OCS表面活性剂在弱碱、无碱条件下的界面张力性能研究

研究了OCS表面活性剂中试产品在弱碱NaCO33及无碱条件下应用于不同油田原油的油-水界面张力特性。结果表明：对于大庆采油四厂原油，当表活剂浓度为0．1％-0．3％，Na2CO3浓度为0．6％-1．2％时，油-水界面张力可达到超低(-l0^-3mN／m数量级)；对于大庆采油二厂原油，当表面活性剂浓度为0．1％-0．3％，Na2CO3浓度为0．8％-1．4％时，油-水界面张力可达到超低；对于华北油田古-联原油，当表面活性剂浓度为0．2％，NaCO3浓度为0．6％-1．2％时，油-水界面张力可达到超低；对于胜利油田孤东采油厂原油，当表面活性剂浓度为0．2％，NaCO3浓度为0．8％-1．4％时，油-水界面张力可达到超低。在无碱条件下，对于大港油田枣园1256断块原油，当OCS表面活性剂浓度达到0．1％时，油-水界面张力即可达到超低；对于江苏油田原油，当OCS表面活性剂浓度在0．1％以上时，油-水界面张力均可以达到10^-2mN／m数量级。聚丙烯酰胺聚合物的加入对油-水超低界面张力的形成和稳定具有促进作用。     

正负离子混合表面活性剂双水相界面张力的研究

用旋转滴法测定了正负离子混合表面活性剂形成的双水相界面张力, 研究了双水相界面张力与表面活性剂的分子结构、正负离子表面活性剂的摩尔比、总浓度、外加无机盐及温度的关系. 结果表明, 双水相界面张力在一定正、负离子表面活性剂的摩尔比时属于超低界面张力范围. 观察到三种界面张力曲线类型, 第一类为摩尔比1:1 的两边的两条曲线, 界面张力随过剩表面活性剂组分的比例增加而降低; 第二类为一条跨过摩尔比1:1的马鞍型曲线; 第三类为位于摩尔比1:1的一边的一条马鞍型曲线. 界面张力曲线的类型主要取决于表面活性剂的分子结构, 包括亲水基类型、疏水链长度及对称性.     

磷酸对TiO2纳米粒子光催化剂的改性

通过浸渍过程实现了磷酸对溶胶水热法合成的锐钛矿相TiO2纳米粒子的改性.重点研究了磷酸修饰对纳米锐钛矿相TiO2的热稳定性及光催化活性的影响.结果表明,磷酸修饰显著地提高了纳米锐钛矿相TiO2热稳定性,甚至经过800℃热处理后仍然具有以锐钛矿相为主的相组成.在光催化降解罗丹明B(RhB)过程中经过700℃热处理的磷酸修饰的样品表现出了优于商品P25-TiO2的活性.     

Fabrication of TiO2 Grating with Composites of Azobenzene Polymer and TiO2 Nanoparticles

We have used the formation of surface relief gratings (SRG) on azobenzene polymers to manipulate TiO₂ nanoparticles and to fabricate TiO₂ nanoparticle gratings. Suspensions of an azobenzene polymer (PDO3) and TiO₂ were used to spin coat thin films on glass slide substrates. By interfering coherent light from an Argon laser on the surface of the PDO3‐TiO₂ composite films, SRGs were fabricated. Atomic force microscopic images of the SRGs show TiO₂ nanoparticles dispersed throughout the sample, and in particular, at the peaks of the SRG after oxygen plasma treatment. The lateral forces acting on the azobenzene polymer during the SRG fabrication drag the TiO₂ nanoparticles. These results indicated that it is feasible to create TiO₂ nanoparticle gratings with the composites.     

