Potentiometric determination of hydrogen peroxide at MnO2-doped carbon paste electrode

A novel hydrogen peroxide (H₂O₂) potentiometric sensor, made with a MnO₂-doped carbon paste electrode (CPE), is reported. Under optimum conditions, the electrode gives a Nernstian response for H₂O₂ in the concentration range 3.00×10⁻⁷–3.63×10⁻⁴ mol/l, with a slope of 21–19.4 mV/pH₂O₂ and a detection limit of 1.2×10⁻⁷mol/l H₂O₂. In addition, this sensor offers some analytical characteristics such as sensitivity, good reproducibility and a simple preparation procedure. The effects of both the components of the electrode and other conditions on the potential response of the sensor, as well as the possible response mechanism, are discussed.     

An electrochemiluminescent sensor for glucose employing a modified carbon nanotube paste electrode

A carbon nanotube paste (CNTP) electrode and a carbon nanotube paste/glucose oxidase (CNTP/GOx) electrode were prepared, and the electrochemiluminescent (ECL) behavior of luminol in the presence of glucose was investigated in detail at each of these electrodes. Compared to the classical carbon paste (CP) electrode, the CNTP electrode incorporating glucose oxidase greatly enhanced the response of the ECL sensor to glucose due to the electrocatalytic activity of the carbon nanotubes, the specificity of the enzymatic reaction, and the sensitivity of the luminol ECL reaction. Under optimal conditions, the electrode was found to respond linearly to glucose in the concentration range 1.0x10(-6) approximately 2.0x10(-3) mol/L, and the detection limit (defined as the concentration that can be detected at a signal-to-noise ratio of 3) was found to be a glucose concentration of 5.0x10(-7) mol/L. The method used to prepare the CNTP/GOx electrode was very convenient, and the electrode surface could be renewed in the case of fouling by simply polishing or cutting it to expose a new and fully active surface. The relative standard deviations (RSD) were found to be 6.8% and 8.9% for the CNTP electrode and the CNTP/GOx electrode (n=6). The electrode retained 95% of its initial response after two weeks.     

Mediated amperometric enzyme electrode incorporating peroxidase for the determination of hydrogen peroxide in organic solvents

An amperometric enzyme electrode incorporating horseradish peroxidase is described for the determination of hydrogen peroxide in organic solvents. The enzyme was co-adsorbed with an electron mediator, potassium hexacyanoferrate(II), on the surface of a graphite foil electrode, making reagentless measurement possible. The electrochemical reduction of the enzymatically oxidized mediator was utilized as the analytical signal. Studies in different solvent systems revealed that the electrode could be operated in dioxane, chloroform and chlorobenzene, the last two providing approximately double the sensitivity of the former. The presence of a small amount of aqueous buffer was essential for sensor activity. During 2 weeks of intermittent use, the sensitivity of the electrode decreased to 40% of its initial value. At least 50 assays could be performed with a single sensor.     

纳米碳管负载铂的修饰电极对H2O2的测定

采用嵌入修饰法制得了碳纳米管负载铂修饰的浸蜡石墨电极,结果发现该修饰电极对H2O2的氧化还原都有良好的电催化性能。但对H2O2的还原有更好的催化性能。H2O2的浓度在2.5×10-6~1×10-4mol/L范围内呈现良好的线性关系;检出限为1.26×10-6mol/L。     

An amperometric hydrogen peroxide biosensor based on immobilizing horseradish peroxidase to a nano-Au monolayer supported by sol-gel derived carbon ceramic electrode

A novel strategy for fabricating horseradish peroxidase (HRP)-based H(2)O(2) sensor has been developed by combining the merits of carbon sol-gel supporting matrix and nano-scaled particulate gold (nano-Au) mediator. The thiol functional group-derived carbon ceramic electrode (CCE) was first constructed using (3-mercaptopropyl) trimethoxy silane as sol-gel monomer. Then, the stable nano-Au monolayer was obtained through covalent linkage between nano-Au and thiol group on the surface of CCE. The experimental results showed that nano-Au monolayer formed not only could steadily immobilize HRP but also efficiently retain its bioactivity. Hydrogen peroxide was detected with the aid of hydroquinone mediator to transfer electrons between the electrode and HRP. The process parameters for the fabrication of the enzyme electrode and various experimental variables such as the operating potential, mediator concentration and pH of background electrolyte were explored for optimum analytical performance of the enzyme electrode. The biosensor had a fast response of less than 8 s with linear range of 1.22 x 10(-5) to 1.10 x 10(-3)mol l(-1) and a detection limit of 6.1 x 10(-6)mol l(-1). The sensitivity of the sensor for H(2)O(2) was 0.29 A l mol(-1) cm(-2). The activation energy for enzyme reaction was calculated to be 10.1 kJ mol(-1). The enzyme electrode retained 75% of its initial activity after 5 weeks storage in phosphate buffer at pH 7.     

