Nanometer-sized alumina coated with chromotropic acid as solid phase metal extractant from environmental samples and determination by inductively coupled plasma atomic emission spectrometry

A method for solid phase extraction of trace metals such as Cd²⁺, Cr⁶⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, Pb²⁺ and Zn²⁺ using nanometer-sized alumina coated with chromotropic acid prior to determination by inductively coupled plasma atomic emission spectrometry (ICP-AES) has been developed. Various influencing parameters on the separation and preconcentration of trace metals, pH, flow rate, sample volume, amount of adsorbent, concentration of eluent and sorption kinetics have been studied. The detection limits for Cd²⁺, Cr⁶⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni²⁺, Pb²⁺ and Zn²⁺ were found to be 0.14, 0.62, 0.22, 0.54, 0.27, 0.28, 0.53 and 0.38 ng ml^− 1, respectively. The adsorption capacity of the solid phase adsorption material is 10.3, 11.3, 14.5, 16.4, 15.1, 11.7, 15.4 and 16.8 mg g^− 1 for Cd²⁺, Cr⁶⁺, Cu²⁺, Fe³⁺, Mn²⁺, Ni^2+, Pb²⁺ and Zn²⁺, respectively. The preconcentration factor was obtained in the range of 50-100 for all studied metal ions. Coexisting ions over a high concentration range have not shown any significant effects on the determination of aforesaid metal ions. The accuracy of the proposed method was tested by standard reference materials (NIST 1643e: water, NIST 1573a: tomato leaves and NIST 1568a rice flour) and natural waters and the results obtained were in good agreement with the certified values.     

Synthesis and Chelating Properties of Polystyrene Supported Schiff Base (N,N′-disalicylidenepropylenetriamine) Resin Toward Some Divalent Metal Ions

A new polystyrene-supported Schiff base resin, N,N-bis(salicylidenepropylenetriamine)- aminomethyl polystyrene, has been synthesized through a reaction between the commercially available 4-chloromethyl polystyrene polymer and the Schiff base, N,N′-disalicylidenepropylenetriamine. The chelation behavior of this resin toward the divalent metal ions Cu^{2 +}, Ni^{2 +}, Zn^{2 +}, and Pb^{2 +} in aqueous solutions was investigated. Batch equilibration experiments were carried out as a function of contact time, pH, amount of metal-ion, polymer mass, and temperature. The amount of metal-ion uptake of the polymers was determined by using atomic absorption spectrometry (AAS). Results of the study revealed that the resin exhibited higher capacities and a more pronounced adsorption toward Cu^{2 +} and that the metal-ion uptake follows the order: Cu^{2 +} > Zn ^{2 +} > Ni^{2 +} > Pb²⁺. The adsorption and binding capacity of the resin toward the various metal ions investigated are discussed.     

Preconcentration and Determination of Trace Amounts of Heavy Metals in Water Samples Using Membrane Disk and Flame Atomic Absorption Spectrometry

A fast and simple method for preconcentration of Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋ from natural water samples was developed. The metal ions were complexed with sodium diethyldithiocarbamate （Na-DDTC）, then adsorbed onto octadecyl silica membrane disk, recovered and determined by FAAS. Extraction efficiency, influence of sample volume and eluent flow rates, effects of pH, amount of Na-DDTC, nature and amount of eluent for elution of metal ions from membrane disk, break through volume and limit of detection have been evaluated. The effect of foreign ions on the percent recovery of heavy metal ions has also been studied. The limit of detection of the proposed method for Ni^2＋, Cd^2＋, Pb^2＋, Zn^2＋, Cu^2＋ and Co^2＋was found to be 2.03, 0.47, 3.13, 0.44, 1.24 and 2.05 ng·mL^-1, respectively. The proposed （DDTC） method has been successfully applied to the recovery and determination of heavy metal ions in different water samples.     

