Spectrophotometric determination of formaldehyde with chromotropic acid in phosphoric acid medium assisted by microwave oven

In the present study, a spectrophotometric method for the determination of formaldehyde by using chromotropic acid was devised, in which the use of potentially hazardous and corrosive concentrated sulfuric acid was eliminated and advantageously replaced by a mixture of H₃PO₄ and H₂O₂. The reaction between formaldehyde and chromotropic acid (CA) in a concentrated phosphoric acid medium was accelerate by irradiating the mixture with microwave energy for 35 s (1100 W), producing a violet-red compound (λ_max=570 nm). Beer's Law is obeyed in a concentration range of 0.8-4.8 mg l⁻¹ of formaldehyde with a good correlation coefficient (r=0.9968). The proposed method was applied in the analysis of formaldehyde in commercial disinfectants. Recoveries were within 98.0-100.4%, with standard deviations ranging from 0.03 to 0.13%.     

Mechanistic study of iodide catalysed oxidation of l-glutamic acid by cerium(IV) in aqueous sulphuric acid medium

A minute quantity (10⁻⁶ mol dm⁻³) of iodide catalysed oxidation of l-glutamic acid by Ce^IV has been studied in H₂SO₄ and SO ₄ ²⁻ media. The reaction was first order each in [Ce^IV] and [I⁻]. The order with respect to [l-glutamic acid] was less than unity (0.71). Increase in [H₂SO₄] decreased the reaction rate. The added HSO ₄ ⁻ and SO ₄ ²⁻ decreased the rate of reaction. The added product, succinic acid, had no effect on the reaction rate, whereas added Ce^III retarded the reaction. The ionic strength and dielectric constant did not have any significant effect on the rate of reaction. The active species of oxidant was Ce(SO₄)₂. A suitable mechanism was proposed. The activation parameters were determined with respect to the slow step of the mechanism. The thermodynamic quantities were also determined and discussed.     

Effect of medium acidity on the efficiency of oxidation of 2,4,6-trinitrotoluene to 2,4,6-trinitrobenzoic acid

An effect of boric acid additives on oxidation of 2,4,6-trinitrotoluene (TNT) to 2,4,6-trinitrobenzoic acid (TNBA) with chromic anhydride in concentrated (96—100%) H₂SO₄ has been studied. In the presence of tetrahydrosulfatoboric acid HB(HSO₄)₄ formed in situ (up to 5 mol.%) or added as a preliminary prepared solution (up to 1 mol. %), TNT is selectively oxidized to TNBA in the yields up to 95—99%. The mechanism including formation of TNT dication as a key step of its oxidation at the methyl group has been suggested.     

Chlorine and sulfur determination in extra-heavy crude oil by inductively coupled plasma optical emission spectrometry after microwave-induced combustion

In this study, microwave-induced combustion (MIC) of extra-heavy crude oil is proposed for further chlorine and sulfur determination by inductively coupled plasma optical emission spectrometry (ICP OES). Combustion was carried out under oxygen pressure (20 bar) in quartz vessels using ammonium nitrate (50 µl of 6 mol l^− 1 solution) as ignition aid. Samples were wrapped with polyethylene film and placed on a quartz holder positioned inside the quartz vessels. The need for an additional reflux step after combustion and the type and concentration of absorbing solution (water, 0.02 to 0.9 mmol l^− 1 H₂O₂, 10 to 100 mmol l^− 1 (NH₄)₂CO₃ or 0.1 to 14 mol l^− 1 HNO₃) were studied. The influence of sample mass, O₂ pressure and maximum pressure attained during the combustion process were investigated. Recoveries from 92 to 102% were obtained for Cl and S for all absorbing solutions. For comparison, Cl and S determination was also performed by ion chromatography (IC) using 25 mmol l^− 1 (NH₄)₂CO₃ as absorbing solution. Using MIC with a reflux step the agreement was better than 95% for certified reference materials of similar composition (crude oil, petroleum coke, coal and residual fuel oil). Microwave-assisted digestion and water extraction in high pressure closed vessels were also evaluated. Using these procedures the maximum recoveries were 30 and 98% for Cl and S, respectively, using microwave-assisted digestion and 70% for Cl and less than 1% for S by water extraction procedure. Limits of detection by ICP OES were 12 and 5 µg g^− 1 for Cl and S, respectively, and the corresponding values by IC were 1.2 and 8 µg g^− 1. Using MIC it was possible to digest simultaneously up to eight samples resulting in a solution suitable for the determination of both analytes with a single combustion step.     

