Synthesis and characterization of soluble polyimides derived from [1,1′;4′,1″]terphenyl‐2′,5′‐diol and biphenyl‐2,5‐diol

Two series of polyimides based on laterally attached p‐terphenyl and biphenyl groups were synthesized. The solubility and thermal properties were studied using DSC, thermogravimetric analysis, and the solubility test. These polymers exhibited good thermal stability and excellent solubility. The high solubility for both polymer series was attributed to the non‐coplanarity of diamine monomers and the use of fluorinated dianhydride, whereas the slightly better solubility for polymers based on p‐terphenyl was attributed to further weakening of interchain interaction of the polymers. Both polymer series exhibited glass‐transition temperatures (T_g's) in the range of 244–272 °C. The T_g's of polymers containing laterally attached p‐terphenyls were higher than those of their counterparts containing biphenyls by 5–17 °C. This was attributed to the formation of an interdigitated structure that hinders the segmental movement of polymer chains. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2998–3007, 2001     

Preparation,characterization, and properties of poly(thioether ether ketone imide)s from isomeric bis(chlorophthalimide)s

A series of novel poly(thioether ether ketone imide)s (PTEKIs) bearing the thioether and ketone groups with high molecular weights (M_w: 87,800–150,100 g/mol) were synthesized by aromatic nucleophilic substitution reaction. The polymers were characterized by Fourier transform infrared spectra (FT‐IR), ¹H NMR, GPC, and elemental analysis. The composition of the copolymers varied systematically in order to study its relation with polymer properties. Increase in the content of 3‐substituted phthalimide moiety in the polymer backbone improves the solubility in tested solvents, and increases the glass transition temperature (T_g), whereas copolymers with high content of 3‐substituted phthalimide demonstrated to be inferior thermal stability. The PTEKI films also exhibited good optical transparency, including the cutoff wavelengths lower than 400 nm and transmittances higher than 77% at 450 nm. Copyright © 2010 John Wiley & Sons, Ltd.     

Glass transformation temperatures of polymers of olefin oxides and olefin sulfides

A number of polymers belonging to poly(olefin oxide) and poly(olefin sulfide) series have been prepared and their glass transformation temperatures determined by dilatometry and differential thermal analysis. In the poly(olefin oxide) series, the T_g remained practically unchanged as the length of the pendent alkyl group was increased from methyl to n-hexyl. However, a 20°C decrease in T_g was observed when the pendent group was changed from ethoxymethyl to n-hexoxymethyl. In the poly-(olefin sulfide) series, the T_g value decreased as the pendent alkyl group changes from methyl to ethyl. Replacement of ether oxygen in the polymer main chain by sulfide sulfur increased the T_g value. In some polymers, first-order transitions were observed, but their significance has not been assessed.     

Thermophysical properties of azomethine ether main-chain liquid crystalline polymers at pressures to 200 MPa

This article reports on an experimental investigation of the equation of state and the transition behavior of main-chain thermotropic liquid crystalline polymers over a wide temperature range, and at pressures to 200 MPa. The materials studied were a series of azomethine ether polymers. A varying number n (= 4, 7, 8, 9, 10 and 11) of methylene spacer units in the backbone provided systematic variation of the structure. Experimental techniques used included high-pressure dilatometry (PVT measurements) to 200 MPa, high-pressure differential thermal analysis, also to 200 MPa, and conventional (atmospheric-pressure) differential scanning calorimetry (DSC). The equation of state of the materials can be well represented by the Tait equation in distinct regions, separated by a glass transition, T_g(P), a first-order transition to a nematic state, T_k-n(P), and a first-order transition to an isotropic melt state T_c(P). The atmospheric pressure values of T_k-n and T_c decreased with increasing number of spacer units and showed a clear odd-even effect. T_g and T_k-n both increased with pressure. The pressure dependence of T_c could not be observed due to the onset of degradation in the same temperature region. On isobaric cooling at 3°C/min, the crystallization from the nematic state occurred a few tens of degrees below T_k-n. This supercooling was independent of pressure for some materials, while for others it increased with increasing pressure. The values of the enthalpy and entropy associated with the first-order transition into the nematic state were lower than those of typical isotropic polymers at their melting transitions. The transition enthalpy did not have any systematic variation with increasing number of spacer units. Values of the transition enthalpy calculated from the Ciapeyron equation did not always agree with the values measured by DSC. This may be due to the two-phase nature of the low-temperature state. At the transition to the isotropic state, the transition enthalpy at P = 0 decreased with n and showed an odd-even effect. © 1994 John Wiley & Sons, Inc.     

