‐laser deposition (PLD), RHEED oscillations are stabilized over a film thickness of about 90 nm. For interval pulsed laser deposited films a considerably decreased root‐mean‐square surface roughness of 0.26 nm was found, in comparison to 0.74 nm for conventional PLD. A small asymmetry in the X‐ray diffraction (XRD) 2θ –ω scan reveals compressive strain in the thin film being slightly larger for interval PLD as compared to conventional PLD. The FWHM of the photoluminescence (PL) I6 line is higher with about 500 µeV as compared to 350 µeV for the conventional PLD. Consequently, both XRD as well as PL indicate a slightly higher amount of charged defects for the interval PLD.
We report the fabrication procedure and the characterization of an Al0.3Ga0.7As solar cell containing high‐density GaAs strain‐free quantum dots grown by droplet epitaxy. The production of photocurrent when two sub‐bandgap energy photons are absorbed simultaneously is demonstrated. The high quality of the quantum dot/barrier pair, allowed by the high quality of nanostructured strain‐free materials, opens new opportunities for quantum dot based solar cells.
We propose a theory of thin film photovoltaics in which one of the polycrystalline films is made of a pyroelectric material grains such as CdS. That film is shown to generate strong polarization improving the device open circuit voltage. Implications and supporting facts for the major photovoltaic types based on CdTe and CuIn(Ga)Se2 absorber layers are discussed.
Osmium diboride has been known for some time as a low compressibility material and a superhard material. It is suitable for hard coating applications. It is also a superconductor below 2.1 K. Using first‐principles calculations, the author investigated the geometry of its Fermi surface (FS) and calculated the related physical quantities. The theoretical results are used to predict the frequencies of the Shubnikov–de Haas quantum oscillations. Comparison with recent measurements of the magneto‐resistance oscillations in osmium diboride is made.
Bi2Te3 doped p‐type Pb0.13Ge0.87Te samples were prepared by hot pressing. We report on very high power factor values of ～30 μW/cm K2 at 500 °C, as were determined from Seebeck coefficient and electrical resistivity measurements. From dilatometric characterization, the phase transition from the low temperature rhombohedral to the high temperature cubic NaCl structures, takes place at 373 °C. This transition is accompanied by a continuous and gradual change of the lattice parameters, as was observed by hot stage XRD, suggesting a good mechanical durability upon thermal cycling and operating in large thermal gradients.
This Letter reports on the assembly on the tip of an optical fibre of a metamaterial film fabricated by a self‐assembly bottom‐up method, composed of silver nanowires embedded in an alumina matrix. By illuminating the film through the fibre in a reflection configuration, we observe experimentally the optical response of the metamaterial in agreement with theoretical predictions and interpreted as the excitation of surface plasmon‐polaritons in the cylindrical surface of the nanowires. These results pave the way for low‐cost optical fibre devices that incorporate metamaterial films.
InGaN/GaN light‐emitting diodes (LEDs) are known to exhibit a strongly non‐uniform vertical carrier distribution within the multi‐quantum well (MQW) active region. We propose to eliminate “dark” quantum wells by insertion of multiple tunnel junctions into the MQW which allow for the repeated use of electrons and holes for photon generation. In good agreement with available measurements, we demonstrate by self‐consistent numerical simulation that such tunnel junction LED design promises quantum efficiencies as high as 250% as well as a strongly enhanced output power at high input power, compared to conventional LED concepts.
We report a stacked Y2O3/TiOx resistive random access memory (RRAM) device, showing good high‐temperature switching characteristics of extremely low reset current of 1 μA at 150 °C, large off/on resistance window (>200) at 150 °C, large rectification ratio of ～300 at 150 °C and good current distribution at 85 °C. The good rectifying property, lower high‐temperature sneak current and tighter high‐temperature current distribution can be attributed to the combined results of the oxygen vacancies in TiOx and the related carrier depletion effect.
Optically transparent and high‐quality hybrid ZnO nanoparticle and anthracene embedded polyphenylsiloxane (PPS) glass films were spin‐coated on quartz substrates. A strong Förster resonant energy transfer (FRET) process was indicated by the observation of quenching of the ZnO emission and an enhancement of the anthracene emission at room temperature. The efficiency of this energy transfer between ZnO and the S1 vibronic states of the anthracene molecules can be optimized to exceed 90%.
Polymer nanocomposites containing different concentrations of Au nanoparticles have been investigated by small angle X‐ray scattering and electronic absorption spectroscopy. The variation in the surface plasmon resonance (SPR) band of Au nanoparticles with concentration is described by a scaling law. The variation in the plasmon band of ReO3 nanoparticles embedded in polymers also follows a similar scaling law.
