Characterization of lattice disorder in the low-temperature phase of irradiated PTFE by vibrational spectroscopy

In an effort to elucidate the structure of the low-temperature phase of PTFE, a spectroscopic study of the effect of progressive irradiation on the low-frequency infrared spectrum was undertaken. Previous infrared and Raman measurements indicated that irradiation of PTFE decreases its crystalline content, resulting in a lowering of the 19°C phase transition temperature due to the introduction of disorder and defect structures into the lattice by chain scission. Far-infrared studies of virgin and irradiated PTFE at liquid nitrogen temperatures show that the medium to strong bands at 45, 54, 58, and 71 cm^?1, attributed to lattice vibrations, decrease in intensity as the crystalline content decreases. These findings support the assignment of these bands to intermolecular vibrations of the crystalline lattice and are an indication of the presence of more than one molecule in the crystallographic unit cell.     

The thermal desorption mass spectra of polytetrafluoroethylene modified under the action of radiation at elevated temperatures

The products of the pyrolysis of polytetrafluoroethylene (PTFE) in a vacuum modified under the action of gamma irradiation in the molten state were studied mass spectrometrically at various temperatures. Radiation modification was found to cause the appearance of an additional stage of the thermal decomposition of PTFE at decreased temperatures compared with not irradiated PTFE. The chemical composition of the gas components of thermal decomposition substantially changes after the irradiation of PTFE, which increases the molecular weight of decomposition products. A comparison with the results of an additional study of the thermal decomposition of tetrafluoroethylene copolymer with hexafluoropropylene is evidence of the formation of side CF₃ groups in PTFE under irradiation. Data on the composition of gaseous products of PTFE radiolysis under gamma irradiation were obtained.     

Polytetrafluoroethylene: Effects of γ-radiation on fine structure

The structure of granular polytetrafluoroethylene has been studied by electron microscopy. On the basis of the texture of surfaces resulting from fracture a model of the structure is proposed which suggests that PTFE consists of extended chain crystals with both inter- and intra-lamellar noncrystalline regions. The effects of γ-radiation on the structure have been investigated by examining the texture of irradiated fracture surfaces and also the texture produced by post-irradiation fracture. The irradiations have been performed in vacuo and in oxygen. In both atmospheres PTFE undergoes degradation with a concurrent increase in crystallinity. However, the texture of the surfaces of high crystallinity PTFE, prepared by radiation, differs markedly to the texture of fracture surfaces of high crystallinity PTFE prepared by thermal annealing. It is proposed that radiation causes rupture of bonds in the interlamellar (chain fold) and intralamellar regions, resulting in the production of chain ends and interlamellar links. Due to scavenging of the free radicals, interlamellar linking is pobably a minor process with irradiation in oxygen. These chemical changes cause modifications to the extended chain lamellar crystals and consequently alterations to the physical properties of the polymer.     

Temperature influence on the stability and chemical composition of electron beam‐irradiated polytetrafluoroethylene

Polytetrafluoroethylene powder (PTFE) was exposed to electron beam radiation in presence of air. The irradiation mainly resulted in chain scission and induction of oxygenated groups and radicals as well as unsaturation. The thermal behavior of the irradiated PTFE and the fate of the radicals were studied comprehensively. Apart from fluorine, saturated and unsaturated fluorocarbons and oxygen‐containing groups were released during heating. Furthermore, irradiation‐generated peroxy radicals were transformed into alkyl radicals in a partly reversible process. A proposal for the complex reaction mechanisms of irradiated PTFE is given. The thermal stability of irradiated PTFE was improved by annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2404–2411, 1999     

Proton irradiation effects on the structural and tribological properties of polytetrafluoroethylene

Polytetrafluoroethylene (PTFE) was irradiated with protons in a ground-based simulation facility to study the effects of proton irradiation on the structural and tribological properties of PTFE. The structural changes were characterized by X-ray photoelectron spectroscopy (XPS) and attenuated total-reflection FTIR (ATR-FTIR), while the tribological properties were evaluated by friction and wear tests. It was found that proton irradiation induced the degradation of PTFE molecular chains, resulting in the increase of C concentration and the decrease in F concentration on the sample surfaces, and the surface chemical structure and morphology of the samples changed, which affected the friction coefficient and decreased the wear rate of the specimens as the friction and wear tests revealed.     

