Synthesis and characterization of acetylene-terminated aromatic amide resin precursors

A series of 10 acetylene-terminated aromatic amide monomers was synthesized by the triethylamine-promoted reaction of bis[p-(m-chlorocarbonylphenoxy)phenyl] sulfone or bis[p-(m-chlorocarbonylphenoxyl)phenyl]ketone with o- or p-ethynyl- and o- or p-trimethylsilylethynylaniline. Yields were essentially quantitative. Structures were verified by infrared and nuclear magnetic resonance spectroscopy and mass spectral data. Thermal characteristics of the monomers were investigated by means of differential scanning calorimetry and thermogravimetric analysis. The initial glass transition temperatures were generally well below the onset of cure which occurred in the 160–225°C range for the terminal ethynyl monomers and in the 260–295°C range for their trimethylsilylethynyl analogs. Onset of decomposition in air for the resinified terminal ethynyl monomers took place in the 400–485°C range, while resins from the trimethylsilylethynyl monomers underwent breakdown at substantially lower temperatures.     

Synthesis of （p—Substituted phenyl）azo Calix[4] arenes

A novel method for the preparation of chromogenic calixarenes with azo groups was reported.p-Substituted(-NO2,-CH3,-Cl)amilines were diazotized with isoamyl nitrite in EtONa/EtOH under refluxing condition.Fifteen mono-,bis-,tris-and tetrakis(p-substituted phenyl)azo calix[4]arenes (including proximal and distal isomers) were obtainged respectively by diazo-coupling in different molar ratio to calix[4]arenes(1) under pH=7.5-9.0 in non-aqueous solution at 0-5℃.^1H NMR and ^13C NMR spectra of (p-substtituted phenyl)azo calix[4]-arenes indicated that they existed in cone conformation in solution.     

Synthesis and properties of novel cardo aromatic poly(ether‐benzoxazole)s

Three new bis(ether‐acyl chloride) monomers, 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]cyclohexane ( 1a ), 5,5‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐4,7‐methanohexahydroindan ( 1b ), and 9,9‐bis[4‐(4‐chloroformylphenoxy)phenyl]fluorene ( 1c ), were synthesized from readily available compounds. Aromatic polybenzoxazoles bearing ether and cardo groups were obtained by the low‐temperature solution polycondensation of the bis(ether‐acyl chloride)s with three bis(aminophenol)s and the subsequent thermal cyclodehydration of the resultant poly(o‐hydroxy amide)s. The intermediate poly(o‐hydroxy amide)s exhibited inherent viscosities in the range of 0.35–0.71 dL/g. All of the poly(o‐hydroxy amide)s were amorphous and soluble in many organic polar solvents, and most of them could afford flexible and tough films by solvent casting. The poly(o‐hydroxy amide)s exhibited glass‐transition temperatures (T_g's) in the range of 141–169 °C and could be thermally converted into the corresponding polybenzoxazoles approximately in the region of 240–350 °C, as indicated by the DSC thermograms. Flexible and tough films of polybenzoxazoles could be obtained by thermal cyclodehydration of the poly(o‐hydroxy amide) films. All the polybenzoxazoles were amorphous and showed an enhanced T_g but a dramatically decreased solubility as compared with their poly(o‐hydroxy amide) precursors. They exhibited T_g's of 215–272 °C by DSC and showed insignificant weight loss before 500 °C in nitrogen or air. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4014–4021, 2001     

Synthesis and characterization of aromatic polythiazole-amides from new aromatic diamines containing phenyl-pendant thiazole units

New aromatic diamines containing phenyl-pendant thiazole units were synthesized in three steps starting from p-nitrobenzyl phenyl ketone. Novel aromatic polyamides containing phenyl-pendant thiazole units were prepared by the low-temperature solution polyconden-sation of 1,4- (or 1.3-) bis[5-(p-aminophenyl)-4-phenyl-2-thiazolyl] benzene with various aromatic dicarboxylic acid chlorides in N,N-dimethylacetamide. High molecular weight polyamides having inherent viscosities of 0.5–3.0 dL/g were obtained quantitatively. The polythiazole-amides with m-phenylene, 4,4′-oxydiphenylene, and 4,4′-sulfonyldiphenylene units were soluble in N-methyl-2-pyrrolidone, N,N-dimethylacetamide, and pyridine, and gave transparent flexible films by casting from the solutions. These organic solvent-soluble polyamides displayed prominent glass transition temperatures (T_g) between 257 and 325°C. On the other hand, the polythiazole-amides with p-phenylene and 4,4′-biphenylene units were insoluble in most organic solvents, and had no observed T_g. All the polythiazole-amides started to decompose at about 400°C with 10% weight loss being recorded at 450–525°C in air. © 1995 John Wiley & Sons, Inc.     

