A pyrrole-containing surfactant as a tecton for nanocomposite SiO2 films

A surfactant featuring a polymerizable pyrrole head group (dodecyl-dimethyl-(2-pyrrol-1-yl-ethyl)-ammonium bromide, DDPABr) was synthesized. The thermotropic behavior of the surfactant was investigated by differential scanning calorimetry (DSC) and X-ray scattering techniques, with small-angle X-ray scattering (SAXS) analysis revealing a highly ordered lamellar bilayer structure. After full characterization, DDPABr was used in the preparation of mesostructured SiO2 nanocomposite thin films via evaporation-induced self-assembly (EISA). Resulting thin SiO2-DDPABr films were studied by 1D and 2D small-angle X-ray scattering (SAXS) techniques, indicating a lamellar nanocomposite structure. Suitable theoretical SAXS models were applied to fit the experimental 1D SAXS data. The surfactant could be chemically polymerized within the lamellar domains.     

On the deformation mechanisms of oriented PET and PP films under load

Uniaxially orienred semicrystalline poly(ethylene terephthalate) (PET) and poly(propylene) (PP) films were loaded parallel to draw direction at various temperatures. Changes in the submicroscopical structure of the films under load were examined by small and wide-angle x-ray scattering (SAXS; WAXS) and birefringence measurements. WAXS measurements reveal a decrease of the initial high orientation of the chains in the crystallites during deformation. Simultaneously, an increase of the birefringence was detected, indicating an orientation of chains in the amorphous regions. The alteration of the long period reflections in the SAXS patterns give strong evidence that lamellar stacks with different orientation angles according to load direction are present. Depending on the orientation of stacks, the contribution of lamellar separation to sample deformation alters, giving rise to different amounts of density changes in the stacks. Absolute intensity measurements of SAXS using a Kratky apparatus reveal that lamellar separation occurs preferentially below or in the range of the glass-transition temperature at small strain. With increasing strain and temperatures above the glass-transition slip deformation mechanisms become more important. The formation of microvoids was observed at strain near to elongation at break below or in the range of glass-transition temperature.     

Small-angle neutron and x-ray scattering study of swollen nylon-6

Results of swelling and small-angle scattering experiments on samples of nylon-6 swollen with heavy water are discussed on the basis of the lamellar and switchboard models. The small-angle neutron scattering (SANS) intensity is very sensitive to the distribution of water in swollen samples, while the small-angle x-ray scattering (SAXS) data characterize the dry samples. The observed values of the mean-square fluctuation of scattering-density can be explained by a model with assumed inhomogeneous swelling of the amorphous phase.     

Structural changes on hot-rolling of polyethylene. I. Crystallite orientation and lamellar deformation

The crystallite orientation and lamellar deformation produced by hot-rolling in polyethylene have been investigated. In the lightly rolled stage, the [110]^* axis of polyethylene crystals orientates in the plane perpendicular to the rolling direction and the c axis becomes aligned with the rolling direction. In the heavily rolled stage the a, b, and c axes coincide with the macroscopic directions in the sample. These orientational changes are interpreted in terms of a slip mechanism. Small-angle x-ray scattering (SAXS) investigations of hot-rolled polyethylene show the following. (1) There are two kinds of lamellar structures; one in which inclined lamellae give a four-point diagram in the SAXS photograph and another in which lamellar normals are oriented around the rolling direction even at the lightly rolled stage. The latter structure is attributed to the mechanism of unfolding and recrystallization. (2) The chain-fold length in the original structure remains unchanged in the lamellae up to a roll ratio of four although the apparent long period decreases. This is explained by inclination of polymer chains in the lamellae. Further rolling aligns the polymer chains with the rolling direction and the fold length decreases.     

Dopant-Mediated Interactions in a Lecithin Lamellar Phase

Interactions induced by dopants in a lamellar phase constructed from the lecithin and water are analyzed by the small angle x-ray scattering (SAXS) technique. From SAXS patterns, scattering peak or curve shape changes disclose information on phase structure as well as the interactions between dopant and host matrices. At a certain concentration, two amphiphilic tri-block copolymers (Pluronic P123 and F127) as dopants squeeze themselves into the lecithin bilayers with PPO hydrophobic blocks and produce various effects on the lamellar phase depending on the length of PEO hydrophilic groups. Coexistence of two different lamellar phases is observed in P123-doped systems.     