Extraction of arsenic compounds from lichens

Different extraction procedures were applied to improve the extraction efficiency of arsenic compounds from lichens. Two lichen species were chosen from an arsenic-contaminated environment: epiphytic Hypogymnia physodes (L.) Nyl. and terricolous Cladonia rei Schaer. Samples were extracted with water at temperatures of 20, 60 and 90 °C, using mixtures of methanol/water (9:1, 1:1 and 1:9), Tris buffer and acetone and the extracts speciated. Water and Tris buffer showed the best extraction efficiency of all extractants used; however, the extraction efficiency was still less than 23%. Since a major fraction of arsenic appeared to be associated with trapped soil particles, a sequential extraction procedure originally designed for soils (extraction steps: (1) 0.05 mol l⁻¹ (NH₄)₂SO₄; (2) 0.05 mol l⁻¹ (NH)₄H₂PO₄; (3) 0.2 mol l⁻¹ NH₄-oxalate buffer, pH 3.25; (4) mixture of 0.2 mol l⁻¹ NH₄-oxalate buffer and 0.1 mol l⁻¹ ascorbic acid, pH 3.25; (5) 0.5 mol l⁻¹ KOH) was applied and found to remove 45% of the total arsenic from H. physodes and 83% from C. rei. The lipid-soluble fraction of arsenic was estimated by k₀-INAA analysis of diethylether extracts and was found to be negligible. An HPLC-UV-HGAFS system was used to determine the arsenic compounds extracted. In both lichen species, arsenous acid, arsenic acid, monomethylarsonic acid, dimethylarsinic acid, arsenobetaine, trimethylarsine oxide and glycerol-ribose were detected. In addition, phosphate-ribose was found in H. physodes.     

Electrochemical Synthesis of Co-intercalation Compounds in the Graphite-H<Subscript>2</Subscript>SO<Subscript>4</Subscript>-H<Subscript>3</Subscript>PO<Subscript>4</Subscript>System

Anodic oxidation of highly oriented pyrolytic graphite in an electrolyte containing concentrated sulfuric and anhydrous phosphoric acids is studied for the first time. The synthesis was carried out under galvanostatic conditions at a current I = 0.5 mA and an elevated temperature (t = 80°C). Intercalation compounds of graphite (ICG) are shown to form at all concentration ratios of H₂SO₄ and H³PO⁴ acids. The intercalation compound of step I forms in solutions containing more than 80 wt % H₂SO₄, a mixture of compounds of intercalation steps I and II forms in 60% H²SO⁴, intercalation step II is realized in the sulfuric acid concentration range from 10 to 40%, and a mixture of compounds of intercalation steps III and II is formed in 5% H₂SO₄ solutions. The threshold concentration of H₂SO₄ intercalation is ∼2%. With the decrease in active intercalate (H₂SO₄) concentration, the charging curves are gradually smoothed, the intercalation step number increases, and the potentials of ICG formation also increase. As the sulfuric acid concentration in the electrolyte changes from 96 to 40 wt %, the filled-layer thickness d _i in ICG monotonously increases from 0.803 to 0.820 nm, which apparently is associated with the greater size of phosphoric acid molecules. With further increase in H₃PO₄ concentration in solution, d _i remains unchanged. According to the results of chemical analysis, both acids are simultaneously incorporated into the graphite interplanar spacing and their ratio in ICG is determined by the electrolyte composition.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 651–655.Original Russian Text Copyright © 2005 by Leshin, Sorokina, Avdeev.     

