Influence of the catalyst type on the growth of carbon nanotubes via methane chemical vapor deposition

The preparation of the catalyst is one of the key parameters which governs the quality of carbon nanotubes (CNTs) grown by catalyzed chemical vapor deposition (CVD). We investigated the influence of three different procedures of catalyst preparation on the type and diameter of CNTs formed under identical growth conditions via methane CVD. In the first one, chemically synthesized colloidal iron oxide or iron molybdenum alloy nanoparticles were used, which were homogeneously deposited on silicon substrates by spin coating to prevent them from coalescence under CVD growth conditions. The obtained multiwall CNTs (MWNTs) exhibited diameters corresponding to the catalyst particle size, whereas no formation of single-wall CNTs (SWNTs) was observed. In the second method, commercial porous alumina nanoparticles were used in association with iron and molybdenum salts and the Fe/Mo catalyst was formed in situ. We determined that the alumina concentration significantly influenced the morphology of the catalyst and that below a critical value of the range of 1 g/L no CNTs were formed. While yielding nearly defect-free SWNTs, their diameter could not be controlled using this procedure, resulting in a large distribution of tube sizes. In a third, new preparation method, associating alumina and iron-based nanoparticles, SWNTs of a different size and narrower diameter distribution as compared to the second method were obtained. Our results are evidence of the essential role of alumina particles in the formation of SWNTs, and the newly developed method opens up a way to the synthesis of diameter-controlled SWNTs via catalyzed CVD.     

Synthesis, morphology, and magnetic characterization of iron oxide nanowires and nanotubes

We have explored the synthesis of iron oxide particles, tubes, and fibrils within the pores of nanoporous polycarbonate and alumina membranes. The membranes contain uniformly distributed cylindrical pores with monodispersed diameters (varying between 20 and 200 nm) and thicknesses of 6 and 60 microm, respectively. By hydrolysis and polymerization of iron salts, particles of different sizes and phases were formed in the pores, building iron oxide particle nanowires. Alternatively, by the sol-gel technique, using as reagents metalloorganic compounds, fibrils and tubes of different iron oxide phases were prepared. Structural and morphological investigations performed using scanning electron microscopy and transmission electron microscopy revealed ordered iron oxide particle wires, tubes, and fibrils formed inside the membrane nanopores. Magnetic characterization was accomplished with a vibrating sample magnetometer. Below the blocking temperature (T(B)), the magnetic behavior of the nanowires was governed by dipolar interaction between nearest-neighbor nanoparticles inside the pore, whereas the energy barrier, and therefore the T(B) value, was mainly governed by dipolar interaction between magnetic moments over larger (interpore) distances. As expected, crystalline iron oxide nanotubes exhibited magnetic perpendicular anisotropy due to their magnetocrystalline and shape anisotropy.     

Fabricating gold nanoparticle-oxide nanotube composite materials by a self-assembly method

Composition of nanostructured metal particles on oxide tubes (TiO2 and ZrO2) were fabricated and characterized. The composite materials were examined by transmission electron microscopy, scanning electron microscopy, FT-IR absorption, and UV-visible absorption spectra. The results of characterization showed that the composites indeed contained both oxide tubes and gold nanoparticles and that the gold nanoparticles were intimately associated with the nanotubes.     

Fe/Co alloys for the catalytic chemical vapor deposition synthesis of single- and double-walled carbon nanotubes (CNTs). 1. The CNT-Fe/Co-MgO system

Mg(0.90)Fe(x)Co(y)O (x + y = 0.1) solid solutions were synthesized by the ureic combustion route. Upon reduction at 1000 degrees C in H2-CH4 of these powders, Fe/Co alloy nanoparticles are formed, which are involved in the formation of carbon nanotubes, which are mostly single and double walled, with an average diameter close to 2.5 nm. Characterizations of the materials are performed using 57Fe M?ssbauer spectroscopy and electron microscopy, and a well-established macroscopic method, based on specific-surface-area measurements, was applied to quantify the carbon quality and the nanotubes quantity. A detailed investigation of the Fe/Co alloys' formation and composition is reported. An increasing fraction of Co2+ ions hinders the dissolution of iron in the MgO lattice and favors the formation of MgFe2O4-like particles in the oxide powders. Upon reduction, these particles form alpha-Fe/Co particles with a size and composition (close to Fe(0.50)Co(0.50)) adequate for the increased production of carbon nanotubes. However, larger particles are also produced resulting in the formation of undesirable carbon species. The highest CNT quantity and carbon quality are eventually obtained upon reduction of the iron-free Mg(0.90)Co(0.10)O solid solution, in the absence of clusters of metal ions in the starting material.     

