Palladium-citric acid-ammonium fluoride as a matrix modifier for overcoming of interferences occurring during the direct determination of Sn in aqua regia extracts from environmental samples by D2-ETAAS

When tin is to be determined in such a complex matrix like aqua regia extracts of environmental samples by electrothermal atomic absorption spectrometry (ETAAS), spectral interferences occur when deuterium-lamp (D₂) background correction is used, even using high pyrolysis temperature of 1400 °C achieved with palladium with citric acid chemical modifier. We have found that the further addition of NH₄F to palladium with citric acid chemical modifier is essential for overcoming the above-mentioned problems for which aluminium oxide is most probably responsible. It is supposed, that NH₄F enables volatilization of the alumina matrix formed by hydrolysis from the chloride salt and interfering in a gas phase via the formation of AlF₃ which could be, in contrast to aluminium oxide, removed from the graphite furnace during the pyrolysis stage. Using the proposed chemical modifier, the direct and accurate determination of Sn in aqua regia extracts from rocks, soils and sediments is possible even when using matrix free standard solutions. This presumption was confirmed by the analysis of certified reference samples and by the comparison with inductively coupled plasma time of flight mass spectrometry (ICP-TOFMS) method. Characteristic mass and LOD value for the original sample (10-μL aliquots of sample) was 17 pg and 0.055 μg g⁻¹, respectively.     

Molybdenum, Mo-Ir and Mo-Ru coatings as permanent chemical modifiers for the determination of cadmium and lead in sediments and soil samples by electrothermal atomic absorption spectrometry

Molybdenum, Ir, Ru, Mo-Ir, Mo-Ru thermally coated on to platforms inserted in pyrolytic graphite tubes as permanent modifiers and Pd + Mg(NO₃)₂ conventional modifier mixture have been employed for the determination of cadmium and lead in dissolved sediments and soil samples by electrothermal atomic absorption spectrometry (ETAAS). Optimum masses and mass ratios of permanent modifiers for the analysis of Cd and Pb in sample solutions have been investigated. The 280 μg of Mo, 200 μg of Ir, 200 μg of Ru, 280 μg of Mo + 200 μg of Ir or 280 μg of Mo + 200 μg of Ru has been found as efficient as 5 μg of Pd + 3 μg of Mg(NO₃)₂ for increasing thermal stabilization of analytes and for decreasing the most serious interferences. Pyrolysis and atomization temperatures, atomization and background signal shapes, characteristic masses and detection limits of analytes in dissolved samples with or without permanent and conventional modifiers have been compared. The detection limits and characteristic masses obtained with Mo-Ir coated platform are 0.01 μg g⁻¹ and 1.1 pg for Cd and 0.09 μg g⁻¹ and 19 pg for Pb, respectively. Long-term stabilities for analytes in samples with Mo, Mo-Ir, Mo-Ru and Pd + Mg(NO₃)₂ have been studied. Cadmium and lead contents have been determined in certified and standard reference materials by using optimum conditions investigated and the results obtained with Mo-Ir or Mo-Ru were in agreement with the values of certified reference materials.     

Determination of traces of Ni in Li(2)CO(3)/Na(2)CO(3) melts by graphite furnace atomic absorption spectrometry

A graphite furnace atomic absorption method is described for the determination of traces of Ni in 52 mole percent (mol.%) Li₂CO₃ and 48 mol.% Na₂CO₃ melts after dissolution of the sample in dilute nitric acid. Maximum pyrolysis and optimum atomisation temperatures for the analyte were determined in the presence of the Li and Na matrix constituents. Pre-pyrolysed ascorbic acid (typical amount of 5 μg) has been used as chemical modifier for effectively suppressing the chemical and spectral interferences of the Li/Na matrix, thus that the analysis can be conducted using acid-matched standard solutions. The results of the Ni analysis in synthetic sample solutions by calibration graph against acid-matched standards well agree with those obtained by the method of standard additions. Recoveries ranged from 99 to 101% and the relative standard deviation is around 3% at the 20 μg L⁻¹ level. Moreover, the use of the chemical modifier leads to an improvement of the lifetime of the graphite tube. The Ni detection limit (3σ) in Li/Na carbonate melts for the proposed method is similar to that obtained in aqueous solution, i.e. 5 × 10⁻⁸ g analyte per gram of (Li_0.52Na_0.48) ₂CO₃ melt. This method is successfully applied to the determination of nickel in real carbonate melt samples.     