Thermoanalytical evaluation of readily available reference polymers

A commercial set of polymers has been characterized by TG-DTA, DSC, TMA, FTIR spectroscopy and X-ray diffraction analysis (XRD). Thermal and mechanical stability, as well as the polymer glass transition temperature,T _g, and melt temperature,T _m, have been documented. There is a good correlation between measuredT _g andT _m values and published data. The degree of polymer crystallinity for polyethylene has been verified by XRD. The credibility and stability of these reference polymers is based on a comparison of their thermal properties, over a wide range of temperatures from two versions of a reference set, published in 1979 (A) and 1994 (B). The thermal properties and crystallinity of these polymers have stood the test of time and are reliable, readily available and consistent.     

Synthesis and characterization of fluorinated benzoxazole polymers with high Tg and low dielectric constant

Next generation microelectronic packaging requirements are driving the need to produce increasingly lower dielectric constant materials while maintaining high thermal stability and ease of processing. Efforts have focused on the synthesis and analysis of new polymers with the goals of high thermal stability [degradation temperature (T_d) > 400 °C, low glass‐transition temperature (T_g) > 350 °C], low water uptake (<1%), solubility in selected organic solvents, dielectric constant less than 2.5, and low thermal expansion coefficient. These stringent combined goals have been largely achieved with flexible aromatic benzoxazole polymers. Intramolecular hydrogen bonding between pendant hydroxyl groups and the double‐bond nitrogen of the benzoxazole has been exploited to increase the polymer T_g, whereas the incorporation of perfluoroisopropyl units effectively decreases the dielectric constant. Out‐of‐plane impedance measurements on films of materials in this family (38–134 μm thick) have resulted in typical dielectric values of 2.1–2.5 at 1 MHz, depending on copolymer ratios and functionalizations. Results have been correlated with optical waveguide measurements of films 4‐μm thick to determine film anisotropy and the high‐frequency dielectric constant, and have been corroborated by in‐plane interdigitated electrode dielectric measurements on samples 0.75 μm thick. Candidate materials exhibited extremely low water uptake (0.2%) even after submersion in boiling water for several days. Dynamic mechanical analysis of the polymers enabled the determination of the influence of intermolecular hydrogen bonding on the T_g and loss tangent magnitude. Finally, the coefficient of thermal expansion has been examined and correlated with copolymer constitution. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1991–2003, 2000     

Semicrystalline poly(vinyl ether)s with high and phototunable glass transition temperature: application for thermally stable and reworkable adhesives

The photoinduced solid–liquid phase transition of azobenzene-based polymers is an attractive method to synthesize stimuli-responsive functional materials. As the structure–property relationships of such materials are not fully understood, a new class of polymer backbone, that is, poly(vinyl ether) (PVE), was studied for the development of azobenzene-based polymers with high thermal stability. For this purpose, a series of azobenzene-based PVEs with different monomer structures were synthesized using a Lewis acid catalyst-based cationic polymerization method. Typical PVEs are viscous polymers with low glass-transition temperatures (T_g's). The flexibility of the polymer backbone improves with the use of alkylene spacers, changing the order of alignment of the mesogenic azobenzene moieties attached to the backbone, leading to high T_g's of the azobenzene-based PVEs. One of the synthesized PVEs shows a high glass-transition temperature of 94 °C, which is 14 °C higher compared to that of the corresponding polymethacrylate. Furthermore, the PVE exhibits photoinduced solid–liquid phase transition from the semicrystalline state. This phase transition material, with its high thermal stability, has the potential for broader applications, such as for the phototuning of adhesion. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 568–577     

