SP–PLP–EPR Investigations into the Chain‐Length‐Dependent Termination of Methyl Methacrylate Bulk Polymerization

Termination kinetics of methyl methacrylate (MMA) bulk polymerization has been studied via the single pulsed laser polymerization–electron paramagnetic resonance method. MMA‐d₈ has been investigated to enhance the signal‐to‐noise quality of microsecond time‐resolved measurement of radical concentration. Chain‐length‐dependent termination rate coefficients of radicals of identical size, k, are reported for 5–70 °C and up to i = 100. k decreases according to the power‐law expression . At 5 °C, k_t for two MMA radicals of chain‐length unity is k = (5.8 ± 1.3) · 10⁸ L · mol⁻¹ · s⁻¹. The associated activation energy and power‐law exponent are: E_A(k) ≈ 9 ± 2 kJ · mol⁻¹ and α ≈ 0.63 ± 0.15, respectively.

     

Novel acyclic nitroxides for nitroxide‐mediated polymerization: Kinetic,electron paramagnetic resonance spectroscopic,X‐ray diffraction,and molecular modeling investigations

This work describes the synthesis of new hydrophobic acyclic nitroxides [derived from 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐nitroxide (TIPNO)] designed to be employed in radical miniemulsion polymerization. We present the synthetic strategies employed to obtain these different nitroxides and the determination of certain important parameters, such as the dissociation rate constant, the combination rate constant, and the decomposition rate constant, of the corresponding alkoxyamines. All these new nitroxides give good control of the bulk radical polymerization of styrene in comparison with the parent TIPNO. The molecular structure of some nitroxides presented herein has been elucidated by single‐crystal X‐ray diffraction, and their structural determination helps us to understand better the influence of the nitroxide structure on the activation energy. A molecular modeling study has also been conducted on these new nitroxides, and a good linear correlation between the activation energy and the CNC bond angle for a series of nitroxides with the same type of leaving radical has been found. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1926–1940, 2006     

SP‐PLP‐EPR—A Novel Method for Detailed Studies into the Termination Kinetics of Radical Polymerization

Single pulse–pulsed laser polymerization–electron paramagnetic resonance (SP‐PLP‐EPR) has been introduced as a powerful method for the very detailed analysis of termination kinetics. During polymerization an intense laser pulse is applied in order to almost instantaneously produce a burst of radicals. The decay of radical concentration is measured by highly time‐resolved EPR and is analyzed with respect to the rate coefficients for the termination of two radicals of identical size. SP‐PLP‐EPR experiments have been carried out for an itaconate monomer, for several methacrylates in bulk and in a solution of ionic liquids, for methacrylic acid in aqueous solution, and for the solution polymerization of butyl acrylate in toluene at low temperature. The data fully support the composite model, which assumes a stronger chain‐length dependence of termination for radicals of smaller size and a weaker one for large radicals. The SP‐PLP‐EPR technique is also applicable in systems with more than one type of growing radicals, as is the case with butyl acrylate polymerization at higher temperature and with RAFT polymerizations, where the novel method may be used for a comprehensive kinetic analysis.

     

Free‐Radical Termination Kinetics Studied Using a Novel SP‐PLP‐ESR Technique

Summary: A novel method for measuring termination rate coefficients, k_t, in free‐radical polymerization is presented. A single laser pulse is used to instantaneously produce photoinitiator‐derived radicals. During subsequent polymerization, radical concentration is monitored by time‐resolved electron spin resonance (ESR) spectroscopy. The size of the free radicals, which exhibits a narrow distribution increases linearly with time t, which allows the chain‐length dependence of k_t to be deduced. The method will be illustrated using dodecyl methacrylate polymerization as an example.

Two straight lines provide a very satisfactory representation of the chain‐length dependence of k_t over the entire chain‐length region (c_R = radical concentration).     

