合成反铁磁Ni81Fe19/Co90Fe10/Ru/Co90Fe10/Ni81Fe19的研究

采用直流磁控溅射方法制备了一系列的合成反铁磁及以其为自由层的自旋阀.研究发现,在Ni₈₁Fe₁₉与Ru层之间插入适当厚度的Co₉₀Fe₁₀层后,可有效地提高合成反铁磁两磁性层间的反铁磁耦合强度,得到具有饱和场H_s更高、饱和磁化强度M_s更低、热稳定性更好的合成反铁磁.另外,以这种合成反铁磁作自旋阀的自由层时,可有效提高自旋阀的稳定性. 关键词： 合成反铁磁 退火 自旋阀     

The magnetoelectric effect in layered composites Ni0.4Zn0.6Fe2O4—Pb0.95Sr0.05Zr0.53Ti0.47O3

The magnetoelectric effect in two- and three-layered composites based on nickel-zinc ferrite and lead zirconate-titanate was investigated. The value of the magnetoelectric response in layered composites depends largely on the frequency of the alternating magnetic field, the volume ratio of the electric phase forming the composite, and the mechanical interaction between magnetostriction and piezoelectric layers.     

π+π+ and π+π? Colliding in Noncommutative Space

By studying the scattering process of scalar particle pion on the noncommutative scalar quantum electrodynamics, the non-commutative amendment of differential scattering cross-section is found, which is dependent of polar-angle and the results are significantly different from that in the commutative scalar quantum electrodynamics, particularly when cosθ∼±1. The non-commutativity of space is expected to be explored at around Λ_NC∼TeV.     

High-resolution study of the ν1/ν5 and 2ν1/ν1+ν5 P-H stretching bands of PH2D

The P-H stretching bands ν₁/ν₅ and 2ν₁/ν₁+ν₅ were recorded using a Bruker 120 HR interferometer with a resolution of 0.0042 and 0.0088 cm⁻¹, respectively, and analyzed. From the fits 33 and 50, respectively, vibrational, rotational, centrifugal distortion, and resonance interaction parameters were obtained. These reproduce 668 and 497 rovibrational energies of the pairs of states ν₁/ν₅ and 2ν₁/ν₁+ν₅ with experimental accuracies, rms=0.00016 and , respectively. “Local mode” behavior of the PH₂ fragment is established and discussed in detail.     

CO2同位素分子16O12C16O, 16O12C17O, 16O13C17O配分函数研究

本文主要研究了CO2的三种同位素分子16O12C16O , 16O12C17O ,16O13C17O 70 K~6000 K的总内配分函数 (TIPS)。在总内配分函数的计算中, 转动配分函数的计算采用了McDowell的解析式法, 振动配分函数则采用了简谐振动近似(HOA)获得。最后通过将两配分函数乘积近似计算得出TIPS, 并将其70~3000 K的数据和HITRAN04数据进行了比较, 发现所得结果和数据库符合的较好, 且其误差可以近似看成一条直线。并通过对误差的拟合修订了高温区(3000~6000 K)的计算数据, 给出了在高温下的较为准确的TIPS值。     

BaB2O4-K2O和BaB2O4-K2B2O4赝二元系相图的研究

用X射线衍射和差热分析方法研究了BaB₂O₄-K₂O和BaB₂O₄-K₂B₂O₄赝二元系的相平衡关系。BaB₂O₄-K₂B₂O₄属共晶体系,共晶温度为850±3℃,共晶点成分为45mol％K₂O。在Ba 关键词：     

