聚L-乳酸/聚(天冬氨酸-co-乳酸)共混物的制备及其相容性研究

采用氯仿/乙醇共沸溶液浇铸法制备了混合均匀的聚L-乳酸/聚(天冬氨酸-co-乳酸)共混物(PLLA/PAL)体系.研究了PLLA/PAL共混体系的热性能、结晶行为、形态结构和力学性能,评价了PLLA和PAL之间的相容性.结果表明,PAL对PLLA的结晶行为和热性能产生了较大的影响,共混物的结晶度较低,共混体系中部分PAL会进入PLLA球晶的片晶而导致PLLA球晶结构不完善,熔点降低.PAL的含量小于20%的PLLA/PAL共混物的拉伸强度和断裂延伸率均高于纯PLLA.PLLA和PAL分子链相互缠结,产生的氢键使分子链间存在较强的相互作用,具有较好的相容性.     

聚环氧乙烷(PE0)与聚双酚A羟基醚(PBHE)共混体系的研究

用偏光显微镜(PLM)、扭辫(TBA)、IR及WAXD对PEO/PBHE共混体系结晶形态进行了研究。结果表明,PEO含量在50％以上的共混体系,几乎完全被PEO球晶充满,非晶态PBHE作为微区分散在大球晶之间或球晶之中。PEO含量为40％和30％的照片上呈现树枝晶。PEO含量为20％以下时照片中不再看到结晶出现,PEO与PBHE形成单一非晶相。PEO/PBHE共混体系的组分之间存在着氢键相互作用,这种作用强于PBHE分子间的氢键作用。共混体系的结晶度及T_g随PBHE组分含量的增加,前者减小后者增加并符合FOX方程揭示的规律。PEO与PBHE具有很好的相容性。     

聚环氧乙烷(PE0)与聚双酚A羟基醚(PBHE)共混体系的研究

 用偏光显微镜(PLM)、扭辫(TBA)、IR及WAXD对PEO/PBHE共混体系结晶形态进行了研究。结果表明,PEO含量在50％以上的共混体系,几乎完全被PEO球晶充满,非晶态PBHE作为微区分散在大球晶之间或球晶之中。PEO含量为40％和30％的照片上呈现树枝晶。PEO含量为20％以下时照片中不再看到结晶出现,PEO与PBHE形成单一非晶相。PEO/PBHE共混体系的组分之间存在着氢键相互作用,这种作用强于PBHE分子间的氢键作用。共混体系的结晶度及T_g随PBHE组分含量的增加,前者减小后者增加并符合FOX方程揭示的规律。PEO与PBHE具有很好的相容性。     

苯乙烯-马来酸酐共聚物增容Nylon-6/ABS共混体系的形态和力学性能

通过熔融共混法制备了苯乙烯-马来酸酐共聚物(SMA)增容的尼龙6(Nylon-6)/ABS共混物.采用TEM、SEM、FTIR等研究了SMA增容的Nylon-6/ABS共混物的相形态与性能.发现在Nylon-6和ABS的简单共混体系中,分散相易聚集,相界面清晰,断裂面光滑,呈脆性断裂,相容性差.加入少量SMA后,共混物由共连续相结构转变为典型的"海-岛"结构,分散相分布均匀,界面粘接程度增加,表明SMA对Nylon-6/ABS体系有显著的增容效果.     

改性酚氧树脂/聚(甲基丙烯酸丁酯-co-4-乙烯基吡啶)共混物的相容-络合行为和表面表征

合成了一系列不同4-乙烯基吡啶含量的聚(甲基丙烯酸丁酯-co-4-乙烯基吡啶)(BVPy)共聚物,并对酚氧树脂(Phenoxy)的仲羟基进行了不同乙酰化程度的改性.用粘度法和激光光散射(LLS)研究了BVPy/改性Phenoxy共混物在溶液中的络合行为对氢键相互作用基团密度的依赖性,并用DSC研究了共混体系在本体中的相容性.将粘度法及LLS的结果结合起来,得到了改性Phenoxy/BVPy共混体系的不相容-相容-络合转变相图.在此基础上,用XPS初步考察了共混物的相容性对其表面组成的影响.结果表明,大分子间的络合相互作用可抑制共混物的表面富集.     

聚甲醛和尼龙12共混物的微观结构与力学性能

采用SEM、FT-IR、DSC、WAXD等方法对POM/PA12共混物的微观结构进行分析,并测试其力学性能,结果表明,在POM/PA12共混物中,存在着氢键的相互作用.PA12的加入,使POM的熔点下降,共混物的微晶尺寸入L₁₁₀及晶胞参数有所增大.微晶尺寸L₁₁₀在10.87¹4.89nm之间时,PA12对POM具有增韧改性作用.     

