Spectrophotometric Multicommutated Flow System for the Determination of Hypochlorite in Bleaching Products

Abstract

A multicommutation flow system for the spectrophotometric determination of hypochlorite in bleaching products is proposed. In this system, N,N-diethyl-p-phenylenediamine (DPD) reacts with hypochlorite, and the product was monitored at 515 nm. The analytical curve for hypochlorite was linear in the concentration range from 2.68 × 10^?5 to 1.88 × 10^?4 mol L^?1 (2–14 mg L^?1) with a detection limit of 6.84 × 10^?6 mol L^?1 (0.51 mg L^?1). The sampling rate was 45 h^?1, and a relative standard deviation of 1.4% (n = 10) was obtained. The recovery of this analyte ranged from 97.2% to 102.5%, and the results found using the proposed spectrophotometric multicommutated flow system agreed with the data obtained using a reference method (iodometric titration) at the 95% confidence level.     

Simple and fast voltammetric procedure of U(VI) determination in the presence of high concentrations of surface active substances

In this work, a simple and fast procedure for elimination of interfering surface active substances and for U(VI) adsorptive stripping voltammetric determination was developed. The adsorption in the form of U(VI)-cupferron complexes was performed, because as it was proved before, U(VI) forms with cupferron stable complexes, which were employed in voltammetric procedures. The procedure is based on two steps: the first is an adsorption of surface active substances onto an Amberlite XAD-16 or XAD-7 resin and the second is a voltammetric determination of U(VI) with a pulsed potential of accumulation alternate –0.65–0.3 V with the frequency of 0.5 Hz and then the differential pulse voltammogram was recorded, whereas the potential was scanned from –0.65 to –1.2 V. The detection limit estimated from three times the standard deviation for a low U(VI) concentrations was equal to 1.7 × 10^?10 mol L^?1 (7.2 × 10^?8 g L^?1). The linear range of U(VI) was observed over the concentration range from 5.0 × 10^?10 mol L^?1 (2.1 × 10^?7 g L^?1) to 2.0 × 10^?8 mol L^?1 (8.5 × 10^?6 g L^?1) for an accumulation time of 60 s. The influence of different kinds of surfactants, such as non-ionic, cationic and anionic on the uranium voltammetric signal was studied. The results confirm the possibility of U(VI) determination in water samples containing high concentrations of surface active substances even up to 50 mg L^?1.     

Spectrophotometric Determination of Bromate in Water Using Multisyringe Flow Injection Analysis

A multisyringe flow injection system for the spectrophotometric determination of bromate in water is proposed, based on the oxidation of phenothiazine compounds by bromate in acidic medium. Several phenothiazines were tested, including chlorpromazine, trifluoperazine, and thioridazine. Higher sensitivity and lower LOD were attained for chlorpromazine. Interference from nitrite, hypochlorite, and chlorite was eliminated in-line, without any changes in the manifold. The automatic methodology using chlorpromazine allowed the determination of bromate between 25 and 750 µg L^?1, with LOD of 6 µg L^?1, good precision (RSD < 1.6%, n = 10), and determination frequency of 35 h^?1.     

A New Flow‐Injection Chemiluminescence Method for the Determination of Acyclovir and Gancyclovir

Abstract

A rapid and sensitive flow‐injection chemiluminescence (FI‐CL) method, which is based on the CL intensity that generated from the redox reaction of Ce(IV)‐rhodamine B in H₂SO₄ medium, for the determination of acyclovir and gancyclovir is described. For acyclovir, the determination range is 3×10^?8 g mL^?1–7×10^?5 g mL^?1, with 1.56×10^?8 g mL^?1 as its determination limit. During 11 repeated measurements for 1×10^?6 g mL^?1 acyclovir, the relative standard deviation was 2.08%. For gancyclovir, the determination range was 5×10^?8 g mL^?1–7×10^?5 g mL^?1, with 2.35×10^?8 g mL^?1 as its determination limit. The relative standard deviation is 2.83% with 11 repeated measurements of 1×10^?6 g mL^?1 gancyclovir. This method can be successfully used to determine the content of acyclovir and gancyclovir in injections, acyclovir in eye drops, and, maybe, also for other ciclovirs.     

