具有连续纵向激励模态宽带水声换能器研究

摘要分析了连续纵向激励模态拓宽频带的机理。采用单侧激励，可同时激励奇次模态和偶次模态，利用有限元方法研究了这些模态在水中随几何尺寸变化的规律，通过优化设计制作了接近两个倍频程的宽带换能器样品，其工作带宽为12kHz-44kHz，频带内的起伏为±4．3dB。为进一步减少带宽内响应起伏的大小，通过对模态节点间增加质量钢块以及对后盖板采用机械阻抗匹配腔的方式，制作了工作带宽为12kHz-34kHz，频带内的起伏为±3．7dB的宽带换能器样品。     

前盖板开矩形通孔型宽带换能器

提出一种利用多模态耦合的开孔型宽带换能器。在传统纵振换能器前盖板一定距离处开一矩形通孔,以激发出能与纵振耦合从而拓宽频带的振动模态。以带宽为目标,利用有限元方法对通孔的长度、宽度和孔前端离前盖板端面的距离进行了优化设计,得到了最佳的开孔位置和尺寸。研制了换能器样机。测试结果表明,在12~32 kHz频带范围内,换能器有3个工作模态,后两阶模态对工作带宽的展宽有贡献。未开孔的同尺寸纵振换能器-3 dB带宽仅3 kHz,开孔换能器带宽则达10.50 kHz,有效地拓展了工作带宽。理论计算和测试结果吻合较好。     

Janus-Helmholtz换能器的弱辐射耦合机理与带宽特性

针对Janus-Helmholtz (JH)换能器频带内响应起伏较大、模态耦合机制尚不明确的问题,提出了振动模态声辐射独立建模方法。该方法建立换能器各个振动模的独立有限元模型,在仿真计算中将位移载荷直接加载在辐射面上,分析振动模的辐射声场。通过各个结果的对比分析,观察到JH换能器声辐射模态的弱耦合规律,最终给出JH换能器带宽特性的合理物理解释,即JH换能器在同一纵向振子激励下,由于不存在声输出明显干涉加强的模态耦合,因此难以得到通常意义上响应起伏小于3 dB的宽带工作性能。以控制工作频带内响应起伏较小为前提,将拓宽工作频带作为设计目标,优化设计了 JH换能器结构参数。实验中换能器样机的发射电压响应测试结果与仿真计算相吻合,实测谐振频率为1350 Hz与2450 Hz,谐振频率下发射电压响应分别为143 dB,141 dB,在频带1200~3300 Hz范围内响应起伏12 dB,最大声源级204 dB,实现了宽带大功率发射的特性。     

换能器前辐射头与轴向相平行方向的弯曲振动

复合棒型换能器前面的变截面组件在工作时常伴有弯曲振动现象，这在一定程度上会影响换能器的工作性能；利用复合棒型换能器的纵向振动基频与前辐射头弯曲振动的恰当耦合，可展宽换能器的频带。本文用有限元法，研究了前辐射头在声换能器组成中的弯曲振动问题，与测试结果相吻合。     

低频宽带大功率“星型”柱面发射换能器

提出一种具有水平无指向性、低频、宽带、大功率特点的新结构换能器——“星型”柱面发射换能器,换能器由共享后质量块的6个复合棒换能器按“星型”方式组成柱面结构。采用有限元方法对换能器进行了分析设计并制作了换能器样机。在1—10 kHz内,换能器有3个主要工作模态,前两阶工作模态对换能器工作带宽的展宽有贡献,第三阶模态显示出较强的指向性,水池测试换能器具有1倍频程的工作带宽,最大声源级为199.1 dB。有限元模拟结果和实验结果符合较好。研究结果表明,新结构换能器在满足水平无指向性的前提下,利用复合棒的纵振及辐射面的弯曲振动实现了低频、宽带、大功率的要求,提供了一种设计该特性换能器的新思路。     

具有阻抗匹配层的宽带纵向振动压电换能器设计

本文研究纵向振动压电换能器的频带展宽问题。在复合棒纵向换能器的辐射端加工适当材料的阻抗匹配层,可以使其工作在非单谐振状态下,在单层阻抗匹配层的情况下,合理地选择匹配层的厚度可以调整其谐振点之间的位置,从而改善换能器的辐射特性。本研究结果表明,对于机械品质因素Qm=6,发射响应带宽△f=4kHz的纵向振子,采用四分之一波长厚度的匹配层,在不降低发射响应的条件下,可展宽频带一倍以上。     

弛豫铁电单晶/压电陶瓷混合激励换能器EI北大核心CSCD

为了降低纵向换能器尺寸并提高发射带宽和发送电压响应,研究了一种弛豫铁电单晶/压电陶瓷混合激励换能器,换能器由[011]方向极化PIN-PMN-PT单晶和PZT-4压电陶瓷混合激励,利用多模态振动耦合的原理,通过单晶的32模式振动,可以灵活调整两种振子之间的驱动能力和刚度分配。首先通过四端网络法得到了换能器等效电路并计算了其谐振频率,然后利用有限元方法对换能器进行了仿真优化,最后制作了试验样机并进行了测试分析。换能器样机外径86 mm、长度80 mm,工作频带13~38 kHz,最大发送电压响应为144.9 dB,带内发送电压响应起伏小于6 dB,具有良好的宽带、小尺寸工作性能。     

一种拓宽匹配层换能器带宽的方法

本文介绍了一种拓宽匹配层换能器带宽的方法,通过单端激励以同时激发换能器的奇次和偶次谐波,以此来达到拓宽匹配层换能器带宽的目的。运用有限元软件ANSYS进行了建模分析计算,对其设计过程、测量结果作了分析介绍。样品换能器在10kHz～30kHz的频段内,发送电压响应起伏为±3.3dB。     

四激励二维正交复合夹心式压电超声换能器的设计

提出了一种四激励二维正交复合夹心式压电超声换能器,换能器由四组纵向极化压电陶瓷晶堆、一个中心耦合金属块和四个外部金属圆锥组成。基于二维耦合振动机理和机电类比原理,建立了换能器的等效电路模型并推导了其谐振频率方程。利用有限元软件仿真分析了四激励正交复合换能器的频响特性和振动特性,并与其单独一个方向振子的振动特性进行了对比。加工了反相和同相模态的换能器,利用阻抗分析仪和激光测振仪测试了其频率响应和二维四向纵振动输出特性,并进行了大功率二维四向超声乳化实验测试。理论、仿真和实验结果表明:换能器具有反相和同相两个纵向正交共振模态,在这两种共振模态下均可实现二维四向纵振动输出,且换能器两个正交方向振子的纵向振动具有相互耦合加强的作用;等效电路法和有限元法所得换能器的共振频率和有效机电耦合系数与实验测试结果吻合,通过与单激励正交复合夹心式压电超声换能器的有效机电耦合系数对比,发现该换能器具有更高的有效机电耦合系数。     

多谐振宽带Janus-Ring换能器

提出了一种多谐振宽带Janus-Ring换能器,两个一定距离的压电圆环换能器(Ring换能器)嵌套在双面纵振Janus换能器的两端,Ring换能器的径向振动、Janus换能器的纵振动与它们中间形成的Helmholtz液腔振动相耦合,可大大拓展换能器的工作带宽。使用有限元方法设计并研制了Janus-Ring换能器样机,经测试在1.8~8.0 kHz范围内,样机最大发射电压响应144 dB,起伏小于6 dB。相比传统的Janus-Helmholtz换能器,Janus-Ring换能器有效拓展了工作频带,增大了发射电压响应,减小了频带内的发射电压响应起伏。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.