Syntheses and properties of new aromatic polybenzoxazoles bearing ether and phenylethylidene or 1‐phenyl‐2,2,2‐trifluoroethylidene linkages

Two new bis(ether acyl chloride)s, 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐1‐phenylethane and 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane, were prepared from readily available reagents. Aromatic polybenzoxazoles with both ether and phenylethylidene or 1‐phenyl‐2,2,2‐trifluoroethylidene linkages between phenylene units were obtained by a conventional two‐step procedure including the low‐temperature solution polycondensation of the bis(ether acyl chloride)s with three bis(o‐aminophenol)s, yielding poly(o‐hydroxyamide) precursors, and subsequent thermal cyclodehydration. The intermediate poly(o‐hydroxyamide)s exhibited inherent viscosities of 0.39–0.98 dL/g. All of the poly(o‐hydroxyamide)s were amorphous and soluble in polar organic solvents such as N,N‐dimethylacetamide, and most of them could afford flexible and tough films via solvent casting. The poly(o‐hydroxyamide)s exhibited glass‐transition temperatures (T_g's) of 129–194 °C and could be thermally converted into corresponding polybenzoxazoles in the solid state at temperatures higher than 300 °C. All the polybenzoxazoles were amorphous and showed an enhanced T_g but a dramatically decreased solubility with to respect to their poly(o‐hydroxyamide) precursors. They exhibited T_g's of 216–236 °C through differential scanning calorimetry and were stable up to 500 °C in nitrogen or air, with 10% weight‐loss temperatures being recorded between 538 and 562 °C in nitrogen or air. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 914–921, 2003     

Synthesis and characterization of novel fluorinated polyimides derived from 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethylphenyl)ethylidene]diphthalic anhydride and aromatic diamines

A novel fluorinated aromatic dianhydride, 4,4′‐[2,2,2‐trifluoro‐1‐(3‐trifluoromethyl‐phenyl)ethylidene]diphthalic anhydride (TFDA) was synthesized by coupling of 3′‐trifluoromethyl‐2,2,2‐trifluoroacetophenone with o‐xylene under the catalysis of trifluoromethanesulfonic acid, followed by oxidation of KMnO₄ and dehydration. A series of fluorinated aromatic polyimides derived from the novel fluorinated aromatic dianhydride TFDA with various aromatic diamines, such as p‐phenylenediamine (p‐PDA), 4,4′‐oxydianiline (ODA), 1,4‐bis(4‐aminophenoxy)benzene (p‐APB), 1,3‐bis(4‐amino‐phenoxy)benzene (m‐APB), 4‐(4‐aminophenoxy)‐3‐trifluoromethylphenylamine (3FODA) and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (6FAPB), were prepared by polycondensation procedure. All the fluorinated polyimides were soluble in many polar organic solvents such as NMP, DMAc, DMF, and m‐cresol, as well as some of low boiling point organic solvents such as CHCl₃, THF, and acetone. Homogeneous and stable polyimide solutions with solid content as high as 35–40 wt % could be achieved, which were prepared by strong and flexible polyimide films or coatings. The polymer films have good thermal stability with the glass transition temperature of 232–322 °C, the temperature at 5% weight loss of 500–530 °C in nitrogen, and have outstanding mechanical properties with the tensile strengths of 80.5–133.2 MPa as well as elongations at breakage of 7.1–12.6%. It was also found that the polyimide films derived from TFDA and fluorinated aromatic diamines possess low dielectric constants of 2.75–3.02, a low dissipation factor in the range of 1.27–4.50 × 10^?3, and low moisture absorptions <1.3%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4143–4152, 2004     

Studies on metathetical and thermal polymerization of 5-norbornene 2,3-dicarboximide end-capped resins Pt-II