Use of ionic liquid based chitosan as sorbent for preconcentration of fluoroquinolones in milk,egg, fish,bovine, and chicken meat samples by solid phase extraction prior to HPLC determination

The possibility of using ionic liquid based chitosan sorbent for the separation and preconcentration of fluoroquinolone antibiotics (marbofloxacin, enoxacin, ofloxacin, ciprofloxacin, and enrofloxacin) has been studied. For this reason, different ionic liquids were prepared and coated on the chitosan sorbent. The conditions of the preconcentration of fluoroquinolones on a microcolumn have been optimized and the extraction efficiencies of the prepared sorbents have been compared. The compounds were eluted with 5 mL of 20% NH₃ (v/v, MeOH) solution and determined by HPLC with diode array and fluorescence detector. The limits of detection were found as 4.23 µ g L^?1 for marbofloxacin, and 1.09 µg L^?1 for enoxacin; 3.23 × 10^?3 µg L^?1 for ofloxacin; 8.39 × 10^?3 µg L^?1 for ciprofloxacin; and 19.50 × 10^?3 µg L^?1 for enrofloxacin. The developed method was applied for the analysis of fluoroquinolone in milk, egg, fish, bovine, and chicken samples and the recoveries were obtained in the range 70–100%.     

Single-cell Protein and Xylitol Production by a Novel Yeast Strain <Emphasis Type="Italic">Candida intermedia</Emphasis> FL023 from Lignocellulosic Hydrolysates and Xylose

Yeasts are good candidates to utilize the hydrolysates of lignocellulose, the most abundant bioresource, for bioproducts. This study aimed to evaluate the efficiencies of single-cell protein (SCP) and xylitol production by a novel yeast strain, Candida intermedia FL023, from lignocellulosic hydrolysates and xylose. This strain efficiently assimilated hexose, pentose, and cellubiose for cell mass production with the crude protein content of 484.2 g kg^?1 dry cell mass. SCP was produced by strain FL023 using corncob hydrolysate and urea as the carbon and nitrogen sources with the dry cell mass productivity 0.86 g L^?1 h^?1 and the yield of 0.40 g g^?1 sugar. SCP was also produced using NaOH-pretreated Miscanthus sinensis straw and corn steep liquor as the carbon and nitrogen sources through simultaneous saccharification and fermentation with the dry cell productivity of 0.23 g L^?1 h^?1 and yield of 0.17 g g^?1 straw. C. intermedia FL023 was tolerant to 0.5 g L^?1 furfural, acetic acid, and syringaldehyde in xylitol fermentation and produced 45.7 g L^?1 xylitol from xylose with the productivity of 0.38 g L^?1 h^?1 and the yield of 0.57 g g^?1 xylose. This study provides feasible methods for feed and food additive production from the abundant lignocellulosic bioresources.     

A Flow-Based Analytical Procedure for Salbutamol Determination Exploiting Chemiluminescence in a Liquid-Core Waveguide

Abstract

Salbutamol is a bronchodilator whose use is restricted due to its anabolic effects. A flow-based procedure for salbutamol determination based on the inhibition of chemiluminescence of the luminol/hypochlorite system was developed. A flow cell constructed with a liquid-core waveguide was employed to constrain the emitted radiation, minimizing losses during transport to detector. Linear response was observed within 2.5 × 10^?6 and 1.0 × 10^?5 mol L^?1 with a detection limit estimated as 1 × 10^?7 mol L^?1 at the 99.7% confidence level. The coefficient of variation (n = 20), sampling rate, and luminol consumption per determination were estimated as 2.8%, 164 determinations h^?1, and 50 µg, respectively. Results for pharmaceutical samples were in agreement with those obtained by reference procedures at the 95% confidence level.     

Determination of ultratrace amounts of plutonium in high saline groundwater by inductively coupled plasma mass spectrometry