A chelating resin with bis[2-(2-benzothiazolylthioethyl)sulfoxide]: Synthesis, characterization and properties for the removal of trace heavy metal ion in water samples

A new chelating resin containing bis[2-(2-benzothiazolylthioethyl)sulfoxide] was synthesized using chloromethylated polystyrene as material and characterized by elemental analysis and infrared spectra. The adsorption capacities of the newly formed resin for Hg²⁺, Ag⁺, Cu²⁺, Zn²⁺, Pb²⁺, Mn²⁺, Ni²⁺, Cd²⁺ and Fe³⁺ were investigated over the pH range 1.0-6.0. The resin exhibited no affinity for alkali or alkaline earth metal ions. The maximum adsorption capacities of the resin for Hg²⁺, Ag⁺, Cu²⁺, Zn²⁺, Pb²⁺, Mn²⁺, Ni²⁺, Cd²⁺ and Fe³⁺ were 1.49, 0.96, 0.58, 0.11, 0.37, 0, 0.24, 0.36 and 0.25 mmol g⁻¹, respectively. In column operation it had been observed that Hg²⁺ and Ag⁺ in trace quantity could be separated from different binary mixtures and Hg²⁺ could be effectively removed from industrial wastewater and the natural water spiked with Hg²⁺ at usual pH.     

Effect of pH on Competitive Adsorption of Cu(II), Ni(II), and Zn(II) from Water onto Chitosan Beads

The amounts of adsorption of Cu²⁺, Ni²⁺, and Zn²⁺ from single, binary, and tertiary nitrate solutions onto glutaraldehyde cross-linked chitosan beads were measured. The beads had an average particle size and pore volume of 2 mm and 0.06 cm³/g, respectively, and had a BET surface area of 60 m²/g. All experiments were performed at 298 K as a function of initial pH (2.0–5.0), total metal concentration (0.77–17.0 mol/m³), and molar concentration ratio (0.25–4) in the aqueous phase. It was shown that the amount of metal adsorption generally increased with increasing solution pH. Competitive adsorption was significant in binary and tertiary systems when Cu²⁺ was present. The selectivity factor reached maximum in an equilibrium pH range of 5.1–5.3 and 4.5–4.9 for the Cu-Ni and Cu-Zn binary systems, respectively. This adsorbent provided a possibility for selective separation of Cu²⁺ from such multi-component solutions.     

Development of efficient method for preconcentration and determination of copper, nickel, zinc and iron ions in environmental samples by combination of cloud point extraction and flame atomic absorption spectrometry

A cloud point extraction procedure for the preconcentration of copper, nickel, iron and zinc ions in various samples has been described. Analyte ions in aqueous phase are complexed with 3-((indolin-3-yl)(phenyl)methyl)indoline (IYPMI) and following centrifugation quantitatively extracted to the aqueous phase rich in Triton X-114. The surfactant-rich phase was dissolved in 2.0 mol L⁻¹ HNO₃ in methanol prior to metal content determination by flame atomic absorption spectrometry (FAAS). The effects of some parameters including, the concentrations of IYPMI, Triton X-114 and HNO₃, bath temperature, centrifuge rate and time were investigated on the recoveries of analyte ions. At optimum conditions, the detection limits of (3 SDb m⁻¹) of 1.6, 2.8, 2.1 and 1.1 ng mL⁻¹ for Cu²⁺, Fe³⁺, Ni²⁺ and Zn²⁺ along with preconcentration factors of 30 and enrichment factor of 48, 39, 34 and 52 for Cu²⁺, Ni²⁺, Fe³⁺ and Zn²⁺ respectively, were obtained. The proposed cloud point extraction has been successfully applied for the determination of metal ions in real samples with complicated matrix such as biological, soil and blood samples with high efficiency.      

Study on the Liquid‐Solid Flotation Separation of Cadmium by Ammonium Sulfate‐Potassium Iodide‐Cetylpyridine Chloride‐Water System

The liquid‐solid flotation separation behaviors of Cd²⁺ in ammonium sulfate‐potassium iodide‐cetylpyridine chloride‐water system and the conditions for the separation of Cd²⁺ from other metal ions were studied. The results showed that in the presence of 1.0 g (NH₄)₂SO₄ and when the dosage of 0.1 M potassium iodide was 2.0 mL and 0.01 M cetylpyridine chloride (CPC) solution was 1.0 mL respectively, the formed water‐insoluble ternary association complex of KI‐CPC‐Cd floated above water phase and liquid‐solid phases were formed with clear interface. In this condition, Zn²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺ and Al³⁺ could not be floated and Cd²⁺ was floated quantitatively at pH 5.0. Therefore, the quantitative separation of Cd²⁺ from the above metal ions could be achieved. The quantitative flotation separation determination of Cd²⁺ in the sample of synthetic water and industrial waster water was performed, and the results agreed well with those by AAS method. The recoveries were 97.2%～102.4%, and the RSD was 1.8%.     