Formation of anatase TiO2 nanoparticles on carbon nanotubes

Anatase TiO2 nanoparticles with a size range of 2 to 10 nm have been formed on carbon nanotubes by the controlled hydrolysis and condensation of titanium bis-ammonium lactato dihydroxide in water and electrosterically dispersed carbon nanotubes.     

Optimal design and characterization of superparamagnetic iron oxide nanoparticles coated with polyvinyl alcohol for targeted delivery and imaging

Superparamagnetic iron oxide nanoparticles (SPION) with narrow size distribution and stabilized by polyvinyl alcohol (PVA) were synthesized. The particles were prepared by a coprecipitation technique using ferric and ferrous salts with a molar Fe3+/Fe2+ ratio of 2. Using a design of experiments (DOE) approach, the effect of different synthesis parameters (stirring rate and base molarity) on the structure, morphology, saturation magnetization, purity, size, and size distribution of the synthesized magnetite nanoparticles was studied by various analysis techniques including X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) with differential scanning calorimetry (DSC) measurements, vibrating-sample magnetometer (VSM), transmission electron microscopy (TEM), UV-visible, and Fourier transform infrared (FT-IR) spectrometer. PVA not only stabilized the colloid but also played a role in preventing further growth of SPION followed by the formation of large agglomerates by chemisorption on the surface of particles. A rich behavior in particle size, particle formation, and super paramagnetic properties is observed as a function of molarity and stirring conditions. The particle size and the magnetic properties as well as particle shape and aggregation (individual nanoparticles, magnetic beads, and magnetite colloidal nanocrystal clusters (CNCs) are found to be influenced by changes in the stirring rate and the base molarity. The formation of magnetic beads results in a decrease in the saturation magnetization, while CNCs lead to an increase in saturation magnetization. On the basis of the DOE methodology and the resulting 3-D response surfaces for particle size and magnetic properties, it is shown that optimum regions for stirring rate and molarity can be obtained to achieve coated SPION with desirable size, purity, magnetization, and shape.     

Titania nanoparticles synthesis in mesoporous molecular sieve MCM-41

Nanocrystalline titanium oxide (TiO(2)) is one of the most useful oxide material, because of its widespread applications in photocatalysis, solar energy conversion, sensors and optoelectronics. The control of particle size and monodispersity of TiO(2) nanoparticles is a challenging task. The use of MCM-41, an inorganic template of uniform pore size (2-10 nm), can overcome this difficulty and produce stable nanoparticles of uniform size and shape. Here, we demonstrate the synthesis of titania nanoparticles inside the pores of silica based MCM-41 forming a TiO(2)/Si-MCM composite. Composites are formed in the alcoholic medium by incipient wetness impregnation method. Titania particles of average 3 nm size are obtained. Effect of silica and titania precursors on the quality of nanoparticles has been investigated. The characterization of titania-MCM-41 composites has been carried out using a variety of techniques like UV-vis absorption spectroscopy, X-ray diffraction, FT-IR spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy and photoluminescence spectroscopy. It has been found that the titania particles are co-ordinated with Si-MCM by SiOTi covalent bond.     

Hydrothermal synthesis, characterization, and photocatalytic performance of silica-modified titanium dioxide nanoparticles

Silica-modified titanium dioxides were prepared by a hydrothermal method and then characterized by XRD, FT-IR, XPS, TEM, and UV-visible spectroscopy. The silica-modified titanium dioxides were in anatase phase and had large surface areas. There was strong interaction between SiO2 and TiO2, and TiOSi bonds formed during the hydrothermal process. The addition of silica in TiO2 particles could effectively suppress the formation of the rutile phase and the growth of titanium dioxide crystals. DRS spectra proved an increase in the band-gap transition with the increase of silica. The silica-modified TiO2 nanoparticles exhibited better photocatalytic activity, which increased with the silica amount, in comparison with pure TiO2 nanoparticles. Due to better thermal stability, the photocatalytic activity of the silica-modified TiO2 sample held good photocatalytic activity even after calcined at 1273 K.     

Pyrogenic iron(III)-doped TiO2 nanopowders synthesized in RF thermal plasma: phase formation, defect structure, band gap, and magnetic properties

