含苯并咪唑单元可溶性聚酰亚胺的合成和性能

合成了一种刚性芳香二胺单体3,3',5,5'-四甲基-4,4'-二胺基苯基甲苯(BDAP),与6-氨基苯基-2-氨基苯并咪唑(BIA)组成混合二胺,分别与4种商品化的二酐单体(均苯四酸二酐(PMDA)、联苯四酸二酐(BPDA)、二苯酮四酸二酐(BTDA)和二苯醚四酸二酐(ODPA))一步法缩聚合成了一系列可溶性聚酰亚胺.采用FTIR,1H-NMR,UV-Vis,DMA和TGA等测试方法对所制备的聚酰亚胺进行了表征.结果表明,所制备的聚酰亚胺具有良好的溶解性能,能够在NMP和DMAc等常规溶剂中溶解;耐热性及力学性能优良,玻璃化转变温度超过410℃,分解温度在500℃以上.     

含磷聚酰亚胺纤维的制备及其力学与阻燃性能

采用廉价的三苯基氧膦和混酸合成了一种含磷二胺单体,二（3-氨基苯基）苯基膦氧(DAPPO)。在4,4′-二胺基二苯醚（ODA）、3,3′,4,4′-联苯四酸二酐（BPDA）和均苯四酸二酐（PMDA）聚合体系中引入该单体,制备含磷聚酰亚胺纤维。热失重分析（TGA）结果表明,聚酰亚胺纤维的热稳定性随含磷量的增加而明显提高。当n（DAPPO）：n（ODA）为7：93时,纤维的极限氧指数达到了43,说明纤维的阻燃性能显著提高。     

不同比例的s-BPDA/i-BPDA型聚酰亚胺共聚结构与性能关系

由不同比例的二酐单体3,3′,4,4′-联苯四酸二酐(s-BPDA)/2,2′,3,3′-联苯四酸二酐(i-BPDA)与二胺单体4,4′-二氨基二苯醚(4,4′-ODA)制得了一系列共聚可溶聚酰亚胺. 采用DSC 、TGA和拉伸等测试方法对所得共聚聚酰亚胺进行了表征, 实验结果表明, 所得聚酰亚胺具有优异的力学性能和热稳定性, 并且随着i-BPDA含量的增加, 聚酰亚胺的溶解性提高, 玻璃化转变温度(Tg)升高, 中间体聚酰胺酸的固有黏度降低.     

含哒嗪环聚酰亚胺的合成及性能表征

以马来酸酐为原料与水合肼反应得到哒嗪酮,再与三氯氧磷反应制备3,6-二氯哒嗪中间体,哒嗪中间体与间氨基苯酚通过亲核取代反应合成了一种新的二胺单体——3,6-二(3-氨基苯氧基)哒嗪.通过1HNMR,FTIR及HPLC-MS确证了哒嗪二胺及中间体的结构.这种哒嗪二胺单体与6种芳香二酐单体——均苯四甲酸二酐(PMDA)、3,3',4,4'-联苯四甲酸二酐(BPDA)、4,4-六氟异丙基邻苯二甲酸酐(6FDA)、3,3',4,4'-二苯甲酮四甲酸二酐(BTDA)、3,3',4,4'-二苯醚四甲酸二酐(ODPA)和双酚A型二醚二酐(BPADA)通过两步法聚合制备了一系列的聚酰亚胺,并对其结构和性能进行了研究.结果表明,聚酰胺酸的比浓对数黏度为0.37~0.50 dL/g,该系列聚酰亚胺膜具有良好的热稳定性和机械性能,玻璃化温度(Tg)为188~241℃,氮气氛围下5%和10%热失重分别为421~448℃和447~473℃,拉伸强度(TS)高达102 MPa,断裂伸长率(EB)为2.0%~6.5%.紫外可见光谱测试得到的截止波长(λcut-off)为367~389 nm.     

含磷聚酰亚胺纤维的制备与性能

合成了一种含磷二胺单体, 二(4-胺基苯氧基)苯基膦氧(DAPOPO). 该单体与4,4'-二胺基二苯醚(ODA)、 均苯四酸二酐(PMDA)和3,3',4,4'-联苯四酸二酐(BPDA)共聚得到聚酰胺酸溶液, 通过干喷湿纺法纺丝得到聚酰胺酸纤维, 聚酰胺酸纤维经过热亚胺化和热牵伸得到含磷的聚酰亚胺纤维. 利用纤维强度仪、 扫描电子显微镜、 热失重分析仪和氧指数测定仪等研究了含磷聚酰亚胺纤维的力学性能、 形貌、 热稳定性能和阻燃性能. 结果表明, 随着含磷量的增加, 纤维的热稳定性明显提高, 而极限氧指数从35上升到了45, 说明纤维的阻燃性能得到很大提高.     

