Synchronous fluorescence determination of protein with functionalized CdS nanoparticles as a fluorescence probe

Nanometer-sized fluorescent particles have been successfully synthesized. A synchronous fluorescence method, with high sensitivity and selectivity, has been developed for rapid determination of protein with functionalized CdS as a fluorescence probe. When Δλ=260 nm, maximum synchronous fluorescence is produced at 274 nm at pH 7.0. Under optimal conditions, the calibration graphs are linear over the range 0.1-3.0 μg ml⁻¹ for bovine serum albumin (BSA), 0.1-11.0 μg ml⁻¹ for γ-globulin (γ-G) and 0.1-1.4 μg ml⁻¹ for human serum albumin (HSA), respectively. Limits of determination were 0.01 μg ml⁻¹ for BSA, 0.019 μg ml⁻¹ for γ-G and 0.021 μg ml⁻¹ for HSA, respectively. The relative standard deviations of seven replicate measurements were 1.8% for 1.0 μg ml⁻¹ BSA, 2.2% for 1.0 μg ml⁻¹ γ-G and 2.3% for 1.0 μg ml⁻¹ HSA.     

Determination of proteins with Alizarin Red S by Rayleigh light scattering technique

A new protein determination method by enhanced Rayleigh light scattering (RLS) technique has been developed. In acid condition (pH=3.60), RLS of 1,2-dihydroxyanthraquinone-3-sulfonate (Alizarin Red S) can be greatly enhanced by addition of proteins, resulting in two characteristic peaks, 360 and 505 nm, respectively. The new protein assay is based on the RLS enhancement and spectrum change. The optimum condition for the reaction was investigated. The linear range is 0.20-24.9 μg ml⁻¹ for BSA and 0.20-15.5 μg ml⁻¹ for HSA. The detection limits (S/N=3) are 9.59 ng ml⁻¹ for BSA and 9.51 ng ml⁻¹ for HSA. The results of determination for human serum samples were comparable to those obtained by Bradford method. The binding stoichiometry was determined.     

Facile, sensitive and selective fluorescence turn-on detection of HSA/BSA in aqueous solution utilizing 2,4-dihydroxyl-3-iodo salicylaldehyde azine

A novel fluorescence turn-on detection method of human serum albumin (HSA) and bovine serum albumin (BSA) in aqueous solution is investigated using 2,4-dihydroxyl-3-iodo salicylaldehyde azine (DISA). Upon the addition of DISA to HSA/BSA solution, a fluorescence turn-on effect at 529 nm can be observed with a large stokes shift of ∼129 nm based on hydrophobic binding-mode between protein and dye. Under the optimal condition, the linear ranges of fluorescence intensity for HSA and BSA are 0.1-30 μg mL⁻¹ with the relative correlation coefficient of R² = 0.991 (n = 10) and 0.3-50 μg mL⁻¹ with R² = 0.997 (n = 10); and the detection limits for HSA and BSA based on IUPAC (C_DL = 3S_b/m) are 20 ng mL⁻¹ and 50 ng mL⁻¹, respectively.     

Quantitative determination of proteins by the Rayleigh light-scattering technique after optimization of the derivation reaction with Arsenazo-DBS

This paper researched the determination of proteins with 2-(2-arsonophehenylazo)-7-[(2,6-dibromo-4-sulfophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid (Arsenazo-DBS) by Rayleigh light-scattering (RLS). The reaction parameters, such as acidity, volume of buffer solution and concentration of Arsenazo-DBS, were examined by orthogonal array design (OAD). Under optimal conditions, the weak RLS of Arsenazo-DBS and BSA can be enhanced greatly and two enhanced RLS signals were produced at 340-350 and 400-420 nm. Based on this reaction, a new quantitative determination method for proteins has been developed. This method is proved to be very sensitive (the determination limits are 0.077 μg ml⁻¹ for bovine serum albumen (BSA) and 0.074 μg ml⁻¹ for human serum albumen (HSA)), rapid (<2 min), simple (one step) and tolerance of most interfering substances. The effects of different surfactants were also examined. The amount of proteins in human serum samples was determined and the maximum relative error was no more than 2% and the recovery was between 95 and 105%.     

