Evaluation of magnesium sulphate attack in mortar-metakaolin system by thermal analysis

This paper reports an experimental study on the magnesium sulphate resistance of mortar specimens incorporating 0, 10 and 20% of metakaolin (MK). The evidence of the attack was evaluated through the content of calcium hydroxide (portlandite) and formation of magnesium hydroxide (brucite) by thermal analysis (thermogravimetric and derivative thermogravimetric analysis). The mechanical degradation of the mortar specimens was evaluated through splitting tensile tests after 200 days of exposition to the magnesium solution. The addition of metakaolin resulted in a reduction in the content of calcium hydroxide and in a smaller formation of brucite in comparison with reference mixture. A tensile strength loss of about 7% was observed for the metakaolin mortars submitted to the magnesium solution attack for 200 days.     

Differential thermal analysis of low-rank coals

Differential thermal analysis (DTA) of low-rank coals of high lignite to subbituminous rank from coal mines of Pakistan is reported. The studies carried out in dynamic oxygen atmosphere indicate that the exothermic reactions occur between 300 and 650°C and that the samples undergo stepwise oxidation of the organic matter rather than a continuous process as indicated by the pattern of shoulders from 250 to 350°C accompanying the main peak around 450°C. The effect of heating rate, particle size and volatile content was also studied in relation to oxidation. The results show that the increase in heating rate from 10 to 80 deg min⁻¹ results in a marked shift in all the events in the DTA curve towards higher temperatures. As for the effect of particle size, the DTA records of 100–75, 150–100, 250–150 μm and greater than 250 μm fractions show that the magnitude and position of shoulder peaks are more sensitive to changes in particle sizes compared to the main peak. The curves recorded to study the effect of changing volatile content of samples between 30–40% indicate a complex pattern of shoulders accompanying the main peak. In general, the number of shoulder peaks increases with increasing volatile content of samples but their positions do not follow any trend. The DTA curves recorded in nitrogen contain ill-de-fined oxothermic effects over the 300–750°C temperature range. These curves consist of an endothermic peak around 150°C, two exothermic shoulders in the temperature region 300–400°C and a large broad exothermic whip between 500 and 700°C. The heating rates have similar effects as in oxygen while the particle size do not influence the results. It has been concluded that the organic matter in the coals studied here is extremely heterogeneous with different burning characteristics; as a result it is very difficult to quantify energy changes associated with poorly resolved exothermic events along the DTA curve. The effects also dominate in N₂ atmosphere thus making identification of mineral matter difficult. The overall pattern of DTA events in oxygen can be correlated with the heating rate, particle size and volatile content of samples.     

Characterization of fatty acid methyl esters by thermal analysis

The thermal stability of selected straight-chain (C₆-C₁₄) esters of fatty acids has been studied by TG-DTG and DTA analysis. In DTG, a peak is detected between 84° and 125° C followed by a main effect in the range 105°–215°C, whereas in DTA only an exothermic peak appears in the range of 126.5° to 187°C (onset temperatures). The temperatures of these effects have been related with ignition points, molecular weights and boiling points. The characteristics of melting and recrystallization of the above fatty acid methyl esters and those with carbon numbers between C₁₄ and C₂₄ have been established by DSC along the melting range between ?83° and 50°C. Polymorphism appears in caproic, heptanoic, palmitic and stearic acid methyl esters.     

废轮胎热解特性研究

利用TG/DTG对不同来源的三种废轮胎样品的热解特性进行了研究,并得到了热解动力学参数。结果表明,新旧废外轮胎样品热解趋势基本一致,均经历了一个不明显的失重过程和两个明显的失重过程,其原因是由于废外轮胎中的橡胶组分比较复杂;内轮胎样品中的组分比较单一,其热解过程比较简单,仅经历了一个不明显的失重过程和一个明显的失重过程;三种样品的主要失重温度为600K～800K,转化率为0.2～0.8;使用一级动力学反应模型很好的拟和了三种样品的主要失重过程,并求出了热解动力学参数。     

