Long-term performance of poly(vinyl chloride) cables, Part 2: Migration of plasticizer

Cable samples with plasticized poly(vinyl chloride) insulations were aged in air at temperatures between 80 and 155 °C. The concentrations of the plasticizer (di-(2-ethylhexyl) phthalate, DEHP) in the insulations of the aged cables were determined by extraction of samples in tetrahydrofuran followed by analysis of the extract by liquid chromatography. The plasticizer concentration data for different ageing times were analysed by numerical methods, fitting Fick's second law with a concentration-dependent diffusivity. The analysis showed that the transport of the plasticizer to the surrounding air phase was controlled by diffusion at 120 and 155 °C with an activation energy of 89 kJ mol⁻¹. The evaporation of the plasticizer from the outer boundary was rate controlling at lower temperatures (≤100 °C). The rate of evaporation was initially constant and independent of the plasticizer concentration at both 80 and 100 °C. The activation energy for the initial DEHP loss rate from PVC at these temperatures was the same as that obtained for evaporation of pure DEHP on a glass plate at 60-100 °C measured by thermogravimetry, 98 ± 2 kJ mol⁻¹. Furthermore, the evaporation rate of pure DEHP on a glass plate was also of the same order of magnitude as the rate of plasticizer loss from the cable insulation. Extrapolation of the plasticizer loss rate data (from the cable at 80 °C and from pure liquid DEHP at temperatures between 60 and 100 °C) to 25 °C predicted a maximum loss of plasticizer of 1% over 25 years. This is in accordance with earlier presented data and with the data presented in this report.     

Thermal degradation kinetics of the biodegradable aliphatic polyester, poly(propylene succinate)

The preparation of the biodegradable aliphatic polyester poly(propylene succinate) (PPSu) using 1,3-propanediol and succinic acid is presented. Its synthesis was performed by two-stage melt polycondensation in a glass batch reactor. The polyester was characterized by gel permeation chromatography, ¹H NMR spectroscopy and differential scanning calorimetry (DSC). It has a number average molecular weight 6880 g/mol, peak temperature of melting at 44 °C for heating rate 20 °C/min and glass transition temperature at −36 °C. After melt quenching it can be made completely amorphous due to its low crystallization rate. According to thermogravimetric measurements, PPSu shows a very high thermal stability as its major decomposition rate is at 404 °C (heating rate 10 °C/min). This is very high compared with aliphatic polyesters and can be compared to the decomposition temperature of aromatic polyesters. TG and Differential TG (DTG) thermograms revealed that PPSu degradation takes place in two stages, the first being at low temperatures that corresponds to a very small mass loss of about 7%, the second at elevated temperatures being the main degradation stage. Both stages are attributed to different decomposition mechanisms as is verified from activation energy determined with isoconversional methods of Ozawa, Flyn, Wall and Friedman. The first mechanism that takes place at low temperatures is auto-catalysis with activation energy E = 157 kJ/mol while the second mechanism is a first-order reaction with E = 221 kJ/mol, as calculated by the fitting of experimental measurements.     

Thermal treatment of whewellite—a thermal analysis and Raman spectroscopic study

Thermal transformations of natural calcium oxalate monohydrate known in mineralogy as whewellite have been undertaken using a combination of thermal analysis and Raman microscopy with the use of a thermal stage. High resolution thermogravimetry shows that three mass loss steps occur at 162, 479 and 684 °C.Evolved gas mass spectrometry shows that water is evolved in the first step and carbon dioxide in the second and third mass loss steps. The changes in the molecular structure of whewellite can be followed by the use of the in situ Raman spectroscopy of whewellite at the elevated temperatures. The whewellite is stable up to around 161 °C, above which temperature the anhydrous calcium oxalate is formed. At 479 °C, the oxalate transforms to calcium carbonate with loss of carbon dioxide. Above 684 °C, calcium oxide is formed.     

Evaporative loss kinetics of di(2-ethylhexyl)phthalate (DEHP) from pristine DEHP and plasticized PVC

The migration of di(2-ethylhexyl)phthalate (DEHP) from poly(vinyl chloride) (PVC) to a surrounding gas phase at temperatures below 120 °C kinetically is controlled by evaporation. The effects on the DEHP loss rate of nitrogen flow rate, relative humidity and degradation of the plasticizer at 100 °C was assessed. The sample mass decreased linearly with time for both pristine DEHP and plasticized PVC at comparable rates, suggesting that a thin film of DEHP was present on the jacketing insulation during desorption. The latter hypothesis was supported by infrared spectroscopy and by the fact that DEHP is an amphiphilic molecule that will tend to aggregate at the surface with the hydrophobic 2-ethylhexyl units at the air interface. The effect on the migration rate of moisture present in the gas phase was negligible. The DEHP loss rate increased in a retarding non-linear fashion with increasing gas flow rate. In one of the experiments, DEHP was accidently degraded as revealed by discoloration, the presence of low molar mass degradation products (liquid chromatography) containing additional carbonyl groups (infrared spectroscopy) and an increase in the evaporation rate at temperatures between 100 and 130 °C.     

