Improved performance of silicon‐nanoparticle film‐coated dye‐sensitized solar cells

Silicon (Si) nanoparticles with average size of 13 nm and orange–red luminescence under UV absorption were synthesized using electrochemical etching of silicon wafers. A film of Si nanoparticles with thickness of 0.75 µm to 2.6 µm was coated on the glass (TiO₂ side) of a dye‐sensitized solar cell (DSSC). The cell exhibited nearly 9% enhancement in power conversion efficiency (η) at film thickness of ～2.4 µm under solar irradiation of 100 mW/cm² (AM 1.5) with improved fill factor and short‐circuit current density. This study revealed for the first time that the Si‐nanoparticle film converting UV into visible light and helping in homogeneous irradiation, can be utilized for improving the efficiency of the DSSCs. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High‐order Stokes and anti‐Stokes Raman generation in monoisotopic CVD 12C‐diamond

We determined, for the first time, the room temperature phonon energy related to the F_2g vibration mode (ω_SRS(12C) ～ 1333.2 cm^–1) in a mono‐crystalline single‐isotope CVD ¹²C‐diamond crystal by means of stimulated Raman scattering (SRS) spectroscopy. Picosecond one‐micron excitation using a Nd³⁺:Y₃Al₅O₁₂‐laser generates a nearly two‐octave spanning SRS frequency comb (～12000 cm^–1) consisting of higher‐order Stokes and anti‐Stokes components. The spacing of the spectral lines was found to differ by Δω_SRS ～ 0.9 cm^–1 from the comb spacing (ω_SRS(natC) ～ 1332.3 cm^–1) when pumping a conventional CVD diamond crystal with a natural composition of the two stable carbon isotopes ¹²C (98.93%) and ¹³C (1.07%). (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

High‐gain Zn1–xMgx O‐based ultraviolet photodetectors on Al2O3 and LiGaO2 substrates

We report the fabrication and characterization of highly responsive ZnMgO‐based ultraviolet (UV) photodetectors in the metal–semiconductor–metal (MSM) configuration for solar‐blind/visible‐blind optoelectronic application. MSM devices were fabricated from wurtzite Zn_1–xMg_x O/ZnO (x ～ 0.44) thin‐film heterostructures grown on sapphire (α‐Al₂O₃) substrates and w‐Zn_1–xMg_x O (x ～ 0.08), grown on nearly lattice‐matched lithium gallate (LiGaO₂) substrates, both by radio‐frequency plasma‐assisted molecular beam epitaxy (PAMBE). Thin film properties were studied by AFM, XRD, and optical transmission spectra, while MSM device performance was analyzed by spectral photoresponse and current–voltage techniques. Under biased conditions, α‐Al₂O₃ grown devices exhibit peak responsivity of ～7.6 A/W at 280 nm while LiGaO₂ grown samples demonstrate peak performance of ～119.3 A/W, albeit in the UV‐A regime (～324 nm). High photoconductive gains (76, 525) and spectral rejection ratios (～10³, ～10⁴) were obtained for devices grown on α‐Al₂O₃ and LiGaO₂, respectively. Exemplary device performance was ascribed to high material quality and in the case of lattice‐matched LiGaO₂ films, decreased photocarrier trapping probability, presumably due to low‐density of dislocation defects. To the best of our knowledge, these results represent the highest performing ZnO‐based photodetectors on LiGaO₂ yet fabricated, and demonstrate both the feasibility and substantial enhancement of photodetector device performance via growth on lattice‐matched substrates. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Thin film optimization design of organic–inorganic hybrids for waveguide high‐rejection optical filters

We report the fabrication of transparent, low surface roughness (<0.1 nm), and low‐loss (1.5 ± 0.2 dB cm^–1, 532 nm) thin films of organic–inorganic hybrids with controlled refractive index values stable under aging. High‐rejection optical filters based on first‐order Bragg gratings inscribed in channel waveguides were fabricated using UV‐laser writing. Their high‐rejection figure of merit (～24 dB) is the best value found until now for organic–inorganic hybrids reinforcing the potential of sol–gel technology in the integration of optoelectronic components based on hybrid materials, namely in the fabrication of cost‐effective integrated optics devices. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ultra‐thin (002)‐oriented Al‐doped zinc oxide transparent electrode grown on oxygen‐controlled homo‐seed layer