Evaluation of V, Ir, Ru, V-Ir, V-Ru, and W-V as permanent chemical modifiers for the determination of cadmium, lead, and zinc in botanic and biological slurries by electrothermal atomic absorption spectrometry

Permanent modifiers (V, Ir, Ru, V-Ir, V-Ru, and W-V) thermally coated on to platforms of pyrolytic graphite tubes were employed for the determination of Cd, Pb, and Zn in botanic and biological slurries by electrothermal atomic absorption spectrometry (ETAAS). Conventional Pd + Mg(NO₃)₂ modifier mixture was also used for the determination of analytes in slurries and digested samples. Optimum masses and mass ratios of permanent modifiers for Cd, Pb, and Zn in slurry sample solutions were investigated. The 280 μg of V, 280 μg of V + 200 μg of Ir, 280 μg of V + 200 μg of Ru or 240 μg of W + 280 μg of V in 0.2% (v/v) Triton X-100 plus 0.5% (v/v) HNO₃ mixture was found as efficient as 5 μg of Pd + 3 μg of Mg(NO₃)₂ modifier mixture for obtaining thermal stabilization, and for obtaining best recoveries. Optimization conditions of analytes, such as pyrolysis and atomization temperature, characteristic masses and detection limits, and atomization and background peak profiles were studied with permanent and 5 μg of Pd + 3 μg of Mg(NO₃)₂ conventional modifiers and compared with each other. The permanent V-Ir, V-Ru, and W-V modifiers remained stable for approximately 250-300 firings when 20 μl of slurries and digested samples were delivered into the atomizer. In addition, the mixed permanent modifiers increase the tube lifetime by 50-95% when compared with untreated platforms. The characteristic masses and detection limits of analytes (dilution factor of 125 ml g⁻¹) obtained with V-Ir based on integrated absorbance as example for 0.8% (m/v) slurries were 1.0 pg and 3 ng g⁻¹ for Cd, 18 pg and 17 ng g⁻¹ for Pb, and 0.7 pg and 4 ng g⁻¹ for Zn, respectively. The results of analytes obtained by employing V-Ir, V-Ru, and W-V permanent modifier mixtures in botanic and biological certified and standard reference materials were in agreement with the certified values of reference materials.     

Interference-free determination of thallium in aqua regia leaches from rocks, soils and sediments by D(2)-ETAAS method using mixed palladium-citric acid-lithium chemical modifier

The mixture of palladium (chloride) with citric acid and lithium is proposed as a new chemical modifier for the elimination of interference occurred during the determination of Tl in aqua regia extracts from rocks, soils and sediments by electrothermal atomic absorption spectrometry using instrumentation with deuterium-lamp background correction (D₂-ETAAS). Palladium was preferred to rhodium and platinum as to analyte stabilization, citric acid served as an effective reducing agent facilitating formation of Pd-Tl stable covalent bonds playing an important role in the analyte stabilization. Citric acid in addition helps to remove most of interfering chloride at low temperature. The further addition of Li increased significantly the robustness of chemical modifier against strongly interfering ZnCl₂ matrix by binding free chlorine into a more stable LiCl molecule. In the presence of the proposed chemical modifier the temperature for the final step of pyrolysis was adjustable up to 1000 °C, without any noticeable loss of volatile Tl species and the interference of the rest chloride matrix was significantly reduced. The application of the modifier to direct determination of Tl in aqua regia extracts from rocks, soils and sediments has ensured the characteristic mass and LOD value for the original sample 13 pg and 0.043 μg g⁻¹, respectively (10-μL aliquots of sample) and has enabled the use of matrix-free standard solutions for attaining accurate analysis. The accuracy was verified by the analysis of certified reference samples and by the comparison of results with those found by an inductively coupled plasma orthogonal acceleration time-of-flight mass spectrometer (ICP-oa-TOFMS) method.     

On-line elimination of spectral interference of iron matrix in the flame atomic absorption determination of zinc by anion-exchange separation

A flow injection analysis (FIA) system has been developed for the flame atomic absorption spectroscopic (FAAS) determination of zinc in iron matrix. The spectral line interference of iron at 213.859 nm was eliminated by on-line separation using a micro-column of strong anion-exchange resin (Dowex 1-X8). The zinc chloro complexes were retained from 2 M HCl solution while most of the iron chloro complexes were passed to waste. For a 2% iron solution, matrix removal efficiency was 98.2% which means that positive spectral line interference of iron at the Zn line was reduced from 0.42 to 0.008 μg ml⁻¹ Zn. The optimized flow injection system can handle up to 48 samples with good precision (less than 3.5% relative standard deviation (R.S.D.)) in the working range of 0.075-2.2 μg ml⁻¹ Zn. Comparative analysis of a certified reference material and synthetic sample solutions containing traces of Zn in 2% Fe by the proposed method and by graphite furnace atomic absorption spectroscopy (GFAAS) showed no evidence of analytical bias at the 95% confidence level.     

