Determination of hydrogen peroxide by using a flow injection system with immobilized peroxidase and long pathlength capillary spectrophotometry

The development of a highly sensitive method for the determination of nanomolar concentrations of hydrogen peroxide in the liquid phase is described. This paper demonstrates for the first time a flow injection analysis (FIA) system with immobilized enzyme reactor combined with a total internal reflective cell (a liquid waveguide capillary cell (LWCC)) and spectrophotometric detection, for the development of an improved procedure for the determination of hydrogen peroxide. Moreover, the newly synthesized 4-aminopyrazolone derivative, 4-amino-5-(p-aminophenyl)-1-methyl-2-phenyl-pyrazol-3-one (DAP), is used as a color coupler in its oxidative condensation with the sodium salt of N-ethyl-N-sulphopropylaniline sodium salt (ALPS) which acts as a hydrogen donor. Immobilization of peroxidase is achieved by coupling the periodate-treated enzyme to aminopropyl controlled-pore glass (CPG) beads. The determination of hydrogen peroxide is carried out in a 0.1 M phosphate buffer and the product is monitored at 590 nm with a charge-coupled device (CCD) detector equipped with fiber optics in a fully computerized system. The interference of different species, mainly ionic, was investigated.The method permits detection down to 4 nmol l⁻¹ hydrogen peroxide (signal-to-noise ratio=3). A linear calibration graph was obtained over the range 20-700 nmol l⁻¹. The relative standard deviation (R.S.D.) at 300 nmol l⁻¹ H₂O₂ is 1.7% (n=7). The method was successfully applied for the determination of hydrogen peroxide in samples from a vat-cleaning process.     

Determination of 3-amino-1,2,4-triazole (amitrole) in environmental waters by capillary electrophoresis

3-Amino-1,2,4-triazole (amitrole) is a widely used pesticide, with many difficulties to be analyzed at the regulatory level in drinking water, because its high solubility in water. This paper describes a simple and fast method for the simultaneous determination of amitrole and atrazin-2-hydroxy, principal degradation product of s-triazines, by capillary zone electrophoresis. Separation and determination of these herbicides in water samples was performed in 0.02 mol l⁻¹ phosphate buffer at pH 3.2. The method allows determination of the amitrole and atrazin-2-hydroxy in water samples in concentration lower than 100 μg l⁻¹. The detection limits using a previous preconcentration step of amitrole in Alberche River (Comunidad Autónoma de Madrid, Spain) and drinking water spiked samples was of 4 μg l⁻¹.     

Determination of diphenhydramine by capillary electrophoresis with tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence detection

Tris(2,2′-bipyridyl)ruthenium(II) electrochemiluminescence detection in a capillary electrophoresis separation system was used for the determination of diphenhydramine. In this study, platinum disk electrode (300 μm in diameter) was used as a working electrode and the influence of applied potential and buffer conditions were investigated. Under optimal conditions: 1.2 V applied potential, pH 8.50, 15 kV separation voltage and 10 mmol l⁻¹ running buffer, the calibration curve of diphenhydramine was linear over the range of 4×10⁻⁸ to 1×10⁻⁵ mol l⁻¹. This technique gave satisfactory precision, and relative standard deviations of migration times and chemiluminescence peak intensities were less than 1 and 6%, respectively. The technique was applied to animal studies for determination of diphenhydramine extracted from rabbit plasma and urine samples, and the extraction efficiency were between 92 and 98.5%.     

Application of SiO2-poly(dimethylsiloxane) hybrid material in the fabrication of amperometric biosensor