氯化镁/氯化1-丁基-3-甲基咪唑改性淀粉/聚丁二酸丁二醇酯共混材料的结构与性能

用氯化镁/氯化1-丁基-3-甲基咪唑([BMIM]Cl)复合增塑剂改性淀粉/聚丁二酸丁二醇酯(PBS)共混材料,采用红外光谱(FTIR)、扫描电子显微镜(SEM)、差示扫描量热分析(DSC)、X射线衍射分析(XRD)及力学性能测试等方法研究了氯化镁/[BMIM]Cl改性淀粉/PBS共混材料的结构和性能.结果表明,氯化镁能与淀粉及PBS形成较强的相互作用,从而破坏淀粉及PBS原有的氢键,导致淀粉/PBS共混体系结构和性能的改变.与[BMIM]Cl改性体系相比,氯化镁/[BMIM]Cl改性体系能进一步增强淀粉与PBS的界面结合力,提高共混体系的相容性;使淀粉/PBS的熔融焓、结晶度及结晶温度降低,冷结晶温度升高;提高共混体系的力学强度和断裂伸长率,抑制[BMIM]Cl因高效增塑产生的强度降低作用.采用氯化镁/[BMIM]Cl改性淀粉/PBS可制备出具有良好力学性能的淀粉/PBS共混材料.     

分子动力学模拟研究聚乳酸/聚酰胺11共混物的相容性

采用分子动力学(MD)模拟方法在COMPASS力场下,研究了不同质量比(10/90,30/70,50/50,70/30和90/10)聚乳酸(PLA)/聚酰胺11(PA11)共混物的相容性.研究结果表明:不同比例下PLA/PA11共混物的Gibbs自由能变化均大于零,其共混物很难形成均相体系;共混体系结合能的计算以及不同组分分子间C—C原子对径向分布函数的分析揭示了PLA和PA11的相互作用主要源自其分子间的范德华力;此外,模拟得到的所有比例下共混物的Flory-Huggins相互作用参数(χ)均大于临界Flory-Huggins相互作用参数(χcritical),进一步证明PLA与PA11不能形成相容体系。     

端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟和介观模拟

应用分子动力学(MD)和介观动力学(MesoDyn)模拟方法对固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性进行了研究. 采用MD模拟方法在COMPASS力场下, 对纯物质、HTPB/增塑剂共混物的密度、内聚能密度、溶度参数和共混物分子间的Flory-Huggins作用参数及结合能等进行了模拟计算, 通过比较溶度参数差值(Δδ)的大小、模拟前后体系密度变化情况均可以预测HTPB与增塑剂的相容性, 结合能的分析揭示了HTPB/增塑剂共混物组分间的相互作用及本质. 将Flory-Huggins作用参数转化为MesoDyn模拟的输入参数, 采用MesoDyn模拟方法对HTPB/增塑剂共混体系的介观形貌与动力学演变过程进行了研究, 通过模拟得到的等密度图、自由能密度和有序度参数等可以判断共混体系的相容性. MD和MesoDyn模拟结果均表明: HTPB/DOS属于相容体系, 而HTPB/NG属于不相容体系, 其结论与实验结果一致.     

端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟

固体推进剂和炸药的力学性能在很大程度上依赖于配方中高分子粘结剂与增塑剂的相容性. 本文对相容和非相容两种体系进行了分子动力学(MD)模拟, 以考察分子模拟方法的实用性. 为预测固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性, 采用MD模拟方法在COMPASS力场下, 对HTPB、DOS、NG和共混物HTPB/DOS、HTPB/NG的密度、内聚能密度及溶度参数等进行了模拟计算. 通过比较溶度参数差值(△δ)的大小、分子间径向分布函数和模拟前后体系密度变化情况均可以预测HTPB/DOS属于相容体系,而HTPB/NG属于不相容体系, 与实验结果一致. 径向分布函数分析同时揭示了HTPB/增塑剂组分之间的相互作用及本质. 本文的模拟方法可以作为预测聚合物与增塑剂相容性的有利工具, 也可以为固体推进剂和炸药的配方设计提供理论指导.     