For determination of ultratrace amounts of plutonium in high saline groundwater, large-volume sampling and preconcentration are necessary. However, traditional co-precipitation methods, such as Fe(OH)₃, Ca(OH)₂–Mg(OH)₂ and hydroxide-carbonate co-precipitation, are unable to meet the requirements of preconcentration of the ultratrace plutonium in high saline groundwater. In this paper, the ultratrace plutonium in high saline groundwater was concentrated by sequential co-precipitation with MnO₂ and Fe(OH)₃, and purified by two-stage anion-exchange separation on Dowex1 × 4 resin column. Quadrupole ICP-MS was employed for the determination of ²³⁹Pu with ²⁴²Pu spiked. After co-precipitation and purification, the major matrix elements were significantly decreased to μg mL^?1 level and decontamination factor of uranium is better than 10⁶. The detection limit for ²³⁹Pu in 50 L high saline water is 2.1 × 10^?16 g L^?1. Three high saline fountain samples (total dissolved solids more than 20 g L^?1) from Dunhuang region of China were analyzed using this method. The concentrations of ²³⁹Pu in these samples were 0.48 ± 0.2 × 10^?15, 1.40 ± 0.10 × 10^?15 and 2.13 ± 0.21 × 10^?15 g L^?1 respectively. The recovery obtained for 7 pg of ²⁴²Pu spiked into real high saline-water samples was all above 70 %.     

Novel potentiometric sensor for the trace-level determination of Zn2+ based on a new nanographene/ion imprinted polymer composite

In this research, a new strategy for construction of a development potentiometric carbon paste Zn²⁺-ion selective electrode based on a novel nano-sensing layer is suggested. The proposed nano-sensing layer was prepared with the addition of a synthesised Zn²⁺-ion imprinted polymer nanoparticles ‘as an efficient sensing agent’ into the carbon paste matrix consisting of graphite powder, nanographene-composite ‘graphene nanosheets decorated with silver nanoparticles’ and 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ‘ an ionic liquid ’, as the conducting binder. Under the optimised experimental conditions, the suggested nanographene-composite potentiometric sensor presented a low detection limit of 1.93 × 10^?1 μg L^?1 and a linear analytical range from 2.62 × 10^?1 to 6.54 × 10⁵ μg L^?1 with an excellent Nernstian slope of 29.80 mV decade^?1. The proposed zinc selective sensor was successfully applied for the highly sensitive determination of trace amounts of Zn²⁺ in environmental and biological samples with satisfactory results.     

A novel strategy for selective detection of Ag+ based on the red-shift of emission wavelength of quantum dots

Selective determination of Ag(I) ion was accomplished based on the red-shift of the emission band of quantum dots (QDs). Under optimal conditions, a linear relationship does exist between the red-shift of the emission and the concentration of Ag(I) in the range from 1.0?×?10^?7 to 1.5?×?10^?5 mol L^?1, with a detection limit of 5.0?×?10^?8 mol L^?1. The method has been successfully applied to the determination of Ag(I) ion in water samples. The possible reaction mechanism was investigated by ultraviolet–visible absorption, fluorescence, Raman spectroscopies and by high resolution transmission electron microscopy. The results suggest that the red-shift in emission be attributed to the stabilization of a charge-transfer state, but not due to the aggregation induced by AgI(I) ion.     

Detection of trace nitrite in waters using a QDs-based chemiluminescence analysis system

In the present work, a novel flow-injection chemiluminescence method based on CdTe quantum dots (QDs) was developed for the determination of nitrite. Weak chemiluminescence (CL) signals were observed from a CdTe QDs–H₂O₂ system under basic conditions. The addition of a trace amount of hemoglobin (Hb) caused the CL from the CdTe QDs–H₂O₂ system to increase substantially. In the presence of nitrite, the ferrous Hb reacted with the nitrate to form ferric Hb and NO. The NO then bound to ferrous Hb to generate iron nitrosyl Hb. As a result, the CL signal from the CdTe QDs–H₂O₂–Hb system was quenched. Thus, a flow-injection CL analytical system for the determination of trace nitrite was established. Under optimum conditions, there was a good linear relationship between CL intensity and the concentration of nitrite in the range 1.0?×?10^?9 to 8.0?×?10^?7 mol L^?1 (R ²?=?0.9957). The limit of detection for nitrite using this system was 3.0?×?10^?10 mol L^?1 (S/N?=?3). This method was successfully applied to detect nitrite in water samples.

Photoluminescence investigation of MPA–ZnS QDs interaction with selenite ion

The interaction between water-soluble zinc sulfide quantum dots (ZnS QDs) and selenite ion was investigated by photoluminescence method. The water-soluble ZnS QDs were synthesized using a simple and fast procedure based on the co-precipitation of nanoparticles in an aqueous solution in the presence of 3-mercaptopropionic acid (MPA), as the capping agent. Fluorescence intensity for MPA–ZnS QDs, with a strong fluorescent emission at about 430 nm, decreased in the presence of selenite. The influence of the effective parameters including pH and temperature was investigated. The results showed that under the optimum conditions, the fluorescence intensity change of QDs was linearly proportional to the selenite concentration in the range 4.0 × 10^?5–7.2 × 10^?4 mol L^?1. Moreover, the quenching mechanism was discussed to be a static quenching procedure.     

