Interferences in electrochemical hydride generation of hydrogen selenide

Interferences from Cu(II), Zn(II), Pt(IV), As(III) and nitrate on electrochemical hydride generation of hydrogen selenide were studied using a tubular flow-through generator, flow injection sample introduction and quartz tube atomic absorption spectrometry. Comparison with conventional chemical generation using tetrahydroborate was also performed. Lead and reticulated vitreous carbon (RVC), both in particulate form, were used as cathode materials. Signal supressions up to 60–75%, depending on the cathode material, were obtained in the presence of up to 200 mg l⁻¹ of nitrate due to the competitive reduction of the anion. Interference from As(III) was similar in electrochemical and chemical generation, being related to the quartz tube atomization process. Zinc did not interfere up to Se/Zn ratios 1:100, whereas copper and platinum showed suppression levels up to 50% for Se/interferent ratios 1:100. Total signal suppression was observed in presence of Se/Cu ratios 1:100 when RVC cathodes were used. No memory effects were observed in any case. Scanning electron microscopy and squared wave voltametry studies supported the interference mechanism based on the decomposition of the hydride on the dispersed particles of the reduced metal.     

Effect of cathodic electrolyte on the performance of electrochemical hydride generation from graphite cathode

The classic silver diethyldithiocarbamate (SDDC) spectrophotometric procedure for arsenic determination has been used for investigation of the effect of cathodic electrolyte on the performance of electrochemical hydride generation (HG) from graphite cathode. The results of this study show that the presence of a soft metal ion such as Cd(II), Sn(II) and/or Zn(II) in the acidic cathodic electrolyte can increase effectively the efficiency of electrochemical hydride generation and decrease the effect of interferences. The possible mechanisms of these effects have been discussed in detail. The parameters related to the electrochemical hydride generation were investigated. Also the characteristic data of the electrochemical hydride generation and common hydride generation by NaBH₄ were compared. Under optimised conditions, the system is selective to As(III) and total inorganic analyses can be performed after a pre-reduction stage prior to electrochemical hydride generation. This will allow the differential determination of inorganic arsenic species. The method is appropriate to the determination of 4-40 μg of each arsenic species.     

Flow injection on-line solid phase extraction for ultra-trace lead screening with hydride generation atomic fluorescence spectrometry

A flow injection (FI) on-line solid phase extraction (SPE) procedure for ultra-trace lead separation and preconcentration was developed, followed by hydride generation and atomic fluorescence spectrometric (AFS) detection. Lead is retained on an iminodiacetate chelating resin packed microcolumn, and is afterward eluted with 2.5% (v/v) hydrochloric acid to facilitate the hydride generation by reaction with alkaline tetrahydroborate solution with 1% (m/v) potassium ferricyanide as an oxidizing (or sensitizing) reagent. The hydride was separated from the reaction medium in the gas-liquid separator and swept into the atomizer for quantification. The chemical variables and the FI flow parameters were carefully optimized. With a sample loading volume of 4.8 ml, quantitative retention of lead was obtained, along with an enrichment factor of 11.3 and a sampling frequency of 50 h(-1). A detection limit of 4 ng l(-1), defined as 3 times the blank standard deviation (3 sigma), was achieved along with a RSD value of 1.6% at the 0.4 microg l(-1) level. The procedure was validated by determining lead contents in two certified reference materials, and its practical applicability was further demonstrated by analysing a variety of biological and environmental samples.     

Flow injection hydride generation electrothermal atomic absorption spectrometry with in-atomizer trapping for the determination of lead in calcium supplements

Lead hydride was generated from acid solution, containing potassium ferricyanide as an oxidizing agent, by the reaction with alkaline borohydride solution. The effects of reaction conditions (hydrochloric acid, ferricyanide and borohydride concentrations), and the lengths of reaction and stripping coils were studied. The effects of trapping temperature and argon flow rate were also investigated. Under the conditions giving the best peak area sensitivity, the detection limit (concentration giving a signal equal to three S.D. of the blank signal) was 0.12 mug l(-1) for a 1000 mul injection volume. The detection limit was improved to 0.03 mug l(-1) when the ferricyanide was purified by passage through a cation-exchange resin. Two calcium supplement materials were analyzed by the flow injection (FI)-hydride generation (HG)-electrothermal atomization atomic absorption spectrometry (ETAAS) method, giving values of 0.55 and 0.66 mug g(-1), in agreement with results obtained by previously validated methods. For a 500-mg sample the limits of detection and quantification were 0.006 and 0.02 mug g(-1), respectively.     

