Simplified liquid-chromatographic determination of residues of tetracycline antibiotics in eggs

Summary A high-performance liquid chromatographic (HPLC) procedure is described for the identification and quantification of residues of tetracycline antibiotics (TCA) (oxytetracycline, tetracycline, chlortetracycline, and doxycycline), in eggs. Spiked and blank samples were prepared by homogenization with 1∶1 (v/v) acetonitrile-mixed Mcllvaine buffer and EDTA solution (pH 4.0) then centrifugal ultrafiltration. HPLC was performed on a reversed-phase column with acetonitrile-5% (v/v) aqueous acetic acid, 35∶65 (v/v), as mobile phase and photo-diode array detection. Average recoveries (each drug spiked at 0.1, 0.2, 0.3, 0.5 and 1.0 μg g⁻¹) were >-77% with standard deviations (SD) between 1.5 and 3.5%. The inter-assay variabilities and theirSD were <3.4% and <0.7%, respectively, and intra-assay variability was between 2.0 and 3.9%. The limits of quantitation (LOQ) were 0.064 0.087, 0.121, and 0.131 μg g⁻¹ for OTC, TC, CTC, and DC, respectively. The total time required for the analysis of one sample was less than 30 min.     

Simultaneous determination of zirconium and hafnium as ternary complexes with 5-Br-PADAP and fluoride using solid-phase extraction and reversed-phase liquid chromatography

Solid-phase extraction (SPE) along with reversed-phase liquid chromatography (RP-LC) was used for the simultaneous determination of Zr(IV) and Hf(IV) by means of their ternary chelates with fluoride and 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP). The conditions of SPE sorption were examined in detail: type of SPE column, volume of the sample, volume of the eluent, concentrations of metal ions, fluoride salt, chromogenic reagent, organic phase, and pH. It was established that the sorption of Zr(IV) and Hf(IV), as their ternary chelates, on SPE Zorbax SPE C18 (EC) cartridge was the most efficient, when the sample containing metal ion (Zr(IV), Hf(IV), both, up to 2 μg), 5-Br-PADAP 1.5×10⁻⁴, NaF 7.5×10⁻⁵ mol l⁻¹, methanol 40%, pH 4.5±1 was applied for the SPE sorption. The chelates were discarded from SPE cartridge using acetonitrile/water (99.75+0.25, v/v) eluent containing 3.8×10⁻⁴ mol l⁻¹ sodium fluoride and subsequently separated by RP-LC method. The RP-LC separation of both chelates was optimized and Zorbax SB-C18 analytical LC column along with acetonitrile/water (65+35, v/v) eluent containing the 1.5×10⁻⁴ mol l⁻¹ sodium fluoride was used. The established SPE/LC conditions allow Zr(IV) 0.08-2.0 μg and Hf(IV) 0.04-2.0 μg determination in a sample volume up to 150 ml. The detection limits, 0.03 μg Hf(IV) and 0.05 μg Zr(IV), were obtained. Recoveries, (94±2)% for Hf(IV) chelate and (106±2)% for Zr(IV) chelate were obtained, when 1 μg of Zr(IV) and Hf(IV) ions were determined by the present SPE/LC method from the sample volume of 100 ml. The established, pre-concentration SPE conditions, along with the LC separation and determination allow the assay of Zr(IV) and Hf(IV) in complicated matrix materials. The present SPE/LC method was applied to the determination of Zr(IV) and Hf(IV) in tap water and reference geological material (rock, NCS DC 73303; certified content: Zr, 27.7×10⁻³% (w/w) and Hf, 6.5×10⁻⁴% (w/w)).     