利用小角/广角X射线散射联用及一维相关函数分析研究聚(ε-己内酯)片晶的形态

用小角/广角X射线散射(SAXS/WAXS)联用的实验方法考察了等温结晶温度(Tc)和等温时间对聚(ε-己内酯)(PCL)片晶形态的影响.根据WAXS数据计算了PCL的重量结晶度,进而求得其体积结晶度Vc(WAXS).在不同Tc下结晶的PCL样品的Vc(WAXS)均略高于50%.对SAXS谱线做一维相关函数(1DCF)分析,得到了PCL的片晶长周期(LP)和无定形层厚度(La).通过比较WAXS及SAXS的数据分析结果,认为PCL晶体需用"三相模型"予以描述,其过渡层厚度(E)约为LP的15%～18%,对片晶形态具有重要影响.随着Tc升高,PCL晶体的Lc、La及E均逐渐增大,但Lc的变化率最大,这使得结晶度上升.在50℃等温结晶不同时间,发现Lc随延长时间显著增加,而La及E则不断减小.等温10天后,PCL晶体的SAXS谱线上可观察到5级散射,表明片晶相当完善.     

Morphological and crystalline studies of isotactic polypropylene plastically deformed and evaluated by small-angle X-ray scattering, scanning electron microscopy and X-ray diffraction

Morphological and structural properties of isotactic polypropylene (i-PP) submitted to uniaxial plane strain deformation at ambient temperature with compression pressures of 3, 10 and 20 MPa, were investigated using wide angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Two kinds of samples were studied, namely: sample A: Mw = 117,400 g/mol Mn = 17,300, Mw/Mn = 6.8 and sample B: Mw = 271,000 g/mol Mn = 43,700 Mw/Mn = 6.2, both with isotactic content = 95%. Crystalline α- and β-phases are clearly identified by WAXD. The lamellar long period, as well as, the crystalline and amorphous lamellar thickness for the non-deformed samples measured by SAXS indicates the presence of a more symmetric spherulitic structure for sample A, while the sample B displays anisotropic scattering. The WAXD study of the apparent relative crystallinity and the orientation of crystallites, revealed that plastic deformation of i-PP by plane-strain compression, leads to preferred orientation of main axis of crystallites at relatively early stage of the deformation process induced a monocrystal texture and an excellent molecular alignment along the FD, in both samples. The SEM evaluation shows that a gradual change occurs in the spherulitic structure and seems to transform gradually and disappear almost for the 37% deformations. The sample with highest deformation shows thin shear bands oriented along the FD-view which originate an appearance of a layered structure. Concomitantly the crystalline lamellae were detected by TEM technique.     

Structural and morphological studies on the deformation behavior of polypropylene/multi‐walled carbon nanotubes nanocomposites prepared through ultrasound‐assisted melt extrusion process

Structural and morphological behavior under stress–strain of polypropylene/multi‐walled carbon nanotubes (PP/MWCNTs) nanocomposites prepared through ultrasound‐assisted melt extrusion process was studied by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, small angle X‐ray scattering (SAXS), and wide angle X‐ray scattering (WAXS). A high ductile behavior was observed in the PP/MWCNT nanocomposites with low concentration of MWCNTs. This was related to an energy‐dissipating mechanism, achieved by the formation of an ordered PP‐CNTs interphase zone and crystal oriented structure in the undeformed samples. Different strain‐induced‐phase transformations were observed by ex situ SAXS/WAXS, characterizing the different stages of structure development during the deformation of PP and PP/MWCNTs nanocomposites. The high concentration of CNTs reduced the strain behavior of PP due to the agglomeration of nanoparticles. A structural pathway relating the deformation‐induced phase transitions and the dissipation energy mechanism in the PP/MWCNTs nanocomposites at low concentration of nanoparticles was proposed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 475–491     

Influence of water in the lamellar rearrangement of internal wool lipids

Small angle X-ray scattering (SAXS) was applied to a new lipid model arrangement, which was achieved by concentrating or diluting internal wool lipid liposome suspensions in varying water concentrations. The influence of the water content in the lamellar structure of the internal wool lipids is compared with the lamellar structure of phosphatidylcholine bilayers present in the membranes of the living cells. The high increase in the lamellar distances with the water content indicates that large amounts of water can be retained in the lipid wool membrane in contrast to the case of phosphatidylcholine liposomes. A transition temperature between 40 and 50 degrees C tends to eliminate the ordered lamellar structure when more than 60% of water is present in the bilayer structure. This could account for the increase in the permeability of the wool fibres when these are soaked in water at temperatures exceeding 40 degrees C.     

