高功率二极管激光器相变冷却技术

根据高功率二极管激光器的散热需求,设计了一种储能式相变冷却实验系统,并开展了喷雾相变冷却器和微通道相变冷却器的设计。采用多孔微结构的换热表面,用氨做制冷剂,实现了喷雾相变冷却器表面温度37 ℃时,散热功率密度达到了511 W/cm2。采用节流汽化原理,分别设计了背冷式相变微通道冷却器和薄片型的模块式相变微通道冷却器,背冷式相变微通道冷却器采用氨做制冷剂, 散热功率密度达到了550 W/cm2,采用R124做制冷剂,散热功率密度约270 W/cm2。采用R124做制冷剂,实现了脉冲激光功率3 kW和连续激光功率100 W的相变冷却二极管激光器模块封装。     

石墨片作辅助热沉的高功率半导体激光器热传导特性

为使边发射高功率单管半导体激光器有源区温度降低,增加封装结构的散热性能,降低器件封装成本,提出一种采用高热导率的石墨片作为辅助热沉的高功率半导体激光器封装结构。利用有限元分析研究了采用石墨片作辅助热沉后,封装器件的工作热阻更低,散热效果更好。研究分析过渡热沉铜钨合金与辅助热沉石墨的宽度尺寸变化对半导体激光器有源区温度的影响。新型封装结构与使用铜钨合金作为过渡热沉的传统结构相比,有源区结温降低4.5 K,热阻降低0.45 K/W。通过计算可知,激光器的最大输出功率为20.6 W。在研究结果的指导下,确定铜钨合金与石墨的结构尺寸,以达到最好的散热效果。     

高密度封装二极管激光器阵列

 理论模拟了自制的高效冷却器的散热能力,分析了单元封装结构所需材料的导热特性,获得了高功率二极管激光器在高功率密度、高占空比条件下运行的可行性。改进了高密度封装的关键工艺,热沉金属化层达到了3~5 mm,焊料厚度为4~7 mm,封装间距0.6 mm,采用峰值功率1 kW的背冷式叠阵二极管激光器。实验测试结果表明:封装的二极管激光器叠阵单元的整体封装热阻为0.115 ℃/W,有良好的散热能力;该叠阵模块在电流为100 A、占空比15%时,输出峰值功率为986 W,峰值功率密度达到1.5 kW/cm2,平均每个板条的斜效率为1.25 W/A,激光器阈值电流为20 A左右。     

大功率半导体激光器叠层无氧铜微通道热沉

建立了叠层无氧铜微通道热沉的散热模型,通过理论计算和近似分析,优化了微通道热沉的结构参数;在t=200μm, ωc=60μm, ωf=100μm,p=2. 02×106 Pa时,可获得最小热沉热阻Rthm =4. 205×10-3 K·cm2 /W。根据优化结果,考虑微通道取向对液压降的影响,设计了一种新型大功率半导体激光器叠阵用五层结构叠层无氧铜微通道热沉,并结合实际工艺制备了无氧铜微通道热沉。在实际工作中,优化结果往往要跟实际工艺相结合,如优化所得的水压降为 2 02×106 Pa,这在实际工艺中较难实现。但在热沉实际工作的水压降条件下,热阻为 4. 982×10-3 K·cm2 /W,它能满足高功率激光器叠阵的需要。     

基于沸腾-空化耦合效应的微通道线阵LD用热沉

 针对大功率LD的冷却需求,基于沸腾-空化耦合效应,研制了一种微通道相变热沉,封装腔长1.5 mm的LD线阵。依据加工条件确定通道宽度、深度以及间距,采用2维数值模型估算了通道长度,热沉材料采用无氧铜,多层叠焊,外形尺寸为20 mm×12 mm×1.6 mm。实验测试了连续功率LD输出0～100 W时的电 光转换效率以及电流 输出功率等特性,冷却工质采用R134a,磁驱齿轮泵电机转速50 r/s时热沉热阻为0.3 ℃/W。结果显示微通道相变热沉具有良好的散热能力,能够满足大功率LD的散热要求。     

激光二极管高效铜微通道冷却器设计

 通过对铜微通道冷却器的散热分析，设计出５层结构的模块式铜微通道冷却器。采用常规的线切割工艺加工，散热通道宽大约200μm，深300μm，各层间用真空钎焊的方法组装。该冷却器对于腔长06mm、宽10mm的线阵激光二极管芯片热阻为0.58℃/W。通过面阵激光二极管封装实验证明，该冷却器可用于10％占空比工作的面阵激光二极管封装。     

20％占空比2．5kW二维叠阵二极管激光器

采用Cu-WCu复合结构研制了一种五层结构的模块式微通道冷却器，并用所研制的冷却器封装出了20％占空比工作，峰值功率2．5kW的二维叠阵DL。制作的冷却器为五层结构，由上盖片、上散热片、分水片、下散热片和下盖片扩散焊成。散热片和分水片采用具有高热导率的无氧铜制作，上、下盖片采用硬度高，热导率也较高的WCu合金制作。这种结构不仅避免了无氧铜较软，面形和棱边质量难控制的缺点，还可提高冷却器的强度，     

连续100W量子阱二极管激光器封装工艺

为了提高激光器输出功率,对研制的铜微通道冷却器性能进行了测试,分析了其散热能力。设计了一种在软焊料中掺杂金属添加剂的工艺,有效抑制了晶须生长,并利用该冷却器和新工艺封装出了连续100W大功率二极管激光器,并对封装的器件进行了性能测试。测试结果表明,封装的连续100W器件在工作电流105 A时,输出功率超过了100W,中心波长为808.5 nm,光谱半高宽为2.15 nm,器件的smile尺寸小于2μm,部分值小于0.5μm。     

二极管激光器阵列微通道冷却实验研究

针对某二极管激光器阵列现有冷却器的实际问题,设计并制作了一种铜基液冷微通道冷却器.采用细密的短微通道来代替原来较宽的长通道,大幅度提高了有限空间内的对流换热面积,并可充分利用入口效应来增强换热,从而在保持较低流动阻力、较高流体流量和较低流体温升的前提下,显著提高了冷却器整体冷却能力,并改善了冷却器与热源器件界面上的温度分布均匀性.在本实验最大流量G=70 mL/s情况下,微通道部分的压降只有10.3 kPa;当冷却器与热源器件界面上的平均温升为25.7 K时,冷却器的散热能力可达730 W,相当于128.5 W/cm2的界面热流密度.实验结果还验证了Shah和London提出的表观阻力系数关联式、用于预测平均努谢尔数的Sieder-Tate关联式以及Shah&London关联式.     

泵浦用高平均功率二极管激光器研制

针对高平均功率线阵二极管激光器(DL )芯片的工作要求,开展了相应的封装结构设计和高效冷却技术研究.封装的单条线阵DL连续输出激光功率50 W,工作寿命达到5 000 h,10%占空比准连续输出激光脉冲功率150 W,25%占空比准连续输出激光脉冲功率100 W,工作寿命达到5×109次脉冲.采用模块式封装方式由25个模块堆叠,制作出了连续激光功率1 kW和20%占空比工作脉冲功率2.5 kW的叠阵二极管激光器.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.