Electrical and structural analysis of conductive polyaniline/polyacrylonitrile composites

Conducting composites of polyacrylonitrile (PAN) copolymer containing 10% mass ratio methylacrylate and dodecylbenzene sulfonic acid doped polyaniline (PANI-DBSA) were prepared by solution blending. Electrical properties of the blends were characterized by means of electrical conductivity measurements and the phase structures were investigated via scanning electron microscopy (SEM), X-ray diffraction (XRD), FT-IR spectroscopy, differential scanning calorimetry (DSC) and dynamical mechanical analysis (DMA). It was found that the electrical conductivity of the composites increased with the increase of PANI-DBSA content and the percolation threshold lay around 3.2 wt%. DSC and DMA measurements showed that there was only one T_g for each blend and the values of T_g varied with the PANI-DBSA content, implying that the PANI-DBSA/PAN blend was at least partially compatible. The formation of the hydrogen bonding between the carbonyl groups in PAN copolymer and the imine groups in PANI-DBSA was identified by the FT-IR spectra. XRD demonstrated that the intrinsic layered arrangement of PANI-DBSA was disaggregated in the blends. Nanosize network structure of PANI-DBSA dispersing in PAN matrix and the so-called phase reverse occurring in the skin layer of the film samples at low PANI-DBSA loading were observed by SEM.     

HIPS-g-GMA相容剂对PC/HIPS共混物相容性的影响*

将两种或两种以上聚合物进行共混是获得性能优异合金材料的简单而有效的途径[1,2 ] .但是大多数聚合物共混时 ,由于混合焓ΔＨ >0且混合熵ΔＳ非常小 ,导致混合自由能大于零 ,故大多数共混体系是不相容的 .而对于不相容的共混 ,由于两相间的界面张力大 ,两相间形成锐形界面 ,两相之间的界面粘结力低 ,导致材料性能很差 .为了改善两相间的相容性 ,需要加入相容剂[3 ,4 ] .绝大多数增容剂是嵌段或接枝共聚物 .这类增容剂分子量较大 ,在加工条件下 ,由于其粘度较大往往难于迁移到两相的界面处 ,起不到应有的增容作用 .聚合物反应加工技术是近 2…     

Morphology,mechanical, and fracture properties of HNBR modified ASA/SAN blends

In this work, acrylonitrile-styrene-acrylic terpolymer/styrene-acrylonitrile copolymer/hydrogenated nitrile rubber (ASA/SAN/HNBR) ternary blends with different composition were prepared by melt blending. Properties of the ternary blends were studied by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMTA), Fourier transform infrared spectra (FTIR), heat distortion temperature (HDT), melt flow rate (MFR), and Scanning electron microscopy (SEM). The results showed that the incorporation of HNBR can enhance the toughness by a large scale, and the two rubber phase showed partial miscibility. Heat resistance of the blends almost unchanged with HNBR content. FTIR told that the preparation of the ternary blends was a physical process, and no obvious phase separation was observed in SEM images.     

Preparation and electric property of PA/PVDF blend for energy storage material

This paper selected typical polar polymers which are polyvinylidene fluoride (PVDF) and polyamide (PA) to prepare PA/PVDF blend for energy storage material. Three kinds of PA (PA6, PA66 and PA11) with representative characters were chosen as the main research polymers for blending with PVDF. The electrical properties of three kinds of all-polymeric blends were tested and the microstructure was characterized by X-ray diffractometer (XRD), Fourier transform infrared instrument (FTIR), Scanning electron microscope (SEM) and Differential scanning calorimetry (DSC). Our finding suggests that the created high-ε polymeric blends represent a novel type of material that is easy to process. In addition, the dielectric constant and breakdown strength of PA/PVDFs are relatively high so that it can be applied to electronic components.     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Miscibility and surface properties of fluorinated copolymer blends involving hydrogen‐bonding interactions

The miscibility and underlying hydrogen‐bonding interactions of blends of a fluorinated copolymer containing pyridine and a nonfluorinated copolymer containing methacrylic acid were studied with differential scanning calorimetry (DSC), transmission Fourier transform infrared (TX‐FTIR) spectroscopy, and X‐ray photoelectron spectroscopy (XPS), whereas the surface properties of the blends were investigated with contact‐angle measurements, time‐of‐flight secondary‐ion mass spectroscopy, XPS, and attenuated total reflectance Fourier transform infrared spectroscopy. DSC studies showed that the presence of a sufficient amount of 4‐vinylpyridine units in the fluorinated copolymer produced miscible blends with the nonfluorinated copolymer containing methacrylic acid. TX‐FTIR and XPS showed the existence of pyridine–acid interpolymer hydrogen‐bonding interactions. Even though the anchoring effect of hydrogen bonding hindered the migration of the fluorinated component to the blend surface, it could not completely eliminate the surface enrichment of the fluorinated component and the surface rearrangement of the fluorinated pendant chain. The air–blend interface was mainly occupied by the fluorinated pendant chain, and the surface energies of the blends were extremely low, even with only 1.5 wt % of the fluorinated component in the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1145–1154, 2004     

