非晶纳米高熵合金薄膜Nd-Fe-Co-Ni-Mn的电化学制备及磁学性能

通过电沉积方法在室温下制备了具有纳米结构组织的Nd-Fe-Co-Ni-Mn高熵合金磁性薄膜。 通过改变电沉积参数,如沉积电位、沉积时间,可控制薄膜的纳米结构及表面形貌。 扫描电子显微镜观察结果表明,在Ti基体上,-2.2 V下沉积5 min可制备出大小在200 nm左右的均匀分布的球形颗粒薄膜,延长沉积时间会使薄膜变得更加致密,而沉积电位的负移会导致纳米片的出现。 能谱结果表明5种元素发生了共沉积,结构分析表明该薄膜是无定形态的。 稀土元素Nd与过渡金属发生共沉积,可能是由于过渡金属离子与二甲基亚砜形成多核配位化合物而使得过渡金属离子沉积电位负移所致。 Nd-Fe-Co-Ni-Mn高熵合金薄膜在室温下具有良好的软磁性能。     

Co-Ni合金薄膜的电化学外延及同步辐射XMCD研究

采用电化学循环伏安法在单晶GaAs(001)衬底上外延沉积了Co-Ni二元合金薄膜. 扫描电子显微镜观察结果显示, 薄膜厚度约180 nm, 其表面由约40 nm大小的颗粒组成. 用X射线荧光法确定了薄膜的组分为Co66Ni34, XRD确定了其为面心立方结构. 用同步辐射圆偏振软X射线分别测量了样品中Co和Ni的吸收谱(XAS), 从而得到X射线磁性圆二色(XMCD)谱, 通过加和定则分别计算出了合金中Co和Ni的轨道磁矩和自旋磁矩, 与纯的Co和Ni样品相比, 它们都有不同程度的增加.     

二甲基亚砜中E-Ni-Co合金膜的电化学制备

利用循环伏安法和恒电位电解法研究了室温条件下在LiClO4-二甲基亚砜(DMSO)体系中Er-Ni-Co功能合金膜的电化学制备.实验结果表明, 在0.1 mol•L－1 ErCl3-0.1 mol•L－1 NiCl2-0.1 mol•L－1 CoCl2-0.1 mol•L－1 LiClO4-DMSO体系中,控制电位在－2.20～－2.50 V范围内进行恒电位电解,得到表面均匀、附着力强、有金属光泽的黑色非晶态Er-Ni-Co合金膜, 其中Er的质量分数可达9.21％～18.90％.     

在有机溶剂中Eu-Co-Ni合金薄膜的电化学制备

利用恒电位沉积、循环电位沉积和脉冲电沉积法在DMSO体系中在铜基体上探讨了Eu-Co-Ni合金薄膜的制备.实验结果表明,在0.10mol/LEuCl3-0.10mol/L CoCl2-0.10mol/L NiCl2-0.1 0mol/l LiClO4-DMSO体系中,恒电位沉积技术制备出的Eu-Co-Ni合金膜表面较为粗糙,其中Eu含量为5.46～6.01 wt%,脉冲电沉积技术制备的Eu-Co-Ni合金膜表面平整,致密,附着力好,且有金属光泽,其中Eu含量为6.76%,循环电位扫描技术制备的Eu-Co-Ni合金膜表面平整,致密,附着力好,其中Eu含量为12.43%.通过XRD证明所得的合金薄膜为非晶态.     

乙酰胺-尿素-NaBr熔体中Gd-Ni合金的电化学制备

熔盐电解法制取稀土合金功能材料具有低成本等优点.本文选取353 K的乙酰胺-尿素-NaB r熔体,应用循环伏安法研究镍于该熔体(含0.063 mol.L-3N iC l2)、Pt、Cu电极上的还原.实验表明,N i(Ⅱ)+2 eN i(0)是一步完全不可逆反应,测得在Pt上N i(Ⅱ)的传递系数α=0.28,扩散系数D0=4.63×10-5cm2.s-1,Cu上α=0.22,D0=6.05×10-7cm2.s-1.以Cu作基体,Gd(Ⅲ)于该熔体不能单独还原为Gd(0),但可以被N i(Ⅱ)诱导共沉积.由恒电位法电解得到的Gd-N i合金,Gd(0)的含量随电解电位、Gd(Ⅲ)/N i(Ⅱ)摩尔比及电解时间的变化而变化.控制电解电位为-0.75 V,Gd(Ⅲ)/N i(Ⅱ)摩尔比为1∶1,电解20 m in.所得合金膜是非晶态的.     