Determination of lead in dialysis concentrates using flow injection hydride generation atomic absorption spectrometry

Flow injection hydride generation atomic absorption spectrometry (FI-HGAAS) was used for determination of lead in dialysis concentrates. The parameters such as acidity, concentration of oxidising and reducing agents and argon gas flow rate were investigated to reach the best peak height sensitivity. No significant background signal was observed at high salt concentrations. The detection limit, concentration giving a signal equal to three times standard deviation of the blank signal, was 0.7 ng ml⁻¹ for a 500 μl injection volume. Precision of the measurements at the 20 ng ml⁻¹ level was 3.7% R.S.D. The dialysis concentrates analysed by FI-HGAAS were found to have 10-70 ng ml⁻¹ of lead. The same samples were analysed by ETAAS after removing the matrix using solid phase extraction with Chelex 100. The results were in agreement with those obtained by FI-HGAAS.     

Flow injection on-line acid digestion and pre-reduction of arsenic for hydride generation atomic absorption spectrometry-a feasibility study

A flow injection (FI) manifold is described which makes possible on-line microwave-assisted acid digestion, followed by pre-reduction of As(V) to As(III) and its determination by hydride generation atomic absorption spectrometry. The merging zone technique is used in order to reduce acid consumption for digestion. The efficiency of acid digestion is increased by pressure which is built up in-line by a flow restrictor. Flows for sample pretreatment and hydride generation can be optimized independently. L-cysteine was found superior to potassium iodide as the pre-reductant because much lower reagent and acid concentrations are required, much harsher conditions can be tolerated for acid digestion, and the integrated absorbance signals for arsenic in blood and standards are essentially identical, making possible the use of the standard calibration procedure.

The sampling frequency is 7–10/hr, depending on the conditions chosen, and the limit of detection, i.e. the concentration giving a signal equal to three times the standard deviation of the signal of the blank solution, is 0.25 μg/l for a 500 μl sample volume. The recovery of 10 μg/l As(V) added to a blood sample was 94 ± 2 and 98 ± 2% (n = 3) in absorbance and integrated absorbance, respectively.     

Flow injection electrochemical hydride generation inductively coupled plasma time-of-flight mass spectrometry for the simultaneous determination of hydride forming elements and its application to the analysis of fresh water samples

A flow injection (FI) method was developed using electrochemical hydride generation (EcHG) as a sample introduction system, coupled to an inductively coupled plasma time-of-flight mass spectrometer (ICP-TOFMS) for rapid and simultaneous determination of six elements forming hydrides (As, Bi, Ge, Hg, Sb and Se). A novel low volume electrolysis cell, especially suited for FI experiments was designed and the conditions for simultaneous electrochemical hydride generation (EcHG; electrolyte concentrations and flow rates, electrolysis voltage and current) as well as the ICP-TOFMS operational parameters (carrier gas flow rate, modulation pulse width (MPW)) for the simultaneous determination of 12 isotopes were optimized. The compromise operation parameters of the electrolysis were found to be 1.4 and 3 ml min⁻¹ for the anolyte and catholyte flow rates, respectively, using 2 M sulphuric acid. An optimum electrolysis current of 0.7 A (16 V) and an argon carrier gas flow rate of 0.91 l min⁻¹ were chosen. A modulation pulse width of 5 μs, which influences the sensitivity through the amount of ions being collected by the MS per single analytical cycle, provided optimum results for the detection of transient signals. The achieved detection limits were compared with those obtained by using FI in combination with conventional nebulization (FI-ICP-TOFMS); values for chemical hydride generation (FI-CHG-ICP-TOFMS) were taken from the literature. By using a 200 μl sample loop absolute detection limits (3σ) in the range of 10-160 pg for As, Bi, Ge, Hg, Sb and 1.1 ng for Se and a precision of 4-8% for seven replicate injections of 20-100 ng ml⁻¹ multielemental sample solutions were achieved. The analysis of a standard reference material (SRM) 1643d (NIST, “Trace Elements in Water”) showed good agreement with the certified values for As and Sb. Se showed a drastic difference, which is probably due to the presence of hydride-inactive Se species in the sample. Recoveries better than 93% for Ge and Hg and 83.9% for Se were achieved on a spiked SRM sample. The developed method was successfully applied to the simultaneous multielemental determination of hydride forming elements in spring water samples originating from two different regions in Hungary.     