A study of sulphonated and oxidized coals by thermal analysis

Earthy and xylytic brown coals from Poland have been sulphonated with 98% sulfuric acid at temperatures of 60°, 90° and 140°C. The main exothemic peak shifts to higher temperatures with increase in sulphonation reaction temperature whereas overall weight loss to 1000°C decreases. DTA curves of earthy and xylytic coals sulphonated at higher temperatures are similar, even though DTA curves of the unmodified coals differ appreciably. Thermal decomposition of earthy coal oxidized by nitric acid follows a different pattern. Nitric acid causes oxidation and depolymerization of the organic components and this is reflected in the shapes of DTA and TG curves of oxidized coals. As the nitric acid concentration and reaction temperature increase, the main exothermic peak shifts to lower temperatures (from 330°C for basic coal to 270°C for coal oxidized with 30 and 50% nitric acid). The weight loss is higher for oxidized coal than for coal unmodified by nitric acid.     

型煤燃烧固硫特性的TG/DTG-GC研究Ⅱ不同固硫剂/助燃剂对型煤燃烧性能的影响

采用TGDTG-GC技术研究不同固硫剂助燃剂对型煤燃烧性能的影响。结果表明,助燃剂在对煤燃烧产生助燃作用的同时减少甚至消除燃烧反应后期SO2的释放,进一步证实固硫剂与助燃剂的协同作用。同时,有些固硫剂本身也是一种助燃剂,单一组分助燃剂的助燃作用远不如复合型助燃剂,但二者助燃作用均与固硫剂有关。     

Waste mixture composition by thermogravimetric analysis

In this work thermogravimetric analysis is applied to examine pyrolysis of single waste components and their blends in order to determine the composition of an unknown waste mixture. The superposition property is assumed, i.e. the mixture thermal degradation curve is obtained as the sum of the curves corresponding to its constituents. The results show that if blended, the individual components are more clearly recognised from the differential mass loss curves. This allows a better identification of the composition. Inaccuracy in determining the composition increases if interactions occur between components, which is the case for PVC-newspaper blend. This revised version was published online in July 2006 with corrections to the Cover Date.     

Evaluation of thermal behavior of latex membranes from genetically improved rubber tree (Hevea brasiliensis)

Thermal stability, thermal decomposition process, residual mass, temperature of glass transition (T_g) and temperature dependence of storage modulus (E’), were determined for latex membranes prepared from six clones of Hevea brasiliensis: IAC 331, IAC 332, IAC 333 and IAC 334 grown at experimental plantations of Instituto Agronômico de Campinas (IAC) in Votuporanga, São Paulo State, Brazil. Latex membranes from GT1 and RRIM 600 Asian matrix clones were used as references. The thermal behavior of latex membranes from genetically improved rubber trees was characterized using thermogravimetry/derivative thermogravimetry (TG/DTG), differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The thermal behavior of latex from clones studied in the present work showed similar features of the clones previously reported (IAC 40, IAC 300, IAC 301, IAC 328, IAC 329 and IAC 330), with mass loss in four consecutive steps, except IAC 333, which showed an additional mass loss step.     

Thermal analysis study of the effect of coal-burning additives on the combustion of coals

Thermal analysis is widely used in combustion research for both fundamental and practical investigations. Efficient combustion of coals in cement industry is very important and necessary. In this research, the effects of three coal-burning additives on burning behaviour of bituminous coal and anthracite were studied with the help of thermogravimetry (TG) and differential scanning calorimetric (DSC) analysis. The kinetic study was carried out and the results were presented. The results showed that the coal-burning additives especially LSZ can reduce the ignition temperature, increase the ignition index D _i, combustion ending index D _f and affect the activation energy of the coal samples studied. The coal-burning additives especially LSZ can improve coal combustion effectiveness.     