多壁碳纳米管对环氧树脂/聚醚酰亚胺体系相分离的影响

通过溶液混合的方法制备了环氧树脂/聚醚酰亚胺(PEI)/多壁碳纳米管(MWCNTs)三元复合物,并使用扫描电镜(SEM)、原位红外分析(FTIR)、流变测试和非等温DSC等手段研究了MWCNTs的存在对体系相分离形貌和固化反应的影响.扫描电镜的结果显示,在固化后的样品中MWCNTs较均匀地分散在两相中.150℃下固化,不含MWCNTs和MWCNTs含量为0.75 pbw的体系相分离形貌呈海岛状结构,而进一步增大MWCNTs含量后相分离形貌呈双连续结构,且相区尺寸随MWCNTs含量的增加而减小.120℃下固化,不含MWCNTs和MWCNTs含量为0.75 pbw的体系相分离形貌呈双连续结构,而进一步增大MWCNTs含量后,体系相分离形貌呈相反转结构.FTIR和DSC的测试结果表明,MWCNTs表面的羟基对环氧树脂的固化反应起到催化作用,使得固化反应速度加快,反应活化能降低.而流变测试的结果表明,随着MWCNTs含量增加,一方面交叉跨越多个相区的碳纳米管使得体系黏度增大,对相分离起到了一定的抑制作用;另一方面使得体系凝胶化时间提前,导致体系相分离形貌被固定在相分离的较早阶段,起到有效调控相分离形貌的作用.     

Evidence of electron acceptor - electron donor interactions in thermoplastic polymer blends by using FTIR - ATR spectroscopy

Specific interactions in binary blends of ethylene/vinyl acetate copolymer (EVA) with various low molecular weight terpene-phenol tackifying resins (TPR) were systematically investigated, as a function of the composition of the blend and of the electron-acceptor ability of the resin, by using attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. Molecular acid-base were evidenced between TPR hydroxyl groups and EVA carbonyl groups. Quantitative information on the fraction of acid-base bonded entities, the enthalpy and the equilibrium constant of pair formation were obtained. A crystalline transition of the EVA copolymer is observed and is discussed in terms of enthalpy and entropy considerations based on FTIR and calorimetric differential scanning calorimetry (DSC) investigations. Fundamental results are then summarized in order to predict the interfacial reactivity of such polymer blends towards acid or basic substrates.     

用Z-N催化剂分段聚合制备PP/EPR共混物的结构和形态特征

用Ziegler-Natta(Z-N)催化剂MgCl2/TiCl4/BMF-AlEt3(BMF代表内给电子体9,9-二甲氧基甲基芴),采用分段聚合的方法制备了PP/EPR原位共混物,通过改变乙丙共聚的时间调节聚合物中乙烯的含量.使用核磁共振(13C-NMR)、凝胶渗透色谱(GPC)、示差扫描量热分析法(DSC)、动态力学分析(DMA)、扫描电子显微镜(SEM)和偏光显微镜(PLM)等研究了聚合物的结构和形态特征.研究发现,分段聚合制备的PP/EPR共混物是一种包括丙烯均聚物、乙丙无规和嵌段共聚物在内的多组分混合物.动态力学的结果显示混合物中聚丙烯与乙丙无规共聚物的玻璃化转变峰出现了内移现象,说明两者呈现部分相容性.扫描电镜的照片表明了聚丙烯基体与乙丙无规共聚物分散相之间的相界面模糊,两相之间的相容性较好.随着聚合物中乙烯含量的增加,分散相出现明显的塑性变形,同时,聚丙烯的结晶形态也发生明显的变化,球晶的尺寸逐渐变小,同时球晶变得不完善.     

聚乳酸/乙烯-醋酸乙烯酯共聚物共混物的形态与黏弹行为

熔融共混制备了不同组分比的聚乳酸(PLA)/乙烯-醋酸乙烯酯共聚物(EVA)共混物,采用扫描电子显微镜(SEM)、溶剂选择性蚀刻和旋转流变仪研究了共混物不相容的相形态及其黏弹响应.研究结果表明,PLA/EVA共混物为典型的热力学不相容体系,两基体组分间的界面张力约为2.2 mN/m;因此随组分比的不同,共混物表现出"海-岛"分散和双连续的不相容相形态;体系中EVA的相反转浓度约为50 wt%～60 wt%,这与黏性模型对相反点预测的结果一致;与双连续相形态的体系相比,乳液模型能够更好的描述具有"海-岛"分散形态的体系的线性黏弹响应,共混体系相对较宽的相反转区域主要源于两组分间较大的弹性比以及EVA自身的屈服行为.