Thermal behavior of ammonium perchlorate and metal powders of different grades

The effects of aluminum (Al) and nickel (Ni) powders of various grain sizes on the thermal decomposition of ammonium perchlorate (AP) were investigated by TG and DSC in a dynamic nitrogen atmosphere. The TG results show that Al powders have no effect on the thermal decomposition of AP at conventional grain size, while the nanometer-sized Ni powders (n-Ni) have a great influence on the thermal decomposition of AP with conventional and superfine grain size. The results obtained by DSC and an in situ FTIR analysis of the solid residues confirmed the promoting effects of n-Ni. The effects of n-Ni have been ascribed to its enhancement on the gas phase reactions during the second step decomposition of conventional grain size AP.     

The thermal decomposition of NaHCO3 powders and single crystals

The thermal decomposition of four commercial powders and of differently stored single crystals of sodium hydrogen carbonate is studied by power compensation DSC and by optical and FT-IR microscopy. Independently of manufacturer, specified purity and price, the thermal curves of all the commercial powders show a more or less pronounced low temperature peak preceding the one due to the main decomposition. Such small peak is not observed when samples of laboratory recrystallized material are used. However the thermal behaviour of the latter preparation differs remarkably depending on storage conditions: the material kept in closed glass containers decomposes at temperatures higher than those of the material stored in a dessiccator in the presence of concentrated H₂SO₄. The observation by optical microscopy of the behaviour of the surfaces of single crystals coming from different storage conditions when the temperature is raised in a Kofler heater helps the interpretation of the data collected. The mechanism of the decomposition is discussed and the relevant kinetic parameters reported.     

等离子体法合成超细碳氮化钛固溶体微粉

本研究以tiCl4、CH4和N3或NH3为原料, 在直流电弧氢等离子体反应器中合成了三元超细碳氮化钛(TiCxN1-x)固溶体微粉。考察了不同氮源及其加入量对产物组成的影响。所得不同固溶度的微粉各自都具有均一的化学组成和相组成, 平均粒径<100um, 比表面>10m^2/g, 主相含量>97±10^-^2┘     

Thermal degradation behavior of radiation synthesized polydiallyldimethylammonium chloride

Thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) studies were carried out on gamma radiation synthesized polydiallyldimethylammonium chloride (PDADMAC). The polymer was found to undergo thermal degradation in two stages. The first stage showed a weight loss of 33% and the second stage showed a weight loss of 67%. The DSC thermogram shows two endothermic peaks corresponding to the two stages in the TG thermogram and the experimental enthalpy change associated with the first and second stages were 650 J g⁻¹ and 129.5 J g⁻¹, respectively. The nth-order kinetic parameters (order of the reaction, activation energy and the pre-exponential factor) were determined from a single dynamic DSC or thermogravimetric (TG) thermogram by the method of least square. Theoretical TG/differential thermogravimetric (DTG) and DSC thermograms derived from the calculated kinetic parameters were in good agreement with the experimental ones at the heating rate employed. However, the kinetic parameters determined using TG and DSC were different. This leads to the conclusion that the degradation mechanism could be complicated and may consists of a number of parallel or consecutive reactions. The glass transition temperature (T_g) of the polymer was found to be around 150 °C depending on the test method employed.     

Thermal behavior of polyacrylonitrile polymers synthesized under different conditions and comonomer compositions

Polyacrylonitrile (PAN) polymers are used as precursors for carbon fiber production. This process requires an oxidative stabilization step, which can be studied by differential scanning calorimetry (DSC). In this sense, thermal behavior of PAN based terpolymers by different polymerization processes, compositions and itaconic acid concentrations in the reaction media were investigated. The obtained results showed that the addition of itaconic acid and methyl acrylate as comonomers resulted a lower heat flow during the process comparing to the PAN homopolymer. It suggested that these comonomers aid the oxidative stabilization stage for all studied process. The redox system polymerization at 40°C resulted in a lower heat flow. Itaconic acid decreases slightly initial and peak temperatures of the terpolymer and heat flow until concentration of 3y. The cyclization temperature decreases when MAis incorporated into the terpolymer compared to the MMA terpolymer and increases when MAA is the acidic monomer. Among terpolymers the AN/MA/AA polymer showed the best thermal behavior for carbon fiber producing.     