Salt‐induced microphase separation of amorphous dendritic poly(ethylene oxide)‐block‐linear polystyrene copolymers

We prepared two block copolymers 1 and 2 consisting of a third‐generation dendron with poly(ethylene oxide) (PEO) peripheries and a linear polystyrene (PS) coil. The PS molecular weights were 2000 g/mol and 8000 g/mol for 1 and 2 , respectively. The differential scanning calorimetry (DSC) data indicated that neither of the block copolymers showed glass transition, implying that there was no microphase separation between the PEO and PS blocks. However, upon doping the block copolymers with lithium triflate (lithium concentration per ethylene oxide unit = 0.2), two distinct glass transitions were seen, corresponding to the salt‐doped PEO and PS blocks, respectively. The morphological analysis using small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM) demonstrated that a hexagonal columnar morphology was induced in salt‐doped sample 1‐Li⁺ , whereas the other sample ( 2‐Li⁺ ) with a longer PS coil revealed a lamellar structure. In particular, in the SAXS data of 2‐Li⁺ , an abrupt reduction in the lamellar thickness was observed near the PS glass transition temperature (T_g), in contrast to the SAXS data for 1‐Li⁺ . This reduction implies that there is a lateral expansion of the molecular section in the lamellar structure, which can be interpreted by the conformational energy stabilization of the long PS coil above T_g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2372–2376, 2010     

The microstructure of poly(vinyl chloride) as revealed by x-ray and light scattering

Small-angle x-ray scattering (SAXS) and wide-angle x-ray scattering (WAXS) as well as small-angle light-scattering (SALS) techniques have been applied to investigate the microstructure of a number of commercial poly(vinyl chloride) (PVC) samples. From the wide-angle x-ray scattering, crystallinity and crystal size parameters have been determined. The crystallinity of the samples investigated range from 5% to 10%. Superstructure parameters such as crystallite thickness, distribution functions of crystallite and amorphous thicknesses, and size of ordered regions have been obtained by an analysis of the SAXS curves using the cluster model. The crystallinity agrees well with the WAXS crystallinities indicating that most of the crystals are lamellar shaped, though some rodlike entities are present in the sample as is shown by the small-angle light scattering. From the SAXS analysis, the microstructure is described as clusters of lamella stacks which are identical with the subprimary particles. Their size is determined to be 220–240 Å. Emulsion type PVC also contains lamellar-shaped crystals. The superstructure, however, of this type of PVC is different from that of mass or suspension-polymerized material. The SAXS curve does not reveal any correlation between the crystals.     

Small-angle scattering studies of nafion membranes

The physical structure of Nafion membranes has been investigated by small-angle neutron scattering (SANS) and small-angle x-ray scattering (SAXS). Samples in the acid form may exhibit two scattering peaks. The first, observed by SANS at an angle corresponding to a Bragg spacing of 180 Å, is shown to arise from structures in crystalline regions. A second peak at larger scattering angles is shown to arise from ion-containing regions which may be swollen with water. Salt-form samples made by soaking the acid form in an aqueous salt solution can also exhibit the same two scattering signals. But in amorphous salt-form samples produced by quenching from the melt the first peak is absent. This permits a more accurate study of the second peak by SAXS, which shows that the second scattering component is present as a maximum over a wide range of water contents but is absent in a sample dried at 200°C. The position of the peak shifts to lower scattering angles (or larger spacings) at higher water contents. Possible structural models that might give rise to the maximum are discussed. A calculation of the SAX invariant is made and results are consistent with a phase separation of a large fraction of the water.     

Comparative study on the lamellar structure of polyethylene foams

A comparative study on the lamellar morphology of a collection of polyethylene foam (LDPE) has been performed in order to obtain a better understanding of the morphology of the crystalline phase of these materials. The lamellar structure was measured by small-angle X-ray scattering (SAXS), differential scanning calorimetric (DSC) and Raman spectroscopy. The results have shown that the lamellar structure of the foams is different to that of a LDPE solid sheet. Moreover, the different sensitivity of the three experimental techniques to the lamellar structure has also been analyzed.     