Flow injection electrochemical hydride generation atomic absorption spectrometry (FI-EHG-AAS) as a simple device for the speciation of inorganic arsenic and selenium

A flow-injection system for the determination of inorganic arsenic [As(III)/As(V)] and selenium species [Se(IV)/ Se(VI)] by electrochemical hydride generation, cryogenic trapping and atomic absorption spectrometry is described. A simple and robust electrochemical flow-through cell with fibrous carbon as cathodic material has been developed for the speciation of arsenic. A cold-trap system makes possible to eliminate interferences from methylated arsenic species. Without pre-reduction the system is selective to As(III) and Se(IV). The selectivity obtained with fibrous carbon as cathode material is compared to the selectivity obtained with a second electrochemical flow-through cell using a lead foil as cathode.     

Determination of lead by hydride generation atomic absorption spectrometry : Part 1. A new medium for generating hydride

A new medium, used to generate lead hydride, was optimized as 0.3% (w/v) oxalic acid-2% (w/v) ammonium cerium (III) nitrate-8% (w/v) potassium tetrahydroborate-1% (w/v) sodium hydroxide solution; 950°C is used for atomization. The characteristic concentration (0.0044 absorbance) obtained under these conditions was 0.04 ng ml^?1. The application of this medium to soil and ferromagano-brass samples is illustrated.     

Flow injection hydride generation electrothermal atomic absorption spectrometric determination of toxicologically relevant arsenic in urine

Analytical procedure for the determination of toxicologically relevant arsenic (the sum of arsenite, arsenate, monomethylarsonate and dimethylarsinate) in urine by flow injection hydride generation and collection of generated inorganic and methylated hydrides on an integrated platform of a transverse-heated graphite atomizer for electrothermal atomic absorption spectrometric determination (ETAAS) is elaborated. Platforms are pre-treated with 2.7 μmol of zirconium and then with 0.10 μmol of iridium which serve both as an efficient hydride sequestration medium and permanent chemical modifier. Arsine, monomethylarsine and dimethylarsine are generated from diluted urine samples (10–25-fold) in the presence of 50 mmol L⁻¹ hydrochloric acid and 70 mmol L⁻¹ l-cysteine. Collection, pyrolysis and atomization temperatures are 450, 500, 2100 and 2150 °C, respectively. The characteristic mass, characteristic concentration and limit of detection (3σ) are 39 pg, 0.078 μg L⁻¹ and 0.038 μg L⁻¹ As, respectively. The limits of detection in urine are ca. 0.4 and 1 μg L⁻¹ with 10- and 25-fold dilutions. The sample throughput rate is 25 h⁻¹. Applications to several urine CRMs are given.     

Determination of lead in wines by hydride generation atomic absorption spectrometry.

The optimization of lead hydride generation in aqueous ethanolic media and the influence on its generation of the wine components, both white and red, have been studied. These interferences were overcome by careful control of the parameters affecting hydride generation and the procedure was applied to the determination of Pb in wines. The method is fast, accurate and sensitive and can be used to quantify 24 ppb of Pb in wines.     

Comparison of palladium and zirconium treated graphite tubes for in-atomizer trapping of hydrogen selenide in hydride generation electrothermal atomization atomic absorption spectrometry

Zirconium treated graphite tubes were investigated and compared with non-treated and palladium coated ones for in situ trapping of selenium hydride generated in a flow injection system. Selenium was effectively trapped on zirconium treated tubes at trapping temperatures of 300–600°C, similar to those observed for palladium, whereas trapping temperatures higher than 600°C had to be used with non-treated tubes. Zirconium treated tubes used in this work showed good stability up to 300 trapping/atomization cycles, with precision better than 5%, characteristic masses of 42 (peak height) and 133 pg (peak area) of selenium were obtained. Sensitivity of zirconium and palladium treatments were similar, but zirconium offered the advantage of a single application per tube. Detection limits were 0.11 (peak height) and 0.23 ng (peak area) for a 1 ml sample volume.     

Studies on the influence of various experimental conditions on electrochemical generation of ferrate(VI) in NaOH-KOH mixed electrolyte

Ferrate(VI) was prepared by electrooxidation in diaphragm electrolyzer with iron wire gauze as anode and NaOH-KOH mixed solution as electrolyte. The influences of various experimental conditions, such as the volume ratio of NaOH-KOH mixed electrolyte, temperature, current density, passivation of iron anode were investigated on ferrate current efficiency. Due to the low solubility of K₂FeO₄ in concentrated alkaline solution and the passivation of iron wire gauze anode, a highest current efficiency over 90% was obtained at 45°C and at a current density of 5 mA cm⁻² in mixed electrolyte with the volume ratio of NaOH: KOH equal to 6: 4. The result is superior to using NaOH and KOH as electrolyte respectively. In addition, polarization curves, scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) were employed to further study the effects of synthesis conditions on ferrate(VI) in theory. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 853–857. The article is published in the original.     