Amperometric immunosensor for probing complement III (C3) based on immobilizing C3 antibody to a nano-Au monolayer supported by sol-gel-derived carbon ceramic electrode

An electrochemical immunosensor based on nano-size particulate gold (nano-Au) monolayer as sensing interface has been developed for probing complement III (C₃). The thiol functional group-derived carbon ceramic electrode (CCE) was firstly constructed using (3-mercaptopropyl) trimethoxy silane (MPTMOS) as sol-gel monomer. The stable nano-Au monolayer was obtained resulting from covalent combination between nano-Au and thiol group on the surface of CCE. The nano-Au monolayer formed was utilized as a sensing platform for the immobilization of C₃ antibody (anti-C₃) and subsequent immunoreaction. A competitive immunoassay format was adopted with horseradish peroxidase (HRP)-C₃ as a tracer, hydroquinone and hydrogen peroxide as the enzymatic substrates. The dynamic concentration range for C₃ is 0.08-5.6 μg ml⁻¹. The feasibility of regenerating nano-Au monolayer for consecutive assays was demonstrated by a simple chemical treatment after each determination. The high stability of formed nano-Au monolayer, readily adsorptive immobilization of antibody on nano-Au monolayer, efficient activity retention of loading immunoreactants as well as the simple operation for the formation of nano-Au monolayer make proposed methodology an attractive alternative for the designing new-type immunosensors.     

Simultaneous detection of cadmium, copper, and lead using a carbon paste electrode modified with carbamoylphosphonic acid self-assembled monolayer on mesoporous silica (SAMMS)

A new sensor was developed for simultaneous detection of cadmium (Cd²⁺), copper (Cu²⁺), and lead (Pb²⁺), based on the voltammetric response at a carbon paste electrode modified with carbamoylphosphonic acid (acetamide phosphonic acid) self-assembled monolayer (SAM) on mesoporous silica (Ac-Phos SAMMS). The adsorptive stripping voltammetry (AdSV) technique involves preconcentration of the metal ions onto Ac-Phos SAMMS under an open circuit, then electrolysis of the preconcentrated species, followed by a square wave potential sweep towards positive values. Factors affecting the preconcentration process were investigated. The voltammetric responses increased linearly with the preconcentration time from 1 to 30 min or with metal ion concentrations ranging from 10 to 200 ppb. The responses also evolved in the same fashion as adsorption isotherm in the pH range of 2-6. The metal detection limits were 10 ppb after 2 min preconcentration and improved to 0.5 ppb after 20 min preconcentration.     

Characterization of a carbon paste electrode modified with tripolyphosphate-modified kaolinite clay for the detection of lead

We report about the use of carbon paste electrode modified with kaolinite for analytical detection of trace lead(II) in domestic water by differential pulse voltammetry. Kaolinite clay was modified with tripolyphosphate (TPP) by impregnation method. The results show that TPP in kaolinite clay plays an important role in the accumulation process of Pb(II) on the modified electrode surface. The electroanalytical procedure for determination of Pb(II) comprised two steps: chemical accumulation of the analyte under open-circuit conditions, followed by electrochemical detection of the pre-concentrated species using differential pulse voltammetry. The analytical performance of this system has been explored by studying the effects of preconcentration time, carbon paste composition, pH, supporting electrolyte concentration, as well as interferences due to other ions. The calculated detection limit based on the variability of a blank solution (3s_b criterion) for 10 measurements was 8.4 × 10⁻⁸ mol L⁻¹, and the sensitivity determined from the slope of the calibration graph was 0.910 mol L⁻¹. The reproducibility (RSD) for five replicate measurements at 1.0 mg L⁻¹ lead level was 1.6%. The results indicate that this electrode is sensitive and effective for the determination of Pb²⁺.     