Optical and SAXS characterization of poly(phenylene sulfide) (PPS) oligomers

Previously reported oligomeric PPSs prepared via the melt reaction of sulfur with excess p-diiodobenzene have been examined by optical microscopy and small-angle x-ray scattering (SAXS) techniques. A transition was seen from lamellar crystals for longer chains in the PPS samples of this work to a different type, which probably are extended chain crystals, occurring at about 20 DP. Spherulitic growth was observed optically for 38.8 DP and above. SAXS data established 31.8 DP as the point where a long period peak was first observed. The lamellar thickness of these bulk crystallized samples was established as about 50 Å which corresponds to a DP of 10. Maximum intensity of the SAXS peak increased with oligomer DP indicating increasing crystal perfection. Because of the random nature of the crystallization process, in PPS the average oligomer chain must be longer than three times this lamellar thickness to allow for folding and a spherulitic growth habit. © 1994 John Wiley & Sons, Inc.     

Structure of some ethylene–phosphonic acid copolymers

An x-ray study has been made of the structure of a series of ethylene–phosphonic acid copolymers and the parent low-density polyethylene from which they were derived. The phosphonic acid contents (groups per 100 carbon atoms) of the copolymers were: A, 0.8; B, 1.8; C, 2.8; and D, 8.0. Small-angle x-ray scattering (SAXS) results show that the phosphonic acid substituents do not incorporate into the crystal lattice to any appreciable extent, that the substituents have the effect of decreasing the average thickness of the crystal lamellae and increasing the breadth of the size distribution of thicknesses, and that a two-phase model does not adequately account for the observed SAXS invariant. Wide-angle x-ray scattering (WAXS) results show that specimens, A, B, and C are partially crystalline with the polyethylene crystal structure and that D is amorphous. The observed broadenings of the 110 and 200 crystal reflections in the copolymers indicate that the substituents decrease the lateral dimensions of the crystalline lamellae and/or increase the deformation of the lattice due to external strain. Specimen D, completely amorphous according to the WAXS criterion, exhibits the largest value of the SAXS invariant of all the copolymers studied and must thus possess a multiphase structure consisting of small ordered regions and a disordered phase. The results of the study show the structure of the copolymers to be consistent with the fringe-micelle model but do not rule out the folded-chain model, although a regular fold surface is unlikely.     

Small‐angle X‐ray scattering and polymer melting: A model study

Small‐angle X‐ray scattering (SAXS) gives information on lamellar stacks in semicrystalline polymers. SAXS experiments have been used to follow the melting transition that occurs over a temperature range of 10 °C or more. One common feature is the increase in the average period by 50–100% during the melting process, a change that is often attributed to sequential melting of crystals in the lamellar stack. A quantitative treatment shows that the scattering experiment indicates only the original period, not the average period that increases throughout sequential melting. With this model, I discuss the relation between structural parameters of the melting structure and quantities derived from the SAXS intensity, the correlation function, and the interface distribution function. Uncertainties persist in our understanding of polymer melting. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2454–2460, 2001     

Integrated mechanism for the morphological structure development in HDPE melt‐blown and machine‐direction‐oriented films

The morphologies of a series of blown films and machine‐direction‐oriented (MDO) films, all produced from high density polyethylene, were characterized. In the blown film process, the crystalline morphology develops while the melt is under extensional stress. In the MDO process, drawing takes place in the solid state and deforms the crystalline morphology of the starting film. The films were characterized by wide‐angle X‐ray scattering (WAXS), small‐angle X‐ray scattering (SAXS) and atomic force microscopy to determine the lamellar morphology. The effect of the type of deformation on the lamellar morphology was studied and relationships were developed between the lamellar and polymer chain morphology using SAXS and WAXS. Blown and MDO films were found to have very different morphologies. However, an integrated mechanism was developed linking the sequential events in the deformation and morphology development in blown and MDO films. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1834–1844, 2007     

Stretching temperature and direction dependency of uniaxial deformation mechanism in overstretched polyethylene

