Evolution of structural features and mechanical properties during the conversion of poly[(methylamino)borazine] fibers into boron nitride fibers

Poly[(methylamino)borazine] (PolyMAB) green fibers of a mean diameter of 15 μm have been pyrolyzed under ammonia up to 1000°C and heat treated under nitrogen up to 2000°C to prepare boron nitride (BN) fibers. During the polymer-to-ceramic conversion, the mechanical properties of the green fibers increase within the 25-400°C temperature range owing to the formation of a preceramic material and remain almost constant up to 1000°C. Both the crystallinity and the mechanical properties slightly increase within the 1000-1400°C range, in association with the consolidation of the fused-B₃N₃ basal planes. A rapid increase in tensile strength (σ^R) and elastic modulus (Young's modulus E) is observed in relation with crystallization of the BN phase for fibers treated between 1400°C and 1800°C. At 2000°C, “meso-hexagonal” BN fibers of 7.5 μm in diameter are finally obtained, displaying values of σ^R=1.480 GPa and E=365 GPa. The obtention of both high mechanical properties and fine diameter for the as-prepared BN fibers is a consequence of the stretching of the green fibers on a spool which is used during their conversion into ceramic.     

The use of silver nanoparticles as an effective modifier for the determination of arsenic and antimony by electrothermal atomic absorption spectrometry

Silver nanoparticles (AgNPs) were proposed as a new chemical modifier for the elimination of interferences when determining arsenic and antimony in aqueous NaCl or Na₂SO₄ solutions and in sea-water by electrothermal atomic absorption spectrometry. For this purpose, the AgNPs were prepared simply by reducing silver nitrate with sodium citrate. The effects of pyrolysis and atomization temperatures and the amounts of interferents and modifiers on the sensitivities of these elements were investigated. In the presence of the proposed modifier, a pyrolysis temperature of at least 1100 °C for arsenic and 900 °C for antimony could be applied without the loss of analytes, and the interferences were greatly reduced to allow for interference-free determination. The detection limits (N = 10, 3σ) for arsenic and antimony were 0.022 ng and 0.046 ng, respectively. AgNPs are cheaper and more available compared to many other modifiers. No background was detected, and the blank values were negligible.     

Growth and spectroscopic properties of Nd-doped Sr3Y2 (BO3)4 crystal

A new crystal of Nd³⁺:Sr₃Y₂ (BO₃)₄ with a dimension of Φ 15×30 mm³ was grown by the Czochralski method. The grown crystal was characterized using X-ray diffraction. The absorption and emission spectra of Nd³⁺:Sr₃Y₂ (BO₃)₄ were investigated. The absorption transition at 807 nm has an FWHM of 16 nm. The absorption and emission cross sections are 6.32×10⁻²⁰ cm² at 807 nm and 1.07×10⁻¹⁹ cm² at 1065 nm, respectively. The luminescence lifetime τ_f is 51.7 μs at room temperature.     

New members of ternary rare-earth metal boride carbides containing finite boron-carbon chains: RE25B14C26 (RE=Pr, Nd) and Nd25B12C28

New ternary rare-earth metal boride carbides RE₂₅B₁₄C₂₆ (RE=Pr, Nd) and Nd₂₅B₁₂C₂₈ were synthesized by co-melting the elements. Nd₂₅B₁₂C₂₈ is stable up to 1440 K. RE₂₅B₁₄C₂₆ (RE=Pr, Nd) exist above 1270 K. The crystal structures were investigated by means of single-crystal X-ray diffraction. Nd₂₅B₁₂C₂₈: space group P, a=8.3209(7) Å, b=8.3231(6) Å, c=29.888(2) Å, α=83.730(9)°, β=83.294(9)°, γ=89.764(9)°. Pr₂₅B₁₄C₂₆: space group P2₁/c, a=8.4243(5) Å, b=8.4095(6) Å, c=30.828(1) Å, β=105.879(4)°, V=2100.6(2) Å³, (R1=0.048 (wR2=0.088) from 2961 reflections with I_o>2σ(I_o)); for Nd₂₅B₁₄C₂₆ space group P2₁/c, Z=2, a=8.3404(6) Å, b=8.3096(6) Å, c=30.599(2) Å, β=106.065(1)°. Their structures consist of a three-dimensional framework of rare-earth metal atoms resulting from the stacking of slightly corrugated and distorted square nets, leading to cavities filled with cumulene-like molecules [B₂C₄]⁶⁻ and [B₃C₃]⁷⁻, nearly linear [BC₂]⁵⁻ and bent [BC₂]⁷⁻ units and isolated carbon atoms. Structural and theoretical analysis suggests the ionic formulation for RE₂₅B₁₄C₂₆: (RE³⁺)₂₅[B₂C₄]⁶⁻([B₃C₃]⁷⁻)₂([BC₂]⁵⁻)₄([BC₂]⁷⁻)₂(C⁴⁻)₄·5e⁻ and for Nd₂₅B₁₂C₂₈: (Nd³⁺)₂₅([B₂C₄]⁶⁻)₃([BC₂]⁵⁻)₄([BC₂]⁷⁻)₂(C⁴⁻)₄·7e⁻. Accordingly, extended Hückel tight-binding calculations indicate that the compounds are metallic in character.     