Evaluation of pozzolanic activity of natural and artificial pozzolans by thermal analysis

In this research, the pozzolanic activity of natural and artificial pozzolan used for preparation of restoration mortars was evaluated. For this purpose, several pastes were prepared, by mixing two artificial pozzolans and a natural one with commercial hydrated lime, in different ratios. The pastes were cured in standard conditions (RH = 98%, T = 25 °C). The pozzolanic activity was evaluated by using simultaneous differential thermal and thermogravimetric analysis (DTA/TG) after curing for 3, 7, 14, 28 days. The obtained results revealed that the various lime/pozzolan pastes displayed different reaction kinetics and therefore the various pozzolans present different reactivity, in proportion to its mineralogical, physical and chemical characteristics.     

Sulfonation of arylamines: Part 12. Kinetics of thermal decomposition of dimethylanilinium sulfates

Three dimethylanilinium sulfates (DMAS) have been prepared and characterised by elemental and spectral studies. Thermal decomposition of these salts has been studied by TG and simultaneous TG-DTG technique and kinetic parameters were evaluated from both dynamic and isothermal TG data using mechanism based kinetic equations. The thermal decomposition pathways have also been suggested and it has been found that DMAS salts give dimethyl aminobenzenesulfonic acids (DMABSA) via solid state reaction. The primary step in the thermal decomposition involves proton transfer followed by sulfonation.This revised version was published online in November 2005 with corrections to the Cover Date.     

Thermal behaviour of intercalated 8-hydroxyquinoline (oxine) in montmorillonite clay

The composite montmorillonite-8-hydroxyquinoline (Swy-1-8-HQ) was prepared by two different processes and studied by using thermogravimetric analysis (TG/DTG and DSC), as well as helpful techniques as fluorescence in the UV-visible region and X-ray diffraction. The composites developed fluorescent appearance, however with quantum poor efficiency and they exhibited distinct TG and DSC thermal behavior. The fluorescence data of spectra associated to the TG/DT curves allowed to suggest that the 8-HQ was present in the composites in two different circumstances: 1 - intercalated in the interlayer spaces (Swy-1-8-HQ2), rigidly associated to the substrate feasible as a monolayer with the aromatic rings parallel to the silica layer; and/or, 2 - adsorbed on the surface (Swy-1-8-HQ1), either as a bilayer formation or tilting of the molecules to the silicate layer sheet. All results confirmed above are in agreement with X-ray diffraction patterns, once the interlayer space increases when 8-HQ is incorporated. The experimental results confirm the formation of the composites in agreement with the method used in the preparation. This revised version was published online in August 2006 with corrections to the Cover Date.     

ZnAc2·2H2O在空气中的热分解动力学研究

用TG/DTA,DSC和XRD技术研究了固态物质ZnAc2.2H2O在空气中的热分解过程.结果表明,ZnAc2.2H2O在空气中发生两步分解,其失重率与理论计算失重率相符.XRD结果表明,ZnAc2.2H2O分解的最终产物为ZnO.用Friedman法和Flynn-Wall-Ozawa(FWO)法求得分解过程的活化能E,并通过多元线性回归方法给出了可能的机理函数.ZnAc2.2H2O在空气中两步分解的活化能分别为119.82和66.82kJ/mol.     

环戊烷和环己烷在silicalite-1分子筛上的热脱附行为

采用智能质量分析仪(IGA)及TG/DTG法研究了环戊烷和环己烷在硅沸石silicalite-1上的热脱附行为。当环戊烷在silicalite-1上吸附量小于4 m/uc时,TG/DTG曲线表明环戊烷在silicalite-1上存在一个脱附过程。吸附量大于4 m/uc,TG曲线显示热脱附过程明显分为两个阶段,DTG曲线中出现两个明显的脱附峰,彼此分离。环己烷在silicalite-1上只存在一种脱附过程,DTG曲线只出现一个脱附峰。从环戊烷和环己烷的热脱附曲线中也可看出,随着吸附量的增加脱附峰温逐渐向高温方向偏移。     

Thermal Decomposition of Hydrated Lanthanide Picrates by TG/DTG and DSC Analyses

Hydrated lanthanide picrates with a composition of: Ln(pic)₃⋅xH₂O (Ln=La–Lu, Y) were synthesized and characterized. Thermal decomposition of the picrates by TG/DTG and DSC techniques are reported. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of chemical demineralization on thermal behavior of bituminous coals