In order to elucidate microscopic deformation behavior at different locations in isotropic semicrystalline polymers, the structural evolution of a preoriented high‐density polyethylene sample during tensile deformation at different temperatures and along different directions with respect to the preorientation was investigated by means of combined in situ synchrotron small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques. For samples stretched along preorientation, two situations were found: (1) at 30 °C, the sample broke after a moderate deformation, which is accomplished by the slippage of the microfibrils; (2) at 80 and 100 °C, fragmentation of original lamellae followed by recrystallization process was observed resulting in new lamellar crystals of different thickness depending on stretching temperature. For samples stretched perpendicular or 45° with respect to the preorientation, the samples always end up with a new oriented lamellar structure with the normal along the stretching direction via a stress‐induced fragmentation and recrystallization route. The thickness of the final achieved lamellae depends only on stretching temperature in this case. Compared to samples stretched along the preorientation direction, samples stretched perpendicular and 45° with respect to the preorientation direction showed at least several times of maxima achievable stress before macroscopic failure possibly due to the favorable occurrence and development of microdefects in those lamellar stacks with their normal parallel to the stretching direction. This result might have significant consequence in designing optimal procedure to produce high performance polyethylene products from solid state. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 716–726     

Composition fluctuation and domain spacing of low molar weight PEO–PPO–PEO triblock copolymers in the melt, during crystallization and in the solid state

We have studied a series of PEO–PPO–PEO triblock copolymers (Pluronics) in their melt and solid state mainly using static and time-resolved small-angle X-ray scattering (SAXS). In the melt state, composition fluctuations were observed. Their temperature variation was in accordance with mean-field theory. A crossover from the mean-field regime to the fluctuation regime was observed for samples with high molar mass. To check the overall conformation of molecules in the disordered state, composition fluctuations during crystallization were investigated by time-resolved SAXS. Detailed analysis on the time dependent intensity and peak position indicate that molecules remaining in the disordered state adopt a stretched overall conformation. In the solid state, crystallization of PEO blocks induced phase separation, resulting in an alternating crystalline/amorphous lamellar structure. Samples with short PEO block formed a simple lamellar structure with extended-chain conformation. The domain spacing increased with crystallization temperature due to the swelling of the amorphous domain by uncrystallized molecules. Samples with long PEO block formed a mixed lamellar structure. Structures with once-folded and extended PEO block coexisted in a large temperature range and their relative fraction changed with crystallization temperature. This mixed structure was reduced to a simple lamellar structure with once-folded crystalline structure at low crystallization temperatures.     

Crystallization and chain conformation of semicrystalline and amorphous polymer blends studied by wide‐angle and small‐angle scattering

We examine the crystallization and chain conformation behavior of semicrystalline poly(ethylene oxide) (PEO) and amorphous poly(vinyl acetate) (PVAc) mixtures with wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and small‐angle neutron scattering (SANS) experiments. For blends with PEO weight fractions (wt_PEO) greater than or equal to 0.3, below the melting point of PEO, the WAXD patterns reveal that crystalline PEO belongs to the monoclinic system. The unit‐cell parameters are independent of wt_PEO. However, the bulk crystallinity determined from WAXD decreases as wt_PEO decreases. The scattered intensities from SAXS experiments show that the systems form an ordered crystalline/amorphous lamellar structure. In a combination of WAXD and SAXS analysis, the related morphological parameters are assigned correctly. With the addition of amorphous PVAc, both the average amorphous layer thickness and long spacing increase, whereas the average crystalline layer thickness decreases. We find that a two‐phase analysis of the correlation function from SAXS, in which the scattering invariant is linearly proportional to the volume fraction of lamellar stacks, describes quantitatively the crystallization behavior of PEO in the presence of PVAc. When wt_PEO is close to 1, the samples are fully spaced‐filled with lamellar stacks. As wt_PEO decreases from 1.0 to 0.3, more PVAc chains are excluded from the interlamellar region into the interfibrillar region. The fraction outside the lamellar stacks, which is completely occupied with PVAc chains, increases from 0 to 58%. Because the radius of gyration of PVAc with a random‐coil configuration determined from SANS is smaller than the average amorphous layer thickness from SAXS, we believe that the amorphous PVAc chains still persist with a random‐coil configuration even when the blends form an ordered structure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2705–2715, 2001