Bis(trifluoromethyl)dicarbonate, CF3OC(O)OC(O)OCF3

The synthesis of the new compound, bis(trifluoromethyl)dicarbonate, CF₃OC(O)OC(O)OCF₃, is carried out by reduction of bis(trifluoromethyl)trioxidicarbonate with excess of CO at 0 °C. The product is characterized by IR, Raman, ¹³C and ¹⁹F NMR spectroscopy and its properties are compared with those of the other members of the series CF₃OC(O)O_xC(O)OCF₃, x = 0-3. Single crystals are grown at −25 °C and the X-ray diffraction analysis shows the packing of syn-syn rotamers exhibiting C₂ symmetry. DFT calculations predict this rotamer as the most stable one and also structural and vibrational data are predicted reasonably well.     

La3TaO7 derivatives with Weberite structure type: Possible electrolytes for solid oxide fuel cells and high temperature electrolysers

In this study, with the aim to enhance the ionic conduction of known structures by defect chemistry, the La₂O₃-Ta₂O₅ system was considered with a focus on the La₃TaO₇ phase whose structure is of Weberite type. In order to predict possible preferential substitution sites and substitution elements, atomistic simulation was used as a first approach. A solid solution La_3−xSr_xTaO_7−x/2 was confirmed by X-ray diffraction and Raman spectroscopy; it extends for a substitution ratio up to x = 0.15. Whereas La₃TaO₇ is a poor oxide ion conductor (σ_700 °C = 2 × 10⁻⁵S.cm⁻¹), at 700 °C, its ionic conductivity is increased by more than one order of magnitude when 3.3% molar strontium is introduced in the structure (σ_700 °C = 2 × 10⁻⁴S.cm⁻¹).     

From unsaturated dodecahedranes to C40 cages?

(2+2)-Dimerization of unsaturated, highly pyramidalized dodecahedranes (Φ = 43-45°) is explored as a route to C₄₀-cage molecules and non-classical ions derived thereby. The cycloadducts (X-ray structure) formed under vigorous conditions either in solution or in the solid phase above 300 °C did not undergo 2σ → 2π isomerization. The MS fragmentation patterns, in line with calculations (B3LYP/6-31G*), suggest the formation of ‘open’ C₄₀ dications.     

Determination of cadmium and lead in cetacean Dolphinidae tissue from the coast of Bahia state in Brazil by GFAAS

In the present study, cadmium and lead in the muscle, lung, liver and kidney of dolphins (Sotalia guianensis and Stenella clymene) of the Bahia coast in the northwest of Brazil were determined by graphite furnace atomic absorption spectrometry. Samples were digested using a diluted oxidant mixture (HNO₃ + H₂O₂) with a microwave heating program performed in five steps. The optimized temperatures and chemical modifier for the pyrolysis and atomization were 700 °C, 1400 °C and Pd plus Mg for Cd, and 900 °C, 1800 °C and NH₄H₂PO₄ for Pb, respectively. Characteristic masses and limits of detections (n = 20, 3σ) for Cd and Pb were 1.6 and 9.0 pg and 0.82 ng g^− 1 and 0.50 ng g^− 1, respectively. Repeatability ranged from 0.87 to 8.22% for Cd and 4.31 to 8.09% for Pb. The found concentrations presented no statistical differences at the 95% confidence level when compared with the ICP OES methods. Addition and recovery tests were also performed and the results ranged between 87 and 112% for both elements. Samples of cetacean Dolphinidae (S.guianensis and S.clymene) were analyzed, and the higher concentrations ranged from 0.09 to 46.2 µg g^− 1 for Cd and 0.04 to 0.47 µg g^− 1 for Pb in liver, and from 0.133 to 277 µg g^− 1 for Cd in the kidney.     