新型柴油节能降污添加剂的研制

为改善柴油燃料的燃烧性能,充分利用有限的石油资源,通过对两种单剂的制备、筛选,研制了一种新型柴油节能降污表面修饰纳米添加剂 添加剂以0.01‰质量分数加入柴油中,能显著提高柴油的燃烧效率、减少残炭.     

étude thermodynamique de certains médicaments

Two compounds of sulphamide type:p-amino-benzene sulphonamide (I) and 3,4-dimethylisoxazol 5-sulphanylamide (II) were studied by combustion calorimetry and by differential scanning calorimetry (DSC).The enthalpies in solid state at 298,15 K of combustion, _c H _m ^o (I)=-2788,5±1,6 kJ mol^–1, _c H _m ^o (II)=-5036±3,8 kJ mol^–1 and of formation, _f H _m ^o (I)=-458,3±1,6 kJ mol^–1, _fH _m ^o (II)=-180,1±3,8 kJ mol^–1 were determined.The thermal effects concerning the melting and phase transition of this compounds were also measured.

     

Effect of nanoscale fully vulcanized acrylic rubber powders on crystallization of poly(butylene terephthalate): Isothermal crystallization

Poly(butylene terephthalate) (PBT) was blended with nanoscale fully vulcanized acrylic rubber (FVAR) powders in a twin extruder, and the FVAR powders were dispersed well in PBT from scanning electron microscopy (SEM) and transmission electron microscope (TEM) investigation. The isothermal crystallization kinetics of PBT/FVAR blends were investigated by differential scanning calorimeter (DSC) and simulated by Avrami model. Equilibrium melting temperature was estimated by the nonlinear Hoffman-Weeks relation. The active energy (ΔE) and nucleation parameters (K_g) increased with the addition of FVAR, suggesting that FVAR particles hindered the crystallization; however more content FVAR had a lower ΔE and K_g because FVAR powders acted as heterogeneous nuclei in the nucleation of crystallization and facilitated the crystallization of PBT. The crystallization ability followed the order: PBT > PBT/FVAR6 > PBT/FVAR3 > PBT/FVAR1 when undercooling was considered.     

A study of surface adsorption on silver powders

DSC and TG-DTA techniques were used to investigate micro-sized silver powder particles and the adsorption of ethyl cellulose on these particles in a solution of ethyl acetate. The apparent specific heat of the silver particles was determined, and the kinetics of temperature-programmed desorption (TPD) of these adsorbed silver particles was investigated. Results show that the apparent specific heat and desorption kinetic parameters obtained by thermal analysis techniques could be used to characterize certain physico-chemical properties of such a particulate system.     

Crosslinking kinetics studies on interpenetrating polymer network powder coatings

IPN powder coatings were prepared which were composed of (A) a pendant double bond-containing acrylic resin made by reacting m-isopropenyl-α-α-dimethylbenzyl isocyanate (TMI) and a hydroxyl-containing acrylic resin and (B) a bisphenol type epoxy resin of high molecular weight cured by means of a carboxylic acid-containing acrylic resin. Crosslinking kinetics studies were carried out by using a computerized differential scanning calorimeter (DSC). A computer program was designed to simulate the curing reactions of the IPN powder coatings by using the individual kinetic parameters obtained from DSC. The simulated results from the computer program are very close to the results from experimental thermograms (by DSC). Therefore, this methodology provides an efficient tool to simplify and predict kinetic studies of crosslinking reactions in current or new IPN powder coating systems.     