二甲基甲酰胺中Y-Mg-Co合金膜的电化学制备

研究了二甲基甲酰胺（DMF）中Y(Ⅲ) 和Mg(Ⅱ) 及Co(Ⅱ)在Pt电极上的电化学行为.结果表明,Y(Ⅲ)、Mg(Ⅱ)及Co(Ⅱ)在Pt电极上一步不可逆还原为Y(0)、Co(0)和Mg(0).在301 K时,利用循环伏安法分别测定出Mg(ClO4)2-LiClO4-DMF中Mg(Ⅱ)的扩散系数和传递系数为2.95×10－6 cm2•s－1和0.11；CoCl2-LiClO4-DMF中Co(Ⅱ)的扩散系数和传递系数为1.34×10－5 cm2•s－1和0.24；Y(NO3)3-LiClO4-DMF中Y(Ⅲ)的扩散系数和传递系数为1.68×10－5 cm2•s－1和0.10.在铜电极上于－1.50～－3.00 V(vs SCE)下恒电位电沉积,得到黑色、光滑致密、粘附性好的Y-Mg-Co合金膜,其中Y含量为3.88％～58.66％;Mg含量为4.51％～17.52％.     

钴铂合金薄膜的循环伏安电沉积及其异常红外性能研究

运用循环伏安电沉积在玻碳基底上制得纳米结构钴铂合金薄膜,扫描电子显微镜和X-射线能量散射谱研究表明,钴铂薄膜主要由平均粒经为139 nm的纳米粒子组成,钴和铂的原子比为3:5. 以CO为探针分子,电化学原位FTIR反射光谱研究发现钴铂薄膜具有异常红外效应. 吸附态CO发生异常红外吸收,谱峰比本体钴和铂分别增强了34和43倍.     

NiII36-Containing 54-Tungsto-6-Silicate: Synthesis,Structure, Magnetic and Electrochemical Studies

The 36-Ni^II-containing 54-tungsto-6-silicate, [Ni₃₆(OH)₁₈(H₂O)₃₆(SiW₉O₃₄)₆]⁶⁻ ( Ni₃₆ ) was synthesized by a simple one-pot reaction of the Ni₂-pivalate complex [Ni₂(μ-OH₂)(O₂CCMe₃)₄(HO₂CCMe₃)₄] with the trilacunary [SiW₉O₃₄]¹⁰⁻ polyanion precursor in water and structurally characterized by a multitude of physicochemical techniques including single-crystal XRD, FTIR, TGA, elemental analysis, magnetic and electrochemical studies. Polyanion Ni₃₆ comprises six equivalent {Ni^II₆SiW₉} units which are linked by Ni−O−W bridges forming a macrocyclic assembly. Magnetic studies demonstrate that the {Ni₆} building blocks in Ni₃₆ remain magnetically intact while forming a hexagonal ring with antiferromagnetic exchange interactions between adjacent {Ni₆} units. Electrochemical studies indicate that the first reduction is reversible and associated with the W^VI/V couple, whereas the second reduction is irreversible attributed to the Ni^II/0 couple.     

PtCr合金的溶液制备及其电化学性质分析

催化剂性能的高低直接决定了燃料电池性能的好坏. 采用Pt基合金不仅能够降低催化剂Pt的载量, 而且往往能够提高催化剂的性能. 本工作用Cr作为合金化元素, 通过液相共沉淀的方式制备了不同比例的碳载PtCr合金催化剂. 采用高分辨透射电镜(HRTEM), 扫描电镜(SEM)等技术对合金催化剂的物理性质进行了测试. 结果表明, 获得的PtCr/C催化剂均匀地分散在Vulcan XC-72碳载体上, 粒度小于4 nm. 通过电化学测试, 研究了不同比例PtCr合金的电化学催化性能. 循环伏安测试表明, 本实验条件合成的合金催化剂在Pt/Cr原子比为2/1的时候, 对氧还原动力学有最佳的催化性能.     