Synthesis of a Dithiocarbamate Chelate Resin and Its Oxidized form and Their Adsorption Properties for Heavy Metal Ions

A series of macroporous dithiocarbamate chelate resins, III and V, and an oxidized resin, VI, with high adsorption capacity were prepared. The influence of various reaction conditions of amination, dithiocarboxylation, and oxidation were examined. The structure and the conversion of functional groups of resins were confirmed by IR spectra and elemental analysis. The adsorption capacities of Resin II for Hg²⁺, Cu²⁺, Zn²⁺, and Cd²⁺ are 4.40, 2.44, 1.77, and 1.36 mmol/g, respectively. The adsorption capacities of Resins V and VI for Cu²⁺. Zn²⁺, Ni²⁺, Co³⁺, Ag⁺, Hg²⁺, Cd²⁺, Pb²⁺, and Au³⁺ are 4.07–0.51 and 3.81–0.59 meq ion/g, respectively. The adsorption rate and the influence of pH on the adsorption percentage of the resins for metal ions were examined. Noble metal, transitional metal, and heavy metal ions can be quantitatively adsorbed by the resins. The adsorbed Cu²⁺, Pb²⁺, Cd²⁺, Co³⁺, and Ni²⁺ can be quantitatively eluted with 5N HNO₃, and the presence of large amounts of Ca²⁺, Mg²⁺, Fe³⁺, and Al³⁺ did not interfere.     

Graphene quantum dots with Zn2+ and Ni2+ conjugates can cleave supercoiled DNA

Graphene quantum dots (GQDs), inheriting the superb property of graphene oxide, possess smaller lateral size and high biocompatibility, thus having potential in biomedical applications. We previously discovered that GQDs, combining with Cu²⁺ ions, could cleave DNA primarily through an oxidative pathway; yet, oxidative DNA cleavage is not practically preferred in biology. In this work, we explore the DNA cleavage ability of GQDs with Zn²⁺ and Ni²⁺. Zn²⁺ and Ni²⁺ alone are incapable of cleaving supercoiled DNA, but when combining with the GQDs, Zn²⁺ and Ni²⁺ exhibit DNA cleavage activity. However, the activity of these two systems is much lower than that of GQDs/Cu²⁺, and GQDs/Ni²⁺ is less active than GQDs/Zn²⁺. The functional mechanism of GQDs/Ni²⁺ and GQDs/Zn²⁺ is different from that of GQDs/Cu²⁺. The GQDs play a key role in the two systems; the redox inactive Zn²⁺ and Ni²⁺ ions assist to generate the oxidative species that eventually lead to the DNA cleavage. The current results together with our previous result indicate that GQDs together with metal ions can cleave supercoiled DNA, and their cleavage activities depend on the properties of metal ions: for redox active metal ions, metal ions play key roles, for redox inactive metal ions, GQDs are dominant.     

Synthesis of transition‐metal‐ion‐selective poly(N‐isopropylacrylamide) hydrogels by the incorporation of an Aza crown ether

A functionalized cyclam was synthesized by the attachment of a polymerizable acryloyl group to one of the four nitrogens on the cyclam molecule. The polymerization of the functionalized cyclam was performed with N‐isopropylacrylamide and N,N′‐methylene bisacrylamide, and the gels obtained were studied in the presence of different transition‐metal‐ion solutions. There was a drastic difference in the phase‐transition temperature (T_c) of the poly(N‐isopropylacrylamide) (PNIPAAm)/cyclam gel in comparison with the pure PNIPAAm gel. For the described system, a T_c shift of 15 °C was obtained. The presence of functionalized cyclam increased the hydrophilicity and T_c of the aforementioned polymer gels in deionized water (at pH 6) because of the presence of protonated amino moieties. The PNIPAAm/cyclam gels showed a dependence of the swelling behavior on pH. T_c of the pure PNIPAAm gel was weakly influenced by the presence of any transition‐metal ions, such as Cu²⁺, Ni²⁺, Zn²⁺, and Mn²⁺. The addition of Cu²⁺ or Ni²⁺ to the PNIPAAm/cyclam gel reduced T_c of the polymer gel, and a shift of approximately 12 °C was observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1594–1602, 2003     