Quantitative Determination of Crystallinity of α-Lactose Monohydrate by DSC

In pharmaceutical practice it is important and useful to know the crystallinity of materials and to monitor it during formulation development, production processes and storage. The purpose of this study was to assess the quantitative capability of DSC for determining crystallinity in crystalline/amorphous powder mixtures and to compare the accuracy of the DSC method with that of conventional powder X-ray diffraction. Alpha-lactose monohydrate was chosen as the model material. On the basis of this study it can be concluded, that DSC method can be applied safely for semiquantitative evaluation of the crystallinity of lactose samples consisting of an amorphous content higher than 20%. This revised version was published online in August 2006 with corrections to the Cover Date.     

Feasibility Study of Crude Oil Fields by Thermal Analysis Techniques

This paper investigates the minimum oil content necessary for self-sustained combustion, which is introduced as a criterion for the selection of suitable reservoirs for in-situ combustion processes. Differential scanning calorimetry was used to determine the heat values of oil-limestone mixtures. The minimum temperature required for the total consumption of the fuel was obtained by thermogravimetry (TG/DTG). The minimum amount of oil necessary to sustain combustion was calculated from these two parameters and compared with the oil content of the reservoir. Reservoirs with an oil content greater than or equal to this minimum value were considered feasible. It was seen that the fields examined are generally not suitable for in-situ combustion processes. This revised version was published online in August 2006 with corrections to the Cover Date.     

Spectroscopic investigations of nanohydroxyapatite powders synthesized by conventional and ultrasonic coupled sol-gel routes

In the present work, the synthesis and characterization of nano-HAP powders by a novel ultrasonic coupled sol-gel synthesis is reported. The obtained powders were sintered by conventional means at different temperatures. In addition to this, HAP powders prepared through the sol-gel method without the aid of the ultrasonic waves is also studied. The obtained nano-HAP powders were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and scanning electron microscopic (SEM) techniques. The results have proved that the nano-HAP powders synthesized by ultrasonic coupled sol-gel synthesis showed remarkable reduction in the particle size when compared with the conventional sol-gel method and hence these powders could be used as a coating material in biomedical applications.     

Thermal behavior of polystyrene synthesized in the presence of carboxymethyl cellulose

Summary Study of the decomposition kinetics is an important tool for the development of polymer recycling in industrial scale. In this work, parameters such as activation energy, frequency factor and reaction order, were measured under dynamic conditions. Flynn-Wall-Ozawa, Van Krevelen, Horowitz-Metzger, Coats-Redfern, Madhusudanan and Vyazovkin methods were used to determine the kinetic parameters. The analysis of the results obtained by the Coats-Redfern method shows that the thermal degradation process of LDPE and HDPE corresponds to a phase boundary controlled reaction (mechanism R2). This method shows that the reaction order values of LDPE and HDPE are about 0.7 and 0.6, respectively.     

Transient DSC,a Novel and Rapid Method for Assessing Pharmaceutical Powder Compacts

The previously described method involving the use of transient DSC was applied to pharmaceutical powder compacts and to ceramic powder compacts. The samples were prepared by compressing powders of pentaerythritol tetraacetate and two kinds of alumina powder (differing in particle size distribution) up to a pressure of 20 MPa by using a jig. For pentaerythritol tetraacetate, a linear relationship was obtained between the parameter obtained by DSC and the compaction pressure. This revised version was published online in August 2006 with corrections to the Cover Date.     

Surfactant-free emulsion copolymerization of styrene and methyl methacrylate for preparation of water-redispersible polymeric powders

Poly(methyl methacrylate), polystyrene, and poly(styrene-co-methyl methacrylate) cationically stabilized latexes with up to 25% solid content were prepared by surfactant-free emulsion polymerization (SFEP) employing 1 mol % 2,2′-azobis[2-(2-imidazolin-2-yl)propane]dihydrochloride (VA-044) as an initiator and stabilizer (inisurf) with respect to monomer at 70 °C. The latexes had 200–500 nm z-diameter and a very narrow size distribution (PDI < 0.05). The stabilizing amidinium moieties from VA-044 were covalently bound to the particles. After drying in air, poly(styrene-co-methyl methacrylate), PS-co-PMMA latexes were easily redispersible in water simply by addition of water and a few minutes of gentle stirring. The redispersed latex particles had colloidal characteristics very similar to the original latex particles in terms of polydispersity, size, and zeta potential. In contrast, latexes prepared with a similar formulation but using a conventional cationic surfactant (CTAB) that was not covalently bound to the particles were not redispersible. This is the simplest method reported so far for the preparation of redispersible latexes that do not use high stabilizer concentrations. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2376–2381     