Liquid-liquid extraction procedure exploiting multicommutation in flow system for the determination of molybdenum in plants

A liquid-liquid extraction flow analysis procedure for the spectrophotometric determination of molybdenum in plants at μg l⁻¹ level is described. The flow network comprised a set of solenoid valves assembled to implement the multicommutation approach under microcomputer control. Radiation source (LED, 475 nm), detector (photodiode) and separation chamber were nested together with the flow cell comprising a compact unit. The consumption of reagents (potassium thiocyanate and stannous chloride) and also extracting solvent (isoamyl alcohol) were optimized to 32 mg and 200 μl per determination, respectively. Accuracy was assessed by comparing results with those obtained with ICP-OES and no significant difference at 95% confidence level was observed. Other favorable characteristics such as a linear response ranging from 25 to 150 μg l⁻¹ molybdenum (r=0.999); detection limit of 4.6 μg l⁻¹ sample throughput of 25 determinations per hour and relative standard deviation of 2.5% (n=10) were also achieved.     

Study of the interaction between terazosin and serum albumin: Synchronous fluorescence determination of terazosin

The interactions between terazosin and bovine serum albumin (BSA) were studied by spectrofluorimetry. The binding constants of terazosin with BSA were measured at different temperatures. The effects of various metal ions on the binding constants of terazosin with BSA were also studied. The optimum conditions of synchronous fluorometric determination of terazosin were studied and the method was successfully applied to the determination of terazosin added to serum and urine samples (3σ detection limit 0.21 mg l⁻¹).     

A rapid and sensitive method for the determination of trace proteins based on the interaction between proteins and Ponceau 4R

The interactions between proteins and Ponceau 4R (PR) in aqueous solution have been studied by the techniques of resonance light scattering (RLS) spectroscopy, the absorption spectroscopy, zeta potential assay and circular dichroism (CD) spectrum. The dry PR can assemble on the surface of protein via electrostatic and hydrophobic forces to produce an associated compound of protein-PR, this compound can enhance the RLS of protein. Based on this fact, a simple, rapid, and sensitive method has been developed for the determination of proteins at nanogram level by RLS technique with a common spectrofluorimeter. Under optimum conditions, the linear range is 0.10-39.2 μg mL⁻¹ for the determination of both bovine serum albumin (BSA) and human serum albumin (HSA). The detection limits (S/N = 3) are 6.96 ng mL⁻¹ for BSA and 5.71 ng mL⁻¹ for HSA, respectively. There is almost no interference from amino acids, most of the metal ions, and other coexistent substances. The method has been satisfactorily applied to the direct determination of the total protein in human serum.     

Optimization of experimental parameters in single-drop microextraction-gas chromatography-mass spectrometry for the determination of periodate by the Malaprade reaction, and its application to ethylene glycol

The aim of present work was to optimize the experimental parameters in single drop microextraction under solution immersion (SDME) and headspace (HS-SDME) extraction modes for the determination of periodate using guaifenesine [3-(2′-methoxyphenoxy)-1,2-propane diol] and norephedrine (phenylpropanolamine) as new and alternative reagents for the Malaprade reaction. The reactions were complete within 5 min resulting in the formation of 2-(2′-methoxyphenoxy)-acetaldehyde and benzaldehyde, respectively. SDME/HS-SDME of oxidation products with 2 μl of anisole or 1 μl of toluene, respectively, has permitted the determination of periodate at μg l⁻¹ concentration levels. The results indicated that HS-SDME (range 0.01-10 mg l⁻¹, r² = 0.9990; limit of detection 1.55 μg l⁻¹) was more sensitive than SDME (range 0.05-50 mg l⁻¹, r² = 0.9984; limit of detection 3.42 μg l⁻¹), and was inexpensive, rapid and convenient. Tolerance of excess of iodate has permitted the application of this method in the determination of ethylene glycol in motor oil; the average recovery on spiked sample was 98.6% with R.S.D. of 4.2%.     

Spectrofluorimetric determination of human serum albumin using a doxycycline-europium probe

A new spectrofluorimetric method is proposed for determination of human serum albumin (HSA) with the limit of detection at ng levels. Using doxycycline (DC)-europium (Eu³⁺) as a fluorescent probe, in a buffer solution of pH 10.2, HSA can remarkably enhance the fluorescence intensity of the DC-Eu³⁺ complex at 612 nm and the enhanced fluorescence intensity of Eu³⁺ is proportional to the concentration of HSA. Optimum conditions for the determination of HSA are also investigated. The linear ranges for HSA are 0-9.2 and 9.2-34.5 μg ml⁻¹ with limits of detection of 64 and 115 ng ml⁻¹, respectively. This method is simple, practical and relatively free of interference from coexisting substances, as well as much more sensitive than most of the existing assays. The determination results for human serum and urine samples are identical to those by the AOAO method, with relative standard deviations of five determinations of 1.1-3.6%. By the Rosenthal graphic method, the binding number and association constant of human serum albumin with the probe are 1.8 and 3.71×10⁵ l mol⁻¹, respectively.     