An amperometric hydrogen peroxide biosensor based on immobilization of horseradish peroxidase on an electrode modified with magnetic dextran microspheres

A new kind of magnetic dextran microsphere (MDMS) with uniform shape and narrow diameter distribution has been prepared from magnetic iron nanoparticles and dextran. Horseradish peroxidase (HRP) was successfully immobilized on the surface of an MDMS-modified glassy-carbon electrode (GCE), and the immobilized HRP displayed excellent electrocatalytic activity in the reduction of H₂O₂ in the presence of the mediator hydroquinone (HQ). The effects of experimental variables such as the concentration of HQ, solution pH, and the working potential were investigated for optimum analytical performance. This biosensor had a fast response to H₂O₂ of less than 10 s and an excellent linear relationship was obtained in the concentration range 0.20 μmol L⁻¹–0.68 mmol L⁻¹, with a detection limit of 0.078 μmol L⁻¹ (S/N = 3) under the optimum conditions. The response showed Michaelis–Menten behavior at larger H₂O₂ concentrations, and the apparent Michaelis–Menten constant was estimated to be 1.38 mmol L⁻¹. Moreover, the selectivity, stability, and reproducibility of the biosensor were evaluated, with satisfactory results. Figure Amperometric response of the biosensor to successive additions of H₂O₂ and the plot of amperometric response vs. H₂O₂ concentration     

Immobilized anthraquinone for redox mediation of horseradish peroxidase for hydrogen peroxide sensing

The detection of hydrogen peroxide is detailed using horseradish peroxidase and anthraquinone. Both species are immobilized on a glassy carbon electrode substrate. This dual immobilization gives rise to lower detection limits compared with the situation when either of the species is immobilized. Detection limits of 40 nM are reported within physiologically-relevant media.     

Ferrocene-mediated carbon paste electrode modified with d-fructose dehydrogenase for batch mode measurement of d-fructose

A mediated modified carbon paste and renewable surface electrode for fructose amperometric measurement based on d-fructose dehydrogenase (FDH) was prepared and optimized. Commercially available ferrocene (FcH) and hydroxymethyl ferrocene (FcCH₂OH) were used as mediators. The substituted FcH showed better linearity and higher sensitivity. The influence of different experimental parameters was studied for optimum analytical performance. The final FDH-modified electrode showed good analytical performance for batch mode measurements of fructose.     

Biosensor for determination of hydrogen peroxide based on catalase activity of human erythrocytes

A hydrogen peroxide biosensor based on human erythrocytes is described. Erythrocytes are retained on the surface of an oxygen electrode by a semipermeable membrane. The response is based on the catalase activity of the erythrocytes. The sensitivity of 10^?4 mol 1^?1 and linearity from 1.5×10^?4 to 5×10^?3 mol^?1 are comparable to those of analogous enzyme biosensors for hydrogen peroxide determination. The greatest advantages of this biosensor are its easy preparation and a lifetime of 2 months together with good reproducibility (relative standard deviation <5%) and selectivity; only ascorbic acid appeared to interfere with the measurements.     

Amperometric biosensor for hydrogen peroxide based on coimmobilized horseradish peroxidase and methylene green in ormosils matrix with multiwalled carbon nanotubes

A novel amperometric biosensor for the analytical determination of hydrogen peroxide was developed. The fabrication of the biosensor was based on the coimmobilization of horseradish peroxidase (HRP), methylene green (MG) and multiwalled carbon nanotubes within ormosils; 3-aminopropyltrimethoxysilane (APTMOS), 2-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (ETMOS) and phenyltrimethoxysilane (PHTMOS). APTMOS determined the hydrophilicity/hydrophobicity of the ormosils and PHTMOS and ETMOS increased the physical and mechanical strength of the ormosil matrix. The ormosil modified electrodes were characterized with SEM, UV-vis spectroscopy and electrochemical methods. Cyclic voltammetry and amperometric measurements demonstrated the MG coimmobilized with HRP in this way, displayed good stability and could efficiently shuttle electrons between immobilized enzyme and electrode, and MWCNTs facilitated the electrocatalytic reduction of H₂O₂ at reduced over potential. The Micheaelis constant of the immobilized HRP was 1.8 mM, indicating a high affinity of the HRP to H₂O₂ without loss of enzymatic activity in ormosil matrix. The prepared biosensor had a fast response of H₂O₂, less than 10 s, and excellent linear range of concentration from 5 × 10⁻⁷ to 2 × 10⁻⁵ M with the detection limit of 0.5 μM (S/N = 3) under the optimum conditions. At the same time, the influence of solution pH, effect of enzyme amount, steady-state applied potential and temperature on the biosensor were investigated. The enzyme electrode retained about 90% of its initial activity after 30 days of storage in a dry state at 4 °C. The preparation of the developed biosensor was convenient and showed high sensitivity with good stability.     

