Low-voltage blue-phase liquid crystal display with single-penetration electrodes

A blue-phase liquid crystal display (BPLCD) with single–penetration (S-P) electrodes is proposed to reduce the operating voltage. X-shape inclined-electric field is induced by the S-P electrodes with 2 ~ 3 μm height, which can lower the operating voltage by ~45%, and improve the transmittance compared with BPLCD with conventional in-plane electrodes. Moreover, the wide viewing angle and very small image distortion index can be obtained in this structure with a half-wave biaxial film. The proposed structure shows simple etching control and easy one-drop filling process of blue-phase liquid crystal compared with dual-convex-penetration electrodes.     

Low-gamma shift asymmetrical double-side blue-phase liquid crystal display

ABSTRACT

A single-domain blue-phase liquid crystal display (BPLCD), which has asymmetrical double-side electrode structure, is proposed to reduce gamma shift. Firstly, the electro-optical curve and gamma shift of the proposed BPLCD are discussed under the comparison with conventional in-plane switching (IPS) BPLCD. And then, its gamma shift is investigated under various conditions. Compared with the conventional IPS-BPLCD, the operating voltage can be reduced by ~31%, and the transmittance is increased by ~6%. The indistinguishable gamma shift can be obtained under various electrodes’ sizes, when the cell gap is appropriate. The results also indicate that if the electrodes’ height and Kerr constant of BPLC increase, the operating voltage can be further reduced (only 9.6 V in this work), and the gamma shift almost do not change. Moreover, a certain misalignment between the top and bottom glasses are permitted, which is good for reducing the fabrication difficulty. In terms of viewing angle, the proposed BPLCD has an average contrast ratio of ~5000:1, and the gamma shifts at full viewing angles are all indistinguishable.     

Low gamma shift blue-phase liquid crystal display with electric field induced multi-domain electrode structure

ABSTRACT

To reduce the gamma shift of blue-phase liquid crystal display (BPLCD), the multi-domain electrode structure with four sub-electrodes is proposed. The effects of electrodes’ parameters on electro-optical curve and gamma shift are calculated, and the gamma shift and contrast ratio at full viewing-cone are also investigated. For the proposed protrusion BPLCD, the operating voltage is reduced by ~73%, and the transmittance is increased by ~20% compared with the conventional in-plane switching BPLCD. The results also show that the off-axis image distortion index can be reduced from 0.4318 to 0.0875 at the polar angle of 60°, and it works well under various electrodes’ sizes. Moreover, the indistinguishable gamma shift can be obtained at full viewing-cone for the proposed BPLCD, and the uniform light distribution and high contrast ratio can be obtained as well.     

Blue-phase liquid crystal display with high dielectric material

A blue-phase liquid crystal display (BPLCD) with low operating voltage and high transmittance is demonstrated by using a high dielectric material, which is used as an insulation layer or protrusion fixed on the pixel and common electrodes in in-plane switching (IPS) mode. The operating voltage is reduced to about 14 V and the transmittance is improved for the BPLCD with high dielectric constant protrusion. Compared with the conventional protrusion electrode structure, the proposed protrusion can make manufacturing process simple and easy because the electrode has no complex shape. The results will be significant in designing optimal BPLCDs.     

Low voltage blue-phase liquid crystal display with insulating protrusion sandwiched between dual-layer electrodes

In order to lower the operating voltage of blue-phase liquid crystal display (BPLCD), a BPLCD with insulating protrusion, which is sandwiched between dual-layer electrodes, is proposed. There are four electrodes in this structure; thus, we investigate different driving methods to find a proper driving method. The effect of protrusion’s dielectric constant on operating voltage of the proposed BPLCD is explored under various electrodes’ parameters. As a result, the operating voltage of the proposed BPLCD with protrusion’s dielectric constant of 1,000 is 9.8 V, which is reduced by ~ 4.67× compared with that of conventional in-plane switching (IPS) BPLCD (45.8 V). Moreover, the zigzag electrode structure is adopted to reduce the large off-axis image distortion index. Besides, the azimuth distortion index is defined to describe the gamma shift between the minimum and maximum gamma shift curves at a certain polar angle. The results show that the off-axis image distortion index can be reduced to 0.0834, the azimuth distortion index is 0.0810 and the viewing cone of contrast ratio larger than 1,000:1 is over 50ºas the zigzag proposed BPLCD is used.     