NaCl对烷基苯磺酸盐Gemini表面活性剂水溶液性质的影响

采用旋滴法测定了烷基苯磺酸盐Gemini表面活性剂Ia水溶液与正庚烷的界面张力,用超微电极循环伏安法测定了水溶液中Ia的胶束扩散系数.结果发现,NaCl的加入能够使界面张力降低2倍左右,使Ia的胶束扩散系数变大;Ia浓度增大,胶束扩散系数变小,而NaCl浓度增大,胶束扩散系数变大.这些变化说明NaCI的加入使得Ia胶束大小发生了变化.这是由于NaCl的加入降低了Ia离子头基之间的静电斥力,使得Ia分子排列更加紧密,更有效降低了油水的界面张力,使胶束形状变小;同时胶束表面电荷得到中和,胶束的静电斥力相应减小,胶束流动性相应增加,从而表现出较大的胶柬扩散系数.     

载有C60的TiO2纳米粒子光催化活性

以水溶性C₆₀和TiO₂粒子为前驱体,采用水热法制备了载有C₆₀的锐钛矿型TiO₂纳米粒子。应用X射线衍射、透射电子显微镜、红外光谱、紫外-可见漫反射光谱、荧光光谱对产物进行了表征。以对-硝基苯酚为模型污染物研究了产物的光催化活性,结果表明适量负载C₆₀可以提高TiO₂纳米粒子的光催化活性,C₆₀起着传输电子、促进TiO₂光生载流子分离的作用,且经7次循环使用后对-硝基苯酚的降解效率仍能达到74%。讨论了载有C₆₀的TiO₂纳米粒子光催化降解对-硝基苯酚的机理。     

Study on the Interfacial Tensions Between Oils and Alkylbenzene Sulfonate Gemini Surfactant Solutions

Interfacial tensions (IFT) of five alkylbenzene sulfonate Gemini surfactants Ia, Ib, Ic, Id, and Ie at different oils/water systems were measured by a spinning drop interfacial tensiometer. And critical micelle concentration (CMC), the interfacial tension at CMC (γ_CMC), maximum interfacial excess concentration (Γ _max) and the surface area per molecule (A_min) were calculated. The results indicated that the CMC values determined with interfacial tension method were lower than those determined with surface tension method. And γ_CMC for Ie is larger than that for Ia, Ib, Ic, and Id. In addition, the effects of temperature and hydrophobic chains on dynamic IFT were also studied. With the increment of temperature, dynamic IFT is easier to reach a stable value. However, with the increment of hydrophobic chains, dynamic IFT is more difficult to reach a stable value. Each Gemini surfactant produces a minimum IFT when measured against a different n-alkane.     

油/水界面张力的影响因素及无机盐对油水铺展的影响

讨论不同有机相与水形成的油/水界面处水/气、油/气及油/水3个界面张力的影响因素及相对大小。重点讨论了加入无机盐对作用于透镜状油滴上的3个界面张力的影响,总结出基本的规律并进行了实验验证。     

水热法合成纳米TiO2及其在Grtzel电池中的应用

By varying the hydrolysis and hydrothermal processing parameters in preparing TiO2 nanoparticles different sizes of TiO2 nanoparticles are obtained.(1) At higher autoclaving temperature,lower pH and longer autoclaving period,larger sizes of TiO2 nanoparticles are prepared.(2) The nanoporous electrodes made from sintering smaller TiO2 nanoparticles show relatively poor IPCE and low absorption in UV Vis spectrum,(3) Higher IPCE can be achieved with TiO2 nanoporous electrodes made from sintering larger TiO2 nanoparticles.These electrodes are suitable for studying behavior of the photoelectrochemistry of dye sensitized nanoporous electrodes.     