Study on the interaction between oxolinic acid aggregates and protein and its analytical application

It was found that oxolinic acid (OA) at high concentration can self-assemble into nano- to micro- meter scale OA aggregates in Tris-HCl (pH 7.48) buffer solution. The nanoparticles of OA were adopted as fluorescence probes in the quantitative analysis of proteins. Under optimum conditions, the fluorescence quenching extent of nanometer scale OA aggregates was in proportion to the concentration of albumins in the range of 3.0 × 10⁻⁸ to 3.0 × 10⁻⁵ g mL⁻¹ for bovine serum albumin (BSA) and 8.0 × 10⁻⁸ to 8.0 × 10⁻⁶ g mL⁻¹ for human serum albumin (HSA). The detection limits (S/N = 3) were 3.4 × 10⁻⁹ g mL⁻¹ for BSA, and 2.6 × 10⁻⁸ g mL⁻¹ for HSA, respectively. Samples were satisfactorily determined. The interaction mechanism of the system was studied using fluorescence, UV-vis, resonance light scattering (RLS) and transmission electron microscope (TEM) technology, etc., indicating that the nonluminescent complex was formed between serum albumin molecular and OA, to disaggregate the self-association of OA, which resulted in the dominated static fluorescence quenching in the system.     

Simultaneous determination of fluorophores with overlapped spectra by sequential injection analysis coupled to variable angle scanning fluorescence spectrometry and multivariate linear regression algorithms

An automated and versatile sequential injection spectrofluorimetric procedure for the simultaneous determination of multicomponent mixtures in micellar medium without prior separation processes is reported. The methodology is based upon the segmentation of a sample slug between two different buffer zones in order to attain both an improvement of sensitivity and residual minimization for the whole species. Resolution of overlapping fluorescence profiles is achieved using a variable angle scanning technique coupled to multivariate least-squares regression (MLR) algorithms at both sample edges.The potentialities of the described methodology are illustrated with the spectrofluorimetric determination of four widespread pesticides with different acid-base properties; viz. carbaryl (CBL) (1-naphthyl-N-methylcarbamate), fuberidazole (FBZ) (2-(2′-furyl)benzimidazole), thiabendazole (TBZ) (2-(4′-thiazolyl)benzimidazole) and warfarin (W) (3-α-acetonylbenzyl)-4-hydroxycoumarin). Detection limits at the 3σ level were 3.9, 0.02, 0.03 and 10 μg l⁻¹ for CBL, FBZ, TBZ and W, respectively at the maximum sensitivity pH. Dynamic ranges of 13-720 μg l⁻¹ CBL, 0.10-14 μg l⁻¹ FBZ, 0.19-60 μg l⁻¹ TBZ and 0.05-5 mg l⁻¹ W were achieved. Relative standard deviations (n=10) were 0.2% for 100 μg l⁻¹ CBL and 2.4 μg l⁻¹ FBZ, 0.7% for 8 μg l⁻¹ TBZ and 1.0% for 1 mg l⁻¹ W. The proposed automated methodology, which handles 17 samples/h, was validated and applied to spiked real water samples with very satisfactory results.     

A continuous flow system combined with a sensing fluorimetric transductor for the determination of β-naphthol

A single automatic method for continuous flow determination of β-naphthol based on the enhancement of its native fluorescence once the analyte was transitorily retained on-line on a solid support (QAE A-25 resin) is reported. So, a flow-through optosensor was developed using a flow-injection analysis system with solid phase fluorimetric transduction. KCl (0.15 mol l⁻¹) at pH 12.0 was used as carrier solution. To obtain the optimum fluorescence signal the wavelengths chosen were 245 nm (excitation) and 420 nm (emission). The response of the sensor was directly proportional to the sample volume injected in the studied range 40-1500 μl. Approximately one higher order of magnitude is achieved in sensitivity when 1500 μl are used with respect to the use of 40 μl of sample. The sensor was calibrated for three different injection volumes: 40, 600 and 1500 μl, responding linearly in the measuring range of 2-60, 0.5-15 and 0.2-5 μg l⁻¹ with detection limits of 0.5, 0.09 and 0.05 μg l⁻¹, respectively. The relative standard deviation for ten independent determination is 0.6% (40 μl), 0.9% (600 μl) and 2.3% (1500 μl). A recovery study was performed onto three different spiked water samples at concentration levels from 1 to 2.5 μg l⁻¹ and the recovery percentage from the experimental data ranged between 101±2 and 105±5.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.     