A highly sensitive adsorptive stripping voltammetric protocol for measuring trace beryllium, in which the preconcentration is achieved by adsorption of the beryllium-arsenazo-I complex at a preplated mercury-coated carbon-fiber electrode, is described. Optimal conditions were found to be a 0.05 M ammonium buffer (pH 9.7) containing 5 μM arsenazo-I, an accumulation potential of 0.0 V (versus Ag/AgCl) and a square-wave voltammetric scan. The new procedure obviates the need for renewable mercury-drop electrodes used in early stripping protocols for beryllium. A linear response is observed over the 10-60 μg l⁻¹ concentration range (90 s accumulation), along with a detection limit of 0.25 μg l⁻¹ beryllium (10 min accumulation). A 15-s electrochemical cleaning enables the same mercury film to be used for a prolonged operation. High stability is thus indicated from the reproducible response of a 100 μg l⁻¹ beryllium solution (n = 60; RSD = 3.3%) over a 2.5-h operation. Applicability to a seawater sample is illustrated. The attractive behavior of the new sensor holds great promise for on-site environmental and industrial monitoring of beryllium. Preliminary data in this direction using mercury-coated screen-printed electrodes are encouraging.     

Simultaneous UV and electrochemical determination of the herbicide asulam in tap water samples by micellar electrokinetic capillary chromatography

A simple end-column electrochemical detector was designed and attached to an available commercial capillary electrophoresis instrument with UV detection to detect different kind of herbicides and to determinate methyl-4-aminophenyl-sulfonylcarbamate (asulam) in water samples. The designed cell is very easy to assemble and disassemble in a short period of time; the working electrode positioning is also quickly achieved without micropositioners. The alignment between working electrode and capillary outlet was very reproducible for the all checked electrodes; the R.S.D. obtained was lower than 6.0% for 100 μm gap distance. In this mode, the non-electroactive and electroactive compounds could be detected by UV and electrochemical detection, respectively at the same time. The electrochemical determination of asulam using micellar electrokinetic capillary chromatography (MEKC) is the first time that is reported. In both detection systems, a linear range was obtained for asulam concentrations lower than 25.0 mg l⁻¹, in boric acid 0.020 mol l⁻¹ at pH 8.20 and containing 0.025 mol l⁻¹ of sodium dodecyl sulfate, to obtain selectivity additional separation by the micellar distribution process. Under these conditions, an experimental detection limit of 0.4 mg l⁻¹ was achieved. A new experimental scheme is also described for asulam determination in tap waters with a previous preconcentration step. Using both, UV and electrochemical detection, with a previous extraction procedure, the detection limits of asulam in tap water samples were of 1.0 and 0.8 μg l⁻¹, respectively.     

Microfluidic liquid-liquid extraction system based on stopped-flow technique and liquid core waveguide capillary

In this work, a miniaturized liquid-liquid extraction system under stopped-flow manipulation mode with spectrometric detection was developed. A Teflon AF liquid-core waveguide (LCW) capillary was used to serve as both extraction channel for organic solvent flow and adsorption detection flow cell. Gravity induced hydrostatic pressure was used to drive the organic and aqueous phases through the extraction channels. During extraction process, a stable organic and aqueous phase interface was formed at the outlet of the capillary, through which the analyte in the flowing aqueous stream was extracted into the stationary organic solvent in capillary. The absorbance of the analyte extracted into the organic solvent was measured in situ by a spectrometric detection system with light emitting diode (LED) as light source and photodiode as absorbance detector. The performance of the system was demonstrated in the determination of sodium dodecyl sulfate (SDS) extracted as an ion pair with methylene blue into chloroform. The precision of the measured absorbance for a 5 mg L⁻¹ SDS standard was 6.1% R.S.D. (n = 5). A linear response range of 1-10 mg L⁻¹ SDS was obtained with 5 min extraction period. The limit of detection (LOD) for SDS based on three times standard deviation of the blank response was 0.25 mg L⁻¹.     

Evaluation of a carbon paste electrode modified with organofunctionalized amorphous silica in the cadmium determination in a differential pulse anodic stripping voltammetric procedure

The determination of cadmium using a carbon paste electrode modified with organofunctionalized amorphous silica with 2-benzothiazolethiol was investigated. The Cd(II) oxidation peak was observed around −0.80 V (vs. SCE) in phosphate buffer (pH 4.0) in differential pulse anodic stripping voltammetry. The best results were obtained under the following optimized conditions: 1 min accumulation time, 50 mV pulse amplitude, 20 mV s⁻¹ scan rate in phosphate buffer pH 4.0. Using such parameters a linear dynamic range from 5.6×10⁻⁷ to 3.5×10⁻⁵ mol l⁻¹ Cd(II) was observed with a sensitivity of 2.83 μA mol⁻¹ l, limit of detection 1.0×10⁻⁷ mol l⁻¹. Cd(II) spiked in a natural water sample was determined with 99% mean recovery at 10⁻⁷ mol l⁻¹ level. Interference were also evaluated.     