Study on the simultaneous determination of some essential and toxic trace elements in honey by multi-element graphite furnace atomic absorption spectrometry

A multi-element graphite furnace atomic absorption spectrometry (GFAAS) method was elaborated and applied for the simultaneous determination of As, Cd, Cr, Cu, and Pb in various kinds of honey samples (acacia, floral, linden, rape, and milkweed) using the transversally heated graphite atomiser (THGA) with end-capped tubes and integrated graphite platforms (IGPs). For comparative GFAAS analysis, direct (without digestion) and indirect (with digestion in a microwave oven) sample preparation procedures were tested. The effects of several chemical modifiers, such as NH₄H₂PO₄, NH₄H₂PO₄-Mg(NO₃)₂, and Pd(NO₃)₂-Mg(NO₃)₂, were studied to obtain optimal pyrolysis and atomization conditions for the set of analytes studied. The most efficient modifier was proved to be the mixture of 5 μg Pd (applied as nitrate) plus 3 μg Mg(NO₃)₂, allowing the optimal 600 °C pyrolysis and 2300 °C atomization temperatures. To prevent the sputtering and foaming of the matrix during the drying and pyrolysis steps of the furnace heating program, the sample and modifier solutions (20 + 5 μl, respectively) were dispensed together onto the IGP of the THGA pre-heated at 80 °C.The effect of increasing concentration of honey matrix was studied on the integrated absorbance (A_int) signals of analytes. The A_int signals of Cr and Pb were not altered up to 10% (m/v) matrix content in the sample solutions. The matrix effect was slightly suppressive on the A_int signals of As, Cd, and Cu above 2% (m/v) honey concentration. The recovery was found to be ranged between 85 and 115% for Cd, Cr, Cu, and Pb, whereas it was a lower, compromise value of 70-99% for As. The limit of detection (LOD) data were 1, 0.04, 0.09, 0.3, and 0.6 μg l⁻¹ for As, Cd, Cr, Cu, and Pb, respectively, which values correspond to 20, 0.8, 1.8, 5.3, and 12 ng g⁻¹, respectively, in the solid samples. The characteristic masses were found to be 21 pg As, 1.3 pg Cd, 4 pg Cr, 12 pg Cu, and 33 pg Pb. The As, Cd, Cr, Cu, and Pb contents of the studied 42 honey samples varied significantly, i.e. from below the LOD up to 13, 3.3, 109, 445, and 163 ng g⁻¹, respectively.     

A chemiluminescence sensor for the determination of hydrogen peroxide

A chemiluminescence one-shot sensor for hydrogen peroxide is described. It is prepared by immobilization of cobalt chloride and sodium lauryl sulphate in hydroxyethyl cellulose matrix cast on a microscope cover glass. Luminol, sodium phosphate and the sample are mixed before use and applied on the membrane by a micropipette. The calibration graph is linear in the range 20-1600 μg/L, and the detection limit of the method (3σ) is 9 μg/L. A relative standard deviation of 4.5% was obtained for 100 μg/L H₂O₂ (n = 11). The sensor has been applied successfully to the determination of hydrogen peroxide in rainwater.     

A comparative study of chemical modifiers in the determination of total arsenic in marine food by tungsten coil electrothermal atomic absorption spectrometry