The article deals with synthesis, characterization, and polymerization of 5-norbornene-2,3-dicarboximide end-capped resins (bisnadimides) based on 4,4′-diaminodiphenylether, 1,4/1,3-bis(4′-aminophenoxy) benzene, 2,2′-bis[4-(4′-aminophenoxy)phenyl]propane, and bis[4-(4′-aminophenoxy)phenyl]sulphone. Both exo and endo bisnadimides were prepared by reacting the aromatic diamines with exo or endo nadic anhydride in glacial acetic acid at 120°C. The exo or endo bisnadimides could be distinguished on the basis of differences observed in IR or ¹H-NMR spectra. Both thermal (in solid state) and metathetical polymerization (using WCl₆/tetramethyltin catalyst and chlorobenzene solvent) of bisnadimides was carried out. Only exo bisnadimides could be polymerized using metathesis reaction whereas thermal polymerization of both endo and exo bisnadimide could be successfully carried out at 300°C in static air atmosphere. The polymers were highly crosslinked and insoluble in common organic solvents. The polymers obtained by metathesis polymerization were light brown in color whereas those obtained by thermal polymerization were dark brown in color. Thermal stability of the thermally polymerized exo or endo bisnadimides was comparable. These polymers were stable up to 400°C and decomposed in a single step above this temperature. The char yield at 800°C depended on the structure of the polymer and was in the 39–56% range. The polymers formed by metathesis polymerization showed a 1–3% weight loss in the temperature range 226–371°C and decomposed in a single step above 440°C. The char yields were higher in these polymers (53–71%) compared to those obtained by thermal polymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2323–2331, 1997     

Synthesis and properties of germanium-containing poly(diphenylacetylenes)

1-Phenyl-2-[m-(trimethylgermyl)phenyl]acetylene (m-Me₃GeDPA) and 1-phenyl-2-[p-(trimethylgermyl)phenyl]acetylene (p-Me₃GeDPA) polymerized with TaCl₅–cocatalyst systems to provide in high yields new polymers having weight-average molecular weights over 1 × 10⁶. Poly(m-Me₃GeDPA) was a yellow solid, which completely dissolved in toluene, chloroform, etc., to form a tough film by solution casting. Poly(p-Me₃GeDPA) was also a yellow solid and partly insoluble in any solvents. The onset temperatures of weight loss for these polymers in the thermogravimetric analysis in air were as high as ca. 400°C. The oxygen permeability coefficient of poly(m-Me₃GeDPA) was 1100 barrers (25°C), which is about twice that of poly(dimethylsiloxane). © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of organosoluble ditrifluoromethylated aromatic polyimides

Two novel diamine monomers, 1,4‐bis (4‐aminophenoxy)‐2‐[(3′,5′‐ditrifluoromethyl)phenyl]benzene and 1,4‐bis [2′‐cyano‐3′(4″‐amino phenoxy)phenoxy]‐2‐[(3′,5′‐ditrifluoromethyl)phenyl] benzene, were synthesized from (3,5‐ditrifluoromethyl)phenylhydroquinone. A series of ditrifluoromethylated aromatic polyimides derived from the diamines were prepared through a typical two‐step polymerization method. These polyimides had a high thermal stability, and the temperatures at 10% weight loss were above 507 °C in nitrogen. Most of the polymers showed good solubility in anhydrated 1‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, chloroform, and tetrahydrofuran at room temperature. All the polymers formed transparent, strong, and flexible films with tensile strengths of 63.6–95.8 MPa, elongations at break of 5–10%, and Young's moduli of 2.38–2.96 GPa. The dielectric constants estimated from the average refractive indices are 2.69–2.89. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3018–3029, 2005     

Synthesis and properties of highly refractive polyimides derived from fluorene‐bridged sulfur‐containing dianhydrides and diamines

Highly refractive and transparent polyimides (PIs) based on fluorene‐bridged and sulfur‐containing monomers have been developed. An aromatic dianhydride, 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA), was polymerized with several fluorene‐containing diamines, including commercially available 9,9′‐bis(p‐aminophenyl)fluorene (APF), 9,9′‐bis[4‐(p‐aminophenoxy)phenyl]fluorene (OAPF), and newly synthesized 9,9′‐bis[4‐(p‐aminophenyl)sulfanylphenyl]fluorene (ASPF) to afford series A PIs. Meanwhile, series B PIs were obtained from a new dianhydride, 4,4′‐[(9H‐fluorene‐9‐ylidene)bis(p‐phenylsulfanyl)]diphthalic anhydride (FPSP) and two aromatic diamines, ASPF and 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] (3SDA) via a two‐step polycondensation procedure. The PIs exhibit good thermal stabilities, such as relatively high glass transition temperatures in the range of 220–270 °C and high initial thermal decomposition temperatures (T_10%) exceeding 490 °C. The 9,9′‐disubstituted fluorene moieties endow the PI films with good optical transparency. The optical transmittances of the PI films at 450 nm are all higher than 80% for the thickness of about 10 μm. Furthermore, the highly aromatic fluorene moiety and flexible thioether linkages in the molecular chains of the PIs provide them with high refractive indices of 1.6951–1.7258 and small birefringence of 0.0056–0.0070. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1510–1520, 2008     