Immobilization of horseradish peroxidase to a nano-Au monolayer modified chitosan-entrapped carbon paste electrode for the detection of hydrogen peroxide

A procedure for fabricating an enzyme electrode has been described based on the effective immobilization of horseradish peroxidase (HRP) to a nano-scaled particulate gold (nano-Au) monolayer modified chitosan-entrapped carbon paste electrode (CCPE). The high affinity of chitosan entrapped in CCPE for nano-Au associated with its amino groups has been utilized to realize the use of nano-Au as an intermediator to retain high bioactivity of the enzyme. Hydrogen peroxide (H₂O₂) was determined in the presence of hydroquinone as a mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano-Au displayed excellent electrocatalytical activity to the reduction of H₂O₂. The effects of experimental variables such as the operating potential of the working electrode, mediator concentration and pH of measuring solution were investigated for optimum analytical performance by using an amperometric method. The enzyme electrode provided a linear response to hydrogen peroxide over a concentration range of 1.22×10⁻⁵-2.43×10⁻³ mol l⁻¹ with a sensitivity of 0.013 A l mol⁻¹ cm⁻² and a detection limit of 6.3 μmol l⁻¹ based on signal per noise =3. The apparent Michaelis-Menten constant (K_m^app) for the sensor was found to be 0.36 mmol l⁻¹. The lifetime, fabrication reproducibility and measurement repeatability were evaluated with satisfactory results. The analysis results of real sample by this sensor were in satisfactory agreement with those of the potassium permanganate titration method.     

On-line determination of mercury(II) by membrane separation flow injection analysis

A rapid and inexpensive gas-diffusion (GD) flow injection method for the on-line determination of Hg(II) in aqueous samples is described. The analytical procedure involves the injection of a Hg(II) sample into a 1.5 M H₂SO₄ carrier stream which is merged with a reagent stream containing 0.6% SnCl₂ and 1.5 M H₂SO₄. Under these conditions Hg(II) is reduced to metallic mercury which partially evaporates through a Teflon membrane into an acceptor stream containing 1.75×10⁻⁴ M KMnO₄ in 0.3 M H₂SO₄. The decrease in the absorbance of the acceptor stream at 528 nm corresponding to the absorption maximum of the permanganate anion can be related to the original concentration of Hg(II) in the sample. The method is characterized by a detection limit of 4 μg l⁻¹ and a sampling frequency of 8 h⁻¹. The flow system was successfully applied to the analysis of river samples spiked with Hg(II).     

Chemiluminescence system for automatic determination of chemical oxygen demand using flow injection analysis

A novel chemiluminescence (CL) system for automatic determination of chemical oxygen demand (COD) combined with flow injection analysis is proposed in this paper. In this system, potassium permanganate is reduced to Mn²⁺ which is first adsorbed on a strongly acid cation-exchange resin mini-column to be concentrated during chemical oxidation of the organic compounds at room temperature, while the excessive MnO₄⁻ passes through the mini-column to be waste, then the concentrated Mn²⁺ is eluted reversely and measured by the luminol-H₂O₂ CL system. The calibration graph is linear in the range of 4-4000 mg l⁻¹ and the detection limit is 2 mg l⁻¹. A complete analysis could be performed in 1.5 min including washing and sampling, giving a throughout of about 40 h⁻¹. The relative standard deviation was 4.4% for 10 mg l⁻¹ COD (n=11), 4.8% for 100 mg l⁻¹ COD (n=11). This CL flow system for determination of COD is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to the determination of COD of water samples.     

Highly sensitive catalytic determination of molybdenum

A novel, highly sensitive, selective, and simple kinetic method was developed for the determination of Mo(VI) based on its catalytic effect on the oxidation of 1-amino-2-naphthol-4-sulfonic acid (ANSA) with H₂O₂. The reaction was followed spectrophotometrically by tracing the oxidized product at 465 nm after 30 min of mixing the reagents. The optimum reaction conditions were: 10 mmol l⁻¹ ANSA, 50 mmol l⁻¹ H₂O₂, 100 mmol l⁻¹ acetate buffer of pH 5.0 ± 0.05 and at 40 °C. Addition of 200 μg ml⁻¹ diethylenetriaminepentaacetic acid (DTPA) conferred high selectivity for the proposed method. Following the recommended procedure, Mo(VI) could be determined with a linear calibration graph up to 2.5 ng ml⁻¹ and a detection limit, based on the 3S_b-criterion, of 0.027 ng ml⁻¹. The unique sensitivity and selectivity of the implemented method allowed its direct application to the determination of Mo(VI) in natural and industrial waste water. The method was validated by comparison with the standard ETAAS method. Moreover, published catalytic-spectrophotometric methods for the determination of molybdenum were reviewed.     