Thermal expansion of irradiated polytetrafluoroethylene

The thermal expansion coefficient of gamma-irradiated Polytetrafluoroethylene (PTFE) has been measured in the temperature range 80–340 K by using a three-terminal capacitance technique. The samples are irradiated in air at room temperature with gamma rays from a Co⁶⁰ source at a dose rate of 0.26 Mrad/h. The change in crystallinity is measured by an x-ray technique. The expansion coefficient is found to increase with radiation dose below 140 K owing to the predominant effect of degradation. Above 140 K, the expansion coefficient is found to decrease with radiation dose because of the enhanced crystallinity. The temperatures of the two first-order phase transitions are also found to shift to lower temperatures owing to degradation of PTFE.     

Smectic C phenylpyridines with an alkenyloxy chain

Abstract

The known 5-n-alkoxy-2-[4-(n-alkoxy)phenyl]pyridines exhibit high smectic C transition temperatures as well as various highly ordered smectic mesophases. An unsaturated carbon-carbon double bond has now been introduced into the terminal alkoxy chain of these heterocyclic materials to produce the corresponding alkenyloxy substituted derivatives. The postion and nature (E/Z) of the double bond has been varied systematically and the effect on the liquid crystal transition temperatures determined. A number of homologous series of the most promising alkenyloxy substituted materials has been prepared and evaluated. The position and nature (E/Z) of the double bond changes the conformation of the alkenyloxy chain to a significant degree. This can lead to slightly higher smectic C transition temperatures for compounds with a trans-double bond (E) at an even number of carbon atoms from the molecular core. However, the highly ordered mesophase transition temperatures are increased to a greater degree leading to a reduction in the smectic C temperature range. Significantly lower transition temperatures (including the melting point) are observed for materials with a cis-double bond (Z) at an odd number of carbon atoms from the molecular core. Comparisons with the corresponding alkoxy substituted materials (i.e. without a double bond) are made. These new alkenyloxy materials can be used to increase the smectic C and nematic transition temperatures of chiral mixtures for electrooptical display devices based on ferroelectric effects.     

Electron beam irradiation-induced transformations in the electrical properties of 4’-octyl-4-cyanobiphenyl (8CB)

Changes in the dielectric and thermodynamical properties of electron beam-irradiated 4′-octyl-4-cyanobiphenyl (8CB) were studied. Irradiation-induced changes in the phase transition temperature, dielectric anisotropy, relaxation frequency and activation energy of an observed non-collective relaxation mode corresponding to molecular rotation about the short axis were determined in both nematic and smectic A_d phases. In the nematic phase, dielectric anisotropy increased for a small dose but decreased for a relatively high dose, whereas the relaxation frequency increased due to the irradiation. The pure and irradiated samples were characterised by UV–visible spectroscopy, Fourier transform infrared spectroscopy, gas chromatography, gas chromatography coupled with mass spectroscopy and pulse radiolysis. The observed changes in the dielectric parameters are related to the detachment of the CN group from some of the 8CB molecules due to the electron beam irradiation.     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Grafting of styrene into pre-irradiated fluoropolymer films: Influence of base material and irradiation temperature

In this study, the influence of irradiation temperature on mechanical properties of three fluoropolymers and on grafting of styrene into the polymers by the pre-irradiation method was investigated. Electron paramagnetic resonance spectroscopy and infrared spectroscopy were used to characterize the irradiated polymers regarding trapped radical species and changes in the chemical structure, respectively. For poly(tetrafluoroethylene-co-perfluoropropyl vinyl ether) (PFA) the irradiation temperature was found to be an important factor for tensile strength and elongation at break of the pre-irradiated film. No strong effect of irradiation temperature on the mechanical properties was noticed for poly(tetrafluoroethylene-co-ethylene) (ETFE); however the yield of grafting drops at high irradiation temperatures. Finally, mechanical properties of poly(tetrafluoroethylene) (PTFE) were found to be dramatically altered, even if the film was irradiated at elevated temperature.     

Radiation effect on polystyrene deposited and grafted on silica gel

The effect of radiation on polystyrene was studied in the presence and absence of silica gel by molecular weight measurement with GPC. Polystyrene crosslinked under vacuum in the absence of silica gel, but it either crosslinked or degraded by radiation, depending on the molecular weight of the polymer in the presence of silica gel. Part of the deposited polymer bonded to silica gel by radiation; the G value for graft-chain formation is in the range of 0.01–0.1. Irradiation of polystyrene grafted on silica gel resulted in degradation of the graft chain because of the transfer of energy from silica gel. The G value for main chain scission was about 2 when graft polymer was irradiated in the absence of homopolymer. The degradation of graft polymer was suppressed when the polymer was irradiated in the presence of homopolymer, and the amount of unextractable polymer from silica gel increased with increasing irradiation. This adds evidence to the estimation that an increase in grafting percent coupled with a slight decrease in molecular weight at a later stage of radiation-induced polymerization of styrene adsorbed on silica gel is due to a secondary effect of radiation on the polymer.     