Synthesis and characterization of 3-aryl-2-(polystyryl)cyclopropenones via cyclopropenium ion substitution on polystyrene

Electrophilic substitution of cyclopropenium ions on aromatic polymers offers a unique opportunity to introduce polar functionality in a controlled manner to conventional, nonpolar polymers. Phenylcyclopropenone substituted polystyrene with predictable chemical composition and narrow molecular weight distribution were prepared. Size exclusion chromatography (SEC) analysis demonstrated the absence of branching or crosslinking in these functionalized polystyrenes during electrophilic substitution of the parent homopolymer. ¹³C-NMR confirmed that the degree of phenylcyclopropenone substitution was both highly efficient and predictable over a broad compositional range. The glass transition temperature (T_g) of the polymers was found to vary linearly with mole % phenylcyclopropenone substitution of the polystyrene. Thermal gravimetric analysis (TGA) indicated that thermal decarbonylation of the appended cyclopropenones occurred at approximately 180°C. Weight loss vs. temperature profiles correlated reasonably well with levels of substitution based on ¹³C-NMR analysis, confirming that decarbonylation of the calculated cyclopropenone substituents was the predominant thermal decomposition pathway. © 1995 John Wiley & Sons, Inc.     

Pressure dependence of the dielectric properties and phase transitions of polyvinylidene fluoride (PVDF) and a copolymer with trifluoroethylene

The frequency, temperature, and hydrostatic pressure dependences of the dielectric properties, molecular relaxations, and phase transitions in PVDF and a copolymer with a 30 mol% trifluoroethylene were investigated. The β-relaxation peak temperature T_β and the melting temperature T_m of both polymers, and the ferroelectric transition temperature T_c of the copolymer, are strong increasing functions of pressure. The magnitudes of the pressure derivatives of T_β, T_c, and T_m increase in the order of the “transition” temperatures, i.e., T_β(P) < T_c(P) < T_m(P). These results can be qualitatively understood in terms of the nature of the molecular motion and/or reorientation processes involved. The results on the copolymer suggest that pressure should induce a ferroelectric-paraelectric transition in PVDF below T_m, but such a transition was not observed over the limited pressure range of the present experiments. The relaxational dynamic (not static) nature of the melting process in these materials is indicated by the observed dependence of T_m on probe frequency. The frequency (or rate) and strong pressure dependences of T_m of PVDF provide a rational explanation for why it is possible to use this polymer as a piezoelectric shock-wave gauge to relatively high shock pressures and the accompanying high temperatures.     

Manipulation of Molecular Weight Distribution Shape as a New Strategy to Control Processing Parameters

Molecular weight and dispersity (Ð ) influence physical and rheological properties of polymers, which are of significant importance in polymer processing technologies. However, these parameters provide only partial information about the precise composition of polymers, which is reflected by the shape and symmetry of molecular weight distribution (MWD). In this work, the effect of MWD symmetry on thermal and rheological properties of polymers with identical molecular weights and Ð is demonstrated. Remarkably, when the MWD is skewed to higher molecular weight, a higher glass transition temperature (T _g), increased stiffness, increased thermal stability, and higher apparent viscosities are observed. These observed differences are attributed to the chain length composition of the polymers, easily controlled by the synthetic strategy. This work demonstrates a versatile approach to engineer the properties of polymers using controlled synthesis to skew the shape of MWD.     