Low voltage and high transmittance transflective blue-phase liquid crystal display with opposite polar electrodes

A single-cell-gap transflective polymer-stabilised blue-phase liquid crystal display with opposite polar pixel electrodes on an etched substrate is proposed. In the proposed structure, the space between common electrodes is adopted as transmissive region, and the space above the common electrode is adopted as reflective region. By optimising the electrode parameters of the transmissive and reflective regions, well-matched voltage-dependent transmittance and reflectance curves can be obtained. In addition, the device has good performances of low operating voltage (~3.2 V), high optical efficiency and a wide viewing angle.     

Blue-phase liquid crystal display with insulating protrusion

In order to lower the saturation voltage and enhance the transmittance of in-plane switching blue-phase liquid crystal display (IPS-BPLCD), IPS-BPLCD with insulating protrusion is proposed. The single-protrusion (only set on the top of pixel electrode) and double-protrusion (set on the top of pixel and common electrodes) structures are investigated in this work. The potential distribution changes when the protrusion is used. There is a thicker transverse electric field in BPLC range, because the stronger electric field at the edges of the electrodes is decentralised into BPLC range. As a result, the saturation voltage is reduced from 36.3 V to 28.9 V when the double-protrusion structure is used, and transmittance is increased by ~20%. The contrast ratio is larger than 1000:1 in 60° viewing cone using a half-wave biaxial film. Both single-protrusion and double-protrusion structures have the uniform gamma curves at large oblique viewing angles. Moreover, the off-axis image distortion index is 0.1590 at 60º polar angle when zigzag electrodes are used.     

Single electro-optic curve for RGB colours in blue-phase liquid crystal display

The double-layer penetration electrode structure is proposed to obtain the low-operating voltage blue-phase liquid crystal display (BPLCD) with single electro-optic curve for red-green-blue (RGB) colours in every pixel, which is more suitable for the field-sequential-colour display. The different influences of electrode’s parameters and driving methods on the electro-optical properties of the proposed BPLCD are investigated. The results demonstrate that the operating voltage can be reduced from 53.80 V to 23.00 V for red colour. Besides, the coincident voltage-dependent transmittance curves for RGB colours are obtained by adjusting the applied voltage of sub-electrode. Thus, RGB lights can pass through every pixel with single electro-optic curve, which is good for resolution enhancement and single gamma driving. Besides, the maximum gamma shift of the proposed BPLCD is less than 0.1099 at 60° polar angle for the red colour, and the gamma shift difference between red and blue colours is only 0.0542. If the high dielectric constant material is used as the protrusion, the operating voltage can be further decreased, which is close to that of the BPLCD with wall-shaped electrode structure.     

Reflective blue phase liquid crystal displays with double-side concave-curved electrodes

Reflective blue phase liquid crystal display (BPLCD) is a promising candidate for field sequential colour displays with reflective liquid-crystal-on-silicon (LCoS). However, the issue of high operation voltage still hinders its widespread applications. We propose a reflective BPLCD with double-side concave-curved electrode and research its operation voltage and electro-optic characteristics in simulation, which is compared to the transmissive mode. The effect of double-side electrodes on horizontal electric field and operation voltage is analysed. The improvement of concave-curved electrodes on reflectance is discussed. A reflective BPLCD has two times the optical path difference compared to the transmissive mode. By using double-side concave-curved electrodes, the reflectance increased by 23% and the operation voltage reduced by 32% compared to the traditional in-plane switching mode. This work enables BPLC to be integrated with reflective LCoS.     