A new electrochemiluminescent detection system equipped with an electrically heated carbon paste electrode for CE

An electrochemiluminescent (ECL) detection system in CE with an electrically heated carbon paste electrode (CPE) was developed. This CPE could be heated by a 100 kHz alternating current (ac) generated from a function generator, and the temperature of the electrode (Te) could be controlled. To evaluate the feasibility and reliability of this system, the electrochemically generated Ru(bpy)(3) (3+)-based ECL reaction was used for detection of triethylamine (TEA) and tri-n-propylamine (TPrA). Ru(bpy)(3) (2+) was added into the separation buffer solution with precolumn mode. Effects of several important factors were investigated to acquire the optimum conditions. Under the optimum conditions, the heated electrode has been shown to provide advantages by the measurement of ECL intensity in CE at elevated Te. Compared with the conventional electrode at the room temperature, using heated CPE could improve peak shape and gain good reproducibility with lower detection limits and wider linearity ranges. Compared with the room temperature, the linear ranges and detection limits (S/N = 3) for TEA and TPrA were improved about one magnitude when the Te was 39 degrees C. In contrast, the RSD was lower than for the electrode at room temperature.     

Voltammetric study of 2-methyl-4,6-dinitrophenol at a modified carbon paste electrode

The voltammetric behavior of 2-methyl-4,6-dinitrophenol at a modified carbon paste electrode has been studied. Among the modifiers tested, hidepowder was found to give the best results. Cyclic voltammetry and differential pulse voltammetry were used to study the nature of the reaction; the possibility of accumulation of the analyte onto the electrode was studied by differential pulse voltammetry. An irreversible behavior and the adsorption of 2-methyl-4,6-dinitrophenol on the electrode were confirmed. The reduction signal shows two peaks. A linear relationship between the first peak height and the concentration of 2-methyl-4,6-dinitrophenol was obtained in the range 0.001–5 mg l⁻¹, with a detection limit of 3.2 μg l⁻¹ and a relative standard deviation of 3.20%. The interferences with the reduction peak of 2-methyl-4,6-dinitrophenol of several nitro- and chloro-phenols and inorganic species were tested.     

Electrochemical behavior and detection of guanine using a sodium montmorillonite-modified carbon paste electrode

Herein, a sodium montmorillonite-modified carbon paste electrode is described for the electrochemical determination of guanine. Guanine yields a well-defined and very sensitive oxidation peak at the sodium montmorillonite-modified carbon paste electrode. Compared with the unmodified carbon paste electrode, the modified electrode facilitates the electron transfer of guanine, since it notably increases the oxidation peak current and lowers the oxidation overpotential of guanine. Based on this, a simple sensitive reliable electrochemical method is proposed for the detection of guanine after all the experimental parameters, such as solution pH value, sodium montmorillonite content in the carbon paste electrode, accumulation potential, and time, are optimized. Under the optimized conditions, the oxidation peak current of guanine varies linearly with its concentration in the range 5.0×10⁻⁸ to 2.0×10⁻⁵ M and the detection limit (signal-to-noise=3) is 2.0×10⁻⁸ M after 4-min accumulation. This method is successfully demonstrated with urine samples. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 2, pp. 178–182. The text was submitted by the authors in English.     