Mesomorphic and luminescent properties of side chain nematic liquid-crystalline polymers containing Ir(III)

Iridium-containing liquid-crystalline polymers were obtained by graft copolymerisation using poly(methylhydrogeno)siloxane, 1-methyl-4-(4-(4-vinylcyclohexyl)cyclohexyl)benzene (M₁) and an iridium complexes monomer (Ir-M₂). The series of polymers contained different molecular fractions of Ir-M₂ from 0% to 1.2%. All of these polymers showed mesomorphic behaviours. The introduction of small amount of iridium ions endowed liquid-crystalline polymers with luminescent properties. The chemical structures were characterised by IR and ¹H NMR. The mesomorphic properties and phase behaviour were investigated by differential scanning calorimetry, thermal gravimetric analysis, polarising optical microscopy and X-ray diffraction. With an increase of iridium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) decreased. All polymers showed typical nematic marble textures, which was confirmed by X-ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of iridium complexes units did not change the liquid-crystalline state of polymer systems. With Ir³⁺ ion contents ranging between 0.6 and 2.4 mol%, luminescent intensity of polymers gradually increased.     

Solid‐state thermal stability and degradation of a family of poly(N‐isopropylacrylamide‐co‐hydroxymethylacrylamide) copolymers

There is widespread interest in responsive polymers that show cloud point behavior, but little attention is paid to their solid state thermal properties. To manufacture products based on such polymers, it may be necessary to subject them to high temperatures; hence, it is important to investigate their thermal behavior. In this study, we characterized a family of poly(N‐isopropylacrylamide‐co‐hydroxymethylacrylamide) copolymers. Although poly(N‐isopropylacrylamide) shows very high thermal stability (up to 360 °C), introduction of hydroxy side chains leads to a significant reduction in stability and new degradation processes become apparent. Thermogravimetric analysis and fourier transform infrared spectroscopy (FT‐IR) indicate that the first degradation process involves a chemical dehydration step (110–240 °C), supported by the nonreversing heat flow response in modulated temperature differential scanning calorimetry. Water loss scales with the fraction of hydroxy monomer in the copolymer. Glass transition temperatures (T_g) are higher than the temperatures causing dehydration; hence, these values relate to newly‐formed copolymer structures produced by controlled heating under nitrogen. Fourier transform‐Raman (FT‐Raman) spectra suggest that this transition involves imine formation. The T_g increases as the fraction of hydroxy groups in the original copolymer increases. Further heating leads to degradation and mass loss, and more complex changes in the FT‐IR spectra, consistent with formation of unsaturated species. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Wholly aromatic polyamide-hydrazides. IV. Structure–property relationships for polymers containing p-phenylene and m-phenylene units

A series of wholly aromatic polyamide-hydrazides was investigated in order to acquire clear understanding of the influence exerted by controlled structural variations in these polymers upon some of important properties, such as chain flexibility, membrane permselectivity, and thermal as well as thermo-oxidative stability. For that reason, the content of para and meta phenylene units was varied within this series so that the changes in the latter were 12.5 mol % from polymer to polymer, starting from an overall content of 0–50 mol %. The polymers were prepared by a low-temperature solution polycondensation reactin of p-aminobenzhydrazide (ABH) and terephthaloyl chloride (TCI), isophthaloyl chloride (ICI), and their appropriate combinations in N,N-dimethylacetamide (DMA) as solvent and all of these preparations were monitored viscometrically in order to prepare the products with as similar as possible average molecular weights. Polymer structures were characterized by elemental analysis, infrared spectrometry, and ¹³C NMR spectroscopy, while their molecular weights were determined by light scattering and dilute-solution viscometry. Polymer properties were evaluated by solution viscometry, reverse osmosis tests, and thermal gravimetric analysis. The results obtained during the preparation of these materials, their subsequent structural characterization, and their property evaluations are discussed. They clearly indicate that substitution of m-phenylene units for p-phenylene ones within this polymer series led to an increase in polymer chain flexibility (from what is usually referred to as semiflexible or semirigid to typically flexible macromolecules), disrupted selectivity of the asymmetric thin membranes under reverse osmosis conditions and decreased stability at elevated temperatures in inert as well as in oxidative atmospheres.     