Determination of Abamectin Residues in Avocados by Microwave-Assisted Extraction and HPLC with Fluorescence Detection

In this article a new analytical method for the confirmation and quantification of abamectin residues in avocados is described. The method allows a fast analysis of abamectin homologues using microwave assisted extraction (MAE), solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence (FL) detection using trifluoroacetic anhydride (TFAA) and N-methylimidazole (NMIM) as derivatizing agents. The mobile phase consisted of water, methanol and acetonitrile (5:47.5:47.5 v/v/v) and was pumped at a rate of 1.1 mL min⁻¹ (isocratic elution). Homogenized avocado samples were extracted once with 20 mL acetonitrile:water 4:1 (v/v) in a microwave oven for 26 min at 700 W with a maximum temperature of 80 °C. MAE operational parameters were optimized by means of an experimental design. Extracts were cleaned using C₁₈ SPE cartridges. Average recoveries of the method at four spiked levels (0.005, 0.01, 0.10 and 1.0 mg kg⁻¹) were found to be in the range 90–100% with good precision (RSD < 12%). The limits of detection (LODs) and quantification (LOQs) of the whole method were 0.001 and 0.003 mg kg⁻¹, respectively, which are lower than the maximum residue limit (MRL) established by the Spanish and the European legislation in avocados (0.01 mg kg⁻¹). Several avocado samples previously treated with the pesticide were also analyzed.     

Determination of pesticides fenoxycarb and permethrin by sequential injection chromatography using miniaturized monolithic column

Sequential injection chromatography system equipped with miniaturized 10 mm monolithic column was used for fast simultaneous determination of two pesticides—fenoxycarb (FC) and permethrin (PM). The system was composed of a commercial sequential injection analysis (SIA) system (FIAlab^® 3000, 6-port selection valve and 5.0 mL syringe pump), commercially available column Chromolith™ RP-18e (10 mm × 4.6 mm i.d.) (Merck^®, Germany) and CCD UV-vis detector (USB 2000, Ocean-optics) with 1.0 cm Z-flow cell, absorbance was monitored at 225 nm. The mobile phase used for analysis was acetonitrile/water (60:40, v/v), flow rates were 0.6 mL min⁻¹ for elution of fenoxycarb and 1.2 mL min⁻¹ for elution of permethrin. For each analysis 4.8 mL of mobile phase was used. The chromatographic resolution between both compounds was >8 and analysis time was <6.5 min under the optimal conditions. Limits of detection were determined at 2.0 μg mL⁻¹ for fenoxycarb and 1.0 μg mL⁻¹ for permethrin. Samples were prepared by diluting with mobile phase and injected volume was 10 μL for each analysis. Developed method was applied to analysis of both pesticides in veterinary pharmaceutical foams and sprays ARPALIT^® Neo (Aveflor, Czech Republic). SIC method was compared with validated method (HPLC, reverse phase 100 mm monolithic column, gradient elution).     

Determination of momordicoside A in bitter melon by high-performance liquid chromatography after solid-phase extraction

Summary Momordicoside A has been determined by solid-phase extraction (SPE) on a Envi Carb cartridge (3 mL, 250mg) then high-performance liquid chromatography (HPLC) on a C₁₈ column (4.6 mm×250 mm, 5 μm particle) with acetonitrile-methanol-50mm potassium dihydrogen phosphate buffer, 25:20:60 (v/v), as mobile phase, at a flow rate of 0.8 mL min⁻¹, and UV detection at 208 nm. The analytical method was shown to be highly reproducible, with precision (asRSD) and accuracy (asRME)<10%, both intra-day and inter-day. Absolute recoveries were >90%. The method was applied to the determination of momordicoside A in various tissues from different varieties of bitter melon from different producing areas.     

Optimization of antibiotic analysis in water by solid-phase extraction and high performance liquid chromatography–mass spectrometry/mass spectrometry

This paper describes the development of an optimized method based on solid-phase extraction (SPE) followed by liquid chromatography–electrospray ionization tandem mass spectrometry (LC–MS/MS) for the simultaneous analysis of ten antibiotic compounds including tetracyclines, sulfonamides, macrolides and quinolones. LC–MS/MS sensitivity has been optimized by alterations to both LC and MS operations. Of the two high resolution columns tested, Waters Symmetry C₁₈ endcapped and Agilent Zorbax Bonus-RP, the latter was found to show better performance in producing sharp peaks and clear separation for most of the target compounds. Optimization of the MS fragmentation collision and cone energy enhanced the peak areas of the target analytes. The recovery of the target compounds from water samples was most efficient on Waters Oasis HLB SPE cartridge, while methanol was shown to be the most suitable solvent for desorbing the compounds from SPE. In addition, acidification of samples prior to SPE was shown to enhance the recovery of the compounds. To ensure a satisfactory recovery, the flow rate through SPE should be maintained at ≤10 mL min⁻¹. The method was successfully applied to the analysis of antibiotics from environmental water samples, with concentrations being <LOD in tap water, between <LOD to 28 ng L⁻¹ in river water and between <LOD to 230 ng L⁻¹ in sewage effluent.     