Iron(III)-doped TiO(2) nanopowders, with controlled iron to titanium atomic ratios (R(Fe/Ti)) ranging from nominal 0 to 20%, were synthesized using oxidative pyrolysis of liquid-feed metallorganic precursors in a radiation-frequency (RF) thermal plasma. The valence of iron doped in the TiO(2), phase formation, defect structures, band gaps, and magnetic properties of the resultant nanopowders were systematically investigated using M?ssbauer spectroscopy, XRD, Raman spectroscopy, TEM/HRTEM, UV-vis spectroscopy, and measurements of magnetic properties. The iron doped in TiO(2) was trivalent (3+) in a high-spin state as determined by the isomer shift and quadrupole splitting from the M?ssbauer spectra. No other phases except anatase and rutile TiO(2) were identified in the resultant nanopowders. Interestingly, thermodynamically metastable anatase predominated in the undoped TiO(2) nanopowders, which can be explained from a kinetic point of view based on classical homogeneous nucleation theory. With iron doping, the formation of rutile was strongly promoted because rutile is more tolerant than anatase to the defects such as oxygen vacancies resulting from the substitution of Fe(3+) for Ti(4+) in TiO(2). The concentration of oxygen vacancies reached a maximum at R(Fe/Ti) = 2% above which excessive oxygen vacancies tended to concentrate. As a result of this concentration, an extended defect like crystallographic shear (CS) structure was established. With iron doping, red shift of the absorption edges occurred in addition to the d-d electron transition of iron in the visible light region. The as-prepared iron-doped TiO(2) nanopowders were paramagnetic in nature at room temperature.     

Preparation of magnetic polystyrene latex via the miniemulsion polymerization technique

Magnetic iron oxide (magnetite, Fe₃O₄) nanoparticles were encapsulated with polystyrene to give a stable water‐based magnetic polymer latex, using the miniemulsion polymerization technique. The resulting magnetic latexes were characterized with transmission electron microscopy (TEM), dynamic light scattering (DLS), vibrating sample magnetometer measurements (VSM), and ⁵⁷Fe Mössbauer spectroscopy measurements. TEM revealed that all magnetite nanoparticles were embedded in the polymer spheres, leaving no empty polystyrene particles. The distribution of magnetite particles within the polystyrene spheres was inhomogeneous, showing an uneven polar appearance. The DLS measurements indicated a bimodal size distribution for the particles in the latexes. According to our magnetometry and Mössbauer spectroscopy data, the encapsulated magnetite particles conserve their superparamagnetic feature when they are separated in the polymer matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4802–4808, 2004     

Constrained iron catalysts for single-walled carbon nanotube growth

The diameter of single walled carbon nanotubes (SWNTs) determines the electronic properties of the nanotube. The diameter of carbon nanotubes is dictated by the diameter of the catalyst particle. Here we describe the use of iron nanoparticles synthesized within the Dps protein cage as catalysts for the growth of single-walled carbon nanotubes. The discrete iron particles synthesized within the Dps protein cages when used as catalyst particles gives rise to single-walled carbon nanotubes with a limited diameter distribution.     

Size control synthesis of sulfur doped titanium dioxide （anatase） nanoparticles, its optical property and its photo catalytic reactivity for CO2 ＋ H2O conversion and phenol degradation

Sulfur doped anatase TiO2 nanoparticles (3 nm−12 nm) were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles (24 nm). The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2+H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.     

Preparation of TiO2/CNTs nanocomposite and its catalytic performance on the thermal decomposition of ammonium perchlorate

Transition Metal Chemistry - Composite particles of carbon nanotubes (CNTs) and titanium dioxide (TiO2) were prepared by a sol-flux method. Characterization of TiO2/CNTs nanocomposite was performed...     

Surface Polymers on Multiwalled Carbon Nanotubes for Selective Extraction and Electrochemical Determination of Rhodamine B in Food Samples

In this study, we combine magnetic solid phase extraction (MSPE), with the screen-printed carbon electrode (SPCE) modified by a molecular imprinted polymer (MIP) for sensitive and selective extraction and electrochemical determination of Rhodamine B in food samples. A magnetic solid phase extraction (MSPE) was carried out using magnetic poly(styrene-co-divinylbenzene) (PS-DVB) and magnetic nanoparticles (MNPs) synthetized on the surface of multiwalled carbon nanotubes (MWCNTs). An MIP was prepared on the surface of MWCNTs in the presence of titanium oxide nanoparticles (TiO₂NPs) modifying the SPCE for the rapid electrochemical detection of Rhodamine B. The MIPs synthesis was optimized by varying the activated titanium oxide (TiO₂) and multiwalled carbon nanotubes (MWCNTs) amounts. The MSPE and electrochemical detection conditions were optimized as well. The present method exhibited good selectivity, high sensitivity, and good reproducibility towards the determination of Rhodamine B, making it a suitable method for the determination of Rhodamine B in food samples.     