Determination of Tyrosine in the Presence of Sodium Dodecyl Sulfate Using a Gold Nanoparticle Modified Carbon Paste Electrode

A carbon paste electrode modified with gold nanoparticles (AuMCPE) was used as a highly sensitive sensor for determination of Tyrosine (Tyr), in the presence of an anionic surfactant, sodium dodecyl sulfate (SDS), in aqueous solution. The measurements were carried out by using of differential pulse voltammetry (DPV), cyclic voltammetry (CV), amd chronocoulometry and chronoamperometry methods. The prepared electrode shows voltammetric responses with high sensitivity and selectivity for Tyr in the presence of SDS. The relationship between the oxidation peak current of Tyr and its concentration was obtained linearly and it was 1.0 × 10^?7 to 1.0 × 10^?5 M with a detection limit of 5.5 × 10^?8 M in the absence of SDS. On the other hand the oxidation peak current of Tyr increased significantly at AuMCPE in the presence of SDS and its detection limit was reduced to 2.7 × 10^?9 M. The proposed voltammetric approach was also applied to the determination of Tyr concentration in human serum.     

The Determination of Perphenazine by a New Simple Flow‐Injection Chemiluminescence Method

Abstract

A rapid and simple flow‐injection chemiluminescence (CL) method is described for the determination of perphenazine, which is based on the CL intensity that generated from the redox reaction of Ce (IV)-perphenazine in HNO₃ medium is proportional to the perphenazine concentration without any sensitizers. The proposed method allows the determination range within 1.0×10^?7–7.0 ×10^?5 g mL^?1 with a detection limit of 8.0×10^?8 g mL^?1, and it has been successfully applied to the determination of the perphenazine in pharmaceutical tablet compared well with the official method.     

A new sensitive and selective sensor for heavy metal ions based on tannin extracted from the skin of Punica granatum L

This article presents the development of a sensor made from a gold electrode and a receiving polymeric membrane based on tannin extracted from the skin of Punica granatum. L (pomegranate) for real-time detection of heavy metals in a hydrous environment. The basic principle of this device is the complexing (chelating) of metal ions through the adjacent hydroxyl groups contained in the chemical structures of the tannins. The electrochemical characterisation was performed by using electrochemical impedance spectroscopy and square wave voltammetry. Other morphological and structural analyses were performed by using Fourier transform infrared spectroscopy and atomic-force microscopy. The results obtained showed the high sensitivity of the developed device (detection limits of 6.35 × 10^?9 g L^?1 for Cu²⁺, 1.1 × 10^?8 g L^?1 for Cd²⁺ and 2 × 10^?7 g L^?1 for Pb²⁺) and the possibility of simultaneously detecting several heavy metals, each one in a highly selective manner with highly acceptable response time (48s).     

A Sensitive Flow Injection Fluorimetry for the Determination of Carbamazepine in Human Plasma

Abstract

A simple, sensitive, and specific flow injection fluorimetric method has been developed for the determination of carbamazepine (CBZ). The proposed method is based on use of a solid‐phase reactor containing lead dioxide for on‐line oxidization of CBZ into a strongly fluorescent compound in a medium of phosphoric acid. The product has a green‐yellow fluorescence at a maximum excitation wavelength of 355 nm and an emission wavelength of 478 nm. Under the optimum conditions, the fluorescence intensity is proportional to the concentration of CBZ ranging from 0.0005 to 4.000 µg mL^?1. The detection limit is 5.7×10^?5 µg mL^?1 (2.4×10^?10 mol L^?1) and the relative standard deviation is 1.4% at the sampling rate of 45 h^?1. The proposed method has been applied to clinical estimation of CBZ in real patients' plasma samples with the results compared with those obtained by HPLC method.     