Using on-line solid phase extraction for flow-injection spectrophotometric determination of salbutamol

In the proposed procedure, the determination of salbutamol with Folin-Ciocalteau reagent (FC) using a flow injection analysis technique (FIA) with spectrophotometric detection at 750 nm is described. The lab-made FIA system consisted of a peristaltic pump Gilson Minipulse 3 equipped with Tygon tubes, double 6-port external Vici Valco sample injector and S 2000/SAD500 fiber optic spectrophotometer. It was controlled by a PC with use of originally compiled LabVIEW^®—supported software containing the mathematical library with various statistical functions for off-line data evaluation. Concentration, volume of reagents and flow rate were optimised by a simplex method. The proposed system was used for the direct determination of salbutamol sulphate in the tablets and the human urine without preliminary pre-treatment of the sample. The negative effect of interfering substances (excipients of the tablets and matrix of the urine) is overcome by a solid phase extraction (SPE), when salbutamol is adsorbed on the solid phase in the microcolumn, which is integrated directly into the flow system. Pre-treatment of the sample takes place directly in the flowing stream. The sample throughput without carryover of on-line SPE was 60-80 samples per hour. With the SPE column (Baker—carboxylic acid), salbutamol was determined in the linear range from 1 to 15 μg ml⁻¹ (R.S.D.=1.2%), with detection limit (3σ) 0.1 μg ml⁻¹ and a frequency of 40-60 samples per hour in the water solutions. The salbutamol was determined in the linear range from 2 to 20 μg ml⁻¹ (R.S.D.=1.7%), with detection limit (3σ) 1 μg ml⁻¹ and a frequency of 30 samples per hour in the samples of the human urine.     

Rapid high-performance liquid chromatographic determining technique of sulfamonomethoxine, sulfadimethoxine, and sulfaquinoxaline in eggs without use of organic solvents

A determining technique of sulfonamides (SAs) (sulfamonomethoxine (SMM), sulfadimethoxine (SDM), and sulfaquinoxaline (SQ)) in eggs, without use of organic solvents, is developed utilizing a high-performance liquid chromatography (HPLC) interfaced with a photo-diode array detector. The sample preparation was performed by homogenizing with perchloric acid solution using a handy ultrasonic-homogenizer followed by a centrifugal ultra-filtration unit. An analytical column and an isocratic mobile phase for HPLC are a reversed-phase C₄ column ( mm i.d.) and 0.18 mol l⁻¹ citric acid solution, respectively. The proposed technique was shown to be linear (r>0.998) over the concentration range 0.1-2.0 μg g⁻¹. Average recoveries of three SAs (spiked 0.05, 0.1, 0.15, and 0.2 μg g⁻¹) ranged from 80.3 to 88.4%, with relative standard deviations (R.S.D.s) between 3.4 and 5.8%. The practical detection limits and total time required for the analysis of one sample were < 0.05 μg g⁻¹ and <30 min, respectively. In all the processes, no organic solvents were used at all.     

