Mass spectral and pyrolysis/gas-chromatographic studies of the monomer and polymer of bis(p-toluenesulfonate) of 2,4-hexadiyne-1,6-diol

The thermal degradation of the monomer and polymer of bis(p-toluenesulfonate) of 2,4-hexadiyne-1,6-diol has been investigated. Decomposition during the latter stages of solid-state thermal polymerization at 80°C and of 100% polymer at 112°C was observed by mass spectrometry and the decomposition fragments identified. Mechanisms for this low-temperature degradation are suggested. Pyrolysis of the monomer and polymer between 400 and 1000°C was studied by gas chromatography and mass spectrometry. The principal pyrolysis products are triacetylene and p-toluenesulfonic acid. The fragmentation routes leading to and derived from these products are discussed.     

First sonochemical,simple and solvent-free synthesis of chiral tert-butanesulfinimines using silica supported p-toluenesulfonic acid

A solvent-free, versatile procedure has been developed for the effective synthesis of tert-butanesulfinylimines of a variety of aldehydes using chiral tert-butanesulfinamides under green, sonochemical conditions. This method utilizes silica supported p-toluenesulfonic acid (pTSA·SiO₂) as an efficient, safer and inexpensive catalyst under aerobic conditions. The practicable simplicity, easy preparation of the catalyst from readily available substances, high substrate scope, excellent yields of products in short reaction times and environmentally benign (solvent-free sonochemical) conditions are the exceptional assets of this finding.     

Catalysis Studies of Macroreticular Polystyrene Cation‐exchange Resin with Terminal Perfluoroalkanesulfonic Acids

Macroreticular p‐(ω‐sulfonic‐perfluoroalkylated) polystyrene (FPS) resin with the advantages of both sulfonic polystyrene (such as macroreticular Amberlyst‐15) and perfluoroalkanesulfonic resin (such as superacidic Nafion NR50) has exhibited excellent catalytic selectivity and activity in cyclization of pseudoionone and condensation of indole. In this paper, FPS was characterized by XPS, nitrogen sorption technique, FESEM and Hammett indicator method, and employed as the solid acid catalyst in the esterification, acylation and alkylation reactions. The FPS resin showed better activity than commercial solid acid catalysts (Amberlyst‐15 and Nafion NR50) owing to its high surface area and strong acidity close to superacidity.     

New catalytic system for the synthesis of imidazo[1,2-a]pyridines by the Ugi reaction

A combination of N-hydroxysuccinimide and p-toluenesulfonic acid is proposed as an efficient catalyst for the preparation of a great variety of imidazo[1,2-a]pyridine derivatives by three-component condensation of aromatic isocyanides, aldehydes, and 2-aminopyridine. The advantages of this procedure are high yields of the target products and the absence of side reactions. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1768–1772, October, 2006.     

Efficient and High-Yielding Protocol for the Synthesis of Nitriles from Aldehydes

An operationally simple and high-yielding procedure has been developed for the conversion of araldehydes into the corresponding nitriles using p-toluenesulfonic acid (p-TSA) (a mild catalyst) under microwave irradiation. The products are characterized by infrared spectral analysis and by comparison of the melting and boiling points with the reported values.     

Homogeneous and Heterogeneous Catalyzed Esterification of Acrylic Acid with Ethanol: Reaction Kinetics and Modeling