Spectrophotometric determination of trace lead in water after preconcentration using mercaptosephadex

A highly sensitive and selective spectrophotometric method for determination of trace lead in water after pre-concentration using mercaptosephadex (MS-50) has been developed, the method based on the color reaction of lead(II) with dibromohydroxylphenylporphyrin. Under optimal condition, lead(II) reacts with the reagent to form a 1:2 yellow complex in presence of TritonX-100, which has a maximum absorption peak at 479 nm. The color reaction can complete rapidly and remain stable for 24 h in room temperature. The molar absorption coefficient of the lead complex, the limit of quantification, the limit of detection and relative standard deviations were found to be 2.35×10⁵ l mol⁻¹ cm⁻¹, 4.3, 1.4 ng ml⁻¹ and 1.0%, respectively. The absorbance of the lead complex at 479 nm is linear up to 0.48 μg ml⁻¹ of lead(II). The effect of various co-existing ions in water were examined seriously. No interference was observed. Moreover, a simple pre-concentration method for trace lead in water was also studied using MS-50. It was found that trace lead in water can be adsorbed in 1.0 mol l⁻¹ HCl and dissociated from MS-50 with 4.0 mol l⁻¹ HCl quantitatively, that improves the selectivity and the sensitivity of method (its detection limit (3 s) changed into 0.2 ng ml⁻¹ of lead) obviously. The proposed method has been applied to determine trace lead in water samples with satisfactory results.     

Capillary waveguide nucleic acid based biosensor

Micro-capillaries are finding increasing utility in the development of portable analytical sensors. We present design guidelines for optimizing the collection of free propagating fluorescence for capillary waveguide sensors used in the detection of nucleic acids. A dual function integrated opto/fluid connector is also described. Evanescent wave excitation of the coating layer containing a DNA probe is achieved by using a fiber optic ring arrangement for coupling light directly into the capillary wall. The central part of the connector is used for injecting a DNA or RNA target into the capillary channel. In situ hybridization has been used to detect target molecules at a concentration of 30 pg ml⁻¹. The sensor can be regenerated for repeated detection of DNA or RNA targets.     

Ultra-simple adaptor to convert batch cells with mercury drop electrodes in voltammetric detectors for flow analysis

A simple, robust and fast-responding flow adaptor for mercury drop electrodes (MDEs) is described. An L-shaped PTFE tube with an internal diameter of 0.5 mm is fixed with a silicone ring on the glass capillary of a MDE, in such a way as to direct the outcoming flow onto the mercury drop, from a distance of about 0.5 mm. Any commercial or laboratory-made batch cell, provided with an MDE, serves for the purpose. The level of supporting electrolyte in the cell is maintained constant through a siphon or a lateral draining orifice. The adaptor is compatible with all the different brands and operating modes of the MDEs (free dropping, controlled drop time, renewable static drop, hanging drop or sessile drop). Flow injection experiments were conducted with the following amperometric detection modes: sampled-DC, reverse pulse amperometry (RPA), and anodic stripping voltammetry (ASV). The FIA-RPA peaks presented a R.S.D.<0.8% for 1.0×10⁻⁵ mol l⁻¹ lead(II) (N=30, V_sample=100 μl). The response time (0-63% of the signal maximum) to a concentration step is 1.2 s for 500 μl injections of 0.1 mmol l⁻¹ ascorbic acid in acetate buffer at a flow rate of 1 ml min⁻¹, which corresponds to a response volume of 20 μl. As an example of practical application, copper(II) was determined in fertilizers by RPA using the standard addition method, at an analytical frequency of 90 injections per h.     