Pressurized liquid extraction as a novel sample pre-treatment for trace element leaching from biological material

Pressurized liquid extraction (PLE), commonly used for organic compounds extraction, has been applied for trace element leaching from marine biological material in order to determine major and trace elements (Al, As, Cd, Co, Cu, Fe, Hg, Li, Mn, Pb, Se, Sr, V and Zn). The released elements by formic acid PLE have been evaluated by inductively coupled plasma-optical emission spectrometry (ICP-OES). Different variables, such as formic acid concentration, extraction temperature, static time, extraction steps, pressure, mean particle size and diatomaceous earth (DE) mass/sample mass ratio were simultaneously studied by applying an experimental design approach (Plackett-Burman design (PBD) and central composite design (CCD)). Results showed that the extraction temperature was statistically significant (confidence interval of 95%) for most of the elements (high metal releasing was achieved at high temperatures). In addition, formic acid concentration was also statistically significant (confidence interval of 95%) for metals such as Cd and Cu. Most of the metals can be extracted using the same PLE operating conditions (formic acid concentration of 1.0 M, extraction temperature at 125 °C, static time of 5 min, one extraction step, extraction pressure at 500 psi and DE mass/sample mass ratio of 2). Taking in mind PLE requirements at the optimised operating conditions (125 °C), a time of 6 min is needed to pre-heat the cell. Therefore, the PLE assisted multi-element leaching is completed after 12 min. Analytical performances, such as limits of detection and quantification, repeatability of the over-all procedure and accuracy, by analysing GBW-08571, DORM-2, DOLT-3 and TORT-2 certified reference materials, were finally assessed.     

Alkylpolysiloxane glass capillary columns combining high temperature stability of the stationary liquid and deactivation of the surface

Summary A new method of making alkylpolysiloxane (OV 1, OV 101, OV 17, Dexsil 400, SE 52, SE 54) columns with high stability at temperatures above 300°C of both the stationary liquid itself (low bleeding) and of the surface deactivation (no tailing of polar solutes with extended use at temperatures beyond 250°C) is described. The best results were achieved on dealkalinized alkali glass but also on borosilicate surfaces which have been additionally HF treated before coating in both cases. The procedure can also be applied to leached alkali and borosilicate surfaces successfully. The best deactivations of the glass surface are attained in a two step procedure: firstly by treatment with gaseous HF/N₂ mixture and secondly by simple heating of the coated and closed column at temperatures between 350° and 450°C for several hours. The tailing behaviour of such columns for polar solutes is considerably improved by this procedure as shown by test chromatograms. The procedure can also be applied to leached alkali and borosilicate surfaces successfully.Extract also presented at the 8th National Meeting on Analytical Chemistry of the Swedish Chemical Society, Lund, June 1979 and at the 10th International Symposium on Chromatography and Electrophoresis, Venice, Italy, June 1979.     

Excess molar volumes of 1-nonanol withn-heptane at 25, 35 and 45°C1

The excess molar volumes V _m ^E at atmospheric pressure and at 25, 35 and 45°C for binary mixtures of 1-nonanol, with n-heptane have been obtained over the whole mole fraction range from densities measured with a vibrating-tube densimeter. The measurements at 25°C were extended to high dilution of 1-nonanol. The V _m ^E are sigmoid for the three temperatures, with a small maximum at low mole fractions of the alkanol. The absolute values of V _m ^E increase with temperature from 25 to 45°C.Communicated in part at the 4^th International Conference on Thermodynamics of Solution of Non-Electrolytes, Santiago de Compostela, Spain (1989).     