Surface modification of poly(tetrafluoroethylene) with benzophenone and sodium hydride by ultraviolet irradiation

Poly(tetrafluoroethylene) (PTFE) films were surface modified in a solution of benzophenone and sodium hydride in dry dimethylformamide by ultraviolet (UV) light irradiation. The extent of surface modification was characterized after durations of UV light irradiation from 5–20 min at temperatures from 19–60°C. The modified films were analyzed by electron spectroscopy for chemical analysis, diffuse reflectance ultraviolet-visible light spectroscopy, attenuated total reflection Fourier transform infrared spectroscopy, dynamic contact angle measurement, and low-voltage scanning electron microscopy. PTFE surfaces produced by this modification demonstrated extensive defluorination, oxygen incorporation, surface unsaturation, and reduction in both advancing and receding dynamic water contact angles in a manner that was more extensive at long durations of irradiation and at high temperatures. Morphological damage depended upon treatment conditions, but extensive surface modification could be obtained without substantial morphological damage to PTFE films. Control experiments indicated that the surface modification proceeded by photoexcitation of either diphenyl ketyl radical anion or benzhydrol anion, the products of reaction of benzophenone with sodium hydride. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1499–1514, 1997     

Thermal Analysis of the Poly(Siloxane)–Poly(Tetrafluoroethylene) Coating System

Thermal properties of poly(siloxane)–poly(tetrafluoroethylene) (SIL–PTFE) system were investigated, using Perkin Elmer DSC-7 differential scanning calorimeter and TGA-7 thermogravimetric analyzer. For SIL–PTFE compositions, one glass transition temperature T _g has been found, in accordance with the reciprocal rule up to about 40 mass% of PTFE. However, for higher PTFE contents, T _g values about –118 to –112°C were observed that can be ascribed to motions of cross-linked SIL structures. Endo- and exothermic transitions, found in the range from 70 to 290°C, not observed for pure SIL and PTFE components, are considered as specific ones for the SIL–PTFE semi-IPN structures. The SIL–PTFE system, as well as its components, is thermally stable, if degradation reactions are considered; the temperatures of decomposition at the maximum decomposition rate were above 530°C. It has been found that the thermal stability of the SIL–PTFE system is increasing with the increase of the PTFE content. This revised version was published online in August 2006 with corrections to the Cover Date.     

Surface properties of polymers treated with F2 laser

Selected polymers (polyethylene‐PE, polypropylene‐PP, polytetrafluoroethylene‐PTFE, polystyrene‐PS and polyethylenterephthalate‐PET) were irradiated with the linearly polarized light of a pulsed 157 nm F₂ laser. The irradiation results in degradation of polymers and ablation of polymer surfaces. Contact angle, measured by goniometry, was studied as a function of the number of laser pulses. The volume of the ablated polymer layer was determined by gravimetry. Changes in surface morphology and roughness were observed using atomic force microscopy. Surface chemistry of the samples was investigated by electrokinetic analysis and by XPS. While PET and PE exhibit small ablation, the ablation of PS and PTFE is more significant, and the most pronounced ablation is observed on PP. Contact angle of all polymers, with the only exception of PP, is a decreasing function of the number of laser pulses up to 2000 pulses. Laser irradiation leads to a refinement of the polymer surface morphology and a decrease of their surface roughness. Electrokinetic analysis and PS show changes in the surface chemistry of polymers after the laser treatment. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanistical studies on the electron-induced degradation of polymers: polyethylene, polytetrafluoroethylene, and polystyrene

Mechanisms of the electron-induced degradation of three polymers utilized in aerospace applications (polyethylene (PE), polytetrafluoroethylene (PTFE), and polystyrene (PS)) were examined over a temperature range of 10 K to 300 K at ultra high vacuum conditions (～10(-11) Torr). These processes simulate the interaction of secondary electrons generated in the track of galactic cosmic ray particles in the near-Earth space environment with polymer material. The chemical alterations at the macromolecular level were monitored on-line and in situ by Fourier-transform infrared spectroscopy and mass spectrometry. These data yielded important information on the temperature dependent kinetics on the formation of, for instance, trans-vinylene groups (-CH=CH-) in PE, benzene (C(6)H(6)) production in PS, fluorinated trans-vinylene (-CF=CF-) and terminal vinyl (-CF=CF(2)) groups in PTFE together with molecular hydrogen release in PE and PS. Additional data on the radiation-induced development of unsaturated, conjugated bonds were collected via UV-vis spectroscopy. Temperature dependent G-values for trans-vinylene formation (G(-CH=CH-) ≈ 25-2.5 × 10(-4) units (100 eV)(-1) from 10-300 K) and molecular hydrogen evolution (G(H(2)) ≈ 8-80 × 10(-5) molecules (100 eV)(-1) from 10-300 K) for irradiated PE were calculated to quantify the degree of polymer degradation following electron irradiation. These values are typically two to three orders of magnitude less than G-values previously published for the irradiation of polymers with energetic particles of higher mass.     