A novel ion-imprinted nanocomposite for selective separation of Pb2+ ions

In this study, the ion-imprinting method has been integrated to develop a novel composite material for the selective separation of Pb²⁺ ions. Also, Pb²⁺ ion binding ability of the organosmectite based inorganic-organic composite incorporation of bicyclic C18 organic compound into smectite layers was conducted to draw a projection its potential use as a solid phase exchanger which is quite selective toward Pb²⁺ ions. The ion-imprinted nanocomposites were characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), swelling tests, and elemental analyses. After that, maximum binding capacity, pH, and equilibrium binding time were also been optimized. In order to show the selectivity of the composite synthesized, non-imprinted composites were also synthesized in absence of Pb²⁺ ions during polymerization. In this step, Ni²⁺, Co²⁺, Al³⁺, Zn²⁺, and Cu²⁺ ions were used as competitors under batch adsorption conditions. The relative selectivity coefficients of imprinted composite were calculated as 28.5, 156.5, 69.3, 24.8 and 131.6 for Pb²⁺/Co²⁺, Pb²⁺/Cu²⁺, Pb²⁺/Al³⁺, Pb²⁺/Zn²⁺, Pb²⁺/Ni²⁺ binary solutions, respectively. Finally, reusability of the composites was evaluated to show its cost-efficiency by repeating adsorption-desorption experiments ten-times. The adsorption capacity of the imprinted composites did not change significantly whereas that of non-imprinted version reduced dramatically.     

Study on Determination of Trace Nickel in Water Samples after Separation/enrichment using Microcrystalline Phenolphthalein Loaded with Chelate

The paper presents a novel method for the separation/enrichment of trace Ni²⁺ using microcrystalline phenolphthalein loaded with chelate prior to the determination by spectrophotometry. The effects of different parameters, such as the dosages of phenolphthalein and sodium diethyldithiocarbamate (DDTC), various salts and acidity on the enrichment yield of Ni²⁺ have been investigated to select the experimental conditions. The possible enrichment mechanism of Ni²⁺ was discussed. The results showed that under the optimum conditions, Ni²⁺ could be quantificationally adsorbed on the surface of microcrystalline phenolphthalein in the form of the chelate precipitate of Ni(DDTC)₂, while K⁺, Na⁺, Ca²⁺, Mg²⁺, Zn²⁺, Fe²⁺, Al²⁺, Pb²⁺ and Cd²⁺ could not be adsorbed at all. Therefore, Ni²⁺ was completely separated from the above metal ions in the solution. A new method for the separation/enrichment and determination of trace nickel using microcrystalline phenolphthalein loaded with chelate was established. The proposed method has been successfully applied to the determination of Ni²⁺ in various water samples, and the results agreed well with those obtained by FAAS method.     

Fourier transform far-infrared studies on transition metal ion-exchanged zeolites A

FT-FIR spectra of xeolites A containing Mn²⁺, Co²⁺, Ni²⁺, Cu⁺ and Zn²⁺ ions were recorded after heat treatment at 573 K in vacuo. The bands were assigned to the vibrations of the cations with respect to the zeolite framework. From obeying the Butler expression it can be inferred that transition metal ions preferably occupy SI sites in zeolite A. Upon adsorption of rare gas and diatomics the bands of the cation vibration diminish and are unspecifically shifted up- and downscale.     