流动注射-电化学氧化法测定水体化学需氧量

采用硼掺杂金刚石(Boron-doped diamond,BDD)薄膜电极为工作电极,利用流动注射分析方法测定水体化学需氧量(COD),根据水样中有机物组分在工作电极表面氧化消耗的电量(Qoxidation)测定样品的COD值。考察了一些基本参数包括载液、工作电位、流速对检测信号的影响并选定了最佳检测条件。在最佳检测条件下,本法检测COD的线性范围为2.5~120 mg/L,检出限为1 mg/L。用该法测定化工厂和食品厂废水的COD值,相对标准偏差和回收率分别在2.4%~4.8%和96%~106%之间,且检测结果与国家标准方法(CODcr法)有良好的一致性。     

Flow injection on-line preconcentration coupled to hydride generation atomic fluorescence spectrometry for ultra-trace amounts of cadmium determination in seawater

A simple flow injection on line separation and preconcentration system coupled to hydride generation atomic fluorescence spectrometry (HG-AFS) was developed for ultra-trace cadmium determination in seawater. With the sample pH kept at 3.0, the preconcentration of cadmium on the inner walls of the knotted reactor was carried out based on the retention of cadmium complex with 1-phenyl-3-methyl-4-benzoylpyrazol-5-one. A 0.2 mol L⁻¹ HCl was introduced to elute the retained analyte complex and merge with KBH₄ solution for HG-AFS detection. Under the optimal experimental conditions, an enhancement factor of 12 was obtained with a sample consumption of 12.0 mL. The limit of detection was 3.2 ng L⁻¹ with a sample frequency of 24 h⁻¹. The developed method was validated by the analysis of cadmium in certified reference materials, and was applied to the determination of cadmium in four seawater samples with R.S.D. of around 10%. Correspondence: Hong Wu, Department of Chemistry, Xuzhou Normal University, Xuzhou 221116, P.R. China     

Investigations for the determination of tin by flow injection hydride generation atomic-absorption spectrometry

It could be shown that the pre- or double peaks which are frequently observed in the determination of tin by hydride generation atomic-absorption spectrometry are not due to reagent contamination or memory effects. Rather they originate from the silica material used to make the quartz tube atomizer. At elevated temperatures the tin diffuses to the surface and it can be volatilized and atomized only in the presence of hydrogen. The height of the pre-peak depends, among other things, on the time for which the quartz tube atomizer has been at a high temperature without hydrogen. The pre-peaks disappear when argon with 10% (v/v) hydrogen is used as the purge gas. In flow injection the pre-peaks can be separated in time from the analytical signal by using a program in which hydrogen is generated by reaction of sodium tetrahydroborate reluctant solution with the acid carrier prior to the injection of the sample. Also investigated was the influence of the acid and sodium tetrahydroborate concentration on sensitivity and freedom from interferences. Best results were obtained when a saturated boric acid solution containing 0.1M hydrochloric acid was used for standards, samples and carrier solution, and a 0.4% (m/v) sodium tetrahydroborate solution with 0.05% (m/v) sodium hydroxide as the reluctant. Under these conditions tin could be determined accurately in the range 0.008-0.1% in low alloy steel standard reference materials, with matrix-free standard solutions for calibration.     

A photoelectrochemical study of anodic oxides on lead selenide surfaces in alkaline solutions

Lead selenide is a narrow gap semiconductor material. It finds applications in infrared emitting and detecting devices. Their performance is closely related to charge carrier recombination at the surface, which can be reduced by passivation, e.g. due to PbSeO₃ formation by anodic oxidation in alkaline solutions. In dependence on the pretreatment of the surface, two different types of oxide formation were observed. To determine the electronic properties of the anodic oxide, the wavelength dependence of the photocurrent was investigated. The energy of the band gap of both types of anodic oxide on PbSe has been determined to be 2.4 eV for the direct and 1.8 eV for the indirect band gap. A weakening of the photocurrent generated in the bulk (PbSe) due to scattering or absorption within the oxide confirms the potential dependence of the oxide thickness for a high field growth mechanism.