SET‐LRP of methyl acrylate to complete conversion with zero termination

The single electron transfer‐living radical polymerization of methyl acrylate (MA) initiated by bis(2‐bromopropionyl)ethane (BPE) in dimethyl sulfoxide was carried out to 100% monomer conversion and complete absence of bimolecular termination under the following reaction conditions: [MA]/[BPE]/[Me₆‐TREN]/[CuBr₂] = 60/1/0.21/0.01 and [MA]/[BPE]/[TREN]/[CuBr₂] = 60/1/0.25/0.05. These polymerizations were mediated by 0.5 cm of hydrazine‐activated Cu(0) wire of 20 gauge (0.812 cm in diameter), corresponding to a surface area of 0.14 cm² of Cu(0) per 3 mL reaction volume (2/1 v/v monomer/solvent). A higher extent of bimolecular termination (5–13%) was observed at complete conversion when longer lengths of Cu(0) wire were used. In the absence of CuBr₂ the activated Cu(0) wire/Me₆‐TREN catalyst in dimethyl sulfoxide also allowed the synthesis of perfectly bifunctional and monofunctional PMAs at complete conversion. This was also demonstrated by the quantitative reinitiation experiments from the chain(s) end(s) of these macroinitiators. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of well‐defined macromonomers and comb copolymers from polymers made by atom transfer radical polymerization

Poly(n‐butyl acrylate) macromonomers with predetermined molecular weights (1300 < number‐average molecular weight < 23,000) and low polydispersity indices (<1.2) were synthesized from bromine‐terminated atom transfer radical polymerization polymers via end‐group substitution with acrylic acid and methacrylic acid. These macromonomers, having a high degree of end‐group functionalization (>90%), were radically homopolymerized to obtain comb polymers. A high macromonomer concentration, combined with a low radical flux, was needed to obtain a high conversion of the macromonomers and a reasonable degree of polymerization. By the traditional radical copolymerization of the hydrophobic macromonomers with the hydrophilic monomer N,N‐dimethylaminoethyl methacrylate (DMAEMA), amphiphilic comb copolymers were obtained. The conversions of the macromonomers and comonomer were almost quantitative under optimized reaction conditions. The molecular weights were high (number‐average molecular weight ≈70,000), and the molecular weight distribution was broad (polydispersity index ≈ 3.5). Kinetic measurements showed simultaneous decreases in the macromonomer and DMAEMA concentrations, indicating a relatively homogeneous composition of the comb copolymers over the whole molecular weight range. This was supported by preparative size exclusion chromatography. The copolymerization of poly(n‐butyl acrylate) macromonomers with other hydrophilic monomers such as acrylic acid or N,N‐dimethylacrylamide gave comb copolymers with multimodal molecular weight distributions in size exclusion chromatography and extremely high apparent molecular weights. Dynamic light scattering showed a heterogeneous composition consisting of small (6–9 nm) and large (23–143 nm) particles, probably micelles or other type of aggregates. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3425–3439, 2003     

Atom transfer radical polymerization of n‐butyl acrylate catalyzed by CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine

The homogeneous atom transfer radical polymerization (ATRP) of n‐butyl acrylate with CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine as a catalyst and ethyl 2‐bromoisobutyrate as an initiator was investigated. The kinetic plots of ln([M]₀/[M]) versus the reaction time for the ATRP systems in different solvents such as toluene, anisole, N,N‐dimethylformamide, and 1‐butanol were linear throughout the reactions, and the experimental molecular weights increased linearly with increasing monomer conversion and were very close to the theoretical values. These, together with the relatively narrow molecular weight distributions (polydispersity index ～ 1.40 in most cases with monomer conversion > 50%), indicated that the polymerization was living and controlled. Toluene appeared to be the best solvent for the studied ATRP system in terms of the polymerization rate and molecular weight distribution among the solvents used. The polymerization showed zero order with respect to both the initiator and the catalyst, probably because of the presence of a self‐regulation process at the beginning of the reaction. The reaction temperature had a positive effect on the polymerization rate, and the optimum reaction temperature was found to be 100 °C. An apparent enthalpy of activation of 81.2 kJ/mol was determined for the ATRP of n‐butyl acrylate, corresponding to an enthalpy of equilibrium of 63.6 kJ/mol. An apparent enthalpy of activation of 52.8 kJ/mol was also obtained for the ATRP of methyl methacrylate under similar reaction conditions. Moreover, the CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine‐based system was proven to be applicable to living block copolymerization and living random copolymerization of n‐butyl acrylate with methyl methacrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3549–3561, 2002     