A study on the determination of chromium as chromate at a carbon paste electrode modified with surfactants

A procedure for the determination of chromium is described based on synergistic pre-concentration of the chromate anion at a carbon paste electrode modified in situ with quarternary ammonium salts such as 1-ethoxycarbonylpentadecyltrimethylammonium bromide (Septonex^®), cetyltrimethylammonium bromide (CTAB) or cetylpyridinium bromide (CPB). The proper electrochemical detection utilises the reduction Cr(VI) → Cr(III) performed in the differential pulse cathodic voltammetric mode. In discussion, considerable attention has been paid to the accumulation mechanism at the carbon paste electrode in the presence of surfactants. Furthermore, after optimising the corresponding experimental conditions (0.1-0.3 M HCl + 0.1 M NaCl as the supporting electrolyte, 2.5-25 μM as the total concentration of modifier, pre-concentration at +0.7 V versus Ag/AgCl and the stripping from +0.7 to −0.4 V), the analytical performance of the method has been evaluated. The signal of interest was reproducible within ±8% and proportional to the concentration in a range of 0.5-50 μM CrO₄²⁻, with a limit of detection (S/N = 3:1) of about 5×10⁻⁸ M CrO₄²⁻ (with accumulation for 300 s). Interference studies were focused mainly on the species capable of forming ion-pairs with the modifier; i.e., TlCl₄⁻, AuCl₄⁻, PdCl₄²⁻, PtCl₆²⁻, VO₄³⁻, MnO₄⁻ and I⁻. Practical applicability of the method was tested on model solutions via the recovery rates (typically 90-110%) or using selected certified reference materials (tea, bush leaves, clover) and two samples of black tea when the respective results were compared to those obtained by the reference determinations with ICP-AES.     

Dendrimer-rhodium nanoparticle modified glassy carbon electrode for amperometric detection of hydrogen peroxide

Metallic nanoparticles of rhodium were prepared by using the newly synthesized N,N-bis-succinamide-based dendrimer as stabilizers. The Rh nanoparticles were spherical shaped with a particle size of ∼2 nm. The dendrimer Rh-encapsulated nanoparticles (Rh-DENs) were immobilized on glassy carbon electrode (GCE) and their electrocatalytic activity towards hydrogen peroxide reduction was investigated using cyclic voltammetry and chronoamperometry. The Rh-DENs modified GCE showed excellent electrocatalytic activity for hydrogen peroxide reduction reactions. The steady-state cathodic current response of the modified electrode at −0.3 V (vs SCE) in phosphate buffer (pH 7.0) showed a linear response to hydrogen peroxide concentration ranging from 8 to 30 μM with a detection limit and sensitivity of 5 μM and 0.03103 × 10⁻⁶ A μM⁻¹, respectively.     

Modified carbon paste electrode for the electrochemical sensing of 3,5,6-trichloro-2-pyridinol

An electrochemical sensor for the determination of 3,5,6-trichloro-2-pyridinol (TCP), the main metabolite of the pesticide chlorpyrifos, was herein developed. TCP has greater solubility than the source pesticide, and its occurrence in ground and surface water is more frequent and more dangerous. The sensor was fabricated using carbon paste modified with the inorganic complex chloro-5,10,15,20-tetrakis-(pentafluorophenyl)-21 H,23 H-porphyrin iron(III) (FeTPPCl); this metallic complex has a chemical core structure similar to the heme cofactor of the cytochrome P450 (CYPs). Measurements were performed with square-wave voltammetry. Using the optimised voltammetric parameters and without any sample preparation, the sensor showed a limit of detection of 2.8 mg L^?1 (14 μmol L^?1), recoveries ca. 102%, suitable selectivity and long durability (over 1 month).     

Improving the detection of hydrogen peroxide of screen-printed carbon paste electrodes by modifying with nonionic surfactants

Nonionic surfactants, such as Triton X-100 and Tween-20, were shown in this study to improve the electrocatalytic activity of screen-printed carbon paste electrodes (SPCE). The electrochemical response of SPCE to hydrogen peroxide increased 8-10-fold with the modification of nonionic surfactants. In addition, the glucose biosensors fabricated from nonionic surfactant-modified SPCE exhibited 6.4-8.6-fold higher response to glucose than that fabricated from unmodified SPCE. A concentration effect is proposed for nonionic surfactant to bring neutral reactants to the surface of electrode. Moreover, nonionic surfactant-modified SPCE exhibits a capability of repetitive usage and good reproducibility (R.S.D. < 5%) in the measurement of H₂O₂. Interestingly, the nonionic surfactant-modified SPCE exhibited an opposite effect to ascorbic acid, a common electroactive agent, which causes interference during clinical diagnosis. The differential responses of nonionic surfactant-modified SPCE to H₂O₂ and ascorbic acid suggest its potential in the development of biosensors for clinical diagnosis.