Synthesis and polymerization of 1,3-bis-(2,3-epoxypropylphenyl)tetramethyldisiloxanes and related compounds

1,3-Bis[p-(2,3-epoxypropyl)phenyl]tetramethyldisiloxane and its meta isomer were synthesized and subsequently cured with m-phenylenediamine. Dielectric properties of the cured resin derived from the para isomer were measured between 25 and 100°C. The ambient temperature dielectric constant of the resin at 1 kc./sec. was 3.4, its dissipation factor was 0.01, and its volume resistivity was 10¹⁴ ohm-cm. at 500 v. d.c. Several allylphenylsiloxanes were also prepared by the cohydrolysis of allylphenyldimethylethoxysilane with dimethyldiethoxysilane, bis(dimethylethoxysilyl)benzene, and methyltriethoxysilane. Preliminary epoxidation studies on these latter materials were also carried out.     

Polymerization of diphenylacetylenes having very bulky silyl groups and polymer properties

Polymerization and polymer properties of 1-phenyl-2-[4-(triphenylsilyl)phenyl]acetylene (pPh₃SiDPA) and 1-phenyl-2-[4-(triisopropylsilyl)phenyl]acetylene (piPr₃SiDPA), which have very bulky silyl groups, were examined. These monomers polymerized in good yields in the presence of TaCl₅-based catalysts. The highest weight-average molecular weights of poly(pPh₃SiDPA) and poly(piPr₃SiDPA) reached about 1 × 10⁶ and 4.8 × 10⁶, respectively. The polymers were yellow to orange-colored solids which were soluble in toluene, chloroform, etc., and provided free-standing films by solution casting. The onset temperatures of weight loss of poly(pPh₃SiDPA) and poly(piPr₃SiDPA) in TGA in air were 430 and 270°C, respectively. The oxygen permeability coefficients of poly(pPh₃SiDPA) and poly(piPr₃SiDPA) at 25°C were 3.8 and 20 barrers, respectively, and relatively small. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2721–2725, 1998     

Syntheses and properties of novel fluorinated polyamides based on a bis(ether‐carboxylic acid) or a bis(ether amine) extended from bis(4‐hydroxyphenyl)phenyl‐2,2,2‐trifluoroethane

Two series of novel fluorinated aromatic polyamides were prepared from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic dicarboxylic acids with the phosphorylation polyamidation technique. These polyamides had inherent viscosities ranging from 0.51 to 1.54 dL/g that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 36,200–80,000 and 17,200–64,300, respectively. All polymers were highly soluble in aprotic polar solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some could even be dissolved in less‐polar solvents like tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 76–94 MPa and initial moduli of 1.70–2.22 GPa. Glass‐transition temperatures (T_g's) and softening temperatures of these polyamides were observed in the range of 185–268 °C by differential scanning calorimetry or thermomechanical analysis. Decomposition temperatures (T_d's) for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. Almost all the fluorinated polyamides displayed relatively higher T_g and T_d values than the corresponding nonfluorinated analogues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 420–431, 2003     

Acyl- und Alkylidenphosphane. XXIII [1]. Synthese und Struktur der [Bis(trimethylsilylsulfano)methyliden]phosphane

Acyl- and Alkylidenephosphines. XXIII. Synthesis and Structure of [Bis(trimethylsilylsulfano)methylidene]phosphines Analogous to the phenyl derivative 1a [2] tert-butyl- 1b , mesityl- 1c and methylbis-(trimethylsilyl)phosphine 1 d react with carbon disulfide to give the corresponding [bis(trimethylsilylsulfano)methylidene]phosphines 4 . Only in case of the mesitylphosphine 1 c the intermediate compounds 2 and 3 could be detected by n.m.r. spectroscopic methods; thermally unstable [bis(trimethylsilylsulfano)methylidene]methylphosphine 4 d dimerizes rapidly [1]. [Bis(trimethylsilylsulfano)methylidene]phenylphosphine 4 a crystallizes in the monoclinic centrosymmetric space group P2₁/c with following dimensions of the unit cell determined at ?95 ± 3°C: a = 1386.4(8); b = 1036.0(7); c = 1281.7(8) pm; ß = 101.23(4)°; Z = 4. An X-ray structure determination (R = 0.032) proves the constitution of this compound as already derived from its nmr spectra. Characteristic bond lengths and angles are: P?C 170; P? C(phenyl) 183; C? S 176; S? Si 219 pm; C? P?C 107; P?C? S 124 and 120; S? C? S 116 and C? S? Si 111°.     