Kinetics and electron spin resonance study of the radical polymerization of n‐butyl acrylate mediated by a nitroxide precursor: C‐phenyl‐N‐tert‐butylnitrone

The C‐phenyl‐N‐tert‐butylnitrone/azobisisobutyronitrile pair is able to impart control to the radical polymerization of n‐butyl acrylate as long as a two‐step process is implemented, that is, the prereaction of the nitrone and the initiator in toluene at 85 °C for 4 h followed by the addition and polymerization of n‐butyl acrylate at 110 °C. The structure of the in situ formed nitroxide has been established from kinetic and electron spin resonance data. The key parameters (the dissociation rate constant, combination rate constant, and equilibrium constant) that govern the process have been evaluated. The equilibrium constant between the dormant and active species is close to 1.6 × 10^?12 mol L^?1 at 110 °C. The dissociation rate constant and the activation energy for the C? ON bond homolysis are 1.9 × 10^?3 s^?1 and 122 ± 15 kJ mol^?1, respectively. The rate constant of recombination between the propagating radical and the nitroxide is as high as 1.2 × 10⁹ L mol^?1 s^?1. Finally, well‐defined poly(n‐butyl acrylate)‐b‐polystyrene block copolymers have been successfully prepared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6299–6311, 2006     

Reaction kinetics and gel effect on the polymerization of 2‐ethoxyethyl methacrylate and 2(2‐ethoxyethoxy) ethyl methacrylate

Polymerization kinetics at several temperatures of 2‐ethoxyethyl methacrylate (EEMA) and 2(2‐ethoxyethoxy) ethyl methacrylate (DEMA) in bulk and in dioxane solutions are described. The gel effect was never detected at monomer concentrations equal to or lower than 1 mol L^?1, although in the bulk polymerization both monomers display the gel effect at very low conversions. Because of the influence of the efficiency factor f on the polymerization rate, a theoretical kinetic interpretation of the changes in f with monomer and initiator concentrations and kinetic parameters was performed to achieve a better understanding of the mechanisms involved in radical polymerization. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3987–4001, 2002     

Controlled radical polymerization of styrene mediated by the C‐phenyl‐N‐tert‐butylnitrone/AIBN pair: Kinetics and electron spin resonance analysis

Kinetics of the free radical polymerization of styrene at 110 °C has been investigated in the presence of C‐phenyl‐N‐tert‐butylnitrone (PBN) and 2,2′‐azobis(isobutyronitrile) (AIBN) after prereaction in toluene at 85 °C. The effect of the prereaction time and the PBN/AIBN molar ratio on the in situ formation of nitroxides and alkoxyamines (at 85 °C), and ultimately on the control of the styrene polymerization at 110 °C, has been investigated. As a rule, the styrene radical polymerization is controlled, and the mechanism is one of the classical nitroxide‐mediated polymerization. Only one type of nitroxide (low‐molecular‐mass nitroxide) is formed whatever the prereaction conditions at 85 °C, and the equilibrium constant (K) between active and dormant species is 8.7 × 10^?10 mol L^?1 at 110 °C. At this temperature, the dissociation rate constant (k_d) is 3.7 × 10^?3 s^?1, the recombination rate constant (k_c) is 4.3 × 10⁶ L mol^?1 s^?1, whereas the activation energy (E_a,diss.), for the dissociation of the alkoxyamine at the chain‐end is ～125 kJ mol^?1. Importantly, the propagation rate at 110 °C, which does not change significantly with the prereaction time and the PBN/AIBN molar ratio at 85 °C, is higher than that for the thermal polymerization at 110 °C. This propagation rate directly depends on the equilibrium constant K and on the alkoxyamine and nitroxide concentrations, as well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1219–1235, 2007     

Single‐electron transfer‐living radical copolymerization of butyl methacrylate and divinylbenzene for preparation of oil‐absorbing gel

Crosslinking copolymerization of butyl methacrylate with a small amount of divinylbenzene (DVB) was carried out using single‐electron transfer‐living radical polymerization initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/N‐ligand in N,N‐dimethylformamide to produce a highly oil‐absorbing gel. The polymerization, gelation process, and oil‐absorbing properties were studied in detail. Analysis of monomer conversion with reaction time showed that the polymerization followed first‐order kinetics for both linear and crosslinking polymerization before gelation. Higher levels of DVB led to earlier gelation and the influence of N‐ligand on gelation was also significant. Under optimal conditions, oil absorption of the prepared gel to chloroform could reach 42.1 g·g^?1. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3233–3239     