Kinetics of esterification of acrylic acid with ethanol in the presence of homogeneous (H₂SO₄, HCl, p‐TSA, HI) catalysts as well as heterogeneous catalysts (Dowex 50WX, Amberlyst 15) was studied. The effects and performance of these catalysts on the conversion of acrylic acid were evaluated. In the kinetics of homogeneous catalyzed reaction, both concentration and activity‐based model were employed. Activity coefficients were predicted by the Universal Functional group Contribution (UNIFAC) method to consider nonideal behavior of the liquid phase. The heterogeneous catalyzed reaction mechanisms were developed using Eley–Rideal theory. The model results were compared with the experimental results and were in good agreement. The temperature dependency of the constants, reaction enthalpy, and entropy, and activation energy were determined. The conversion of acrylic acid was obtained as 63.2%, 61.02%, 53.3%, 21.4%, 34.96%, and 14.84% for H₂SO₄, p‐TSA, HCl, HI, Dowex 50WX, and Amberlyst 15, respectively, under process temperature of 70°C, reactant molar ratio of 1:1, and catalyst concentration of 2% (v/v) for homogeneous and 2.17 g for heterogeneous catalyst. These outcomes provide an approach to understand the significant effect of each catalyst on the esterification kinetics of acrylic acid and ethanol.     

Low-Temperature Polyesterification of 3-Hydroxy-2-Phenylpropionic Acid

Abstract

The synthesis of poly(3-hydroxy-2-phenylpropionic acid), prepared from tropic acid and 1,3-dialkylcarbodiimide (cyclohexyl or isopropyl) with p-toluenesulfonic acid (PTSA) and/or dimethylaminopyridine (DMAP) as catalysts, has been investigated. Molecular weight and yield have been found to vary inversely with temperature and solvent polarity. Dialkylcarbodiimide activation of the carboxylic acid is enhanced when PTSA and DMAP are used in equal concentrations. Highest molecular weights and yields were achieved at ? 20°C with 50% (mol% of monomer) DMAP and PTSA in a cyclohexane/THF solvent system.     

SnCl4-Catalyzed Aza-Acetalization of Aromatic Aldehydes: Synthesis of Aryl Substituted 3,4-Dihydro-2H-1,3-benzoxazines

Stannic tetrachloride was an efficient Lewis acid catalyst for the aza-acetalization of aromatic aldehydes with o-arylaminomethyl phenols, and a series of novel aryl substituted 3,4-dihydro-2H-1,3-benzoxazines were prepared in good yields under mild conditions. SnCl₄ was a more efficient catalyst for the reaction than p-toluenesulfonic acid, sulfuric acid, and aluminium chloride.     

Activities of Co(II) Schiff base complexes in the redox carbonylation of aniline and nitrobenzene to methyl N-phenyl carbamate

The series of cobalt(II) complexes with different Schiff base ligands was synthesized and used as catalyst for the redox carbonylation of aniline and nitrobenzene. Effects of reaction temperature, CO pressure, promoter, and catalyst additions on the conversion of substrate were studied. When Co[(OH)₂saloph] — p-toluenesulfonic acid system was used as catalyst, the reaction was carried out at the next conditions: both Co[(OH)₂saloph] and p-toluenesulfonic acid—0.2 mmol, aniline—20 mmol, nitrobenzene—10 mmol, methanol—30 ml, Co—5 MPa, temperature 170°C, reaction time 7 h. The highest conversion of nitrobenzene and selectivity of methyl N-phenyl carbamate were 54.5 and 92.2%, respectively.     

One-step synthesis of a novel carbon-based strong acid catalyst through hydrothermal carbonization

Abstract  

A novel carbon-based strong acid catalyst was synthesized through the one-step hydrothermal carbonization of furaldehyde and p-toluenesulfonic acid (PTSA) in aqueous solution at 180 °C for only 4 h. The novel carbon-based solid acid possessed high acidity, and the catalytic activities were investigated by esterification and oxathioketalization. The results showed that the novel catalyst demonstrated much greater activity than the traditional solid acids and was comparable to sulfuric acid. The one-step method provides an efficient procedure for the synthesis of various functionalized carbons by one-step hydrothermal carbonization.     