Highly (002)‐oriented Al‐doped zinc oxide (AZO) thin films with the thickness of less than 200 nm have been deposited on an oxygen‐controlled homo‐seed layer at 200 °C by DC magnetron sputtering. With the homo‐seed layer being employed, the full‐width at half maximum (FWHM) of the (002) diffraction peak for the AZO ultra‐thin films decreased from 0.33° to 0.22°, and, the corresponding average grain size increased from 26.8 nm to 43.0 nm. The XRD rocking curves revealed that the AZO ultra‐thin film grown on the seed layer deposited in atmosphere of O₂/Ar of 0.09 exhibited the most excellent structural order. The AZO ultra‐thin film with homo‐seed layer reached a resistivity of 4.2 × 10^–4 Ω cm, carrier concentration of 5.2 × 10²⁰ cm^–3 and mobility of 28.8 cm² V^–1 s^–1. The average transmittance of the AZO ultra‐thin film with homo‐seed layer reached 85.4% in the range of 380–780 nm including the substrate. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electroluminescence enhancement in ultraviolet organic light‐emitting diode with graded hole‐injection and ‐transporting structure

Electroluminescent intensity and external quantum efficiency (EQE) in ultraviolet organic light‐emitting diodes (UV OLEDs) have been remarkably enhanced by using a graded hole‐injection and ‐transporting (HIT) structure of MoO₃/N,N ′‐bis(naphthalen‐1‐yl)‐N,N ′‐bis(phenyl)‐benzidine/MoO₃/4,4′‐bis(carbazol‐9‐yl)biphenyl (CBP). The graded‐HIT based UV OLED shows superior short‐wavelength emis‐ sion with spectral peak of ～410 nm, maximum electroluminescent intensity of 2.2 mW/cm² at 215 mA/cm² and an EQE of 0.72% at 5.5 mA/cm². Impedance spectroscopy is employed to clarify the enhanced hole‐injection and ‐transporting capacity of the graded‐HIT structure. Our results provide a simple and effective approach for constructing efficient UV OLEDs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

All‐optical modulation based on silicon quantum dot doped SiOx:Si‐QD waveguide

All‐optical modulation based on silicon quantum dot doped SiO_x:Si‐QD waveguide is demonstrated. By shrinking the Si‐QD size from 4.3 nm to 1.7 nm in SiO_x matrix (SiO_x:Si‐QD) waveguide, the free‐carrier absorption (FCA) cross section of the Si‐QD is decreased to 8 × 10⁻¹⁸ cm² by enlarging the electron/hole effective masses, which shortens the PL and Auger lifetime to 83 ns and 16.5 ps, respectively. The FCA loss is conversely increased from 0.03 cm⁻¹ to 1.5 cm⁻¹ with the Si‐QD size enlarged from 1.7 nm to 4.3 nm due to the enhanced FCA cross section and the increased free‐carrier density in large Si‐QDs. Both the FCA and free‐carrier relaxation processes of Si‐QDs are shortened as the radiative recombination rate is enlarged by electron–hole momentum overlapping under strong quantum confinement effect. The all‐optical return‐to‐zero on‐off keying (RZ‐OOK) modulation is performed by using the SiO_x:Si‐QD waveguides, providing the transmission bit rate of the inversed RZ‐OOK data stream conversion from 0.2 to 2 Mbit/s by shrinking the Si‐QD size from 4.3 to 1.7 nm.     