A novel application of Onyx™ monolithic column for simultaneous determination of salicylic acid and triamcinolone acetonide by sequential injection chromatography

A novel and fast simultaneous determination of triamcinolone acetonide (TCA) and salicylic acid (SA) in topical pharmaceutical formulations by sequential injection chromatography (SIC) as an alternative to classical high performance liquid chromatography (HPLC) has been developed. A recently introduced Onyx™ monolithic C18 (50 mm × 4.6 mm, Phenomenex^®) with 5 mm monolithic precolumn were used for the first time for creating sequential injection chromatography system based on a FIAlab^® 3000 with a six-port selection valve and 5.0 mL syringe pump in study. The mobile phase used was acetonitrile/water (35:65, v/v), pH 3.3 adjusted with acetic acid at flow rate 0.9 mL min⁻¹. UV detection provided by fibre-optic DAD detector was set up at 240 nm. Propylparaben was chosen as suitable internal standard (IS). There is only simple pre-adjustment of the sample of topical solution (dilution with mobile phase) so the analysis is not uselessly elongated. Parameters of the method showed good linearity in wide range, correlation coefficient >0.999; system precision (relative standard deviation, R.S.D.) in the range 0.45-1.95% at three different concentration levels, detection limits (3σ) 1.00 μg mL⁻¹ (salicylic acid), 0.66 μg mL⁻¹ (triamcinolone acetonide) and 0.33 μg mL⁻¹ (propylparaben) and recovery from the pharmaceutical preparations in the range 97.50-98.94%. The chromatographic resolution between peaks of compounds was more than 4.5 and analysis time was 5.1 min under the optimal conditions. The advantages of sequential injection chromatography against classical HPLC are discussed and showing that SIC can be a method of option in many cases.     

Improved methods for urinary atrazine mercapturate analysis--assessment of an enzyme-linked immunosorbent assay (ELISA) and a novel liquid chromatography-mass spectrometry (LC-MS) method utilizing online solid phase extraction (SPE)

Elimination of interfering substances in urine by solid phase extraction (SPE) prior to analysis resulted in 10-fold improvement in the sensitivity of atrazine mercapturate (AM) enzyme-linked immunosorbent assay (ELISA) compared to previous reports. Of the two tested SPE systems, Oasis^® HLB and MCX, the mixed-mode MCX gave good recoveries (82%) of AM in spiked samples measured by ELISA, whereas the reverse-phase HLB phase was not compatible with the immunochemical method. At relatively high concentrations of urinary AM (>20 ng mL⁻¹), sample dilution was effective enough for the elimination of interfering substances. The new liquid chromatography-mass spectrometry (LC-MS) method developed for AM utilizes online-SPE with Oasis^® HLB, column switching and a stable-isotope internal standard. The limit of quantification (0.05 ng mL⁻¹) indicates improved sensitivity compared with most previously published LC-MS methods for AM. Validation of all three methods, LC-MS, ELISA + SPE and ELISA + dilution with spiked urine samples showed good correlation between the known and measured concentrations with R² values of 0.996, 0.957 and 0.961, respectively. When a set (n = 70 plus 12 blind duplicates) of urine samples from farmers exposed to atrazine was analyzed, there was a good agreement (R² = 0.917) between the log normalized data obtained by ELISA + SPE and LC-MS. High correlation among the data obtained by the two tested methods and the LC-MS method by the Center of Disease Control and Prevention (CDC), together with low variability among the blind duplicates, suggests that both methods reported here would be suitable for the analysis of urinary AM as a biomarker for human exposure of atrazine.     

Trace analysis of tetracycline antibiotics in human urine using UPLC–QToF mass spectrometry

A rapid, sensitive and specific ultra-performance liquid chromatography–quadrupole time-of-flight mass spectrometry (UPLC–QToF-MS) method has been developed and validated for simultaneous determination of three tetracyclines (TCs) including oxytetracycline, tetracycline, and chlortetracycline in human urine. Human urine sample preparation involves pH adjustment to 4 with hydrochloric acid, pre-concentration, and cleanup by solid phase extraction (SPE) process. The chromatographic separation of all TCs was achieved in less than 5 min using UPLC and ESI-QToF-MS was successfully employed for the identification and quantification. The accurate masses of the product ions were calculated using lock mass correction, and were deviated from the theoretical masses by 0.5–1.9 mDa and 1.1–4.5 ppm, respectively. The developed method was validated in terms of linearity, sensitivity, selectivity, decision limit, detection capability, accuracy, and precision. Limit of detection and limit of quantitation for all TCs were estimated in the range of 0.089–0.138 ng mL^{− 1} and 0.294–0.455 ng mL^{− 1}, respectively. High overall recoveries of greater than 90% were achieved with linear responses over the 0.5–2 ng mL^{− 1} range for all TCs in urine samples.     