We report on solution‐processible polymer solar cells (PSCs) fabricated on a papery substrate using carton. Highly conductive PEDOT:PSS was used as a bottom anode and planarization layer, and a semi‐transparent top cathode was applied. This research could be an important approach to the development of all‐solution‐processible papery PSCs as well as paper electronics.
Steady‐state and time‐resolved photoluminescence of silicon nanoparticles dispersed in low‐polar liquids at above room temperature is studied. The roles of low‐polar liquids as well as mechanisms responsible for their temperature‐dependent photoluminescence are discussed. The thermal sensitivity of the photoluminescence is estimated and application of the nanoparticles as nanothermometers is proposed.
We study graphene growth on hafnia (HfO2) nanoparticles by chemical vapour deposition using optical microscopy, high resolution transmission electron microscopy and Raman spectroscopy. We find that monoclinic HfO2 nanoparticles neither reduce to a metal nor form a carbide while nucleating nanometer domain‐sized few layer graphene. Hence we regard this as an interesting non‐metallic catalyst model system with the potential to explore graphene growth directly on a (high‐k) dielectric.
Lead carbonate chloride, Pb2CO3Cl2, known as mineral phosgenite, is introduced as a novel SRS‐active carbonate crystal with tetragonal symmetry. Under picosecond one‐micron laser pumping Raman‐induced χ(3)‐nonlinear generation in the near‐IR is observed. All recorded high‐order Stokes and anti‐Stokes sidebands are identified and attributed to two SRS‐promoting vibration modes with ωSRS1 ≈ 1062 cm–1 and ωSRS2 ≈ 86 cm–1.
The BOSCO solar cell represents a bifacial structure with double‐sided collection. The structure allows the use of standard module interconnection technology and favours the use of material with low to medium diffusion length and low resistivity for maximum benefit towards other structures, such as Al‐BSF and PERC. Within this work, we present first results on different multicrystalline silicon materials yielding a monofacial efficiency of 17.4% on large‐area wafers from block‐cast mc‐Si. This value represents a gain of ～0.7%abs compared to Al‐BSF cells processed in parallel. The applicability for bifacial operation is demonstrated by a significantly increased quantum efficiency for rear side illumination. These results make the BOSCO solar cell concept a promising candidate to further boost the output of utility‐scale PV plants even when using low‐cost wafers of low to medium diffusion length material.
Nanostructures formed in a titanium dioxide (TiO2)–poly(styrene)‐block‐poly(ethyleneoxide) nanocomposite film on top of fluor‐doped tin oxide (FTO) layers are investigated. The combinatorial approach is based on probing a wedge‐shaped FTO‐gradient with grazing incidence small angle X‐ray scattering (GISAXS) in combination with a moderate micro‐focus X‐ray beam. The characteristic lateral length is given by adjacent nanowire‐shaped TiO2 regions. It decreases from 200 nm on the thick FTO layer to 90 nm on the bare glass surface.
The crystallization process of mechanically alloyed Fe75Zr25 metallic glasses is investigated by means of both thermo‐magnetization and in situ neutron powder thermo‐diffraction experiments in the temperature range 300–1073 K. It was found that the crystallization takes place in a two‐step process, involving firstly the appearance of metastable Fe and Fe2Zr crystalline phases between 880 K and 980 K, and a subsequent polymorphic transformation into Fe3Zr above 980 K. These findings explain the anomalous magnetization vs. temperature behaviour on heating–cooling cycles.
Light‐induced degradation of charge carrier lifetime was observed in indium‐doped silicon. After defect formation, an annealing step at 200 °C for 10 min deactivates the defect and the initial charge carrier lifetime is fully recovered. The observed time range of the defect kinetics is similar to the well known defect kinetics of the light‐induced degradation in boron‐doped samples. Differences between defect formation in boron‐ and indium‐doped silicon are detected and discussed. A new model based on an acceptor self‐interstitial ASi–Sii defect is proposed and established with experimental findings and existing ab‐initio simulations.
In this Letter, a novel modified anodization was utilized to synthesize high‐aspect‐ratio, top‐open and ultraflat‐surface TiO2 nanotubes. The interruption of voltage during anodization leads to the formation of a double‐layered structure. Due to the weak mechanical connection between the upper and the underlying layer, the two parts can be easily detached. Compared with the conventional ultrasonication method to remove the clusters of nanotubes where rough surfaces resulted, this efficient and reliable strategy may facilitate further applications of TiO2 nanotubes in diverse conditions.