Synthesis of levulinic acid–glycerol ketal–ester oligomers and structural characterization using NMR spectroscopy

Oligomerizations of renewable resources based monomers levulinic acid, and glycerol were studied using three different catalysts, Sb₂O₃, p-toluenesulfonic acid, and 1-(1-propylsulfonic)-3-methylimidazolium chloride. The highest average degree of oligomerization of 9.8 was achieved by heating an equimolar mixture of levulinic acid, and glycerol first from 23 to 210 °C under a nitrogen atmosphere for 1 h, and then at 210 °C under a vacuum for 9 h, in the presence of 1.0 mol% Sb₂O₃ catalyst. p-Toluenesulfonic acid, and 1-(1-propylsulfonic)-3-methylimidazolium chloride catalyzed reactions gave oligomers with relatively lower molecular weights. These levulinic acid–glycerol oligomers are shown to have ketal and ester links in a linear oligomer chain by using ¹H and ¹³C NMR spectroscopy. Three different types of terminal units: keto, glycerol-ketal, and glycerol-ester were identified with the help of model compounds, and their relative percentages were calculated using quantitative ¹H and ¹³C NMR data.     

1,3-Oxazolidin-4-ones. Synthesis and configuration of cis and trans isomers

Mixtures of cis and trans 1,3-oxazolidin-4-ones were obtained by cyclodehydration, in the presence of p-toluenesulfonic acid or boron trifluoride etherate, of lactamide and N-methyl-lactamide with aromatic and aliphatic aldehydes. The products were separated by column (silica) chromatography and their configurations were determined.     

Four-center type photopolymerization in the crystalline state. VI. Kinetic and structural study of the polymerization of p-phenylenediacrylic acid diethyl ester

The effect of temperature on the four-center type photopolymerization has been investigated for p-phenylenediacrylic acid diethyl ester over a wide temperature range including crystal transition point (56°C) and melting point (96°C) of monomer. With the elevation of temperature between ?50 and 15°C, the polymerization rate in the initial stage increased and the degree of polymerization decreased monotonously, while the rate in the later stage decreased above ?25°C. With irradiation at above 25°C, the monomer crystals became sticky, and the polymerization was suppressed at the stage of oligomerization with low conversion. This tendency was enhanced above the crystal transition point, giving mainly dimer in low yield. Above the melting point, only radical polymerization occurred with the aid of oxygen. The steric configuration of the products in the crystalline state was 1,3-trans with respect to the cyclobutane ring. Peaks in NMR spectra of all products were assigned to the protons involved in four compounds up to tetramer. Various results obtained have been interpreted in terms of the change, as a function of temperature, from a topochemical polymerization which proceeds under a control of the monomer lattice to a photoinitiated vinyl-type polymerization in the disordered state. It is concluded that a rigid crystal lattice is indispensable for the four-center type photopolymerization to proceed smoothly.     

A facile synthesis of α,α′-bis(substituted benzylidene) cycloalkanones catalyzed by p-TSA under solvent-free conditions

Abstract

Various 2,6-dibenzylidene cycloalkanones were readily prepared in a few minutes with good yields by simply mixing aromatic aldehydes with cycloalkanones in the presence of catalytic amounts of p-toluenesulfonic acid as a solid heterogeneous catalyst under solvent-free condition.     

Eco-friendly synthesis of esters under ultrasound with p-toluenesulfonic acid as catalyst

The present work describes the efficient ultrasound-assisted synthesis of saturated aliphatic esters from synthetic aliphatic acids in methanol or in ethanol, using p-toluenesulfonic acid as a catalyst. The esters were isolated in good yields after short reaction times under mild conditions. The compounds were analyzed by high resolution mass spectrometry (HRMS), which give a fragmentations pathway common for these molecules.     

Synthesis of dihydroxy telechelic oligomers of β-butyrolactone catalyzed by titanium(IV)-alkoxides and their use as macrodiols in polyurethane chemistry