Analytical strategy photodegradation/chemiluminescence/continuous-flow multicommutation methodology for the determination of the herbicide Propanil

The present paper is dealing with an analytical strategy based on coupling photodegradation, chemiluminescence and multicommutation continuous-flow methodology for the determination of the pesticide Propanil, a common herbicide. The pesticide solution is inserted as small segments sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. Both flow-rates (sample and medium) are adjusted to required time for photodegradation, 2.0 min; and then, the resulting solution is also sequentially inserted as segments alternated with segments of the oxidizing solutions system, 1.00 × 10⁻⁴ mol l⁻¹ potassium permanganate in 2.00 mol l⁻¹ sulphuric acid medium. The calibration range, from 10 μg l⁻¹ to 25 mg l⁻¹, resulted in a linear behaviour over the range 10 μg l⁻¹-5 mg l⁻¹ and fitting the linear equation: I = 780.30C + 95.28; correlation coefficient 0.9999. The limit of detection was 8 μg l⁻¹ and the sample throughput 20 h⁻¹. After testing the influence of a large series of potential interferents the method is applied to water samples obtained from different places and to one formulation. The method is valid for the determination of other pesticides from the same chemical family, namely: alachlor, flumetsulam, furalaxyl and ofurace. Calibration graphs, limits of detection, repeatability and determination in water samples are obtained for each reported pesticide.     

Part-per-trillion determination of chlorobenzenes in water using dispersive liquid-liquid microextraction combined gas chromatography-electron capture detection

In this study, a simple, rapid and efficient method, dispersive liquid-liquid microextraction (DLLME) combined gas chromatography-electron capture detection (GC-ECD), for the determination of chlorobenzenes (CBs) in water samples, has been described. This method involves the use of an appropriate mixture of extraction solvent (9.5 μl chlorobenzene) and disperser solvent (0.50 ml acetone) for the formation of cloudy solution in 5.00 ml aqueous sample containing analytes. After extraction, phase separation was performed by centrifugation and the enriched analytes in sedimented phase were determined by gas chromatography-electron capture detection (GC-ECD). Our simple conditions were conducted at room temperature with no stiring and no salt addition in order to minimize sample preparation steps. Parameters such as the kind and volume of extraction solvent, the kind and volume of disperser solvent, extraction time and salt effect, were studied and optimized. The method exhibited enrichment factors and recoveries ranging from 711 to 813 and 71.1 to 81.3%, respectively, within very short extraction time. The linearity of the method ranged from 0.05 to 100 μg l⁻¹ for dichlorobenzene isomers (DCB), 0.002-20 μg l⁻¹ for trichlorobenzene (TCB) and tetrachlorobenzene (TeCB) isomers and from 0.001 to 4 μg l⁻¹ for pentachlorobenzene (PeCB) and hexachlorobenzene (HCB). The limit of detection was in the low μg l⁻¹ level, ranging between 0.0005 and 0.05 μg l⁻¹. The relative standard deviations (R.S.D.s) for the concentration of DCB isomers, 5.00 μg l⁻¹, TCB and TeCB isomers, 0.500 μg l⁻¹, PeCB and HCB 0.100 μg l⁻¹ in water by using the internal standard were in the range of 0.52-2.8% (n = 5) and without the internal standard were in the range of 4.6-6.0% (n = 5). The relative recoveries of spiked CBs at different levels of chlorobenzene isomers in tap, well and river water samples were 109-121%, 105-113% and 87-120%, respectively. It is concluded that this method can be successfully applied for the determination of CBs in tap, river and well water samples.     