Electrochemical determination of bisphenol A based on PHD/MWCNTs modified glassy carbon electrode

A novel electrochemical sensor for the determination of bisphenol A (BPA) was fabricated by block polyelectrolyte composite films, which composed of diblock polyelectrolyte poly (2-hydroxyethyl methacrylate)-b-poly (2-(dimethylamino) ethyl methacrylate) (PHEMA-b-PDMAEMA, noted as PHD in the later content) and multi-walled carbon nanotubes (MWCNTs). The tertiary amino groups of PDMAEMA can be protonated at physiological pH. The protonated PDMAEMA can thus interact with the negatively charged BPA through electrostatic attraction to increase the BPA sorption capacity and enhance the ability for highly sensitive detection of BPA. The PHD/MWCNTs composite films combine the electrocatalytic property of MWCNTs and the electrostatic attraction of protonated PHD. Because of the above-mentioned excellent property of the composite films, the PHD/MWCNTs/glassy carbon electrode exhibited good electrocatalytic activity to electrooxidation of BPA. The wide linear response range of the BPA sensor was from 4.56 × 10^?5 g L^?1 to 2.28 × 10^?2 g L^?1 with a lower detection limit of 2.28 × 10^?6 g L^?1 (S/N = 3) and high sensitivity 2442.86 μA L g^?1 cm^?2. The current reached the steady-state current with a shorter response time less than 4 s. The proposed method was successfully applied to determine BPA in real samples (PVC food package, milk, tap water and pond water) and satisfactory results were obtained. These results indicated that the block polyelectrolyte composite have potential applicability of the BPA sensor.     

Electroanalytical Characteristics of Lercanidipine and its Voltammetric Determination in Pharmaceuticals and Human Serum on Boron-Doped Diamond Electrode

The electrooxidative behavior and determination of lercanidipine (LRC) were investigated in aqueous acetonitrile medium at a boron-doped diamond electrode using voltammetric techniques. The LRC in selected supporting electrolyte presents a well-defined anodic response at 0.944 V, studied by the proposed method. The linear response was obtained in the ranges of 4 × 10^?6 to 2 × 10^?4 mmol L^?1 range in 0.5 mmol L^?1 sulfuric acid supporting electrolyte and 1 × 10^?5 to 8 × 10^?5 mmol L^?1 range in spiked serum sample for square wave voltammetric technique. No electroactive interferences from the excipients and endogenous substances were found in the pharmaceutical dosage form and in the biological sample, respectively.     

Chemiluminescence Determination of Organophosphorus Pesticides Chlorpyrifos in Vegetable

Abstract

A novel chemiluminescence method for the quantitative assay of the organophosphorus pesticide chlorpyrifos in vegetable samples is presented. The determination is based on the reaction of chlorpyrifos with luminol-H₂O₂ in alkaline medium with sodium chloride being enhancer. Under the optimum conditions, the increased CL intensity was proportional with the concentration of chlorpyrifos in the range of 1.0 × 10^?8 g · ml^?1 ? 1.0 × 10^?6 g · ml^?1 and the detection limit was 3.5 × 10^?9 g · ml^?1 (3σ). The relative standard is less than 3.9% for 5.0 × 10^?7g · ml^?1 chlorpyrifos (n = 7). This method has been successfully applied to the determination of chlorpyrifos residue in vegetable sample. Further study was focused on the mechanism of chlorpyrifos and the possible mechanism was proposed.     

Electrochemical Enzyme‐Linked Immunoassay for the Determination of Estriol Using Methyl Red as Substrate

Abstract

A new electrochemical substrate for horseradish peroxidase, methyl red, is reported. In this reaction system, horseradish peroxidase can catalyze the redox reaction of methyl red and H₂O₂. Methyl red exhibits a sensitive voltammetric peak at?0.51 V vs. Ag/AgCl reference electrode, the decrease of the peak current of methyl red is in proportion to the concentration of horseradish peroxidase (HRP). The linear range for determination of horseradish peroxidase is 5.0×10^?8～5.0×10^?7 g mL^?1 and the detection limit is 1.8×10^?8 g mL^?1. The relative standard deviation is 3.3% when 2.0×10^?7 g mL^?1 HRP was sequentially determined 11 times. A voltammetric enzyme‐linked immunoassay method for the determination of estriol was developed, based on this electrochemical system. The linear range for determination of estriol is 1.0～1000.0 ng mL^?1, and the detection limit is 0.33 ng mL^?1. The relative standard deviation for 11 parallel determinations with 200 ng mL^?1 estriol is 4.8%. Some pregnancy serum samples were analyzed with satisfactory results.