A transflective polymer-stabilised blue-phase liquid display with partitioned wall-shaped electrodes

A transflective polymer-stabilised blue-phase liquid crystal display (BP-LCD) with partitioned wall-shaped electrodes is proposed. The etched polymer layer contributes to balance the optical phase retardation between transmissive (T) and reflective (R) regions. The partitioned wall-shaped electrodes generate uniform and horizontal fields throughout the entire LC layer to induce isotropic-to-anisotropic transition in the blue-phase liquid crystal medium through Kerr effect. Consequently, the accumulated phase retardation along beam path is large, resulting in reasonable low operation voltage and high transmittance both in T and R regions. This approach enables the BP-LCD to be addressed by amorphous silicon thin-film transistors. Moreover, it exhibits wide viewing angle and a well-matched gamma curve.     

Continuous viewing angle controllable patterned vertical alignment liquid crystal display

A continuous viewing angle switchable patterned vertical alignment liquid crystal display (PVA-LCD) with circle polarisers is proposed. In wide viewing angle (WVA) mode, the viewing cone with contrast ratio larger than 1000:1 is extended to 50° and the contrast ratio larger than 100:1 is extended to 80°. Meanwhile, the viewing cone with contrast ratio more than 10:1 is limited to 40° in all direction for narrow viewing angle (NVA) mode. The viewing angle of the display can be controlled by applying a bias voltage on the common electrode. With the increasing bias voltage, the viewing angle cone with contrast ratio more than 10:1 can be changed from 40° to 20°. The proposed PVA-LCD has high transmittance (~93%) under the circle polarisers because the dead zone in the normal PVA-LCD with linear polarisers is eliminated.     

A transflective blue-phase liquid crystal display with alternate electrodes

A transflective polymer-stabilised blue-phase liquid crystal display (BP-LCD) with alternate electrodes is proposed. The alternate electrodes are composed of right triangle electrodes and slanted electrodes. To balance the optical phase retardation between the transmissive (T) and reflective (R) regions, the legs of the right triangle electrodes in the T region generate uniform horizontal electric field, the hypotenuses of the right triangle electrodes and slanted electrodes in the R region generate uniform oblique electric field. As result, the T and R regions obtain the same optical phase retardation. This display exhibits reasonably high transmittance, low operating voltage, wide viewing angle and well-matched voltage-dependent transmittance and reflectance curves.     

Mixed-field-switching liquid crystal mode using in-plane and fringe fields self-adjusted by bottom floating electrode for transmittance enhancement

We demonstrate a liquid crystal (LC) mode switched by mixed electric fields of in-plane and fringe fields, which are self-adjusted by adopting a bottom floating electrode for enhanced electro-optical properties. In our LC mode structure, conventional in-plane switching (IPS) electrodes are formed as pixel electrodes and common electrodes on an insulating layer and floating electrodes that are patterned per the sub-pixels. When the areas of the pixel and common electrodes are identical, the voltage of the bottom floating electrode is spontaneously determined to be half the value of the pixel voltage, which ideally generates symmetric fringe fields with both pixel and common electrodes. Due to the in-plane fields additionally generated between the pixel and common electrodes, the proposed LC structure operates by mixed-field switching (MFS), which shows higher transmittance than fringe-field switching (FFS) and IPS LC modes. Transmittance of the conventional FFS and IPS LC modes is highly sensitive to the in-plane electrode’s width (w) and spacing (l) condition, but the proposed MFS LC mode shows good transmittance without degradation with large variations of the in-plane electrode’s spacing-to-width ratio (l/w).     

Viewing angle controllable fringe and in-plane switching vertical alignment LCD

A viewing angle controllable fringe and in-plane switching vertical alignment liquid crystal display (LCD) structure has been proposed. To realise the change from wide viewing angle (WVA) to narrow viewing angle (NVA) in a single LCD panel, the bias voltage is applied on the common electrode, and NVA can decreases with the increasing bias voltage. In WVA mode, the viewing angle cone (contrast ratio larger than 1000:1) is almost 70° and the contrast ratio is larger than 100:1 in arbitrary azimuthal directions. In NVA mode, the viewing angle cone (10:1) can continuously and uniformly change from 40° to 20°.     