Photoelectrochemical properties of texture‐controlled nanostructured α‐Fe2O3 thin films prepared by AACVD

Nanostructured α‐Fe₂O₃ thin film electrodes were deposited by aerosol‐assisted chemical vapour deposition (AACVD) for photoelectrochemical (PEC) water splitting on conducting glass substrates using 0.1 M methanolic solution of Fe(acac)₃. The XRD analysis confirmed that the films are highly crystalline α‐Fe₂O₃ and free from other iron oxide phases. The highly reproducible electrodes have an optical bandgap of ～2.15 eV and exhibit anodic photocurrent. The current–voltage characterization of the electrodes reveals that the photocurrent density strongly depended on the film morphology and deposition temperature. Scanning electron microscopy (SEM) analysis showed a change in the surface morphology with the change in deposition temperature. The films deposited at 450 °C have nanoporous structures which provide a maximum electrode/electrolyte interface. The maximum photocurrent density of 455 µA/cm² was achieved at 0.25 V vs. Ag/AgCl/3M KCl (～1.23 V vs. RHE) and the incident photon to electron conversion efficiency (IPCE) was 23.6% at 350 nm for the electrode deposited at 450 °C. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Tunable n‐ and p‐type doping of single‐layer graphene by engineering its interaction with the SiO2 support

We report a technique to tune the excess charge concentration in single‐layer graphene from p‐ to n‐type up to densities of |n | ～ 1.2 × 10¹³ cm^–2, corresponding to a displacement electric field of ～2.5 V/nm. The tuning is achieved by engineering the interaction between graphene and the underlying Si/SiO₂ substrate with an amino group‐terminated self‐assembled monolayer, and subsequent rinsing in aqueous solutions at controlled pH. Raman spectroscopy and electrical measurements on treated graphene devices confirm the occurrence of doping. Interestingly, we found the field‐effect mobility not to be significantly affected by the procedure. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Light Trapping and Down‐Shifting Effect of Periodically Nanopatterned Si‐Quantum‐Dot‐Based Structures for Enhanced Photovoltaic Properties

Periodically nanopatterned Si structures have been prepared by using a nanosphere lithography technique. The formed nanopatterned structures exhibit good anti‐reflection and enhanced optical absorption characteristics. The mean surface reflectance weighted by AM1.5 solar spectrum (300–1200 nm) is as low as 5%. By depositing Si quantum dot/SiO₂ multilayers (MLs) on the nanopatterned Si substrate, the optical absorption is higher than 90%, which is significantly improved compared with the same multilayers deposited on flat Si substrate. Furthermore, the prototype n‐Si/Si quantum dot/SiO₂ MLs/p‐Si heterojunction solar cells has been fabricated, and it is found that the external quantum efficiency is obviously enhanced for nanopatterned cell in a wide spectral range compared with the flat cell. The corresponding short‐circuit current density is increased from 25.5 mA cm^?2 for flat cell to 29.0 mA cm^?2 for nano‐patterned one. The improvement of cell performance can be attributed both to the reduced light loss and the down‐shifting effect of Si quantum dots/SiO₂ MLs by forming periodically nanopatterned structures.     

Vibrational Raman spectra of CdSx Se1‐x magic‐size nanocrystals

Resonant Raman scattering spectra of ultrasmall (<2 nm) magic‐size nanocrystals (NCs) are reported. The spectra of CdS and CdS_x Se_1‐x NCs, resonantly excited with 325 nm and 442 nm laser lines, correspondingly, reveal broad features in the range of bulk optical phonons. The relatively large width, ～50 cm^‐1, and downward shift, ～20 cm^‐1, of the Raman bands with respect to the longitudinal optical phonon in bulk crystals and large NCs are discussed based on the breaking of the translational symmetry and bond distortion in these ultrasmall NCs. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Trapped charge‐induced pyroelectric‐like transient response in single high‐resistivity Sb2Se3 nanowires

Dynamic scanning photocurrent microscopy was applied to Sb₂Se₃ crystalline single nanowires (NWs) to analyze their transient photocurrent responses. These NWs exhibited switching behavior with rapid rise and decay times upon illumination by laser pulses. The estimated spectral responsivity and external quantum efficiency for a freshly‐prepared NW at a bias voltage of 0.3 V and excitation wavelength of 488 nm were ～16.9 mA/W and ～42.9%, respectively. A pyroelectric‐like current transient was observed with reduced spectral responsivity when nonpolar Sb₂Se₃ single‐crystalline NWs were excited by laser pulses. Because Sb₂Se₃ NWs were nonpyroelectric or ferroelectric, the pyroelectric‐like current could possibly be attributed to temperature dependent nonlinear space‐charge distributions. Defects produced by the external electrical bias generated and re‐distributed space charges in the NWs. As a result, the temperature dependent inhomogeneous electric field led to nonlinear expansions or contractions of the lattice (electrostriction) that can produce pyroelectric current. We obtained a lower bound of equivalent pyroelectric coefficient α ≥ 60.09 μC/m² K from these materials by fitting the electrical transients. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Continuous-wave passively mode-locked Nd:YVO<Subscript>4</Subscript>/KTP green laser with a semiconductor saturable absorber mirror