Mass transfer determining parameter in facilitated transport through di-(2-ethylhexyl) dithiophosphoric acid activated composite membranes

Activated composite membranes (ACMs) containing di-(2-ethylhexyl) dithiophosphoric acid (D2EHDTPA) as a carrier have been found to facilitate the transport and separation of several cations. This paper describes an approach to the chemical characterisation of the transport phenomena of Zn²⁺, Cd²⁺, Cu²⁺, Ni²⁺, Sn²⁺ and In³⁺ by an ACM. The selectivity of D2EHDTPA based ACM towards different metal ions is presented and discussed focusing in Zn²⁺ and Cd²⁺ transport and recovery. Selectivity demonstrates that zinc ions are removable from mixtures due to the different extraction strength of D2EHDTPA. Such selectivity is based on the differences of the dynamic behaviour of the metal ions transport. In addition, a correlation of the chemical behaviour of those ACM systems with the corresponding solvent extraction systems has been found.     

Synthesis and characterization of 2-(5-Bromo-2-Pyridylazo)-5-[(N,N-dicarboxylmethyl) amino]- phenol as a water-soluble chromogenic reagent

A new water soluble chromogenic reagent, 2-(5-bromo-pyridylazo)-5-[(N,N-dicarboxylmethyl)amino]-phenol has been synthesized. Its colour reaction with various metal ions was tested, and the acid dissociation constant of the reagent, and the stability constants of the chelates of Ni²⁺, Co²⁺, Cu²⁺, Mn²⁺, Pb²⁺, Zn²⁺ and UO ₂ ²⁺ were determined. The application of the reagent to spectrophotometric determination of nickel in irons is presented.     

Silver nanoparticle loaded on activated carbon and activated carbon modified with 2-(4-isopropylbenzylideneamino)thiophenol (IPBATP) as new sorbents for trace metal ions enrichment

The efficiencies and performances of silver nanoparticle loaded activated carbon modified with 2-(4-isopropylbenzylideneamino)thiophenol (IPBATP-Ag-NP-AC) and activated carbon modified with IPBATP (IPBATP-AC), as new sorbents, were evaluated for separation and preconcentration of Cu²⁺, Zn²⁺, Co²⁺, Cd²⁺ and Pb²⁺ ions from real environmental samples. The retained metals content was reversibly eluted using 5?mL of CH₃COOH (6.0?mol?L^?1) and/or 10?mL of 4.0?mol?L^?1 HNO₃ for IPBATP-Ag-NP-AC and IPBATP-AC, respectively. The experimental parameters influence the recoveries of metal ions including pH, amounts of ligand and supports, condition of eluents, sample and eluent flow rates of has been investigated. The preconcentration factors were found to be 100 for Zn²⁺, Cd²⁺, Co²⁺, Cu²⁺ and 50 for Pb²⁺ ions using IPBATP-Ag-NP-AC, and 50 for Zn²⁺, Cd²⁺, Co²⁺, Cu²⁺ and 25 for Pb²⁺ ions using IPBATP-AC. The detection limit of both SPE-based sorbents was between 1.6–2.5?ng?mL^?1 for IPBATP-AC and 1.3–2.5?ng?mL^?1 for IPBATP-Ag-NP-AC. The proposed methods have been successfully applied for the extraction and determination of the understudy metal ions content in some real samples with extraction efficiencies higher than 90% and relative standard deviations (RSD) lower than 2.4%.     

Application of ion-imprinted polymer synthesized by precipitation polymerization as an efficient and selective sorbent for separation and pre-concentration of chromium ions from some real samples

In this study, a new Cr(III)-imprinted polymer (Cr(III)-IIP) is prepared from CrCl₃·6H₂O, methacrylic acid functional monomer, ethyleneglycoldimethacrylate cross-linking agent, 2,2?-azobisisobutyronitrile radical initiator and 2,2-(azanediylbis (ethane-2,1-diyl))bis(isoindoline-1,3-dione) ligand. To obtain the maximum adsorption capacity, the optimum condition was studied through pH, type and concentration of eluent, IIP weight, sample volume as well as the adsorption and desorption times. The Cr(III) ion content was determined via flame atomic absorption spectrometer. In optimum conditions, the adsorption capacity of the IIP for Cr(III) was obtained to be 74.65 mg g^?1, using 50 mg of IIP and the initial pH solution of 3.0. Both the adsorption and desorption times for quantitative analyses of Cr(III) ions were 15 and 5 min; respectively. After elution of the adsorbed ions by 3 mL of 4 mol L^?1 HNO₃ aqueous solution, the established IIP-based SPE procedure provides a reasonable pre-concentration factor of 100. The IIP-based pre-concentration method provides a low detection limit of 1.7 µg L^?1 with good repeatability (RSD?=?3.22%). Reusability studies confirmed that synthesis IIP is reusable and recoverable up to six cycles. According to the selectivity experiments, it was concluded that the prepared sorbent possesses more affinity toward Cr(III) ions than other ions such as Al³⁺, Pb²⁺, Cu²⁺, Mn²⁺, Fe²⁺, Zn²⁺, and Ni²⁺ ions. To evaluate the potential applicability of the proposed separation method, the pre-concentration and determination of trace amounts of Cr(III) were performed successfully in food samples with complex matrices, a bestial sample (i.e. cow liver) and an herbal product (i.e., broccoli) as real samples.     