Three platinum group elements (Pd, Ir and Rh) both in solution and in pre-reduced form, and also combined with Mg(NO₃)₂ or ascorbic acid, were assessed as possible chemical modifiers on the atomization of As in digest solutions of seafood matrices (clam and fish tissue) by tungsten coil electrothermal atomic absorption spectrometry (TCA-AAS) and compared without a modifier. Of 28 modifier alternatives in study including single form and binary mixtures, and based on maximum pyrolysis temperature without significant As loss and best As absorbance sensitivity during atomization, three modifiers: Rh (0.5 μg), Ir (1.0 μg) and Rh (0.5 μg) + ascorbic acid (0.5 μg), at optimum amounts were pre-selected and compared. The definitive modifier (rhodium (0.5 μg)) was selected by variance analysis. The mean within-day repeatability was 3% in consecutive measurements (25-300 μg l⁻¹) (three cycles, each of n = 6) and showed good short-term stability of the absorbance measurements. The mean reproducibility was 4% (n = 18 in a 3-day period) and the detection limit (3σ_blank/slope) was 42 pg (n = 16). Quantitation was by standard additions to compensate for matrix effects not corrected by the modifier. Three sample digestion procedures were compared in fish and clam tissue samples: microwave acid digestion alone (A) or combined with the addition of 2% (m/v) K₂S₂O₈ solution followed either by UV photo-oxidation (B) or re-digestion in a thermal block (C). The accuracy was established by determination of As in certified reference material of dogfish muscle (DORM-2). Procedures B and C showed good recoveries (102% (n = 4) and 103% (n = 7), respectively), whereas procedure A was not quantitative (85%). The methodology is simple, fast, reliable, of low cost and was applied to the determination of total As in lyophilized samples of clam and fish collected in the Chilean coast.     

Direct determination of P in biodiesel by high-resolution continuum source graphite furnace atomic absorption spectrometry

The direct determination of P in biodiesel by high-resolution continuum source graphite furnace atomic absorption spectrometry has been investigated. A slow drying stage proved to be essential for good repeatability. Optimization was performed by a D optimal planning. The atomization temperature and modifier composition were the most relevant parameters. Thus, using a mixture of Pd (30 μg) and Mg(NO₃)₂ (20 μg) as the modifier, previously deposited onto the platform of the graphite tube and dried, a five step drying stage, and pyrolysis and atomization temperatures of 1000 and 2700 °C, respectively, a limit of detection of 0.5 μg g^− 1 was obtained. The analysis of biodiesel of different origins confirmed that external calibration with organic P standard solutions, diluted in P-free biodiesel, could be used. In this way, excellent agreement between the found and expected results was observed in the analysis of an ANP interlaboratorial exercise sample.     

New method for speciation analysis of aluminium fluoride complexes by HPLC-FAAS hyphenated technique

Speciation analysis of aluminium in the presented system of HPLC-FAAS hyphenated technique lasts 4 min. Using the bifunctional column in model analysis and using the calculation methods for modelling using the Mineql program enabled the authors to presume that particular forms will be subjected to elution in the following order: (1) AlF₂⁺ and AlF₄⁻, (2) AlF²⁺ and AlF₃⁰ and (3) Al³⁺. Based on the obtained results for model solutions, the presented method enables the determination of aluminium fluoride complexes and Al³⁺ speciation form. The study compares the tendency of occurrence variability of aluminium fluoride complexes and Al³⁺ form, determined based on the results obtained using the HPLC-FAAS hyphenated technique with the trend defined based on the Mineql program calculation method. The method was successfully applied to soil samples.     

The problem of arsenic interference in the analysis of Cd to evaluate its extractability in soils contaminated by arsenic

The arsenic (As) spectral interference observed in the determination of cadmium (Cd) by inductively coupled plasma atomic emission spectrometry (ICP-AES) was studied in atomic absorption spectrometry (AAS) using flame (FAAS) and graphite furnace (GFAAS) as atomizers. The soils of 15 kitchen gardens located near two smelters in the North of France were selected according the ratio As/Cd. Four different extracting solutions usually used to evaluate the mobility of Cd were chosen to extract Cd from these soil samples: citric acid 0.11 M, acetic acid 0.11 M, calcium chloride 0.01 M and water. The quantitative determinations of Cd in the 15 soils for each solvent were investigated by ICP-AES at two lines (228.802 and 214.438 nm) and by FAAS or GFAAS with two-way background compensation. Compared to the Cd concentrations measured in the acid solutions and in the CaCl₂ solution after the addition of a chemical modifier, it was clearly demonstrated that the high-speed self-reversal background compensation (HSSR-method) was the method of choice to eliminate the spectral interference of As during Cd determination by FAAS and by GFAAS. In water, it was shown that the deuterium lamp used for the background compensation (D₂-method) was able to eliminate the most of the As interference. In comparison with Cd concentrations in water after adding a chemical modifier, those obtained with the HSSR-method were similar and a very good correlation was obtained between these two methods (R² = 0.995). It was therefore established that the HSSR-method would be able to replace the chemical modifiers to eliminate As interference in the determination of Cd-extractable from As contaminated soils.     