A diode-pumped passively mode-locked low-doped Nd:YVO₄ green laser with a semiconductor saturable absorber mirror (SESAM) and an intracavity frequency-doubling KTP crystal is demonstrated. In order to efficiently release the thermal effect, a low-doped Nd:YVO₄ crystal with the Nd³⁺ concentration of 0.1 at % is employed as the gain medium. The maximum average output power of 3.1 W at 532 nm with a repetition rate of 102 MHz is obtained under the pump power of 25 W, corresponding to an optical conversion efficiency of 12.4%. The 532 nm mode locked pulse width is estimated to be approximately 6.1 ps.     

Efficient sub-nanosecond intracavity optical parametric oscillator pumped with a passively Q-switched Nd:GdVO<Subscript>4</Subscript> laser

An efficient diode-pumped passively Q-switched Nd:GdVO₄/Cr⁴⁺:YAG laser was employed to generate a high-repetition-rate, high-peak-power eye-safe laser beam with an intracavity optical parametric oscillator (OPO) based on a KTP crystal. The conversion efficiency for the average power is 8.3% from pump diode input to OPO signal output and the slope efficiency is up to 10%. At an incident pump power of 14.5 W, the compact intracavity OPO cavity, operating at 46 kHz, produces average powers at 1571 nm up to 1.2 W with a pulse width as short as 700 ps. PACS 42.60.Gd; 42.65.Yj; 42.55.X     

High‐Responsivity Photodetectors Based on Formamidinium Lead Halide Perovskite Quantum Dot–Graphene Hybrid

Highly performance photodetector requires a wide range of responses of the incident photons and converts them to electrical signals efficiently. Here, a photodetector based on formamidinium lead halide perovskite quantum dots (e.g., FAPbBr₃ QDs)–graphene hybrid, aiming to take the both advantages of the two constituents. The FAPbBr₃ QD–graphene layer not only benefits from the high mobility and wide spectral absorption of the graphene material but also from the long charge carrier lifetime and low dark carrier concentration of the FAPbBr₃ QDs. The photodetector based on FAPbBr₃ QD–graphene hybrid exhibits a broad spectral photoresponse ranging from 405 to 980 nm. A photoresponsivity of 1.15 × 10⁵AW⁻¹ and an external quantum efficiency as high as 3.42 × 10⁷% are obtained under an illumination power of 3 µW at 520 nm wavelength. In detail, a high responsivity is achieved in 405–538 nm, while a relatively low but fast response is observed in 538–980 nm. The photoelectric conversion mechanism of this hybrid photodetector is investigated in the view of built‐in electric field from the QD–graphene contact which improves the photoconductive gain.     

Au/TiO2 nanorod‐based Schottky‐type UV photodetectors

TiO₂ nanorods (NRs) were synthesized on fluorine‐doped tin oxide (FTO) pre‐coated glass substrates using hydrothermal growth technique. Scanning electron microscopy studies have revealed the formation of vertically‐aligned TiO₂ NRs with length of ～2 µm and diameter of 110–128 nm, homogenously distributed over the substrate surface. 130 nm thick Au contacts using thermal evaporation were deposited on the n‐type TiO₂ NRs at room temperature for the fabrication of NR‐based Schottky‐type UV photodetectors. The fabricated Schottky devices functioned as highly sensitive UV photodetectors with a peak responsivity of 134.8 A/W (λ = 350 nm) measured under 3 V reverse bias. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical management in high‐efficiency thin‐film silicon micromorph solar cells with a silicon oxide based intermediate reflector