One‐step Synthesis of AuAg Alloy Nanodots and its Electrochemical Studies towards Nitrobenzene Reduction and Sensing

Efficient, stable, and low‐cost electrocatalysts for the degradation and sensing of environment pollutants are essential components of clean environment monitoring. Here we report, one‐step synthesis and characterization of 1–3 nm diameter sized bi‐metallic AuAg nanodots (NDs) embedded in amine functionalized silicate sol‐gel matrix (SSG) and its electrochemical studies toward nitrobenzene. The SSG was used as a reducing agent as well as stabilizer for the prepared mono‐ and bi‐metallic nanoparticles (NPs). From the HRTEM, STEM‐EDS and XPS analyses, the bi‐metallic AuAg NDs were identified as an alloy and not the mixtures of Au and Ag NPs. Characteristic surface plasmon resonance (SPR) band between the Au and Ag NPs SPR absorption region was noticed for the prepared AuAg NDs. The AuAg alloy NDs with different concentrations of Au and Ag (Au₂₅Ag₇₅, Au₅₀Ag₅₀ and Au₇₅Ag₂₅ NDs) modified electrodes exhibited synergistic electrocatalytic effect than did the Au and Ag NPs towards nitrobenzene reduction and detection. Together with ultra‐small size and exceptional colloidal stability features within these SSG‐AuAg NDs pave convenient way for nanotechnology‐based catalysts development and sensor applications.     

模板法合成金银核壳纳米线及电化学表征

采用氧化铝模板由交流电沉积制备纯银纳米线.然后借助化学还原法,在已制备好的银线表面包裹不同厚度的金壳层,得到具有核壳结构的AgcoreAushell复合纳米线.电子显微镜(SEM,TEM)显示该复合结构纳米线表面形貌与加入的金盐量有关,而且包裹层较薄的复合纳米线表面存在大量的孔洞.循环伏安测试表明,具有孔洞效应的复合纳米线经多次循环扫描后即可过渡到无孔洞效应的表面.以对巯基苯胺(PATP)作为探针分子的表面增强拉曼光谱,可用于表征纳米材料的表面结构.     

Template Synthesis and Magnetic Behavior of FeNi Alloy Nanotube Arrays

"FeNi nanotubes were successfully prepared in pores of anodic aluminium oxide templates by the wetting template method. By varying the deposition conditions and the parameters of the templates, the lengths and the outer as well as the inner diameters of the tubes can be tailored. The FeNi nanotubes and their arrays were characterized by transmission and scanning electron microscopy. Macroscopic magnetic measurements show the FeNi nanotube arrays to have obvious anisotropy, and the easy axis is parallel to the nanotube axis. The magnetic moment distributions in the tube walls and the magnetization reversal mechanism are discussed. Magnetic moments of the FeNi nanotube preferentially lie in the nanotube wall, but the distribution is spatially isotropic. These magnetic behaviours are due to the unique shape of the nanotube."     

Pt-Ru合金薄膜的电沉积制备及其电化学表面增强红外吸收光谱

在1mmol·L-1H2PtCl6+1mmol·L-1RuCl3+0.1mol·L-1H2SO4镀液中采用电沉积法在化学镀金膜的红外窗口Si反射面上制备Pt50Ru50合金电极.利用原子力显微镜(AFM)可以观察到制备的Pt50Ru50合金电极形貌呈现出100-200nm大小的颗粒.常规电化学分析方法得出该电极具有典型的合金特征,对CO和CH3OH具有很好的催化氧化作用.应用电化学现场衰减全反射表面增强红外光谱法(ATR-SEIRAS)可以观察到该电极上Pt位和Ru位上CO的振动谱峰,且表现出Pt-Ru二元金属良好的协同催化性能.     