Feasibility of using in situ fusion for the determination of Co,Cr and Mn in Portland cement by direct solid sampling graphite furnace atomic absorption spectrometry

In situ fusion on the boat-type graphite platform has been used as a sample pretreatment for the direct determination of Co, Cr and Mn in Portland cement by solid sampling graphite furnace atomic absorption spectrometry (SS-GF AAS). The 3-field Zeeman technique was adopted for background correction to decrease the sensitivity during measurements. This strategy allowed working with up to 200 µg of sample. The in situ fusion was accomplished using 10 µL of a flux mixture 4.0% m/v Na₂CO₃ + 4.0% m/v ZnO + 0.1% m/v Triton® X-100 added over the cement sample and heated at 800 °C for 20 s. The resulting mould was completely dissolved with 10 µL of 0.1% m/v HNO₃. Limits of detection were 0.11 µg g^− 1 for Co, 1.1 µg g^− 1 for Cr and 1.9 µg g^− 1 for Mn. The accuracy of the proposed method has been evaluated by the analysis of certified reference materials. The values found presented no statistically significant differences compared to the certified values (Student's t-test, p < 0.05). In general, the relative standard deviation was lower than 12% (n = 5).     

Improvement of direct determination of Cu and Mn in seawater by GFAAS and total elimination of the saline matrix with the use of hydrofluoric acid

Hydrofluoric acid, added to seawater, can assist in the removal of chloride in the drying step by precipitating fluoride salts, thus suppressing the chloride interference effects induced on the atomization signals of Cu and Mn. By adding HF to seawater before the analysis, MgF₂ and CaF₂ are precipitated at the bottom of the sampling flask, without precipitating Cu and Mn, and are consequently not introduced into the graphite furnace. Because sodium salts are eliminated at the pretreatment step, the whole seawater matrix is eliminated before the atomization of Cu or Mn. Therefore, the analyzed volume of seawater can be increased by using the multi-injection procedure without degradation of the limit of detection and risks of spectral interferences. The limit of detection obtained for Cu and Mn are 0.05 and 0.01 μg L⁻¹, respectively, for a 50 μL analyzed seawater volume.     

A study of the direct determination of Cd, Cr, Cu, Pb and Zn in certified reference materials of soils by solid sampling electrothermal atomic absorption spectrometry

A simple and rapid method for the direct determination of Cd, Cr, Cu, Pb and Zn in soil was developed. The method was developed using three certified reference materials of soil: Eutric Cambisol, Orthic Luvisols and Rendzina, which differed in their matrix composition. Chemical modifiers were essential to achieve reproducible and interference-free signals for the analytes studied. The best results were obtained with a Pd/Mg(NO₃)₂ admixture for the determination of Cd, Pb and Zn and NH₄F for Cu. The combination of W (as a permanent modifier) and Mg(NO₃)₂ provided well-defined signal profiles for Cr. The following spectral lines were used: Cd 228.8 nm, Cr 520.6 nm, Cu 218.2 nm, Pb 205.3 nm and Zn 307.6 nm. The limit of detection was 4.2 ng g^− 1 for Cd, 1.1 μg g^− 1 for Cr, 0.5 μg g^− 1 for Cu, 1.3 μg g^− 1 for Pb and 8.6 μg g^− 1 for Zn for the maximum sample mass used. Under optimized conditions, the analyte and matrix were separated effectively in situ, and aqueous standards could be used for calibration.     

Fluoride matrix modifiers for the determination of aluminum by graphite furnace atomic absorption spectrometry

A method was tested for the determination of aluminum by graphite furnance atomic absorption spectrometry using hydrofluoric acid and cesium fluoride as matrix modifiers. Alunimum trifluoride is stable to 1291°C, after which it sublimes to form AlF₃ gas. The subsequent gas-phase atomization of AlF₃ occurs rapidly, and produces clean, sharp absorption peaks. This method has a detection limit of 7 pg Al at a confidence interval of 95%. The method is fairly insensitive to interferences, with the exception of strongly complexing organic acids. The addition of CuF₂ to the matrix appears to eliminate interference from organic acids, but was found to produce a high background absorbance and to shorten the life of the graphite tube.     

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG)₂ complex was eluted with 1 mol l⁻¹ HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml⁻¹ Na⁺, K⁺, Mg²⁺, Al³⁺ and Fe³⁺; 5000 μg ml⁻¹ Ca²⁺ ; 500 μg ml⁻¹ Pb²⁺; 125 μg ml⁻¹ Zn²⁺; 50 μg ml⁻¹ Cu²⁺ and 25 μg ml⁻¹ Ni²⁺ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l⁻¹, respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg⁻¹ and 4.06 mg g⁻¹, respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples.     