Construction of template ligand sites in polymeric matrices with dithizone

Metal ion specific template ligand sites were developed by physically immobilizing dithizone molecules oriented according to a particular complex geometry in various polymeric films. Four polymeric systems, polystyrene, poly(methyl methacrylate), poly(vinyl chloride), and polycarbonate, were used for making template sites for Cu²⁺, Ni²⁺, Zn²⁺, and Co²⁺ ions. A high degree of specificity could be achieved independent of stability constants, though about half of the ligand sites were unavailable to the metal ions. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3729–3734, 1997     

Novel nanostructured dendrimer based on 1,3-bis(4,6-dichloro-1,3,5-triazine-2-yl)urea as an excellent adsorbent for Pb2+, Ni2+, Co2+ and Zn2+ metal ions

Human health is seriously harmed by the consumption of poor-quality water. Due to high toxicity and water solubility, heavy metals are present in wastewater discharged from numerous industries. In the environmental realm, metal-containing water must be treated before being released. A dendrimer is a superior adsorbent for the removal of heavy metal ions due to its nanostructure and hydrophilic end group. In this work, a novel triazine-based hydroxy-terminated dendrimer up to generation three is designed employing a carbamide core. The dendrimer's structure was explored using FT-IR and ¹H NMR studies. Full generation dendrimers UG1.0, UG2.0, and UG3.0 were utilized as an adsorbent for Pb²⁺, Ni²⁺, Co²⁺ and Zn²⁺ metal ion removal from water in a series of tests. The ability of dendrimers to uptake Pb²⁺, Ni²⁺, Co²⁺ and Zn²⁺ metal ions was investigated under various pH, time interval and dendrimer generation parameters. The presence of metal in the dendrimer was confirmed by FT-IR studies of dendrimer-metal complexes. The overall results show that Pb²⁺, Ni²⁺, Co²⁺ and Zn²⁺ metal ions uptake increases with the generation, time, and pH.     

Conductometric studies and application of new Schiff base ligand as carbon paste electrode modifier for mercury and cadmium determination

A new chemically modified carbon paste electrode by 2,2?-((pyridine-2,6-diylbis(azanylylidene))bis(methanylylidene))diphenol (L) ligand has been made and used as a sensor for determination of trace mercury and cadmium ions with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods. Complexation studies of the ligand with Cu²⁺, Zn²⁺, Hg²⁺, Ni²⁺ and Cd²⁺ ions by conductometric method in acetonitrile–ethanol mixture at 25°C show that the ML complexes have formed. The formation constants of complexes were calculated from the computer fitting of the molar conductance–mole ratio data, and the stability of the resulting complexes varied in order of Cd²⁺ > Hg²⁺ > Cu²⁺ > Zn²⁺ > Ni²⁺. Then a simple and effective chemically modified carbon paste electrode with L was prepared, and the electrochemical properties and applications of the modified electrode were investigated. Under the optimal conditions, the detection limit was 0.0494 μg L^?1 and 0.0782 μg L^?1 for cadmium and mercury ions, respectively, and the linear range for both metal ions were from 1 to 100 μg L^?1. The electrode shows high sensitivity, reproducibility and low cost, and was successfully applied to determination of Cd²⁺ and Hg²⁺ ions in water samples with recovery in the range of 97–101%.