Growing environmental concerns and the need for alternatives for oil and natural gas resulted in intensive researches on ultra clean coal (UCC). Therefore, the researches related to practice and application of various methods to produce UCC become more important. Thermal characterization of chemically demineralized coals by thermogravimetric analysis method is presented in this study. The aim of the study is to provide thermal data for HF–HNO₃ leaching system used for the production of UCC. Coal samples were first physically enriched by density separation. Then the enriched portion was chemically demineralized by using HF and HNO3, respectively. Ash content of coal samples were reduced to a range of 0.12–0.41% by chemical demineralization process. The petrographic, ultimate and proximate analyses were carried out to determine main features of samples. Physically and chemically enriched coal samples were then analyzed in a TG by two different techniques separately. The first technique covered thermal characterization of samples under non-isothermal conditions. Characteristic temperatures for each sample were obtained from the TG and DTG data. The second technique involved the determination of reactivity of in situ produced chars of each sample.     

A Study of the Hydration of Lime-Pozzolan Binders

DTA/TG and TG/DTG thermal studies and XRD investigations were carried out on pastes of lime-pozzolan binders to examine the relative hydration process. The binders were prepared with two natural pozzolans and hydrated lime, mixed together in different proportions. The main hydrated phases formed in the pastes are calcium silicate hydrate (CSH) and mono-carboaluminate. The growth of CSH was greater for the paste of the pozzolan richer in reactive constituents. For pastes with a higher lime/pozzolan ratio, a slowing of the formation of CSH was observed, while the formation of monocarboaluminate was more intense. The calcium hydroxide contents of the pastes obtained by thermogravimetric analysis made it possible to determine the pozzolanic activities of the two pozzolans under examination. The mortars for the various lime-pozzolan binders displayed characteristic hardening. This revised version was published online in July 2006 with corrections to the Cover Date.     

A thermal analysis study of the combustion characteristics of Victorian brown coals

Simultaneous TG, DTA techniques have been applied to investigate the combustion characteristics of Victorian brown coal derived from different coal fields and including various lithotypes. TG and DTA profiles of the entire combustion process were obtained to provide a set of parameters which characterize the oxidation potential of these coal samples. These parameters can also be used to predict the combustion performance of pulverized coal in industrial furnaces. The area of the major DTA combustion peak is closely related to the heat released during the combustion process and therefore provides a means of determining the specific energy of the coal. Different lithotypes are also characterized by their corresponding TG and DTA burning profiles.     

Feasibility Study of Crude Oil Fields by Thermal Analysis Techniques

This paper investigates the minimum oil content necessary for self-sustained combustion, which is introduced as a criterion for the selection of suitable reservoirs for in-situ combustion processes. Differential scanning calorimetry was used to determine the heat values of oil-limestone mixtures. The minimum temperature required for the total consumption of the fuel was obtained by thermogravimetry (TG/DTG). The minimum amount of oil necessary to sustain combustion was calculated from these two parameters and compared with the oil content of the reservoir. Reservoirs with an oil content greater than or equal to this minimum value were considered feasible. It was seen that the fields examined are generally not suitable for in-situ combustion processes. This revised version was published online in August 2006 with corrections to the Cover Date.     

Studying the ash behaviour of agricultural residues using thermal analysis

In this paper, the ash behaviour of some typical Mediterranean agricultural residues, such as peach stones, cotton gin wastes and grape residues is studied via simultaneous, (DTA/TG), thermal analysis methods. Furthermore, the effect of various pre-treatment techniques, such as fractionation and leaching, on the ash behaviour of the specific residues is also studied. Fractionation improves some of the main biomass properties such as calorific value, volatiles and ash content but deteriorates significantly the ash chemical composition of the remaining ash fraction. Leaching improves both the main properties of the treated biomass samples and the chemical composition of the remaining ash fraction, while the combination of the two pre-treatment methods results in a merge of their main advantages leading to an even larger improvement of the ash thermal behaviour. This revised version was published online in July 2006 with corrections to the Cover Date.