Improving the initiation efficiency in the single electron transfer living radical polymerization of methyl acrylate with electronic chain‐end mimics

Computational studies on the heterolytic bond dissociation energies and electron affinities of methyl 2‐bromopropionate (MBP) and ethyl 2‐bromoisobutyrate (EBiB) in the dissociative electron transfer (DET) step of single electron transfer living radical polymerization (SET‐LRP) of methyl acrylate (MA) combined with kinetic experiments were performed in an effort to design the most efficient initiation system. This study suggests that EBiB is more effective than MBP in the SET‐LRP of acrylates catalyzed by Cu(0) wire, thus being a true electronic mimic of the dormant PMA species. EBiB allows for a more predictable dependence of the molecular weight evolution and distribution. This is exemplified by the absence of a deviation in the PMA molecular weight from theoretical values at low conversions, as a result of a faster SET activation with EBiB than with MBP. The enhanced control over molecular weight evolution was also observed in the SET‐LRP of MA initiated with bifunctional initiators similar in structure to MBP and EBiB, suggesting a higher reactivity than MBP in the SET activation, which matches closely that of the polymer dormant chains. The use of bifunctional initiators in conjunction with activated Cu(0) wire in SET‐LRP allows for dramatically accelerated polymerizations, although still providing for exceptional control of the molecular weight evolution and distribution. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Influence of the isomeric structures of butyl acrylate on its single‐electron transfer‐degenerative chain transfer living radical polymerization in water Catalyzed by Na2S2O4

The aim of this work is to the study the influence of the isomer structures of butyl acrylate monomer on the single‐electron transfer/degenerative chain transfer mediated living radical polymerization (SET‐DTLRP). The kinetic of isobutyl acrylate is determined for the first time by SET‐DTLRP in water catalyzed by sodium dithionite. The plots of number‐average molecular weight versus conversion and ln([M]₀/[M]) versus time are linear, demonstrating a controlled polymerization. The influence of the isomer t‐butyl, i‐butyl, and n‐butyl on the kinetics, properties, and stereochemistry of the reactions was assessed. To the best of our knowledge, there is no previous report dealing with the synthesis of PiBA by any LRP approach in aqueous medium. The results presented in this work suggest that the stability provided by the acrylate side group has an important influence in the polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6542–6551, 2008     

Average termination rate coefficients in emulsion polymerization: Effect of compartmentalization on free‐radical lifetimes

A method is presented by which the time‐dependent average termination rate coefficient in an emulsion polymerization may be calculated as an appropriate average of the chain‐length‐dependent termination rate coefficients. The method takes advantage of the fact that the overall termination rate is dominated by terminations between rapidly moving short radicals and much slower long ones. This termination rate coefficient is suitable for use in the Smith–Ewart equations describing the compartmentalization of radicals in an emulsion polymerization. Rate data in emulsion polymerizations can be quantitatively interpreted if the kinetics fall into one of two categories: zero–one (showing compartmentalization; intraparticle termination is not rate‐determining) or pseudo‐bulk (no compartmentalization; intraparticle termination is rate‐determining). The new method can be used to interpret rate data for systems falling between these categories and also can be used to find termination rate coefficients from Monte Carlo simulations of termination kinetics. The latter is especially useful for predicting and understanding kinetics in controlled radical polymerizations in disperse media. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1076–1089, 2005     

Free‐radical copolymerization of styrene with butyl acrylate. II. Elemental kinetic copolymerization step predictions from homopolymerization data

The free‐radical copolymerization of styrene and butyl acrylate has been carried out in benzene at 50 °C. The lumped k _p/k parameter (where k _p and k _t are the average copolymerization propagation and termination rate constants, respectively) has been determined. Applying the implicit penultimate unit model for the overall copolymerization propagation rate coefficient and the terminal unit effect for the overall copolymerization termination rate coefficient and using the homopolymerization kinetic coefficients, we have found good qualitative agreement between the experimental and theoretical k _p/k values. The variation of the copolymerization rate in solution with respect to the values previously found in bulk has been ascribed to a chain length effect on the copolymerization termination rate coefficient. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 130–136, 2004     