液相热分解纳米铁镍合金的形貌可控合成及其磁学性能研究

以Fe(CO)₅和Ni(HCOO)₂为前驱物,十八烯为溶剂,在表面活性剂和分散剂油酸和油胺的协同作用下,通过前驱体的液相热分解和自合金化,制备铁镍合金纳米颗粒。通过XRD和TEM研究了产物的微观结构,并对产物的磁学性质进行了表征。结果表明,在反应温度为200 ℃,油胺与油酸及甲酸镍的物质的量比为4∶2∶1,反应时间为20 min时可得形貌可控、抗氧化性强的面心立方晶体结构的平面三角形纳米铁镍合金,晶粒尺寸为15~55 nm。磁性测量表明,300 K时三角形形貌铁镍合金的饱和磁化强度为15.5 emu·g^-1,矫顽力趋近于零,呈现超顺磁性;在低温(4.2 K)时,铁镍合金的饱和磁化强度为17.5 emu·g^-1,矫顽力增大明显。     

Dealloying of Mesoporous PtCu Alloy Film for the Synthesis of Mesoporous Pt Films with High Electrocatalytic Activity

Mesoporous Pt film with highly electrocatalytic activity is successfully synthesized by dealloying of mesoporous PtCu alloy film prepared through electrochemical micelle assembly. The resulting mesoporous electrode exhibits high current density and superior stability toward the methanol oxidation reaction.     

Fe-Co-Ni合金纳米线有序阵列的模板合成与磁性

以二次阳极氧化的氧化铝膜为模板，用电化学沉积的方法成功地合成了Fe-Co-Ni三组份有序纳米线阵列.扫描电子显微镜（SEM）和透射电子显微镜(TEM)观察表明纳米线表面光滑、有序、高长径比；磁性测量表明,其矫顽力较同组份的膜材料有较大的提高.将样品在惰性气体氛围中不同温度下退火，随着退火温度增加，其纵向矫顽力有一个极值，而对应的横向矫顽力没有类似的变化，关于这一现象的机理,本文进行了初步的讨论. 图5参15     

Synthesis and Optical and Electrochemical Studies on Dicationic Fluorenophanes

The synthesis of 2,7-bridged dicationic fluorenophanes consisting of benzimidazole, imidazole, and benzotriazole units and their absorption, photoluminescence, and electrochemical behavior are described.     

Synthesis and Magnetic Property of Fe-B Amorphous Alloy Nanowires by Inducing DC Magnetic Field

One dimension (1D) Fe-B amorphous alloy nanowires with diameter of 50-80 nm and length of several micrometers were synthesized under weak DC (direct current) magnetic field by KBH₄ reducing in aqueous solution. The structure, composition, and morphology were characterized by X-ray diffraction (XRD), inductively coupled plasma atomic emission spectrometry (ICP-AES), and scanning electron microscope (SEM), respectively. The results revealed that the magnetic field led to the fabrication of Fe-B amorphous alloy nanowire structure. Vibrating sample magnetometer (VSM) has been used to detect the magnetic properties of the samples. The results showed that the inducing of magnetic field had obvious effect on the magnetic properties of the samples.     

磁场诱导制备Fe-B非晶态合金纳米线及其磁学性质

通过引入外加直流电磁场, 采用KBH4还原法在室温下制备了一维Fe-B非晶态合金纳米线, 并采用X射线衍射(XRD)、电感耦合等离子原子发射光谱仪(ICP-AES)和扫描电子显微镜(SEM)等表征方法研究了产物的结构、组成和形貌. 结果表明, 在直流电磁场的作用下得到了Fe-B非晶态合金纳米线, 所得样品的直径在50-80 nm之间, 长度达到数微米. 通过振动样品磁强计(VSM)研究其磁学性质, 发现外加磁场的引入会显著影响Fe-B非晶态合金的磁学性质. 随着引入磁场强度的增强, 所得样品的饱和磁感应强度和矫顽力明显区别于未引入磁场制备的Fe-B非晶态合金.     

氧化石墨掺杂的电化学活性自支撑聚苯胺膜

以氧化石墨（GO）为掺杂剂和模板,采用化学原位聚合法并通过调节苯胺单体和氧化石墨的质量比,合成了层状结构的聚苯胺/氧化石墨(PANI/GO)层状结构的自支撑膜。SEM和XRD研究表明,当苯胺单体与GO的质量比为67:1时,PANI/GO复合材料具有层间距~1.36 nm的层状结构,证实 GO的模板功能。XPS和FTIR研究表明PANI/GO复合材料中的典型的聚苯胺的掺杂态,进一步证实GO的掺杂功能。此外,电化学和热失重测量表明PANI/GO层状结构的自支撑膜呈现良好的热稳定性和高电化学活性.