Radical polymerization of ortho-(1,3-dioxolan-2-yl)phenyl ethyl fumarate involving intramolecular hydrogen abstraction and ring opening of cyclic acetal

The polymerization of o-(1,3-dioxolan-2-yl)phenyl ethyl fumarate (DOPEF) initiated with dimethyl 2,2′-azobisiso-butyrate (MAIB) was studied kinetically in benzene. The polymerization rate (R_p) at 60°C was given by R_p = k [MAIB]^0.76 [DOPEF]^0.71. The overall activation energy of polymerization was calculated to be 98.3 kJ/mol. The number-average molecular weight of resulting poly(DOPEF) was in the range of 1000–3100. ¹H- and ¹³C-NMR spectra of resulting polymers revealed that the radical polymerization of DOPEF proceeds in a complicated manner involving vinyl addition, intramolecular hydrogen abstraction, and further ring opening of the cyclic acetal at higher temperatures. From the copolymerization of DOPEF (M₁) and styrene (St) (M₂) at 60°C, the monomer reactivity ratios were obtained to be r₁ = 0.02 and r₂ = 0.20, the values of which are similar to those of the copolymerization of ethyl o-formylphenyl fumarate and St. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 563–572, 1998     

Synthesis and properties of novel aromatic polyamides based on “multi-ring” flexible dicarboxylic acids

The five benzene rings-containing (hereafter referred to as “five-ring”) dicarboxylic acids α,α′-bis[4-(4-carboxyphenoxy)phenyl]-1,4-diisopropylbenzene (p- III ) and α,α′-bis[4-(4-carboxyphenoxy)phenyl]-1,3-diisopropylbenzene (m- III ) were prepared by the fluoro-displacement of α,α′-bis(4-hydroxyphenyl)-1,4-diisopropylbenzene and α,α′-bis(4-hydroxyphenyl)-1,3-diisopropylbenzene with p-fluorobenzonitrile, and subsequent alkaline hydrolysis of the intermediate dinitriles. A number of high-molecular-weight polyamides based on these two “five-ring” dicarboxylic acids (p- III and m- III ) and various aromatic diamines were directly synthesized in N-methyl-2-pyrrolidone (NMP) containing lithium chloride (LiCl) or calcium chloride (CaCl₂) using triphenyl phosphite and pyridine as condensing agents. These polyamides were obtained with inherent viscosities above 0.51 and up to 0.91 dL/g. The weight-average molecular weight were in the range of 51,000–211,000. Most of these polyamides were amorphous and readily soluble in polar solvents such as NMP, N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), and dimethyl sulfoxide (DMSO), and afforded tough, flexible, and transparent films by solution-casting. The films had tensile strength of 50–83 MPa, elongation to break of 4–8%, and tensile modulus of 1.3–2.0 GPa. Most polyamides showed distinct glass transitions on the differential scanning calorimetry (DSC) curves ranging from 147 to 177°C. In nitrogen or air, all the polymers showed no significant weight loss up to 490°C, as indicated by thermogravimetric analysis (TG). © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of phenyl-pendant aromatic polythiazoles from bis-α-bromophenylacetyl compounds and dithioamides

Novel phenyl-pendant aromatic polythiazoles having inherent viscosities of 0.3–1.3 dL/g were synthesized by the solution polycondensation of bis[4-(α-bromophenylacetyl)phenyl] ether with aromatic dithioamides or dithiooxamide in dimethylformamide at 60°C. The polythiazole having m-phenylene linkage was readily soluble in chloroform and m-cresol, and transparent flexible film could be cast from the chloroform solution. Glass transition temperatures of these polythiazoles were in the range of 210–250°C. They started to decompose at about 500°C in air with 10% weight loss being recorded at around 570°C.     