Approach to improving the toughness of TGMDA/DDS epoxy resin by blending with thermoplastic polymer powders

A series of hot-melt processable thermosetting compositions was prepared by blending N,N,N′,N′-tetraglycidyl-4,4′ -diaminodiphenyl-methane/4,4′-diaminodiphenylsulfone (TGMDA/DDS) epoxy resin and thermoplastic polymer powders with average particle size below 30 μm. The basic thermoplastic polymers were either a high T_g amorphous cardo polyimide (T_g=350°C) or commercial semicrystalline PA6 and PA12 polyamides. The resulting heterogeneous mixtures showed viscosity values below 5000 cps suitable for prepregging process. After cure, phase-separated morphologies were maintained with a rather limited interphase miscibility as demonstrated by thermomechanical analysis. Scanning electron microscope examination of fracture surfaces pointed out a strong adhesion between the powder particles and the surrounding polyepoxy network, particularly for the potentially reactive polyamide structures. Moreover, as shown by differential scanning calorimeter analysis, the crystallinity ratio of the PA6 and PA12 powders was lowered due to melting during thermal polymerization. The fracture toughness properties of the powder-containing materials were compared with those of a fully miscible cardo polyimide–TGMDA/DDS blend coming from an homogeneous resin composition. The best improvement in fracture energy was obtained for the powder-modified resins. The most effective composition filled with 16 wt% of powdered polyimide exhibited a fourfold increase in G_IC (388 J/m² versus 100 J/m²) without compromising the epoxy thermomechanical stability (T_g=227°C versus 223°C).     

Synthesis and Characterization of High-purity Aluminum Titanate with Water Quenching Method

High-purity aluminum titanate was synthesized via a water quenching method with waste-residue in the aluminum factory and industrial TiO2 as the main raw materials, which belongs to the comprehensive utilization of solid wastes. Compared with the conventional method, it can reduce synthesis temperature, effectively inhibit decomposition and raise the content of AT; the addition of tiny silicon powder can improve the sintering and optimize the properties of AT. The crystalline phase structure and microstructure of each sample were characterized with XRD and SEM methods; the content of each crystalline phase in each sample was confirmed with Rietveld Quantification method; the properties of each sample were also tested. The experimental results showed that No. 4 is the optimum specimen, with the corresponding mass ratio of Al2O3/TiO2 to be 1.27 and the content of AT of 97.2 wt%. The addition of optimum tiny silicon powder is confirmed to be 8wt%; its corresponding bulk density is 2.63 g/cm^3, bending strength is 46.34 MPa, and the retention of one thermal vibration bending strength is 71.5%.     

Ultrafine BaPb1-xBixO3 powders prepared by the spray-ICP technique

Ultrafine powders of a trnary oxide system, Ba–Pb–Bi–O, were prepared by spraying aqueous mixed solutions of Ba(NO₃)₂, Pb(NO₃)₂, and Bi(NO₃)₃ into an argon inductively coupled plasma of ultrahigh temperature above 5000 K (the spray-ICP technique). Phases of the powders were largely dependent on the powder collectors enclosing the tail flame and its successive gas flow. In the water-cooled collector, mixtures of amorphous and crystalline materials were formed. In the collector where the gas flow was spontaneously maintained at about 550°C by ICP itself, ultrafine BaPb_1–xBi_xO₃ (BPBO) 10–40 nm in particle diameter was obtained. The BPBO thus obtained had a few wt.% of water and carbonate. They were lost by heat treatment up to 550°C, and a single-phase BPBO was formed. The as-prepared BPBO (x=0.25) showed no superconducting transition down to 1.5 K, but the one having a particle diameter of 1 m formed by heating the as-prepared BPBO up to 1000°C had a superconducting transition temperature at 11.3 K.