Controlled synthesis and evaluation of cyanate ester/epoxy copolymer system for high temperature molding compounds

Epoxy molding compounds (EMCs) have become an integral component for high power electronics to work under harsh environment nowadays. For high temperature operation, polymer networks with high glass transition temperature (T_g) are required to ensure device stability. In this work, high T_g polymers were designed via controlled incorporation of in situ formed and thermally stable triazine structures into epoxy matrix. Reactions involved in the copolymer system of cyanate ester and epoxy (CE/EP) were investigated. Increasing ratio of cyanate ester dramatically promoted T_g of the copolymer up to 275 °C with improved heat resistance. High temperature aging and moisture absorption tests revealed that hydrolysis of polycyanurate network and rearrangement of cyanurate occurred during aging, especially for copolymers with higher than 75% of cyanate ester. Based on thermal properties and aging performance, the composition of CE/EP system was optimized. The formulated bisphenol A cyanate ester and biphenyl epoxy copolymer system has great potential to be applied as high temperature encapsulation materials in electronic packaging. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1337–1345     

Aqueous solution behavior of thermosensitive (N-isopropylacrylamide-acrylic acid-ethyl methacrylate) terpolymers

A series of N-isopropylacrylamide (NIPAM)-acrylic acid–ethyl methacrylate terpolymers with varied monomer compositions was prepared by radical polymerization. The solution behavior of these polymers was studied in dilute aqueous solution using spectrophotometry, fluorescence spectroscopy and high-sensitivity differential scanning calorimetry. The results obtained revealed that the lower critical solution temperatures depend strongly on the copolymer composition, solution pH and ionic strength. At a high pH, the ionization of acrylic acid (AA) units leads to an increase in solution cloud points (T_c). Solutions of polymers containing 10% or less of AA display a constant T_c for pH above 5.5, with 15% there is a continuous increase in T_c with pH and, for higher AA contents, no clouding was observed within the studied temperature range. Fluorescence probe studies were conducted by following the I ₁/I ₃ ratio of pyrene vibronic bands and the emission of anilinonaphtalene sulfonic acid, sodium salt (ANS), both approaches revealing the existence of hydrophobic domains for polymers with higher ethyl methacrylate content at temperatures lower than T_c, suggesting some extent of aggregation and/or a coil-to-globule transition. Scanning calorimetry measurements showed an endothermic transition at temperatures agreeing with the previously detected cloud points. Moreover, the transition curves became broader and with a smaller transition enthalpy, as both the AA content and the solution pH were increased. These broader transitions were interpreted to be the result of a wider molecular distribution upon polymer ionization, hence, displaying varied solution properties. The decrease in transition enthalpy was rationalized as a consequence of reminiscent hydration of NIPAM units, even after phase separation, owing to the presence of electric charges along the polymer chain.     

Spectrophotometric determination of thermal transition of polymeric systems using photochromic probes

Mercury-dithizone complex both free and bonded to a polymeric system has been synthesized and used to measure the thermal transition of polystyrene, poly(vinyl acetate), and some other polymers. The thermal relaxation rate of the activated complex in dark has been found to be dependent on the free volume of a polymer matrix. The rate goes through a maximum above T_g of a polymer. A very sensitive method, based on thermal recovery of activated photochromic probe chromophore has been devised to measure the thermal transition of both single and multicomponent polymer matrices. © 1995 John Wiley & Sons, Inc.     

The linear rheological responses of wedge‐type polymers

The linear rheological responses of a series of specially designed wedge‐type polymers synthesized by the polymerization of large molecular weight monomers have been measured. These wedge polymers contained large side groups which contained three flexible branch chains per polymer chain unit. The master curves for these polymers were obtained by time temperature superposition of dynamic data at different temperatures from the terminal flow regime to well below the glass transition temperature, T_g. While these polymers maintained a behavior similar to that of linear polymers, the influence of the large side group structure lead to low entanglement densities and extremely low rubbery plateau modulus values, being near to 13 kPa. The viscosity molecular weight dependence was also somewhat higher than that normally observed for linear polymers, tending toward a power law near to 4.2 rather than the typical 3.4 found in entangled linear chains. The glassy modulus of these branched polymers is also found to be extremely low, being less than 100 MPa at T_g ?60 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 899–906     