BaO-Li2O-B2O3三元系中BaB2O4-Li2B2O4和BaB2O4-Li2O截面相平衡关系的研究

本文用X射线和差热分析方法对BaO-Li₂O-B₂O₃三元系中的两个截面:BaB₂O₄-Li₂B₂O₄和BaB₂O₄-Li₂O作了研究。在BaB₂O₄-Li₂B₂O₄赝二元系中发现了一个新的化合物4BaB₂O₄·Li₂B₂O₄。化合物在930±3℃由包晶反应形成,并与Li₂B₂O₄形成共晶反应。共晶温度为797±3℃,共晶点组分为79mol％Li₂B₂O₄。在BaB₂O₄-Li₂O截面中也存在化合物4BaB₂O₄·Li₂B₂O₄,其包晶反应温度从930±3℃随Li₂O含量增加下降到908±3℃。在组分60mol％Li₂O处形成另一个新的化合物2BaB₂O₄·3Li₂O。该化合物在630±3℃也是由包晶反应形成,并与Li₂O和Li₂CO₃分别形成共晶反应,共晶温度分别为400±3℃和612±3℃。在BaB₂O₄-Li₂B₂O₄和BaB₂O₄-Li₂O体系中都没有观察到固溶体。用计算机程序分别对化合物4BaB₂O₄·Li₂B₂O₄和2BaB₂O₄·3Li₂O的X射线粉末衍射图案进行了指标化,其结果:4BaB₂O₄·Li₂B₂O₄的空间群为Pmma,a=13.033?,b=14.630?,c=4.247?,每个单胞包含两个化合式单位;2BaB₂O₄·3Li₂O的空间群为Pmmm,a=4.814?,b=9.897?,c=11.523?,每个单胞也含有两个化合式单位。 关键词：     

La2/3Ca1/3MnO3/Eu2CuO4/La2/3Ca1/3MnO3磁性隧道结的制备与表征

采用磁控溅射，紫外线光刻和离子束刻蚀制备了La_2/3Ca_1/3MnO₃/Eu₂CuO₄/La_2/3Ca_1/3MnO₃磁性隧道结.通过对获得的磁性隧道结的I-V特性测量，发现非线性的I-V特性，显示结样品的隧穿特性.有趣的是发现在电极材料La_2/3Ca_1/3MnO₃的金属-绝缘体转变温度(Tp)以下，I-V曲线出现一个跳变.随着温度降低，开始出现跳变的临界电流增大，但是跳变都发生在同样的电压下～209mV.当电流增大或减小在跳变点附近出现回滞.这一跳变只发生在铁磁金属态，表明这是一个磁性相关联的效应，可能对应一种新的磁性开关过程.虽然，目前对这一现象背后的物理机理还不清楚，但是，这一现象有可能在未来自旋电子学器件方面具有潜在的应用价值. 关键词： 庞磁电阻 磁性隧道结 开关效应     

Measurement of the decayτ? →ρ?ντ

An analysis of the decay ^--0 v has been performed using the ARGUS detector at the DORIS II storage ring. The branching ratio has been determined to be Br(^--0 v =(22.6±0.4±0.9)%. The shape of the ^-0 invariant mass spectrum is found to be in good agreement with the predictions obtained using the conserved vector current (CVC) hypothesis, suggesting that the ^-0 system is produced in aJ ^P=1^– state. An analysis of the measured decay angular distribution of the pions with respect to the flight direction of the ^-0 system demonstrates the vector nature of the coupling at the v vertex. With the assumption of zerov mass thev spin has been shown to be .Supported by the German Bundesministerium für Forschung und Technologie, under contract number 054DO51 P     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.     

Optical properties of (ZnO)0.5(P2O5)0.5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Binary (ZnO)_0.5(P₂O₅)_0.5 glasses doped with Eu₂O₃ and nanoparticles of Gd₂O₃:Eu were prepared by conventional melt-quench method and their luminescence properties were compared. Undoped (ZnO)_0.5(P₂O₅)_0.5 glass is characterized by a luminescent defect centre (similar to L-centre present in Na₂O-SiO₂ glasses) with emission around 324 nm and having an excited state lifetime of 18 ns. Such defect centres can transfer the energy to Eu³⁺ ions leading to improved Eu³⁺ luminescence from such glasses. Based on the decay curves corresponding to the ⁵D₀ level of Eu³⁺ ions in both Gd₂O₃:Eu nanoparticles incorporated as well as Eu₂O₃ incorporated glasses, a significant clustering of Eu³⁺ ions taking place with the latter sample is confirmed. From the lifetime studies of the excited state of L-centre emission from (ZnO)_0.5(P₂O₅)_0.5 glass doped with Gd₂O₃:Eu nanoparticles, it is established that there exists weak energy transfer from L-centres to Eu³⁺ ions. Poor energy transfer from the defect centres to Eu³⁺ ions in Gd₂O₃:Eu nanoparticles doped (ZnO)_0.5(P₂O₅)_0.5 glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between luminescent centre and Eu³⁺ ions.     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