A transflective and viewing angle controllable blue-phase liquid crystal display

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-side in-plane switching (DS-IPS) electrode structure is proposed. This structure shows the transflective characteristics because the bottom electrodes are made by aluminium material. For transflective displays, it exhibits a well-matched voltage-dependent transmission and reflection curves through designing the width and gap of the top electrodes. When a bias voltage is applied on the top electrodes, it exhibits as a good viewing angle controllable display.     

Optimisation of blue-phase liquid crystal with protrusion

The optimised structures of blue-phase liquid crystal display (BPLCD) with various protrusions were discussed in this article. The voltage-dependent transmittances for the cell with four protrusion shapes, wall-shaped electrode, trapezoid electrode, double penetration electrode and elliptical electrode, are simulated. The electrode gap and width and protrusion height’s effects on the optimised cell gap and the corresponding operating voltage are calculated. The optimised cell has the lowest operating voltage and relative high transmittance. The results are significant on design BPLCD with low operating voltage.     

Biaxial film design for full-colour,wide-view and high-contrast blue phase liquid crystal displays

To achieve full-colour, wide-view and high-contrast blue phase liquid crystal display (BPLCD), the compensated biaxial film is analysed in this paper. The dispersion of birefringence affects the light leakage of dark state and then affects the viewing angle and the contrast ratio at large polar viewing angle. Iso-transmission of dark state for BPLCD without compensational film, with conventional or wide-band biaxial film, is simulated. The simulated results show that the wide-band biaxial film is good for obtaining a BPLCD with excellent viewing angle and high-contrast ratio.     

Wide-viewing-angle switchable image splitter obtained using varied-line-spacing H-PDLC Bragg grating

We propose the use of a varied-line-spacing (VLS) holographic polymer-dispersed liquid crystal (H-PDLC) Bragg grating as a switchable image splitter to generate a compatible three-dimensional (3D) stereogram and to increase the viewing angle of the observer. To fabricate the VLS grating, a cylindrical lens is adopted to form a cylindrical wave, which interferes with a plane wave, generating an H-PDLC grating with a continuously varying period. The proposed holographic optical element (HOE)-based image splitter comprises two VLS H-PDLC gratings. It can be attached on a designed pattern, with two rectangles taking the place of conventional liquid crystal display panel pixels, and can separate them into right and left viewing fields with a wider range. Experimental results show that the movement of the eyes of the observer can reach 37.6 mm. A theoretical simulation indicates that a shorter focal length of the cylindrical lens can yield a larger movement range. Switching between two-dimensional and 3D modes can be performed by applying an external alternating-current voltage at ~80 V. The contrast ratio of the diffracted images induced by crosstalk is greater than 60%, which indicates the feasibility of the proposed HOE for 3D image splitting.     

A liquid crystal cell with double-side protrusion electrodes for fast response and low-voltage operation

We propose a homogeneously aligned liquid crystal (LC) cell with double-side protrusion electrodes for fast response and low-voltage operation. In the proposed device, both the bottom and top substrates have pixel electrodes to generate the fringe electric field. Because the penetration depth of the electric field is increased owing to the protrusion electrodes, the operating voltage is very low and the turn-on time is dramatically reduced compared with the conventional in-plane switching (IPS) mode. Moreover, LC molecules anchored strongly to the penetrated protrusion electrodes on both substrates exert a strong restoring force, resulting in a fast turn-off time. We found that the total response time of the LC cell with the proposed structure is three times faster than that of the conventional IPS mode.     

High-transmittance polymer-stabilised blue-phase liquid crystal display with double-sided protrusion electrodes

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-sided protrusion (DSP) electrodes structure is proposed. The oblique electric field between the protrusion electrodes inside both top and bottom glass substrates can induce more isotropic-to-anisotropic transition in the polymer-stabilised blue-phase liquid crystal (PS-BPLC) medium through Kerr effect than using the in-plane switching electrode. For the same electrode width, spacing and cell gap, the transmittance of PSBP-LCD with the DSP electrodes is ～29% higher than that using the IPS electrode.