Molecular motion of ends of isolated poly(isobutylene) chains tethered on the poly(tetrafluoroethylene) surface in vacuo

Poly(isobutylene) (PIB) chains with a radical at the chain end were graft-copolymerized on the poly(tetrafluoroethylene) (PTFE) surface in vacuo at 77 K. The PIB chains tethered on the PTFE surface in vacuo were regarded as isolated chains from neighboring tethered PIB chains. The molecular motion of the ends of the isolated PIB chains was observed by an electron spin resonance (ESR) spectrometer in the temperature range from 3 to 125 K, which was lower than T_g of PIB, 200 K,¹ and two motion modes were found: One is a quantum tunneling of the methyl group located at the chain end at 3 K, and the other is an interconformation transition with freely rotating methyl group at the end at 77 K, where the transition rate was estimated to be 15 MHz at that temperature. The transition rate increased with an increase in temperature. The activation energy of the transition was estimated to be 370 J/mol. The high mobility and low activation energy was attributed to the isolation of PIB chains in vacuo. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2095–2102, 1998     

Structural modifications of polymers under the impact of fast neutrons

Fast neutron irradiations were performed at room temperature on a series of 13 polymer matrixes having great practical and academic interest. Polymers were irradiated with very low doses of 14 MeV neutrons deposited at reduced dose rate. The modifications of chemical structure of the polymeric matrixes resulting from irradiation were analyzed at the molecular scale by infrared and UV-visible spectroscopy. Particular attention was given to the oxidation occurring in irradiated matrixes during storage in the absence of light at room temperature. In addition the effects of irradiation on the chain arrangements in the polymers were analyzed by Differential Scanning Calorimetry.The most significant result obtained in this preliminary work was evidence that neutron irradiation with very low doses in the range ≈130-320 cGy could provoke structural changes. Indeed, depending on the matrixes, the formation of oxidation products along the macromolecular chains or the evolution of the polymer architecture, evidenced by changes of the T_g or of the crystallinity, was observed. The perspectives of this preliminary work are discussed.     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Poly(ethylene oxide) irradiated in the solid state,melt and aqueous solution—a DSC and WAXD study

Interactions of the aggregate state of poly(ethylene oxide), PEO, and γ-irradiation conditions (total dose, atmosphere) on its thermal and crystalline properties were investigated by DSC and WAXD taking into account sample molecular mass and form. In PEO irradiated in the solid state and in the presence of oxygen, chain scission dominated over concurrent crosslinking up to 200 kGy, particularly in PEO powders, due to a large surface being in contact with air. In solid samples the degree of crystallinity and crystallite size increased with the dose up to 50 kGy, probably not just due to partial crystallization upon degradation of amorphous phase, but to recrystallization of broken tie molecules. The least changes in crystallinity and phase transformation temperatures occurred in solid films. A substantial decrease in crystallinity and transformation temperatures without the initial crystallinity increase was achieved in samples that were amorphous on irradiation, at temperatures above the PEO melting temperature and in aqueous solutions. Radiation crosslinking of the PEO aqueous solution in an inert atmosphere is the most suitable way to obtain a lower degree of crystallinity and phase transformation temperatures while preserving mechanical properties.     

Mesomorphic behaviour of praseodymium(III) alkanoates

In this paper, we describe the synthesis, characterization and thermal behaviour of praseodymium(III) alkanoates. The compounds have the stoichiometry [Pr(C _x H_2x+1COO)₃], where x = 5-19, and were characterized by elemental analysis and infrared spectroscopy. The thermal behaviour was investigated by hot-stage polarizing optical microscopy, DSC and high temperature X-ray diffraction. A highly viscous mesophase M and a smectic A phase were observed for the shorter chain compounds (x = 5-8), whereas only a smectic A phase was observed for the longer chain compounds of this type of metallomesogens. The chain length has a pronounced effect on the transition temperatures.