疏水缔合聚丙烯酰胺与双子表面活性剂的相互作用

制备了一种脂肪酸酯双磺酸盐型双子表面活性剂, 利用粘度法、界面张力法和原子力显微镜研究了疏水缔合聚丙烯酰胺与双子表面活性剂在溶液中的相互作用. 实验结果表明: 疏水缔合聚丙烯酰胺在溶液中能够通过自组装形成疏水微区并发展成网络结构, 疏水微区与表面活性剂在溶液中能形成混合胶束; 当一定量的表面活性剂加入时, 对疏水缔合聚丙烯酰胺的自组装起促进作用, 而过多双子表面活性剂的加入又会对聚合物分子的自组装起抑制作用, 从而显著影响疏水缔合聚丙烯酰胺的溶液性质, 随着表面活性剂浓度的增加, 聚合物溶液粘度先增加、再降低; 同时, 疏水缔合聚丙烯酰胺对双子表面活性剂的界面性能也有较大影响, 聚合物的加入使双子表面活性剂降低油/水界面张力的能力下降, 油/水界面张力达到平衡所需时间延长.     

Comparison of CO2 Reduction Performance with NH3 and H2O between Cu/TiO2 and Pd/TiO2

The aim of this study is to clarify the effect of doped metal type on CO₂ reduction characteristics of TiO₂ with NH₃ and H₂O. Cu and Pd have been selected as dopants for TiO₂. In addition, the impact of molar ratio of CO₂ to reductants NH₃ and H₂O has been investigated. A TiO₂ photocatalyst was prepared by a sol-gel and dip-coating process, and then doped with Cu or Pd fine particles by using the pulse arc plasma gun method. The prepared Cu/TiO₂ film and Pd/TiO₂ film were characterized by SEM, EPMA, TEM, STEM, EDX, EDS and EELS. This study also has investigated the performance of CO₂ reduction under the illumination condition of Xe lamp with or without ultraviolet (UV) light. As a result, it is revealed that the CO₂ reduction performance with Cu/TiO₂ under the illumination condition of Xe lamp with UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:1:1 while that without UV light is the highest when the molar ratio of CO₂/NH₃/H₂O = 1:0.5:0.5. It is revealed that the CO₂ reduction performance of Pd/TiO₂ is the highest for the molar ratio of CO₂/NH₃/H₂O = 1:1:1 no matter the used Xe lamp was with or without UV light. The molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp with UV light was 10.2 μmol/g, while that for Pd/TiO₂ was 5.5 μmol/g. Meanwhile, the molar quantity of CO per unit weight of photocatalyst for Cu/TiO₂ produced under the illumination condition of Xe lamp without UV light was 2.5 μmol/g, while that for Pd/TiO₂ was 3.5 μmol/g. This study has concluded that Cu/TiO₂ is superior to Pd/TiO₂ from the viewpoint of the molar quantity of CO per unit weight of photocatalyst as well as the quantum efficiency.     

Thermal behaviour of high surface area V2O5/TiO2 catalysts

Thermal analysis (TG and DTA) was employed for the characterization of V₂O₅/TiO₂ catalysts supported on high surface area TiO₂. The results obtained are consistent with a uniform spreading of vanadium oxide on TiO₂ surface for V₂O₅ content less than 15% by weight.The presence of V₂O₅ on the surface of TiO₂ affects the anatase-rutile phase transition lowering the temperature at which it occurs.DTA measurements, performed on catalysts after many months from the preparation, show the appearance of an exothermic peak in the range 280°–340°C. This signal has been related to the oxidation of V(IV) to V(V) on the catalyst surface.Catalysts characterization, performed by chemical analysis and FT-IR spectroscopy, has confirmed this interpretation.It has been suggested that a slow modification of the catalyst occurs, leading to an increase of the V(IV) content during the time.