Studying the Fundamentals of Radical Polymerization Using ESR in Combination with Controlled Radical Polymerization Methods

Electron spin resonance (ESR) spectroscopy can contribute to understanding both the kinetics and mechanism of radical polymerizations. A series of oligo/poly(meth)acrylates were prepared by atom transfer radical polymerization (ATRP) and purified to provide well defined radical precursors. Model radicals, with given chain lengths, were generated by reaction of the terminal halogens with an organotin compound and the radicals were observed by ESR spectroscopy. This combination of ESR with ATRPs ability to prepare well defined radical precursors provided significant new information on the properties of radicals in radical polymerizations. ESR spectra of the model radicals generated from tert-butyl methacrylate precursors, with various chain lengths, showed clear chain length dependent changes and a possibility of differentiating between the chain lengths of observed propagating radicals by ESR. The ESR spectrum of each dimeric, trimeric, tetrameric, and pentameric tert-butyl acrylate model radicals, observed at various temperatures, provided clear experimental evidence of a 1,5-hydrogen shift.     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Poly(methyl methacrylate‐co‐pentaerythritol tetraacrylate‐co‐butyl methacrylate)‐g‐polystyrene: Synthesis and high oil‐absorption property

Well‐defined high oil‐absorption resin was successfully prepared via living radical polymerization on surface of polystyrene resin‐supported N‐chlorosulfonamide group utilizing methyl methacrylate and butyl methacrylate as monomers, ferric trichloride/iminodiacetic acid (FeCl₃/IDA) as catalyst system, pentaerythritol tetraacrylate as crosslinker, and L ‐ascorbic acid as reducing agent. The polymerization proceeded in a “living” polymerization manner as indicated by linearity kinetic plot of the polymerization. Effects of crosslinker, catalyst, macroinitiator, reducing agent on polymerization and absorption property were discussed in detail. The chemical structure of sorbent was determined by FTIR spectrometry. The oil‐absorption resin shows a toluene absorption capacity of 21 g g^?1. The adsorption of oil behaves as pseudo‐first‐order kinetic model rather than pseudo‐second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Propagation rate coefficients of isobornyl acrylate,tert‐butyl acrylate and 1‐ethoxyethyl acrylate: A high frequency PLP‐SEC study

Pulsed laser polymerization (PLP) coupled to size exclusion chromatography (SEC) is considered to be the most accurate and reliable technique for the determination of absolute propagation rate coefficients, k_p. Herein, k_p data as a function of temperature were determined via PLP‐SEC for three acrylate monomers that are of particular synthetic interest (e.g., for the generation of amphiphilic block copolymers). The high‐T_g monomer isobornyl acrylate (iBoA) as well as the precursor monomers for the synthesis of hydrophilic poly(acrylic acid), tert‐butyl acrylate (tBuA), and 1‐ethoxyethyl acrylate (EEA) were investigated with respect to their propagation rate coefficient in a wide temperature range. By application of a 500 Hz laser repetition rate, data could be obtained up to a temperature of 80 °C. To arrive at absolute values for k_p, the Mark‐Houwink parameters of the polymers have been determined via on‐line light scattering and viscosimetry measurements. These read: K = 5.00 × 10⁵ dL g⁻¹, a = 0.75 (piBoA), K = 19.7 × 10⁵ dL g⁻¹, a = 0.66 (ptBA) and K = 1.53 × 10⁵ dL g⁻¹, a = 0.85 (pEEA). The bulky iBoA monomer shows the lowest propagation rate coefficient among the three monomers, while EEA is the fastest. The activation energies and Arrhenius factors read: (iBoA): log(A/L mol⁻¹ s⁻¹) = 7.05 and E_A = 17.0 kJ mol⁻¹; (tBuA): log(A/L mol⁻¹ s⁻¹) = 7.28 and E_A = 17.5 kJ mol⁻¹ and (EEA): log(A/L mol⁻¹ s⁻¹) = 6.80 and E_A = 13.8 kJ mol⁻¹. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6641–6654, 2009