Fast simultaneous spectrophotometric determination of naphazoline nitrate and methylparaben by sequential injection chromatography

Fast simultaneous determination of naphazoline nitrate and methylparaben in pharmaceuticals using separation method based on a novel reversed-phase sequential injection chromatography (SIC) is described in this contribution as an alternative to classical HPLC. A Chromolith™ Flash RP-18e (25 mm × 4.6 mm) column (Merck^®, Germany) and a FIAlab^® 3000 system (USA) with a six-port selection valve and 5.0 ml syringe pump were used for sequential injection chromatographic separations in our study. The mobile phase used was methanol/water (40:65, v/v), pH 5.2 adjusted with triethylamine 0.8 μl ml⁻¹ and acetic acid, at flow rate 0.9 ml min⁻¹. UV detection provided by DAD detector and two wavelengths were simultaneously monitored for increasing sensitivity of determination. Detector was set up at 220 nm for naphazoline nitrate and 256 nm for methylparaben and ethylparaben (IS). There is no necessity to use pre-adjustment of sample of nasal drops (only dilution with mobile phase) so the time of the whole analysis is very short. The validation parameters have shown good results: linearity of determination for both components (naphazoline nitrate and methylparaben), correlation coefficient >0.999; repeatability of determination (R.S.D.) in the range 0.5-1.6% at three different concentration levels, detection limits 0.02 μg ml⁻¹ (naphazoline nitrate) and 0.20 μg ml⁻¹ (methylparaben and ethylparaben), and recovery from the pharmaceutical preparations in the range 100.06-102.55%. The chromatographic resolution between peaks of compounds was more than 4.0 and analysis time was less than 4 min under the optimal conditions. The advantages and drawbacks of SIC against classical HPLC are discussed showing that SIC can be an advantageous alternative in many cases.     

Enhanced capabilities of separation in Sequential Injection Chromatography--fused-core particle column and its comparison with narrow-bore monolithic column

In the Sequential Injection Chromatography (SIC) only monolithic columns for chromatographic separations have been used so far. This article presents the first use of fused-core particle packed column in an attempt to extend of the chromatographic capabilities of the SIC system. A new fused-core particle column (2.7 μm) Ascentis^® Express C18 (Supelco™ Analytical) 30 mm × 4.6 mm brings high separation efficiency within flow rates and pressures comparable to monolithic column Chromolith^® Performance RP-18e 100-3 (Merck^®) 100 mm × 3 mm. Both columns matches the conditions of the commercially produced SIC system - SIChrom™ (8-port high-pressure selection valve and medium-pressure Sapphire™ syringe pump with 4 mL reservoir - maximal work pressure 1000 PSI) (FIAlab^®, USA). The system was tested by the separation of four estrogens with similar structure and an internal standard - ethylparaben. The mobile phase composed of acetonitrile/water (40/60 (v/v)) was pumped isocratic at flow rate 0.48 mL min⁻¹. Spectrophotometric detection was performed at wavelength of 225 nm and injected volume of sample solutions was 10 μL. The chromatographic characteristics of both columns were compared. Obtained results and conclusions have shown that both fused-core particle column and longer narrow shaped monolithic column bring benefits into the SIC method.     

A practical method for sensitive determination of the fluorescent water-tracer uranine by reversed phase HPLC under alkaline conditions

A stable and highly sensitive HPLC method for uranine has been developed. Because of unstableness of silica-based octadecyl-C18 columns at high pH condition, a reversed phase HPLC analysis under alkaline conditions has not necessarily taken as a usual method. However, the application for uranine seems to be advantageous, since the fluorescence yield of uranine is markedly enhanced at high pH condition. The detection limit of the HPLC system was 0.9 pg. The analytical consideration was also paid for the solid phase extraction (SPE) prior to the HPLC analysis with careful consideration of the recently revised pK_a values of uranine. The recovery rate of uranine by SPE was found to depend on the sample volume and a few ml of seawater was applied to SPE in order to maintain the recovery rate during SPE. A combination of HPLC and SPE methods achieved detection of uranine at concentrations as low as 0.2 ng l⁻¹ (0.5 pM), which was comparable to the background concentration of uranine in coastal water off Japan. For the practical use of the detected tracer-uranine concentration values after substantial duration after release, the photodegradation of uranine in surface water was also evaluated in terms of incident solar radiation dose as an exponential rate constant of −0.135 mol photon⁻¹ m².     