过渡族元素掺杂BaTiO3-Tb1-xDyxFe2-y层状复合材料中的磁电效应

用溶胶-凝胶法制备1.0%mol Mn,Cr,Co掺杂 BaTiO₃(BTO)粉体,在1350℃下烧结成多晶陶瓷样品.X射线衍射和差示扫描量热分析表明,室温下掺杂BaTiO₃具有四方钙钛矿结构;居里点和相变潜热随Cr,Mn,Co掺杂逐渐降低.将掺杂BaTiO₃与Tb_1-xDy_xFe_2-y(TDF)胶合制成双层磁电复合材料,并研究了Cr:BTO-TDF,Mn∶BTO-TDF,Co:BTO-TDF层状复合材料中的磁电效应.实验表明,在340×80 A·m^-1偏置磁场下, Cr:BTO-TDF的横向磁电电压系数达到最大值586 mV·cm^-1·(80 A·m^-1)^-1.在400×80 A·m^-1偏置磁场下,Mn∶BTO-TDF和Co:BTO-TDF的横向磁电电压系数的最大值分别为480 mV·cm^-1·(80 A·m^-1)^-1和445mV·cm^-1·(80 A·m^-1)^-1.研究表明掺杂BaTiO₃-TDF层状复合材料中具有较强的磁电耦合.作为无铅压电材料,掺杂BaTiO₃制备的磁电效应器件颇具应用前景. 关键词： 磁电效应 双层复合材料 3')" href="#">掺杂BaTiO₃ 1-xDy_xFe_2-y')" href="#">Tb_1-xDy_xFe_2-y     

Bulk and surface properties of spinel Co3O4 by density functional calculations

DFT calculations are employed to bulk and surface properties of spinel oxide Co₃O₄. The bulk magnetic structure is calculated to be antiferromagnetic, with a Co²⁺ moment of 2.631 μ_B in the antiferromagnetic state. There are three predicted electron transitions O(2p) → Co²⁺(t_2g) of 2.2 eV, O(2p) → Co³⁺(e_g) of 2.9 eV and Co³⁺(t_2g) → Co²⁺(t_2g) of 3.3 eV, and the former two transitions are close to the corresponding experimental values 2.8 and 2.4 eV. The naturally occurring Co₃O₄ (1 1 0) and (1 1 1) surfaces were considered for surface calculations. For ideal Co₃O₄ (1 1 0) surfaces, the surface relaxations are not significant, while for ideal Co₃O₄ (1 1 1) surfaces the relaxation of Co²⁺ cations in the tetrahedral sites is drastic, which agrees with the experiment observation. The stability over different oxygen environments for possible ideal and defect surface terminations were explored.     

钴改性Fe3O4-MnO2催化转化生物质合成气制备液体燃料

本文制备了用于费托合成反应的钴改性Fe₃O₄-MnO₂双功能催化剂,并探究了钴负载量对Fe-Co协同效应的影响以及Fe₁Co_xMn₁催化剂的费托合成反应性能. 实验发现,在Fe₃O₄-Mn催化剂中加入Co可促进铁氧化物的还原、增加反应过程中铁位点的活性. 此外,Co的加入可增强Fe-Co金属间的电子转移,加强两者的协同作用,提高催化性能. Co负载较高的Fe₁Co_xMn₁催化剂可进一步促进加氢反应能力,使产品分布向短链烃方向转移. 在280 ^°C、2.0 MPa和3000 h^-1的最佳工况条件下,Fe₁Co₁Mn₁催化剂的液体燃料收率最高.     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

调控氧空位实现高比表面积Co3O4纳米片上的产氧反应

Electrochemical water splitting requires efficient water oxidation catalysts to accelerate the sluggish kinetics of water oxidation reaction. Here, we designed an efficient Co₃O₄ electrocatalyst using a pyrolysis strategy for oxygen evolution reaction (OER). Morphological characterization confirmed the ultra-thin structure of nanosheet. Further, the existence of oxygen vacancies was obviously evidenced by the X-ray photoelectron spectroscopy and electron spin resonance spectroscopy. The increased surface area of Co₃O₄ ensures more exposed sites, whereas generated oxygen vacancies on Co₃O₄ surface create more active defects. The two scenarios were beneficial for accelerating the OER across the interface between the anode and electrolyte. As expected, the optimized Co₃O₄ nanosheets can catalyze the OER efficiently with a low overpotential of 310 mV at current density of 10 mA/cm² and remarkable long-term stability in 1.0 mol/L KOH.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.