---

Zusammenfassung Zur Charakterisierung von V₂O₅/TiO₂-Katalysatoren auf hochoberflächigem TiO₂ Trägermaterial wurde die Thermoanalyse (TG und DTA) angewendet. Für einen V₂O₅-Gehalt von weniger als 15 Gew.% entsprechen die erhaltenen Ergebnisse einer gleichmäßigen Verteilung des Vanadiumoxides an der TiO₂-Oberfläche.Die Gegenwart von V₂O₅ an der Oberfläche von TiO₂ beeinflußt die Anatas-Rutil-Phasenumwandlung, indem sie die zugehörige Temperatur verringert.DTA-Messungen an Katalysatoren mehrere Monate nach ihrer Herstellung zeigten das Auftreten eines exothermen Peaks im Bereich 280°–340°C. Dieses Signal wurde der Oxidation von V(IV) zu V(V) an der Katalysatoroberfläche zugeschrieben.Diese Interpretation konnte durch eine Charakterisierung des Katalysatoren durch chemische Analyse und FT-IR-Spektroskopie bestätigt werden.Es wurde angedeutet, daß der Katalysator mit der Zeit einer langsamen Modifikation unterliegt, die zu einem Ansteigen des V(IV)-Gehaltes führt.

     

Patterning Effect of a Sol-Gel TiO2 Overlayer on the Photocatalytic Activity of a TiO2/SnO2 Bilayer-Type Photocatalyst

TiO₂ films with a thickness of 75 ± 5 nm (anatase) were formed on SnO₂-film (580 ± 80 nm) coated soda-lime glass substrates (SnO₂/SL-glass) by a sol-gel method. Although the photocatalytic activity for CH₃CHO oxidation (_ex > 300 nm) significantly exceeded that of a standard TiO₂/quartz sample, it decayed with illumination time (t) at t > 0.75 h. Stripes of anatase TiO₂ films of 40 nm in thickness and 1 mm in width were prepared on the SnO₂/SL-glass substrate in a 1-mm pitch by photolysis of an organically modified sol-gel film. The TiO₂ patterning further increased the photocatalytic activity by a factor of 4.1 as compared to the non-patterned sample, and it was also maintained at 0 < t < 2 h. The flat band potentials of the TiO₂ and SnO₂ films are determined to be –0.34 and +0.07 V (vs. SHE), respectively, at pH = 7 by the Mott-Schottky plots. On the basis of the results, the outstanding patterning effects could be rationalized in terms of the vectorial charge separation at the interface between TiO₂ and SnO₂.     

Interfacial tension between water and high pressure CO2 in the presence of hydrocarbon surfactants

Interfacial tension of water–CO₂ interface was measured by pendant drop method in the presence of a surfactant of various concentrations. The surfactants used were three surfynols which are non-ionic blanched hydrocarbon with different length of the alkyl side chain. Prior to the interfacial tension measurements, the solubility of the surfynols in CO₂ were determined from cloud point method. The measured interfacial tensions indicated that an addition of small amount surfactant did reduce the interfacial tension. The interfacial activities of surfactants were evaluated from the slope of the interfacial tension reduction curve against the surfactant concentration and rationalized in terms of the molecular natures such as hydrophobic alkyl chain length.     

Centrally Coordinated Cobalt Porphyrin Monolayers on the Surface of TiO2 Nanoparticles

Aminopropyltrimethoxysilane (APTS) on the surface of TiO₂ nanoparticles was used to bind cobalt(II) 5,10,15,20-tetra-(4-trimethylaminophenyl)porphyrin iodide (CoTAPPI). The binding involved coordination of amino-group in the APTS to cobalt(II) ion in the center of the porphyrin. The absorption and fluorescence spectra of the products showed that there existed the electron transfer among TiO₂, APTS, and CoTAPPI. The polarized fluorescence spectra were used to evaluate the coordination constants of the porphyrin and APTS. The molecular geometry and binding energy of the TiO₂-APTS-CoTAPPI assembly were calculated with the molecular mechanics approach (MM2).     