Solid-phase/supercritical-fluid extraction for liquid chromatography of phenolic compounds in freshwater microalgae and selected cyanobacterial species

In the present paper a new extraction technique based on the combination of solid-phase/supercritical-fluid extraction (SPE/SFE) with subsequent reversed-phase HPLC is described. The SPE/SFE extractor was originally constructed from SPE-cartridge incorporated into the SFE extraction cell. Selected groups of benzoic acid derivatives (p-hydroxybenzoic, protocatechuic, gallic, vanillic and syringic acid), hydroxybenzaldehydes (4-hydroxybenzaldehyde and 3,4-dihydroxybenzaldehyde) and cinnamic acid derivatives (o-coumaric, p-coumaric, caffeic, ferulic, sinapic and chlorogenic acid) were extracted. Cyclic addition of binary extraction solvent system based on methanol:water (1:1, v/v) and methanol/ammonia aqueous solution was used for extraction at 40 MPa and 80 °C. The p-hydroxybenzoic, protocatechuic, vanillic, syringic, caffeic and chlorogenic acid; 4-hydroxybenzaldehyde and 3,4-dihydroxybenzaldehyde were identified by HPLC-electrospray mass spectrometry in SPE/SFE extracts of acid hydrolyzates of microalga (Spongiochloris spongiosa) and cyanobacterial strains (Spirulina platensis, Anabaena doliolum, Nostoc sp., and Cylindrospermum sp.). For the identification and quantification of the compounds the quasi-molecular ions [M−H]⁻ and specific fragments were analysed by quadrupole mass spectrometry analyzer. Our analysis showed that the microalgae and cyanobacteria usually contained phenolic acids or aldehydes at μg levels per gram of lyophilized sample. The proposed SPE/SFE extraction method would be useful for the analysis of different plant species containing trace amount of polar fraction of phenols.     

SPE then RP-LC for Simultaneous Analysis of Cyromazine and its Metabolite Melamine in Liquid Milk and Egg

Solid-phase extraction (SPE) and reversed-phase liquid chromatography (RP-LC) have been used for simple, sensitive simultaneous analysis of cyromazine and melamine residues in liquid milk and eggs. The conditions used for SPE and LC were investigated and optimized. A combined cation-exchange–reversed-phase cartridge was used for clean-up, and an ODS (C₁₈) column (150 mm × 4.6 mm i.d., 5-μm particles) with 62:38 (v/v) 5 mm sodium lauryl sulfate (pH 3.4)–acetonitrile as mobile phase was used for RP-LC. Under the optimum conditions the method limit of detection (LOD) for both cyromazine and melamine was 6.2 μg kg⁻¹ for liquid milk samples, and 11.5 μg kg⁻¹ for egg samples. Average recovery of cyromazine and melamine from milk samples was 90.3%, RSD 4.6–5.6%, and 99.6%, RSD 3.2–4.7%, respectively. Average recovery of cyromazine and melamine from egg samples was 85.3%, RSD 1.0–4.7%, and 89.6%, RSD 3.1–5.0%, respectively. The method enables detection of melamine and cyromazine at levels as low as 20.7 μg kg⁻¹ in liquid milk and 38.3 μg kg⁻¹ in egg.

     

Simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N(4)-acetyl metabolites with gradient liquid chromatography in chicken plasma, tissues, and eggs

A simultaneous determination of sulfamonomethoxine, sulfadimethoxine, and their hydroxy/N⁴-acetyl metabolites in chicken plasma, muscle, liver, and eggs using gradient high-performance liquid chromatography (HPLC) with a photo-diode array detector is developed. All the compounds are extracted by a handheld ultrasonic homogenizer with ethanol followed by centrifugation. The separation is performed by a reversed-phase C4 column with a gradient elution (ethanol:1% (v/v) acetic acid, v/v; 10:90 → 20:80). Average recoveries from samples spiked at 0.1-1.0 μg g⁻¹ or μg ml⁻¹ for each drug were >90% with relative standard deviations within 4%. The limits of quantitation were <30 ng g⁻¹ or ng ml⁻¹.     