Spectrophotometric catalytic determination of Fe(III) in estuarine waters using a flow-batch system

A flow-batch system was developed for the determination of Fe(III) in estuarine waters with high variability in salinity. The method is based on the catalytic effect of iron(III) on the oxidation rate of N,N-dimethyl-p-phenylenediammonium dichloride (DmPD) by hydrogen peroxide and the formed product is spectrophotometrically monitored at 554 nm. A controlled addition of sodium chloride to every assayed sample is accomplished for in-line individual salinity matching.The proposed system processes about 30 samples h⁻¹ and yields reproducible results. Relative standard deviations were estimated as <1.5% after 10 injections of typical samples (10.0-50.0 μg l⁻¹ Fe; ca. 0.5 mol l⁻¹ Cl). Synthetic samples (15.0 μg l⁻¹ Fe; 0.25-1.0 mol l⁻¹ NaCl) were efficiently processed, and no significant differences in results were found at a probability level of 99.7%. The method works for the full range of salinities. Only 120 μg DmPD are consumed per determination. The analytical curve is linear up to about 60 μg l⁻¹ Fe (r>0.999; n=5) and the detection limit is 5 μg l⁻¹ Fe. Results are in agreement with graphite furnace atomic absorption spectrometry.     

Determination of ethylphenol compounds in wine by headspace solid-phase microextraction in conjunction with gas chromatography and flame ionization detection

Headspace solid phase microextraction (HS-SPME) was investigated as a solvent-free alternative method for the extraction and determination of 4-ethylphenol (EP) and 4-ethylguaiacol (EG) in red wine by capillary gas chromatography with flame ionization detection (FID) and compared to liquid-liquid extraction.For HS-SPME, better results were obtained with saturated sodium chloride samples, at 55 °C, using a 85 μm polyacrylate fiber. An absorption time of 40 min was needed to reach the absorption equilibrium for EG. This 40-min duration corresponds to the beginning of EP equilibrium and was selected for the experiments. In these conditions, the calibration graphs were linear in the range 5-5000 μg l⁻¹ and the sensitivity was nearly the same for the two compounds. The detection limits were in the low μg l⁻¹ range. In model wine solutions, result obtained with the liquid-liquid extraction method exhibit a linear calibration between 25 and 10,000 μg l⁻¹ with a detection limit of 1 μg l⁻¹, but, the relative standard deviations of the EP and EG result in the low concentration range (<50 μg l⁻¹) are higher than those obtained by HS-SPME (15% compared to 2% for EP and 12% compared to 5% for EG). Taking into account the numerous volatile compounds in wine, HS-SPME is a rapid and valid alternative technique for use in the determination of ethylphenols at trace levels.     

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG)₂ complex was eluted with 1 mol l⁻¹ HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml⁻¹ Na⁺, K⁺, Mg²⁺, Al³⁺ and Fe³⁺; 5000 μg ml⁻¹ Ca²⁺ ; 500 μg ml⁻¹ Pb²⁺; 125 μg ml⁻¹ Zn²⁺; 50 μg ml⁻¹ Cu²⁺ and 25 μg ml⁻¹ Ni²⁺ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l⁻¹, respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg⁻¹ and 4.06 mg g⁻¹, respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples.     

Development of a sequential injection system for trace mercury determination by cold vapour atomic absorption spectrometry utilizing an integrated gas-liquid separator/reactor

A simple and robust time-based on-line sequential injection system for trace mercury determination via cold vapour atomic absorption spectrometry (CVAAS), employing a new integrated gas-liquid separator (GLS), which in parallel operates as reactor, was developed. Sample and reductant are sequentially loaded into the GLS while an argon flow delivers the released mercury vapour through the atomic absorption cell. The proposed method is characterized by the ability of successfully managing variable sample volume up to 30 ml in order to achieve high sensitivity. For 20 ml sample volume, the sampling frequency is 25 h⁻¹. The calibration curve is linear over the concentration range 0.05-5.0 μg l⁻¹ of Hg(II), the detection limit is c_L = 0.02 μg l⁻¹, and the relative standard deviation is s_r = 2.6% at 1.0 μg l⁻¹ Hg(II) level. The performance of the proposed method was evaluated by analyzing certified reference material and applied to the analysis of natural waters and biological samples.     

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l⁻¹ for copper and 0.1-5 mg l⁻¹ for iron, respectively, with a sampling rate of 18 h⁻¹. The limits of detection are 50 μg l⁻¹ for copper and 25 μg l⁻¹ for iron. The relative standard deviations (n = 15) are 2% for 0.5 mg l⁻¹ copper and 1.8% for 0.5 mg l⁻¹ iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l⁻¹ of copper and 0.2-5 mg l⁻¹ of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.