Glass capillary gas chromatography of highly polar solutes like diols,acids and amines deactivation of fused silica and pretreated alkali glass support surfaces

Summary The method of support surface deactivation by PSD (alkylpolysiloxane degradation) at temperature between 300 and 450°C previously described was used to deactivate both fused silica and alkali glass surfaces of capillary columns. The latter surfaces had to be pretreated before deactivation with aqueous HCl leaching or by the dealkalisation method using flowing HCl gas at 450°C and subsequent rinsing with water for alkali removal. Excellent alkylpolysiloxane columns with regard to tailing and irreversible adsorption of highly polar solutes have been obtained on both fused silica and the pretreated alkali glass. Fused silica does not require pretreatment before deactivation by the PSD-method, however. Good polyethyleneglycol (Carbowax 20 M) columns can also be obtained by coating the two types of surfaces when no deactivation is necessary. Deactivation by the PSD method cannot be applied in this case because polar stationary liquids do not adhere to alkylpolysiloxane deactivated surfaces. Sample capacity problems arising when separating highly polar solutes with non-polar stationary phases have also been investigated.     

Pretreatment of plant samples for the determination of Re by ICP-MS

In order to determine trace levels of rhenium in plant samples by ICP-MS, a pretreatment method was developed. Ten radish samples (Raphanus sativus L.) grown in solution culture containing ¹⁸⁴ReO₄ ^- were used. The samples were separated into three parts (leaves, fleshy root and fine roots), then each sample was oven-dried at 60 °C. The Re loss ratios in the samples after incineration at 450 °C for 3 hours and acid leaching at 90 °C for 3 hours were compared. There was no difference of recoveries among the sample parts, and throughout the procedure, almost 100% Re was recovered from the samples.     

Thermogravimetric analysis of composites obtained from sintering of rice husk-scrap tire mixtures

Summary The disposal of used automotive tires has caused many environmental and economical problems to most countries. We propose the use of rice husk as filler for increasing the value of recycled tire rubber. Thermal degradation of both components and their sintering mixtures is presented in this paper. Thermal decomposition of rice husk occurs in various steps in the temperature range between 150 and 550°C. This complex process is the result of the overlapping of thermal decomposition of the three major constituents common in all lignocellulosic materials, i.e., hemicellulose, lignin and cellulose. Hemicellulose is degraded at temperatures between 150 and 350°C, cellulose from 275 to 380°C and lignin from 250 to 550°C. The degradation process of major constituents of scrap tires or their composites is observed at temperatures between 150 and 550°C. For composites, the addition of rice husk (maximum 25%) produces an increase in the mass loss rate. This effect is higher as the amount of rice husk increases. However, the degradation initial temperature of elastomeric matrix is not affected with addition of rice husk. Apparent kinetic parameters were also studied by the isoconversional Friedman method. We observed that the addition of rice husk produces a decrease in apparent activation energy for low conversions (up to 0.6). For higher conversions this decrease was not so clearly observed.     

Facetting of Fe-15% Cr-N, Fe-3% V-C and Fe-3% V-C,N (111) surfaces

Summary Auger electron spectroscopy (AES), low energy electron diffraction (LEED) and scanning electron microscopy (SEM) have been used to study the surface chemistry of crystallographically open bcc (111) surfaces of Fe-15% Cr-N, Fe-3% V-C and Fe-3% V-C,N alloys. The binary and ternary surface phases CrN, VC and V(C,N) were formed at temperatures ranging from 450 to 750°C depending on the alloy. On Fe-15% Cr-30ppmN (111) two-dimensional surface compounds CrN were formed at temperatures above 600°C according to the bulk phase diagram of the Fe-Cr-N system, whereas on Fe-15% Cr-N samples with nitrogen contents of more than about 100 ppm the precipitation of three-dimensional CrN took place at temperatures below 600°C. Optical and SEM micrographs as well as oxidation experiments at room temperature indicated that the substrate surfaces are inhomogeneously covered by the surface phases. Facetting of the bcc (111) surfaces induced both by cosegregation of the solutes and by surface precipitation was observed in real space (SEM) as well as in reciprocal space (LEED). It is shown that the surface phases are epitaxially arranged on (100) facets of the substrate.     

Synthesis, characterization, and thermal properties of new silarylene-siloxane-acetylene polymers

New silarylene-siloxane-acetylene polymers have been synthesized by coupling reactions employing 1,3-bis(p-ethynylphenyl)-1,1,3,3-tetraphenyldisiloxane (3) as the key monomer. Their thermal properties have been evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). All of the new polymers showed good thermal stability, with their temperatures at 5% weight loss (T_d5) being higher than 540 °C under nitrogen and higher than 460 °C in air. Their char yields at 1000 °C under N₂ were above 80%. Broad exothermic peaks, attributable to reaction of the acetylenic units, were observed by DSC analysis in the temperature range 270-450 °C.     