Cerium (IV) oxidation rate of p-chloromandelic acid in perchlorate and sulfate media

The rate of the cerium (IV) oxidation of p-chloromandelic acid has been studied in perchlorate media at an ionic strength of 1.50 mol/dm³ by the stopped-flow technique and in H₂SO₄? MHSO₄ (M⁺ = Li⁺, Na⁺, K⁺) and H₂SO₄? MClO₄ (M⁺ = H⁺, Li⁺, Na⁺) mixtures at constant total electrolyte concentrations of 1.00 and 2.00 mol/dm³ using the conventional spectrophotometric method. In perchlorate media the kinetic data indicate the formation of two intermediate complexes between cerium (IV) and the organic substrate, but only one is significantly involved in the intramolecular electron-transfer process. The oxidation rate is markedly lower in sulfate media, where two reaction paths have been found to contribute to the overall redox reaction. The univalent cations examined exhibit negative specific effects upon the overall oxidation rate increasing in the order H⁺ < Li⁺ < Na⁺ < K⁺. Activation parameters have been also estimated.     

Osmium(VIII) mediated oxidation of mercury(I) by cerium(IV) in aqueous sulphuric acid – a kinetic and mechanistic study

The oxidation of Hg^I by Ce^IV has been studied in aqueous H₂SO₄. A minute amount (10^–6 mol dm^–3) of Os^VIII is sufficient to catalyse the reaction. The active catalyst, substrate and oxidant species are H₂OsO₅, [Hg₂(SO₄)HSO₄]^– and H₃Ce(SO₄)^– ₄, respectively. Possible mechanisms are proposed and the reaction constants involved have been determined.     

Study on photocatalytic oxidation for determination of the low chemical oxygen demand using a nano-TiO2-Ce(SO4)2 coexisted system

A new photocatalytic system, nano-TiO₂-Ce(SO₄)₂ coexisted system, which can be used to determine the low chemical oxygen demand (COD) is described. Nano-TiO₂ powders is used as photocatalyst in this system. The measuring method is based on direct determination of the concentration change of Ce(IV) resulting from photocatalytic oxidation of organic compounds. The mechanism of the photocatalytic oxidation for COD determination was discussed and the optimum experimental conditions were investigated. Under the optimum conditions, a good calibration graph for COD values between 1.0 and 12 mg l⁻¹ was obtained and the LOD value was achieved as low as 0.4 mg l⁻¹. When determining the real samples, the results were in good agreement with those from the conventional methods.     

Dark Fermentative Hydrogen Production from Neutralized Acid Hydrolysates of Conifer Pulp

Concentrated acid hydrolysis of cellulosic material results in high dissolution yields. In this study, the neutralization step of concentrated acid hydrolysate of conifer pulp was optimized. Dry conifer pulp hydrolysis with 55?% H₂SO₄ at 45?°C for 2?h resulted in total sugar yields of 22.3?C26.2?g/L. The neutralization step was optimized for solid Ca(OH)₂, liquid Ca(OH)₂ or solid CaO, mixing time, and water supplementation. The highest hydrogen yield of 1.75?mol?H₂/mol glucose was obtained with liquid Ca(OH)₂, while the use of solid Ca(OH)₂ or CaO inhibited hydrogen fermentation. Liquid Ca(OH)₂ removed sulfate to below 30?mg SO₄ ^2?/L. Further optimization of the neutralization conditions resulted in the yield of 2.26?mol?H₂/mol glucose.     