Carbon nanotube—chalcogenide glass composite

This article describes the preparation of multi-walled carbon nanotube—chalcogenide glass composite by direct synthesis and the melt-quenching method. The carbon nanotubes—chalcogenide glass composite was characterized by high-resolution transmission electron microscopy (HRTEM), TEM/energy-dispersive X-ray spectroscopy, low energy electron excited X-ray spectroscopy, Raman spectroscopy, spectroscopic ellipsometry, microhardness, and impedance spectroscopy. CNTs-AgAsS₂ glass composite possess highly increased ionic conductivity, from σ_25 °C=4.38±0.0438×10⁻⁶ to σ_25 °C=6.57±0.0657×10⁻⁶ S cm⁻¹ and decreased refractive index from n=2.652 to 2.631 at the wavelength λ=1.55 μm.     

Highly phosphonated polypentafluorostyrene: Characterization and blends with polybenzimidazole

In this study we present results of the conductivity and resistance to thermooxidative and condensation reactions of a highly phosphonated poly(pentafluorostyrene) (PWN2010) and of its blends with poly(benzimidazole)s (PBI). This polymer, which combines both: (i) a high degree of phosphonation (above 90%) and (ii) a relatively high acidity (pK_a (–PO₃H₂ ↔ –PO₃H⁻) ∼ 0.5) due to the fluorine neighbors, is designed for low humidity operating fuel cell. This was confirmed by the conductivity measurements for PWN2010 reaching σ = 5 × 10⁻⁴ S cm⁻¹ at 150 °C in dry N₂ and σ = 1 × 10⁻³ S cm⁻¹ at 150 °C (λ = 0.75). Furthermore, this polymer showed only 48% of anhydride formation when annealing it at T = 250 °C for 5 h and only 2% weight loss during a 96 h Fenton test. These properties combined with the ability of the PWN2010 to form homogeneous blends with polybenzimidazoles resulting in stable and flexible polymer films, makes PWN2010 a very promising candidate as a polymer electrolyte for intermediate- and high-temperature fuel cell applications.     

Preconcentration and determination of ultra trace amounts of arsenic(III) and arsenic(V) in tap water and total arsenic in biological samples by cloud point extraction and electrothermal atomic absorption spectrometry

A new approach for developing a cloud point extraction-electrothermal atomic absorption spectrometry has been described and used for determination of arsenic. The method is based on phase separation phenomenon of non-ionic surfactants in aqueous solutions. After reaction of As(V) with molybdate towards a yellow heteropoly acid complex in sulfuric acid medium and increasing the temperature to 55 °C, analytes are quantitatively extracted to the non-ionic surfactant-rich phase (Triton X-114) after centrifugation.To decrease the viscosity of the extract and to allow its pipetting by the autosampler, 100 μl methanol was added to the surfactant-rich phase. An amount of 20 μl of this solution plus 10 μl of 0.1% m/v Pd(NO₃)₂ were injected into the graphite tube and the analyte determined by electrothermal atomic absorption spectrometry.Total inorganic arsenic(III, V) was extracted similarly after oxidation of As(III) to As(V) with KMnO₄. As(III) was calculated by difference. After optimization of the extraction condition and the instrumental parameters, a detection limit (3σ_B) of 0.01 μg l⁻¹ with enrichment factor of 52.5 was achieved for only 10 ml of sample. The analytical curve was linear in the concentration range of 0.02-0.35 μg l⁻¹. Relative standard deviations were lower than 5%. The method was successfully applied to the determination of As(III) and As(V) in tap water and total arsenic in biological samples (hair and nail).     

Electrical conductivity investigation of diluted potassium chloride solutions in binary mixture triethylamine-water near its consolute point

The binary liquid mixture of triethylamine + water (TEA-W) has a lower consolute point at a critical composition of 32.27 mass % triethylamine. Starting at a temperature within the one-phase region, the electrical conductivity of a sample of this mixture with addition of (K⁺, Cl⁻) ions was measured and found to be accurately described by the Vogel-Fulcher-Tammann (VFT) law. Before that, for the pure system, in a temperature range ΔT = T_c − T < 2 °C where T_c is the critical temperature, the electrical conductivity (σ) exhibits a monotonous deviation from the VFT behaviour. This anomaly is finite at T_c. The asymptotic behaviour of the electrical conductivity anomaly is described by a power law t^1−α, where t is the reduced temperature |(T−Tc)/Tc| and α is the critical exponent of the specific heat anomaly at constant pressure. For the electrolyte mixtures, by combining the viscosity and the electrical conductivity data, the value of the computed Walden product has been determined and the salt dissociation degrees as well as the Debye screening length have been estimated.     