Controlling the size of magnetic nanoparticles using pluronic block copolymer surfactants

We have successfully controlled the size of magnetic nanoparticles by adjusting the surfactant/solvent ratio. Gamma-Fe(2)O(3) nanoparticles of 5.6 and 12.7, and Fe(0) nanoparticles of 22.3 nm in diameter were prepared, all having spherical shape and uniform size as confirmed by TEM. M?ssbauer spectra confirmed Fe(3+) for the 5.6 and 12.7 nm particles and Fe(3+) and Fe(0) for 22.3 nm particles, in good agreement with synchrotron XRD patterns. Both room temperature and 5 K H-M measurements show that 22.3 nm particles have much higher magnetization than their oxide counterparts, in agreement with their being Fe(0). T-M measurements show superparamagnetism for 5.6 and 12.7 nm particles and ferromagnetism for 22.3 nm particles.     

CNTs/TiO2多孔复合膜的组装及光催化性能

提出了一种在掺氟的SnO2(FTO)导电玻璃上组装碳纳米管(CNTs)/Fe-Ni/TiO2多孔复合膜光催化剂的新方法.采用喷涂热解法(SPD)将掺杂镍和铁的含有嵌段聚合物P123的二氧化钛前驱体溶胶涂覆在FTO导电玻璃上,制备Fe-Ni/TiO2多孔膜,再采用化学气相沉积法(CVD)在Fe-Ni/TiO2膜上原位生长CNTs,得到CNTs/Fe-Ni/TiO2多孔复合膜光催化剂.CNTs/Fe-Ni/TiO2复合膜具有多级孔结构特征,在TiO2表面原位生长的CNTs不但具有较好的石墨化结构,且CNTs较均匀地分布在整个膜层的孔中.考察了CNTs/Fe-Ni/TiO2复合膜光催化剂的结构和性能,并通过降解甲基橙溶液评价了复合膜的光催化活性.结果表明,CNTs的复合及铁和镍的掺杂等改性显著提高了TiO2膜材料的光催化活性.     

由钛铁矿制备Fe3O4/TiO2复合物的研究进展

归纳了从钛铁矿中分离铁和二氧化钛的方法,包括亚熔盐法、预氧化法、还原锈蚀法;其次,初步总结了目前国内外制备Fe_3O_4磁性纳米颗粒和TiO_2纳米粒子的方法。最后,对Fe_3O_4/TiO_2复合材料的制备方法包括溶胶-凝胶法、微乳液法、均匀沉淀法作了梳理。Fe_3O_4/TiO_2复合纳米材料很好地解决了单独使用TiO_2作为废水处理催化剂,在实际应用过程中易随水流失,难以回收利用的问题,具有一定的实用性。     

Mössbauer Spectroscopic Studies of Supported α-Fe2O3 and Fe Catalysts I: Particle Size Determination and Support Effect

The chemical state of particles of 5wt% Fe in α-Fe₂O₃ and the subsequently reduced iron particles supported on different particle size (50–200 mesh) of silica (SiO₂), alumina (Al₂O₃), magnesium oxide (MgO) and carbon (C) was examined by Mössbauer spectroscopy at various stages of calcination and reduction. The particle size of the α-Fe₂O₃ supported on different mesh sizes (50, 100, 140, 200 mesh) of SiO₂ has been determined. The strength of metal-support interaction with respect to the kind of support was found to be MgO>SiO₂>Al₂O₃>C.     

制备均一形貌的长二氧化钛纳米管

在温和的水热条件下,用碱溶液处理不同粒径的锐钛矿相和金红石相二氧化钛 纳米粉体,得到了不同形貌的二氧化钛纳米管,并用TEM,XRD,FT-Raman和BET等 对其进行了表征。金红石相的超细纳米晶有利于形成均一形貌的纳米管,用粒径仅 为7.2 nm的金红石相纳米粉体为前驱体得到了长度为500 nm的长二氧化钛纳米管。 用纳米晶反应活性对晶粒尺寸的依赖性及晶相稳定性解释了长纳米管的形成机理。     

Preparation and characterization of submicron hybrid magnetic latex particles

Micrometer magnetic hybrid particles are of great interest in biomedical field, and various morphologies have been prepared via encapsulation processes. Regarding submicron, only few processes have been investigated and the most recent one leading to highly magnetic submicron magnetic hybrid particles is based on oil in water magnetic emulsion (MES) transformation. The encapsulation of magnetic iron oxide nanoparticles forming oil in water MES was investigated using different styrene/cross‐linker divinylbenzene volume ratio in the presence of potassium persulfate initiator. The encapsulation performed in this work is basically conducted by using well‐defined oil in water MES as a seed in radical emulsion polymerization. The chemical composition, morphology, iron oxide content, magnetic properties, electrokinetic properties, particle size, and size distribution of the prepared magnetic hybrid particles were examined using various techniques. The desired perfect magnetic core and polymer shell morphology were successfully obtained, and the final magnetic hybrid particles are superparamagnetic in nature and exhibit high iron oxide content (64 wt %). Copyright © 2015 John Wiley & Sons, Ltd.