Thermodynamic representation of the NaCl + Na2SO4 + H2O system with electrolyte NRTL model

A comprehensive thermodynamic model based on the electrolyte NRTL (eNRTL) activity coefficient equation is developed for the NaCl + H₂O binary, the Na₂SO₄ + H₂O binary and the NaCl + Na₂SO₄ + H₂O ternary. The NRTL binary parameters for pairs H₂O-(Na⁺, Cl⁻) and H₂O-(Na⁺, SO₄²⁻), and the aqueous phase infinite dilution heat capacity parameters for ions Cl⁻ and SO₄²⁻ are regressed from fitting experimental data on mean ionic activity coefficient, heat capacity, liquid enthalpy and dissolution enthalpy for the NaCl + H₂O binary and the Na₂SO₄ + H₂O binary with electrolyte concentrations up to saturation and temperature up to 473.15 K. The Gibbs energy of formation, enthalpy of formation and heat capacity parameters for solids NaCl_(s), NaCl·2H₂O_(s), Na₂SO_4(s) and Na₂SO₄·10H₂O_(s) are obtained by fitting experimental data on solubilities of NaCl and Na₂SO₄ in water. The NRTL binary parameters for the (Na⁺, Cl⁻)-(Na⁺, SO₄²⁻) pair are regressed from fitting experimental data on dissolution enthalpies and solubilities for the NaCl + Na₂SO₄ + H₂O ternary.     

Low-temperature heat capacities and standard molar enthalpy of formation of the complex

Low-temperature heat capacities of a solid complex Zn(Val)SO₄·H₂O(s) were measured by a precision automated adiabatic calorimeter over the temperature range between 78 and 373 K. The initial dehydration temperature of the coordination compound was determined to be, T _D=327.05 K, by analysis of the heat-capacity curve. The experimental values of molar heat capacities were fitted to a polynomial equation of heat capacities (C _p,m) with the reduced temperatures (x), [x=f (T)], by least square method. The polynomial fitted values of the molar heat capacities and fundamental thermodynamic functions of the complex relative to the standard reference temperature 298.15 K were given with the interval of 5 K. Enthalpies of dissolution of the [ZnSO₄·7H₂O(s)+Val(s)] (Δ_sol H _m,l ⁰) and the Zn(Val)SO₄·H₂O(s) (Δ_sol H _m,2 ⁰) in 100.00 mL of 2 mol dm^–3 HCl(aq) at T=298.15 K were determined to be, Δ_sol H _m,l ⁰=(94.588±0.025) kJ mol^–1 and Δ_sol H _m,2 ⁰=–(46.118±0.055) kJ mol^–1, by means of a homemade isoperibol solution–reaction calorimeter. The standard molar enthalpy of formation of the compound was determined as: Δ_f H _m ⁰ (Zn(Val)SO₄·H₂O(s), 298.15 K)=–(1850.97±1.92) kJ mol^–1, from the enthalpies of dissolution and other auxiliary thermodynamic data through a Hess thermochemical cycle. Furthermore, the reliability of the Hess thermochemical cycle was verified by comparing UV/Vis spectra and the refractive indexes of solution A (from dissolution of the [ZnSO₄·7H₂O(s)+Val(s)] mixture in 2 mol dm^–3 hydrochloric acid) and solution A’ (from dissolution of the complex Zn(Val)SO₄·H₂O(s) in 2 mol dm^–3 hydrochloric acid).     

Thermal modified Kaolinite as useful material for separation and preconcentration of trace amounts of manganese ions

This work assesses for the first time the potential of natural Kaolinite as adsorptive material for preconcentration of metal traces. Manganese is quantitatively retained by 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) on thermal modified Kaolinite by column method in pH range of 8.5-10.0 at flow rate of 2 ml min⁻¹. Manganese was removed from column with 5.0 ml of H₂SO₄ 4 mol l⁻¹ and determined by flame atomic absorption spectrometric at 279.5 nm. In this case, 0.l μg of manganese can be concentrated from 800 ml of aqueous sample (where concentration is as low as 0.125 μg l⁻¹). Detection limit is 4.3 μg l⁻¹ (3 δ_bl m⁻¹) and analytical curve is linear in the 0.02-10 mg l⁻¹ in final solution with correlation coefficient 0.9997 and relative standard deviation for eight replicate determination of 5 μg of manganese in final solution is 0.71%. The interference of a large number of anions and cations has been studied in detail to optimize the conditions and method was successfully applied for determination of manganese in complex materials.     