侧链含邻苯二甲酰亚胺的聚酰亚胺液晶垂直取向剂的制备与表征

以邻苯二甲酰亚胺和溴代正辛烷为原料,合成了功能性二胺单体N-辛基-4(3,5-二氨基苯甲酰基)-氨基邻苯二甲酰亚胺(D8).用此单体与3,3’-二甲基-4,4’-二氨基二苯甲烷(DMMDA)、3,3’,4,4’-二苯醚四甲酸二酐(ODPA)共缩聚,采用低温缩聚-化学亚胺化方法,通过调节共聚物组成制备了5种聚酰亚胺(PI).利用FTIR、NMR、UV-Vis与DSC等手段对合成的二胺单体及聚酰亚胺进行了结构表征和性能测试;研究了其摩擦取向性能、透光性能、溶解性能和耐热性能.结果表明,5种聚酰亚胺均可溶于常见极性溶剂,如NMP、THF等;随着D8含量的增加,PI膜对液晶分子取向时的预倾角逐渐增大至垂直,当D8含量大于20%,且经过5次摩擦后,预倾角仍能保持在89°以上.此外实验所得PI透过率大于80%,玻璃化转变温度在260℃以上.     

三明治结构含铅聚酰亚胺材料的制备与辐射屏蔽性能研究

采用离子交换法合成了以化学方式键合铅离子的二胺单体4,4'-二氨基-1,1'-联二苯-2,2'-二磺酸铅BDSA(Pb),并与二胺单体4,4'-二氨基-二苯醚(ODA),二酐单体均苯四甲酸酐(PMDA)在溶剂N-甲基-2-吡咯烷酮(NMP)中完成缩聚反应,通过改变2种二胺单体的摩尔比,采用热亚胺法和流延法逐层浇筑的工艺,制备出了一系列侧基键合铅离子的三明治结构的聚酰亚胺复合材料PI(Pb),试图解决传统物理共混方法制备的复合材料中易出现的铅元素分布不均匀、机械性能差的科学问题.实验结果表明:以纯PI为参照物,制备的PI(Pb)复合材料对~(241)Am(59.5 keV)、~(238)Pu(79.9、176.7 keV)等中低能γ射线具有很好的屏蔽效果,而且具备优良的耐辐照性能、优异的热稳定性能和良好的力学性能.     

1,4-双[4-(2-氨基-5-苯基)噻唑基]苯及其聚酰亚胺的合成及性能

以１ ,４ 双（ 苯乙酰基） 苯为原料,合成了新有机二胺化合物———１ ,４ 双［４ （２ 氨基 ５ 苯基） 噻唑基］ 苯,以此二胺或４ ,４’ 二氨基二苯醚和３ ,３’,４ ,４’ 二苯酮四酸二酐反应制备出新型的聚酰亚胺均聚物和共聚物,研究了它们的耐温性能,耐热氧化性能和共聚物经高温裂解后的导电性能等     

二苯醚系高分子单体的新合成路线

二苯醚系高分子单体的新合成路线张志强，田正华（鞍山钢铁学院化工系，ｌｌ４００２）４，４’─二苯醚二甲酸，４，４’─二氨基二苯醚，３，３＇４，４’─二苯醚四甲酸二酐等取代二苯醚是一类重要的高分子单体，用于制备聚酰胺、聚酰亚胺和聚芳酯，在耐高温塑料、液晶...     

可溶性聚酰亚胺的制备及其在液晶显示器上的潜在应用

以3,5-二硝基苯甲酰氯和4-羟基联苯为原料,合成了功能性二胺单体3,5-二氨基苯甲酸联苯酯(DABBE).用此单体与3,3′-二甲基-4,4′-二氨基二苯甲烷(DMMDA)、3,3′,4,4′-二苯醚四甲酸二酐(ODPA)共缩聚,采用低温缩聚-化学亚胺化的方法,通过调节共聚物组成制备了5种聚酰亚胺(PI).利用FT-IR、NMR、UV-Vis与DSC等手段对合成二胺单体及聚酰亚胺进行了结构表征和性能测试;研究了其溶解性能、透光性能、取向性能和耐热性能.结果表明,5种聚酰亚胺均可溶于NMP、DMF等极性溶剂;对液晶分子取向时的预倾角随DABBE的比例增加而增大,可达1.8°.但当DABBE的比例增加时,PI的分子量降低,将影响其成膜性能.此外,实验所得的PI透过率大于80%,玻璃化转变温度在220℃以上.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.