Preparation of Copolymerized Phenylsilsesquioxane-Benzylsilsesquioxane Particles

Copolymerized phenylsilsesquioxane-benzylsilsesquioxane particles were prepared from their corresponding organotriethoxysilanes by the sol-gel method. Transparent thick films of a few microns in thickness have been successfully prepared on glass substrates coated with indium tin oxide (ITO) by heat-treating the copolymerized particles which had been electrophoretically deposited on the substrates. The on-set temperature for thermal sintering of the copolymerized particles decreased from 150 to 50°C with increasing the benzylsilsesquioxane content. These on-set temperatures for thermal sintering of the particles were found to be higher by 10 to 50°C than the glass transition temperatures of the particles of the corresponding composition. The thermal sintering of the particles should occur due to a large decrease in viscosity of the particles at temperatures higher than the glass transition temperatures. The decrease in the on-set temperature with composition for thermal sintering as well as in the glass transition temperature of the particles can be related with the decreases in average molecular weight and in distribution of the molecular weight of the particles with an increase in the benzylsilsesquioxane content.     

MoS x Thin Films by Thermolysis of a Single-Source Precursor

Thin films of MoS _x have been prepared on silicon substrates by spin coating and thermolysis of 0.5 M solutions of alkyldiammonium tetrathiomolybdates in 1,2-ethanediamine (EDA) and 1,2-propanediamine (12PDA). The films have been heat treated in air at temperatures between 80 and 250°C and under N₂ atmosphere at temperatures between 300 and 800°C. X-ray diffraction shows a restricted crystallisation and amorphous residues in both kind of films. EDA-based films exhibit a high tendency to crystallise whereas 12PDA-based films form associated structures with the solvent preventing precursor crystallisation. An insight into the processes occurring in film formation is gained by infrared spectroscopy which indicates a beginning of the decomposition of the 12PDA-based film at temperatures as low as 80°C with incorporation of the diamine solvent. In contrast, the EDA-based films show first signs of a decomposition at 150°C. The decomposition of the intermediate MoS₃ in both cases starts between 250 and 300°C. By means of SNMS depth profiles carbon contents up to 21 and 32 atom-% were found in EDA- and 12PDA-based films, respectively. The films show a significant deficit of sulphur which is compensated by the carbon. Near the surface of the coatings a loss of carbon is observed.     

Kinetics of the hydrolysis of bisphenol A diglycidyl ether (BADGE) in water-based food simulants

Summary The first-order degradation kinetics of bisphenol A diglycidyl ether (BADGE; CAS No. 1675-54-3) has been studied in three water-based food simulants (3% (W/V) acetic acid, distilled water and 15% (V/V) ethanol) at various temperatures. BADGE and its first and second hydrolysis products were determined by reversed-phase high-performance liquid chromatography with fluorescence detection. Nonlinear regression was used to fit the experimental data at 40, 50 and 60°C with the proposed kinetic equations; Arrhenius' equation was then fitted to the rate constants obtained and the kinetic models were tested by comparing experimental data obtained at 70°C with the kinetic curves calculated using the rate constants predicted for this temperature. The half-life of BADGE was longest in ethanol and shortest in acetic acid. The rings opening in acetic acid appears to happen by means of active hydrogens whereas in the other simulants it is mainly influenced by the formation of acid/base adducts. The results imply that resins which comply with existing legislation on the migration of unreacted monomer may still contaminate foodstuffs.     

Thermal decomposition products of copoly(arylene ether sulfone)s characterized by direct pyrolysis mass spectrometry

Pyrolysis products with mass of up to 850 Da were detected by direct pyrolysis mass spectrometric (DPMS) analysis of a series of copoly(arylene ether sulfone)s (PES-PPO) synthesized by nucleophilic condensation of either 4,4′-dichlorodiphenylsulfone (CDPS) or 4,4′-bis-(4-chlorophenyl sulfonyl) biphenyl (long chain dichloride, LCDC) with different molar ratios of hydroquinone (HQ) or dihydroxydiphenylsulfone (HDPS). Pyrolysis products retaining the repeating units of the initial copolymers were formed at temperatures ranging from 420 °C to 470 °C (near the initial decomposition temperature). At temperatures higher than 450 °C were observed products containing biphenyl units, formed by the elimination process of SO₂ from diphenyl sulfone bridges. Products having biphenyl and dibenzofuran moieties were detected in the mass spectra recorded at temperatures above 550 °C. These units were formed by loss of hydrogen atom from diphenyl ether bridges. Although the EI (18 eV) mass spectra of the pyrolysis products of the samples investigated were very similar, it was found that the relative intensity of some ions reflects the molar composition of the copolymers analysed. Cyclic and linear oligomers with very low molecular mass, present in the crude copolymers, were also detected by DPMS. Thermogravimetric analysis also showed their excellent thermal stability below 400 °C. It indicates that the copolymers yield a char residue of 40-45% at 800 °C, which increases with the PPO mole fraction in the samples.     