Crystal structure and conductivity investigation of KDyP4O12: a new potassium dysprosium cyclotetraphosphate

A single-crystal X-ray diffraction analysis has been performed on KDyP₄O₁₂ synthesized by a flux method. The new compound crystallizes at room temperature in the monoclinic space group C2/c with unit cell parameters: a=7.812(2) Å, b=12.318(3) Å, c=10.441(2) Å, β=111.09(2)°, V=937.42(4) Å³ and D_cal=3.66 g cm⁻³ for Z=4. A full-matrix least square refinement gave R₁=0.022, wR₂=0.04 for 2421 independent reflections (I>2σ(I)) refined with 84 parameters.The structure is built up from P₄O₁₂⁴⁻ cyclotetraphosphate anions linked by DyO₈ polyhedra to form a three-dimensional framework, which delimits intersecting oxygen tunnels in which the K⁺ ions are located. The atomic arrangement can be described as a succession of layers extending along the [010] direction. The P₄O₁₂⁴⁻ ring anion is centrosymmetrical is connected by irregularly shaped KO₁₀ polyhedra to form a layer structure parallel to (001). Dysprosium and potassium are surrounded by eight and ten oxygen atoms respectively.Samples have been examined by impedance and infrared spectroscopy techniques. The reported IR absorption investigation, recorded at room temperature in the frequency range 200-4000 cm⁻¹, shows some bands characteristic of cyclotetraphosphates.The electrical conductivity of KDyP₄O₁₂ has subsequently been measured as a function of temperature, it represents a significant ionic conductivity and activation energy (σ=2.15×10⁻⁴ Ω⁻¹cm⁻¹ at 453 K and E_a=0.387 eV) corresponding to the mobility of the K⁺ cations located within tunnels.     

Bio-oil production from Onopordum acanthium L. by slow pyrolysis

In this study, the usability of the plant thistle, Onopordum acanthium L., belonging to the family Asteraceae (Compositae), in liquid fuel production has been investigated. The experiments were performed in a fixed-bed Heinze pyrolysis reactor to investigate the effects of heating rate, pyrolysis temperature and sepiolite percentage on the pyrolysis product yields and chemical compositions. Experiments were carried out in a static atmosphere with a heating rate of 7 °C/min and 40 °C/min, pyrolysis temperature of 350, 400, 500, 550 and 700 °C and particle size of 0.6 < D_p < 0.85 mm. Catalyst experiments were conducted in a static atmosphere with a heating rate of 40 °C/min, pyrolysis temperature of 550 °C and particle size of 0.6 < D_p < 0.85 mm. Bio-oil yield increased from 18.5% to 27.3% with the presence of 10% of sepiolite catalyst at pyrolysis temperature of 550 °C, with a heating rate of 40 °C/min, and particle size of 0.6 < D_p < 0.85 mm. It means that the yield of bio-oil was increased at around 48.0% after the catalyst added. Chromatographic and spectroscopic studies on the bio-oil showed that the oil obtained from O. acanthium L. could be used as a renewable fuels and chemical feedstock.     

Correction of structured molecular background by means of high-resolution continuum source electrothermal atomic absorption spectrometry—Determination of antimony in sediment reference materials using direct solid sampling

A simple, fast and accurate procedure is proposed for the determination of antimony in certified sediment reference materials using direct solid sampling high-resolution continuum source electrothermal atomic absorption spectrometry and iridium as a permanent modifier. The less sensitive resonance line at 231.147 nm has been used in order to allow the introduction of larger sample mass. Six certified reference materials, one river, one estuarine and four marine sediments have been analyzed. The use of iridium as a permanent modifier caused an increase of 30% in sensitivity and stabilized antimony in the sediment to a pyrolysis temperature of 1100 °C. Significant background absorption with pronounced rotational fine structure was observed at the optimum atomization temperature of 2100 °C, which coincided with the analyte atomic absorption in time. This background was found to be due to the electron excitation spectra of mostly the SiO and in part the PO molecules, and could be eliminated by applying a least-squares background correction algorithm. A characteristic mass of 28 pg Sb was obtained, and the limit of detection (3σ, n = 10) was 0.02 μg g⁻¹, calculated for 0.2 mg of sample. The results obtained for six certified reference materials with concentrations between 0.40 and 11.6 ± 2.6 μg g⁻¹ Sb were in agreement with the certified values according to a Student's t-test for a 95% confidence level, using aqueous standards for calibration. The precision, expressed as relative standard deviation, ranged between 7% and 17% (n = 5).     