Oxidization of SO2 by Reactive Oxygen Species for Flue Gas Desulfurization and H2SO4 Production

A strong ionization dielectric barrier discharge was used to produce a high concentration of reactive oxygen species that were then injected into a simulated flue gas in a duct to remove SO₂ by oxidation. Sulfuric acid (H₂SO₄) was produced through the following two reactions: (1) O₃ oxidation of SO₂–SO₃, which then reacted with H₂O to produce H₂SO₄; and (2) reaction of O₂ ⁺ with H₂O to produce ·OH radicals, which then rapidly and non-selectively oxidized SO₂–H₂SO₄. When the molar ratio of reactive oxygen species to SO₂ was 4:1, the SO₂ removal efficiency was 94.6%, the energy consumption per cubic meter of flue gas was 13.3 Wh/m³, the concentration of recovered H₂SO₄ was 4.53 g/l, and the H₂SO₄ recovery efficiency was 28.8%. The H₂O volume fraction in the simulated flue gas affected the SO₂ removal efficiency, whereas the O₂ and CO₂ volume fractions did not. These results prove that oxidation by reactive oxygen species is a feasible method for flue gas desulfurization.     

Should acid ammonium oxalate replace hydroxylammonium chloride in step 2 of the revised BCR sequential extraction protocol for soil and sediment?

The revised, four-step BCR sequential extraction for soil or sediment has been compared with an alternative procedure in which 0.2 mol l⁻¹ ammonium oxalate (pH 3) replaced 0.5 mol l⁻¹ hydroxylammonium chloride (pH 1.5) in step 2, the reducible step. A variety of substrates were studied: BCR CRM601, a sewage sludge amended soil, two industrial soils, and a steel manufacturing by-product (basic oxygen furnace filter cake). Greater amounts of iron were recovered in step 2 when acid ammonium oxalate was used, for all substrates. Similar trends were observed for copper. Manganese and zinc were not strongly affected by the procedural modification, except for zinc in the two industrial soils, where oxalate extraction proved more efficient than use of hydroxylammonium chloride. A large proportion of the calcium and lead isolated in step 2 of the BCR procedure was not released until step 3 when the alternative procedure with oxalate in step 2 was used. This is probably due to rapid precipitation of analyte oxalates from solution. Thus, whilst oxalate offers superior dissolution of iron-containing matrix components, it should not be used if calcium or lead concentrations are to be measured. Selection of the most appropriated sequential extraction protocol for use in a particular study must always be carried out on the basis of “fitness for purpose” criteria. However, the revised BCR protocol, involving use of 0.5 mol l⁻¹ NH₂OH·HCl in the reducible step, appears to be more generally applicable than procedures involving acid ammonium oxalate.     

A theoretical study of the H2SO4+H2O → HSO4 −+H3O+ reaction at the surface of aqueous aerosols

The surface region of sulfate aerosols (supercooled aqueous concentrated sulfuric acid solutions) is the likely site of a number of important heterogeneous reactions in various locations in the atmosphere, but the surface region ionic composition is not known. As a first step in exploring this issue, the first acid ionization reaction for sulfuric acid, H₂SO₄ + H₂O HSO₄^– + H₃O⁺, is studied via electronic structure calculations at the Hartree–Fock level on an H₂SO₄ molecule embedded in the surface region of a cluster containing 33 water molecules. An initial H₂SO₄ configuration is selected which could produce H₃O⁺ readily available for heterogeneous reactions, but which involves reduced solvation and is consistent with no dangling OH bonds for H₂SO₄. It is found that at 0 K and with zero-point energy included, the proton transfer is endothermic by 3.4 kcal/mol. This result is discussed in the context of reactions on sulfate aerosol surfaces and, further, more complex calculations.Contribution to the Jacopo Tomasi Honorary Issue