Microstructural and Dielectric Characterization of Sol-Gel Derived Silicon Oxycarbide Glass Sheets

Thin (50—1000 m) silicon oxycarbide glass sheets were synthesized by the pyrolysis of gel sheets obtained from a methyl-modified silica sol containing colloidal silica under inert atmosphere between 900 and 1450°C. The microstructure of these glass sheets was investigated with the help of high resolution scanning and transmission electron microscopy (HR-SEM and HR-TEM), X-ray diffraction and Raman spectroscopy and their dielectric properties were determined. The surface morphology as observed with HR-SEM did not exhibit a notable temperature dependence. HR-TEM studies showed that the glass sheets sintered up to 1200°C are amorphous, whereas those sintered at 1450°C contain uniformly dispersed crystallites of SiC and graphite. X-ray diffraction studies were found in agreement with the HR-TEM results. Raman spectroscopy showed that free carbon is present as an amorphous phase till a temperature of 1000°C, whereas at temperatures 1200°C, the presence of graphitic carbon was observed. Silicon oxycarbide glass sheets heat treated at temperatures up to 1200°C, showed a dielectric constant between 4.1 ± 0.11 and 4.6 ± 0.15 in the frequency range from 75 kHz to 5 MHz, with corresponding losses between 0.0008 and 0.1100. Such silicon oxycarbide glass sheets sintered at 1200°C could find an application as substrates for electronic packaging.     

Synthesis and characterization of elastic aliphatic polyesters from sebacic acid, glycol and glycerol

A series of biodegradable polyesters have been prepared from sebacic acid (SA), glycol (Go) and glycerol (Ge) through a two-step process. First the linear prepolymers were prepared from SA and Go, then crosslinked polyesters were obtained from the prepolymer and Ge with different molar ratios. The resulting samples were characterized by Fourier Transform Infrared Spectrum (FTIR), X-ray Photoelectron Spectroscopy (XPS), and Differential Scanning Calorimetry (DSC). Dynamic Contact Angle tests (DCA) and mechanical tests were also investigated. The enzymatic degradation studies were performed at 37 °C in phosphate buffer solution with porcine pancreas lipase. The resultant polyesters were transparent, flexible, insoluble in organic solvents, and the surfaces of the polyesters were hydrophilic. Young’s modulus, tensile strength, glass transition temperature (T_g) and the degree of enzymatic degradation increased with increasing the content of Ge. It was also worth noticing that the surface content of -COOC- groups was a key factor in the enzymatic degradability.     

Effects of the structure on the properties of new poly(arylene ether sulfone)s containing naphthalene units

A series of new poly(arylene ether sulfone)s has been obtained by solution condensation polymerisation starting from 1,5- and 2,6-bis-(4-fluorosulfonyl)naphthalene with various aromatic dihydroxy compounds. The polymers, obtained in quantitative yields, possessed inherent viscosities in the range 0.28-0.68 dl g⁻¹, had good thermal stability (10% weight loss temperatures were above 405 and 420 °C respectively in nitrogen and air) and high glass transition temperatures (in the range 217-258 °C). They have been characterised by elemental and infrared analyses, GPC and wide-angle X-ray diffraction. The properties of these poly(arylene ether sulfone)s have been compared with those of the corresponding poly(arylene ether ketone)s.     

Influence of a cooling rate on a structure of PA6

The structure of the plate specimens obtained from the molten PA6 that was cooled at rates between 2 and 2000 °C/min have been studied. The cooling rate of 2000 °C/min did not ensure a complete amorphization of the specimens. The amorphous phase created by supercooling is unstable and at room temperature undergoes a noticeable cold crystallization. The access of water to the specimen from the surrounding air accelerates this process.Variations in the cooling rate of the melt reflect in rearrangement of the amorphous phase of PA6. Owing to the effect of interaction with the crystalline phase, the amorphous regions undergo changes in molecular weight and MWD of the chain segments between junctions in topological regions, temperatures of the glass transition and β-relaxation, compaction, etc.