A method for Ca, Fe, Ga, Na, Si and Zn determination in alumina by inductively coupled plasma optical emission spectrometry after aluminum precipitation

In this present work a method for the determination of Ca, Fe, Ga, Na, Si and Zn in alumina (Al₂O₃) by inductively coupled plasma optical emission spectrometry (ICP OES) with axial viewing is presented. Preliminary studies revealed intense aluminum spectral interference over the majority of elements and reaction between aluminum and quartz to form aluminosilicate, reducing drastically the lifetime of the torch. To overcome these problems alumina samples (250 mg) were dissolved with 5 mL HCl + 1.5 mL H₂SO₄ + 1.5 mL H₂O in a microwave oven. After complete dissolution the volume was completed to 20 mL and aluminum was precipitated as Al(OH)₃ with NH₃ (by bubbling NH₃ into the solution up to a pH ~ 8, for 10 min). The use of internal standards (Fe/Be, Ga/Dy, Zn/In and Na/Sc) was essential to obtain precise and accurate results. The reliability of the proposed method was checked by analysis of alumina certified reference material (Alumina Reduction Grade-699, NIST). The found concentrations (0.037% w w⁻¹ CaO, 0.013% w w⁻¹ Fe₂O₃, 0.012% w w⁻¹ Ga₂O₃, 0.49% w w⁻¹ Na₂O, 0.014% w w⁻¹ SiO₂ and 0.013% w w⁻¹ ZnO) presented no statistical differences compared to the certified values at a 95% confidence level.     

Feasibility of internal standardization in the direct and simultaneous determination of As, Cu and Pb in sugar-cane spirits by graphite furnace atomic absorption spectrometry

Bismuth and Sb were evaluated as internal standards (IS) to minimize matrix effects on the direct and simultaneous determination of As, Cu, and Pb in cachaça by graphite furnace atomic absorption spectrometry using W-coated platform plus Pd-Mg(NO₃)₂ as modifier. For 20 μL injected sample, calibration within the 0.5-10 μg L⁻¹ As, 100-1000 μg L⁻¹ Cu and 0.5-30 μg L⁻¹ Pb intervals were established using the ratios As absorbance to Sb absorbance, Cu absorbance to Bi absorbance and Pb absorbance to Bi absorbance versus analytes concentration, respectively. Typical linear correlations of 0.998, 0.999 and 0.999 were, respectively, obtained. The proposed method was applied for direct determination of As, Cu and Pb in 10 commercial cachaça samples and results were in agreement with those obtained by inductively coupled plasma mass spectrometry at 95% confidence level. The found characteristic masses were 30 pg As, 274 pg Cu and 39 pg Pb. The useful lifetime of the graphite tube was around 760 firings. Recoveries of As, Cu and Pb added to cachaça samples varied, respectively, from 98% to 109%, 97% to 108% and 98% to 104% with internal standards and from 48% to 54%, 53% to 92% and 62% to 97% without internal standards. The limits of detection were 0.13 μg L⁻¹ As, 22 μg L⁻¹ Cu and 0.05 μg L⁻¹ Pb. The relative standard deviations (n = 12) for a spiked sample containing 20 μg L⁻¹ As, Pb and 500 μg L⁻¹ Cu were 1.6%, 1.0%, and 1.8% with IS and 4.3%, 5.2%, and 5.5% without IS.     

Ammonium fluoride as a novel chemical modifier for the elimination of magnesium chloride interference on the determination of lead by graphite furnace atomic absorption spectrometry

Ammonium fluoride was found to be very efficient modifier for the elimination of MgCl₂ interference on Pb determination. Ammonium fluoride probably converts strongly interfering volatile MgCl₂ to less volatile MgF₂ matrix that makes possible the release of Pb analyte at lower temperature, before the matrix starts to vaporize. It was observed likewise that NH₄F removes the interferences mentioned, i.e. caused by MgCl₂ presence, much more effectively as compared with some modifiers, before now recommended for this purpose. The application of this modifier to the determination of Pb in 2% (m/v) MgCl₂ has ensured the characteristic mass and LOD value in the original sample of 12 pg and 60 ng g⁻¹, respectively (10 μl aliquots of sample). Applying the modifier to standards and samples enables the use of matrix-free standard solutions for attaining accurate analysis as verified by recovery studies.