In the effort to increase the stable efficiency of thin film silicon micromorph solar cells, a silicon oxide based intermediate reflector (SOIR) layer is deposited in situ between the component cells of the tandem device. The effectiveness of the SOIR layer in increasing the photo‐carrier generation in the a‐Si:H top absorber is compared for p–i–n devices deposited on different rough, highly transparent, front ZnO layers. High haze and low doping level for the front ZnO strongly enhance the current density (J_sc) in the μc‐Si:H bottom cell whereas J_sc in the top cell is influenced by the angular distribution of the transmitted light and by the reflectivity of the SOIR related to different surface roughness. A total J_sc of 26.8 mA/cm² and an initial conversion efficiency of 12.6% are achieved for 1.2 cm² cells with top and bottom cell thicknesses of 300 nm and 3 μm, and without any anti‐reflective coating on the glass. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

19.4%‐efficient large‐area fully screen‐printed silicon solar cells

We demonstrate industrially feasible large‐area solar cells with passivated homogeneous emitter and rear achieving energy conversion efficiencies of up to 19.4% on 125 × 125 mm² p‐type 2–3 Ω cm boron‐doped Czochralski silicon wafers. Front and rear metal contacts are fabricated by screen‐printing of silver and aluminum paste and firing in a conventional belt furnace. We implement two different dielectric rear surface passivation stacks: (i) a thermally grown silicon dioxide/silicon nitride stack and (ii) an atomic‐layer‐deposited aluminum oxide/silicon nitride stack. The dielectrics at the rear result in a decreased surface recombination velocity of S_rear = 70 cm/s and 80 cm/s, and an increased internal IR reflectance of up to 91% corresponding to an improved J_sc of up to 38.9 mA/cm² and V_oc of up to 664 mV. We observe an increase in cell efficiency of 0.8% absolute for the cells compared to 18.6% efficient reference solar cells featuring a full‐area aluminum back surface field. To our knowledge, the energy conversion efficiency of 19.4% is the best value reported so far for large area screen‐printed solar cells. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A Facile Method for Synthesis of Porous NiCo2O4 Nanorods as a High‐Performance Anode Material for Li‐Ion Batteries

Porous electrode materials with large specific surface area, relatively short diffusion path, and higher electrical conductivity, which display both better rate capabilities and good cycle lives, have huge benefits for practical applications in lithium‐ion batteries. Here, uniform porous NiCo₂O₄ nanorods (PNNs) with pore‐size distribution in the range of 10–30 nm and lengths of up to several micrometers are synthesized through a convenient oxalate co‐precipitation method followed by a calcining process. The PNN electrode exhibits high reversible capacity and outstanding cycling stability (after 150 cycles still maintain about 650 mA h g^?1 at a current density of 100 mA g^?1), as well as high Coulombic efficiency (>98%). Moreover, the PNNs also exhibit an excellent rate performance, and deliver a stable reversible specific capacity of 450 mA h g^?1 even at 2000 mA g^?1. These results demonstrate that the PNNs are promising anode materials for high‐performance Li‐ion batteries.     

Drop‐cast and dye‐sensitized ZnO nanorod‐based visible‐light photodetectors

We report the facile fabrication of metal–semiconductor–metal (MSM) photodetectors with dye‐sensitized ZnO nanorods (NRs) operating at wavelengths of ～405–638 nm by a simple drop casting method. The ZnO NRs were synthesized by the hydrothermal synthesis method at 75 °C. The droplet of ethanol solution containing ZnO NRs was dropped between two metal electrodes and dried at 65 °C, which allows the ZnO NRs to be adhered and contacted to both metal electrodes. When a violet light of 405 nm was illuminated into the MSM ZnO NRs‐based photodetector, the photocurrent gain was obtained as ～3.9 × 10³ at the applied bias voltage of 5 V. By increasing the bias voltage from 10 V to 15 V, the device exhibited good recovery performance with a largely reduced reset time from 85.68 s to 2.47 s and an increased on–off ratio from 17.9 to 77.4. To extend the photodetection range towards the long visible spectral region, the ZnO NRs were sensitized by the N719 dye and then drop‐cast. The dye‐sensitized ZnO NRs‐based photodetector also exhibited good photocurrent switching under 638 nm of light illumination. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)