Magnetically assisted solid phase extraction using Fe3O4 nanoparticles combined with enhanced spectrofluorimetric detection for aflatoxin M1 determination in milk samples

A novel, facile and inexpensive solid phase extraction (SPE) method using ethylene glycol bis-mercaptoacetate modified 3-(trimethoxysilyl)-1-propanethiol grafted Fe₃O₄ nanoparticles coupled with spectrofluorimetric detection was proposed for determination of aflatoxin M1 (AFM1) in liquid milk samples. The method uses the advantage fluorescence enhancement by β-cyclodexterin complexation of AFM1 in 12% (v/v) acetonitrile–water and the remarkable properties of Fe₃O₄ nanoparticles namely high surface area and strong magnetization were utilized to achieve high enrichment factor (57) and satisfactory extraction recoveries (91–102%) using only 100 mg of magnetic adsorbent. Furthermore, fast separation time of about 15 min avoids many time-consuming column-passing procedures of conventional SPE. The main factors affecting extraction efficiency including pH value, desorption conditions, extraction/desorption time, sample volume, and adsorbent amount were evaluated and optimized. Under the optimal conditions, a wide linear range of 0.04–8 ng mL⁻¹ with a low detection limit of 0.015 ng mL⁻¹ was obtained. The developed method was applied for extraction and preconcentration of AFM1 in three commercially available milk samples and the results were compared with the official AOAC method.     

Determination of tetracyclines residues in honey by on-line solid-phase extraction high-performance liquid chromatography

An automated system using on-line solid-phase extraction (SPE) high-performance liquid chromatography (HPLC) with ultraviolet (UV) detection was developed for the determination of tetracyclines (TCs), such as tetracycline (TC), oxytetracycline (OTC), chlortetracycline (CTC), metacycline (MC), and doxycycline (DC) in honey. One milliliter diluted honey sample was injected into a conditioned C18 SPE column and the matrix was washed out with water for 3 min. By rotation of the switching valve, TCs were eluted and transferred to the analytical column by the chromatographic mobile phase. Chromatographic conditions were optimized. TCs were separated in less than 8 min with a gradient elution using a mixture of 0.8% formic acid and acetonitrile. The UV detection was performed at 365 nm. The conditions for on-line SPE, including solvent and total time for loading sample and washing matrix were also optimized. Time for extraction and separation decreased greatly. For the five kinds of TCs, the limits of detection (LODs) at a signal-to-noise of 3 ranged from 5 to 12 ng g⁻¹. The relative standard deviations (R.S.D.) for the determination of TCs ranged from 3.4 to 7.1% within a day and ranged from 3.2 to 8.9% in 3 days, respectively.     

Direct analysis of fenvalerate isomers by liquid chromatography. Application to formulation and residue analysis of fenvalerate

Summary The separation of the optical isomers of fenvalerate [cyano(3-phenoxyphenyl)methyl 2-(4-chlorophenyl)-3-methylbutyrate] has been carried out by high-performance liquid chromatography (HPLC) on a chiral column with (R)-N-3,5-dinitrobenzoyl-phenyl-glycine (DNBPG) covalently bonded on aminopropyl silica and eluted with mixtures of methanol, 2-propanol, and hexane. The system was applied to the analysis of Pydrin^®, an emulsifiable concentrate formulation of fenvalerate, and to the residue analysis of fenvalerate in milk samples. For the analysis of Pydrin^® the only requirement was the proper dilution of Pydrin^® with hexane. For the analysis of residues in milk, fenvalerate was extracted with hexane after precipitating the milk proteins with acetonitrile and removing the precipitate by filtration; the hexane extract was concentrated to small volume and filtered before being analyzed by HPLC.