Structure of TiO2 in TiO2-SiO2 prepared by a complexing agent-assisted sol-gel procedure

Many types of TiO₂-SiO₂ (Ti:Si=50:50 mol%) were prepared by the sol-gel procedure with and without 2-methyl-2, 4-pentanediol (MPD) as an organic ligand. The effect of MPD on the gel structure and the properties of the TiO₂ crystals were studied by XRD and raman spectroscopy, and the effect of the sol standing time on the properties of the TiO₂ crystals were also studied by XRD spectroscopy. In the gels with MPD, anatase of TiO₂ appeared at approximately 580°C, and the crystal structures were similar despite the difference in the gel preparation procedure. The titania gels with MPD were presumed to be dispersed in the silica gel matrix without any Ti-O-Si bond. In the presence of MPD, the formation of titania gels is controlled and the specified TiO₂ crystal is produced.     

ASP复合驱油体系瞬时界面张力的研究

以胜利油田孤岛试验区原油为油相,用正交试验筛选了碱/天然混合羧酸盐/聚合物驱油体系,讨论了各组分对ASP复合驱油体系油水瞬时界面张力的影响,并探讨了各组分间的相互作用机理及其在油水界面的吸附机理。     

Effect of polyaniline as a surface modifier of TiO2 nanoparticles on the properties of polyvinyl chloride/TiO2 nanocomposites

Surface of TiO2 nanoparticles was modified with the in situ chemical oxidative polymerization of aniline. Polyaniline modified TiO2 nanoparticles (PANI-TiO2 ) were characterized with the FT-IR, XRD, SEM and TEM techniques. Results confirmed that PANI was grafted successfully on the surface of TiO2 nanoparticles, therefore agglomeration of nanoparticles decreased dramatically. Polyvinyl chloride nanocomposites filled with 1 wt% 5 wt% of PANI-TiO2 and TiO2 nanoparticles were prepared via the solution blending method. PVC nanocomposites were analyzed with FT-IR, XRD, SEM, TG/DTA, DSC and tensile test techniques. Effect of PANI as surface modifier of nanoparticles was discussed according to the final properties of PVC nanocomposites. Results demonstrated that deposition of PANI on the surface of TiO2 nanoparticles improved the interfacial adhesion between the constituents of nanocomposites, which resulted in better dispersion of nanoparticles in the PVC matrix. Also PVC/PANI-TiO2 nanocomposites showed higher thermal resistance, tensile strength and Young’s modulus compared to those of unfilled PVC and PVC/TiO2 nanocomposites.     

异丁醇-水-硝基乙烷体系中的双因素自耦合界面不稳定现象

指导了发生在异丁醇、硝基乙烷和水三组分两相体系中的多因素复合界面不稳定现象，文中通过对一个滴加在异丁醇水溶液表面的硝基乙烷液滴的运动特征的分析，揭示了该现象的规律，在体系趋于热力学平衡的过程中，硝基乙烷液滴先表现出周期性的振荡运动，然后转变为螺旋线和圆周运动，提出了一个溶质迁移和相间溶解的双因素自耦合机理，认为该现象的根本起因是表面活性剂溶质相间迁移所导致的溶质Ｍａｒａｎｇｎｉ效应，但由于丁醇的相     

Novel Surfactant for the Reduction of CO2/Brine Interfacial Tension

The synthesis of novel CO₂ philic surfactant using maleic anhydride and dipropylene tertiary butyl alcohol is reported. The synthesis involved the esterification of maleic anhydride to produce bis(2-(2-(tert-butoxy)propoxy)propyl) maleate and subsequent sulfonation of the esterified product. Para toluene sulfonic acid was employed as catalyst for the esterification reaction. The esterification reaction was optimized for the maximum yield of 98% of bis(2-(2-(tert-butoxy)propoxy)propyl) maleate. The esterification reaction kinetics employing heterogeneous catalyst were also studied. Although this is a bimolecular reaction, a first order reaction kinetics with respect to acid has been observed. The activation energy was found to be 58.71 kJ/mol. The diester was followed by the sulfonation process and a yield of 85% of surfactant was achieved. The synthesized surfactant successfully lowered down the IFT between CO_2/brine to 1.93 mN/m. This surfactant has a great potential to be used for CO₂-EOR applications.