Effect of polymer architecture on self‐diffusion of LC polymers

Two LC side‐group poly(methacrylates) were synthesized, and their melt dynamics were compared with each other and a third, main‐chain side‐group combined LC polymer. A new route was developed for the synthesis of the poly(methacrylate) polymers which readily converts relatively inexpensive perdeuteromethyl methacrylate to other methacrylate monomers. Self‐diffusion data was obtained through the use of forward recoil spectrometry, while modulus and viscosity data were measured using rotational rheometers in oscillatory shear. Diffusion coefficients and complex viscosity were compared to previous experiments on liquid crystal polymers of similar architecture to determine the effect of side‐group interdigitation and chain packing on center of mass movement. The decyl terminated LC side‐group polymer possessed an interdigitated smectic phase and a sharp discontinuity in the self‐diffusion behavior at the clearing transition. In contrast, the self‐diffusion behavior of the methyl terminated LC side‐group polymer, which possessed head‐to‐head side‐group packing, was seemingly unaffected by the smectic–nematic and nematic–isotropic phase transitions. The self‐diffusion coefficients of both polymers were relatively insensitive to the apparent glass transition. The presence of moderately fast sub‐T_g chain motion was supported by rheological measurements that provided further evidence of considerable molecular motion below T_g. The complex phase behavior of the combined main‐chain side‐group polymer heavily influenced both the self‐diffusion and rheological behavior. Differences between the self‐diffusion and viscosity data of the main‐chain side‐group polymer could be interpreted in terms of the defect structure. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 405–414, 1999     

Transition of polymers from rubbery elastic state to fluid state

On increasing the temperature of a polymer, the transition of the polymer from a rubbery elastic state to a fluid state could occur. The transition temperature is termed the fluid temperature of the polymer, T _f, which has a direct relationship with the polymer molecular weight. As one of polymer parameters, T _f is as important as the glass transition temperature of a polymer, T _g. Moreover, special attention to T _f should be paid for polymer processing. In research on the transition of a polymer from a rubbery elastic state to a fluid state, the concept of T _f would be more reasonable and more effective than the concept of T _l,l because it is neglected in the concept of T _l,l in that the molecular weight of a polymer may affect the transition of the polymer. In this paper the discussion on the fluid temperature involves the characters of polymers, such as the deformation—temperature curve, the temperature range of the rubbery state and the shear viscosity of polymer melt. From the viewpoint of the cohesional state of polymers, the transition of a polymer from a rubbery elastic state to a fluid state responds to destruction and construction of the cohesional entanglement network in the polymer. The relaxing network of polymer melt would be worthy to be considered as an object of study. __________ Translated from Huaxue Tongbao (Chemistry), 2008,71(3) (in Chinese)     

Comparative study of the phase behavior of liquid-crystalline components in closely related blends and copolyesters

Phase behavior of blends of a liquid-crystalline (LC) polymer with a non-LC polymer and of a series of copolymers containing mesogenic and nonmesogenic units was studied by thermal, optical, and dynamic mechanical methods. The polymers composing the blends and the copolymers had the same constituent monomers. The blends exhibited phase separation over the whole range of compositions studied as observed by DSC and dynamic mechanical analysis. Two glass transition temperatures (T_g) corresponding to the two components and independence of melting (T_m) and isotropization temperatures (T_i) to changes in composition were observed for the blends. The copolymers did not show phase separation over most of the composition range studied. Only one T_g corresponding to that of the major component could be detected for the copolymers, and the T_g was found to increase with an increase in the amount of nonmesogenic monomer in the copolymers. The difference in phase behavior was explained on the basis of the chemical environment of the constituent units in the blends and in copolymers. Phase inversion in the blends was observed by microscopy when the blends contained 60 mol% or more of the non-LC polymer.