We report on a solvent-free approach for the synthesis of low molecular weight, α,ω-dihydroxy telechelic poly(β-butyrolactone). In the presence of Ti(IV) alkoxides, mixtures of β-butyrolactone and diols, like di- or triethylene glycol, were reacted in ratios between 4:1 and 10:1. The oligomerization proceeds at elevated temperatures (80–100°C). Different alkoxide substituents (R = Me, iPr, tBu) of the Ti(IV)(OR)₄ catalyst were investigated. The resulting oligomers were characterized by nuclear magnetic resonance (NMR), infra-red (IR), gel-permeation chromatography (GPC), titration, and matrix-assisted laser desorption-time-of-flight mass spectrometry (MALDI-ToF-MS) analysis. Aside from low molecular weight products, special effort was devoted to achieve high O-acyl cleavage selectivity and to circumvent the formation of unsaturated end-groups in order to form exclusively dihydroxy-telechelic oligomers. Optimized results in terms of selectivity and reaction rates were achieved at 100°C using catalyst loadings of 0.2 mol% with respect to the monomer. The molecular weights determined by GPC were in good accordance with the ratio of monomer to diol used, confirming successful oligomer formation. Polyurethanes prepared from crude macrodiols without any additional catalyst feature molecular weights up to 50,000 g/mol. The reported work serves as concept to utilize β-lactones for tailored polyol synthesis; the resulting products are suitable for polyurethane chemistry.     

Kinetics,mass transfer,and thermodynamic and statistical modeling study for esterification of valeric acid with n‐butanol: Homogeneous and heterogeneous catalysis

The esterification of valeric acid with n‐butanol was studied with homogeneous and heterogeneous catalysts. The activity and performance of homogeneous p‐toluenesulfonic acid and heterogeneous cation exchange resin catalysts Amberlyst 36, Indion 190, and Amberlite IRC‐50 were evaluated. The pseudo‐homogeneous kinetic model was used to investigate the kinetic parameters of homogeneous‐ and heterogeneous‐catalyzed esterification. The UNIFAC (universal functional activity coefficient) approach was used to study the nonideality of the esterification reaction. The reaction was statistically modeled and optimized by the application of response surface methodology. The effects of independent variables such as reaction temperature, initial molar ratio, and catalyst loading on the conversion of valeric acid were investigated. The optimized conditions for the esterification reaction catalyzed by Amberlyst‐36 were found as temperature 360.4 K, initial molar ratio 3.8, and catalyst loading 6.7 wt%. The predicted conversion (89%) at these optimized conditions is in good agreement with the experimental conversion (87.3 ± 1.6%).     

A novel eco-friendly on-water protocol for the synthesis of 2,2-disubstituted 2,3-dihydro-1H-perimidines

An efficient green on-water protocol for the synthesis of 2,2-disubstituted 2,3-dihydro-1H-perimidines is demonstrated. The reaction used safer p-toluenesulfonic acid (PTSA) as a catalyst on water at 80°C, for 2 hours affording a novel method for the synthesis of various disubstituted perimidines in moderate to excellent yields.     

Facile One‐Pot Multicomponent Synthesis of β‐Acetamido Ketones with Amberlyst‐15 as Heterogeneous Catalyst

The one‐pot multicomponent coupling of an aromatic aldehyde, an enolizable ketone or keto ester, acetonitrile, and acetyl chloride at room temperature in the presence of Amberlyst‐15 as catalyst affords β‐acetamido ketones in high yields. The inexpensive catalyst works under heterogeneous conditions and can be readily reused.     

Highly efficient heterogeneous acylations of aromatic compounds with acid anhydrides and carboxylic acids by montmorillonite-enwrapped titanium as a solid acid catalyst

Montmorillonite-enwrapped titanium hydroxide species (Ti⁴⁺-mont) acted as a highly efficient heterogeneous acid catalyst for the acylation of aromatic compounds with acid anhydrides or carboxylic acids. The catalytic activity of the Ti⁴⁺-mont was higher than those of other acid catalysts such as zeolites, SO ₄ ²⁻ /ZrO₂ and p-toluenesulfonic acid. For example, the reaction of anisole with dodecanoic acid in the presence of the Ti⁴⁺-mont catalyst gave 1-(4-methoxyphenyl)-1-dodecanone in 97% yield. Furthermore, the Ti⁴⁺-mont catalyst was easily separated from the reaction mixture and was recyclable.