3‐[4′‐(Diethylboryl)phenyl]pyridine: Exclusive Crystallization of the Cyclic Tetramer

The crystallization of 3‐[4′‐(diethylboryl)phenyl]pyridine ( 1 ), which formed a mixture of oligomers in solution with the cyclic trimer as a major component, in acetone at 0 °C afforded a cyclic tetramer that co‐crystallized with solvent molecules. Similarly, solutions of compound 1 in toluene at 10 °C and in benzene at 8 °C furnished the cyclic tetramer with the incorporation of toluene and benzene molecules, respectively, thus suggesting that the cyclic tetramer was the minor component. ¹³C CP/MAS NMR spectroscopy of precipitates of compound 1 suggested that precipitation from acetone and toluene each afforded mixtures of the cyclic trimer and the cyclic tetramer, whereas precipitation from benzene exclusively furnished the cyclic tetramer. Therefore, it appeared that crystallization readily shifted the equilibrium towards the cyclic tetramer in benzene. The thermodynamic parameters for the equilibrium between these two oligomers in [D₆]benzene, as determined from a van′t Hoff plot, were ΔH°=?8.8 kcal mol^?1 and ΔS°=?23.7 cal mol^?1 K^?1, which were coincident with previously reported calculations and observations.     

Synthesis and properties of poly[arylene ether (N-arylenebenzimidazole)]s

Poly(arylene ether)s containing N-arylenebenzimidazole groups were prepared by the aromatic nucleophilic displacement reaction of two new bis(hydroxyphenyl-N-arylenebenzimidazole)s with activated aromatic difluorides in sulfolane at 200°C in the presence of anhydrous potassium carbonate. The bis(hydroxyphenyl-N-arylenebenzimidazole)s were prepared from bis(o-aminoanilino) arylenes and phenyl-4-hydroxybenzoate. The polymers were soluble in N-methyl-2-pyrrolidinone and m-cresol and exhibited inherent viscosities from 0.37–0.86 dL/g and glass transition temperatures from 219–289°C. Thermogravimetric analyses showed 5% weight losses from 463–506°C in air and 467–522°C in nitrogen. Unoriented thin films exhibited tensile strengths, moduli, and break elongations at 23°C of 10.2–12.5 ksi, 318–365 ksi, and 4–7%, respectively, and at 177°C of 5.1–6.9 ksi, 256–296 ksi, and 1–5%, respectively. A 50 : 50 random copolymer prepared from 1,3-bis(4-fluorobenzoyl) benzene, 1,1'-(4,4'-biphenylene)-bis[2-(4-hydroxyphenyl)benzimidazole], and 5,5'-bis[2-(4-hydroxyphenyl)benzimidazole] exhibited higher moisture absorption and lower tensile properties than those predicted by a rule of mixtures relationship. The chemical, physical, and mechanical properties of these polymers are discussed. © 1993 John Wiley & Sons, Inc.?     

Effects of diamines and their fluorinated groups on the color lightness and preparation of organosoluble aromatic polyimides from 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐hexafluoropropane

To investigate the position and amount of the CF₃ group affecting the coloration of polyimides (PIs), we prepared 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]hexafluoropropane ( 2 ) with four CF₃ groups with 2‐chloro‐5‐nitrobenzotrifluoride and 2,2‐bis(4‐hydroxyphenol)hexafluoropropane. A series of soluble and light‐colored fluorinated PIs ( 5 ) were synthesized from 2 and various aromatic dianhydrides ( 3a – 3f ). 5a – 5f had inherent viscosities ranging from 0.80 to 1.19 dL/g and were soluble in amide polar solvents and even in less polar solvents. The glass‐transition temperatures of 5 were 221–265 °C, and the 10% weight‐loss temperatures were above 493 °C. Their films had cutoff wavelengths between 343 and 390 nm, b* values (a yellowness index) ranging from 5 to 41, dielectric constants of 2.68–3.01 (1 MHz), and moisture absorptions of 0.03–0.29 wt %. In a comparison of the PI series 6 – 8 based on 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, 2,2‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]propane, and 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane, we found that the CF₃ group close to the imide group was more effective in lowering the color; this means that CF₃ of 5 , 7 , and 8f was more effective than that of 6c . The color intensity of the four PI series was lowered in the following order: 5 > 7 > 6 > 8 . The PI 5f , synthesized from diamine 2 and 4,4′‐hexafluoroisopropylidenediphthalic anhydride, had six CF₃ groups in a repeated segment, so it exhibited the lightest color among the four series. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 922–938, 2003