Two-photon absorption chromophores with a tunable [2,2′]bithiophene core

Sonogashira coupling between 3,5,3′,5′-tetrabromo-[2,2′]bithiophene and various terminal alkynes provides two-photon absorption (TPA) chromophores 1-6, which possess electron donor (D) and/or acceptor (A) alkynyl substituents at 3(3′) and 5(5′) sites of the bithiophene core. The up-converted fluorescence emission excited at 800 nm (Ti:sapphire femtosecond laser, ∼100 fs pulses) was used to determine the two-photon absorption cross-sections (σ) of these compounds. The corresponding TPA cross-section (σ) values ranging from 132 to 1120 GM (10⁻⁵⁰ cm⁴ s photon⁻¹) can be fine-tuned by the substitutents. The quadrupolar-type (A-π-D-π-A) chromophore 5 exhibits the largest σ value (1120 GM) in CH₂Cl₂ upon 800 nm excitation.     

Growth and spectroscopic characterization of Nd:Sr6GdSc(BO3)6 crystal

A crystal of Nd³⁺:Sr₆GdSc(BO₃)₆ with the dimension of φ20×30 mm³ was grown by Czochralski method. The grown crystal was characterized by X-ray diffraction and DSC analysis. The DSC analysis showed that the crystal congruently melt at 1306.7°C. The absorption and emission spectra of Nd³⁺:Sr₆GdSc(BO₃)₆ were investigated. The absorption band at 806 nm has a FWHM of 13 nm. The absorption and emission cross-sections are 2.33×10⁻²⁰ cm² at 806 nm and 1.58×10⁻¹⁹ cm² at 1062 nm, respectively. The luminescence lifetime τ_f is 75 μs at room temperature.     

Measurement and modeling of osmotic coefficients of aqueous solution of ionic liquids using vapor pressure osmometry method

Osmotic coefficients of binary mixtures containing an ionic liquid, (1-butyl-3-methylimidazolium tetrafluoroborate, [BMIm]BF₄, 1-ethyl-3-methylimidazolium ethyl sulfate, [EMIm]ES, and 1-butyl-3-methylimidazolium methyl sulfate, [BMIm]MS) with water were measured until about 3 molal concentrations using vapor pressure osmometry method (VPO) at temperature ranges 298.15–328.15 K and modeled using different electrolyte excess Gibbs free energy models including electrolyte non-random two liquids (NRTL), modified NRTL (MNRTL), mean spherical approximation NRTL (MSA-NRTL), non random factor (NRF), and extended Wilson models. The results show that osmotic coefficient data increase with increasing temperature. The calculated standard deviations of the studied systems show that the applicability of these models for the correlation of VLE properties of ionic liquid solutions. The average standard deviations for the models have the order σ(?) MNRTL < σ(?) Wilson < σ(?) NRTL < σ(?) MSA-NRTL < σ(?)NRF. The results show MNRTL model is able to reproduce experimental osmotic coefficients of aqueous solution of studied ionic liquids with good precision.     

Temperature-dependent structural study of microporous CsAlSi5O12

CsAlSi₅O₁₂ crystals were synthesized at high temperature by slow cooling of a vanadium oxide flux. Single-crystal X-ray diffraction structure analysis and electron microprobe analyses yielded the microporous CAS zeolite framework structure of Cs_0.85Al_0.85Si_5.15O₁₂ composition. High-temperature single-crystal and powder X-ray diffraction studies were utilized to analyze anisotropic thermal expansion. Rietveld refined cell constants from powder diffraction data, measured in steps of 25 °C up to 700 °C, show a significant decrease in expansion above 500 °C. At 500 °C, a displacive, static disorder-dynamic disorder-type phase transition from the acentric low-temperature space group Ama2 to centrosymmetric Amam (Cmcm in standard setting) was found. Thermal expansion below the phase transition is governed by rigid-body TO₄ rotations accompanied by stretching of T-O-T angles. Above the phase transition at 500 °C all atoms, except one oxygen (O6), are fixed on mirror planes. Temperature-dependent polarized Raman single-crystal spectra between −270 and 300 °C and unpolarized spectra between room temperature and 1000 °C become increasingly less resolved with rising temperature confirming the disordered static-disordered dynamic type of the phase transition.