Diffusion layer titration of dipyrone in pharmaceuticals at a dual-band electrochemical cell

This paper describes the use of a thin-layered dual-band electrochemical cell operating at flow conditions to determine dipyrone (sodium salt of 1-phenil-2,3-dimethyl-4-methylaminomethanesulfonate-5-pyrazolone) by reaction with electrogenerated iodine. The electrolytic cell consisted of two closely spaced gold electrodes, the upper stream electrode serving as the generator electrode and the downstream electrode working as the collector electrode. A linear dynamic range from 2 to 15 μmol l⁻¹ dipyrone was obtained by using a sample volume of 100 μl, with a detection limit of 1.1 μmol l⁻¹. Standard deviation (S.D.) of 3.4% for 20 repetitive injections of a 40 μmol l⁻¹ dipyrone solution and sampling frequency of 90 h⁻¹ were achieved. The results obtained with the thin-layered dual-band electrochemical cell for dipyrone determination in three different pharmaceutical samples compared well with those found by iodimetry with coulometrically generated iodine.     

Determination of ethylphenol compounds in wine by headspace solid-phase microextraction in conjunction with gas chromatography and flame ionization detection

Headspace solid phase microextraction (HS-SPME) was investigated as a solvent-free alternative method for the extraction and determination of 4-ethylphenol (EP) and 4-ethylguaiacol (EG) in red wine by capillary gas chromatography with flame ionization detection (FID) and compared to liquid-liquid extraction.For HS-SPME, better results were obtained with saturated sodium chloride samples, at 55 °C, using a 85 μm polyacrylate fiber. An absorption time of 40 min was needed to reach the absorption equilibrium for EG. This 40-min duration corresponds to the beginning of EP equilibrium and was selected for the experiments. In these conditions, the calibration graphs were linear in the range 5-5000 μg l⁻¹ and the sensitivity was nearly the same for the two compounds. The detection limits were in the low μg l⁻¹ range. In model wine solutions, result obtained with the liquid-liquid extraction method exhibit a linear calibration between 25 and 10,000 μg l⁻¹ with a detection limit of 1 μg l⁻¹, but, the relative standard deviations of the EP and EG result in the low concentration range (<50 μg l⁻¹) are higher than those obtained by HS-SPME (15% compared to 2% for EP and 12% compared to 5% for EG). Taking into account the numerous volatile compounds in wine, HS-SPME is a rapid and valid alternative technique for use in the determination of ethylphenols at trace levels.     

On-line preconcentration and determination of nickel in natural water samples by flow injection-inductively coupled plasma optical emission spectrometry (FI-ICP-OES)

An on-line nickel preconcentration and determination system implemented with inductively coupled plasma optical emission spectrometry (ICP-OES) associated to flow injection (FI) was studied. Trace amounts of nickel were preconcentrated by sorption on a conical minicolumn packed with activated carbon (AC) at pH 5.0. The nickel was removed from the minicolumn with 20% nitric acid. An enrichment factor of 80-fold for a sample volume of 50 ml was obtained. The detection limit (DL) value for the preconcentration method proposed was 82 ng l⁻¹. The precision for ten replicate determinations at the 0.5 μg l⁻¹ Ni level was 3.0% relative standard deviation (R.S.D.), calculated from the peak heights obtained. The calibration graph preconcentration method for nickel was linear with a correlation coefficient of 0.9997 at levels near the detection limits (DL) up to at least 100 μg l⁻¹. The method was successfully applied to the determination of nickel in natural water samples.     

Semi-online preconcentration of Cd, Mn and Pb on activated carbon for GFASS

This paper presents a method whereby trace elements in NH₄Cl-NH₃ medium are adsorbed on activated carbon in a micro-flow-injection (FI) semi-online sorbent extraction preconcentration system and then determined by graphite furnace atomic absorption spectrometry (GFAAS). The analytical performance of the proposed method for determining Cd, Mn and Pb was studied. A microcolumn packed with activated carbon was used as a preconcentration column (PCC). The metals to be determined were preconcentrated onto the column for 60 s and then rinsed with 0.02% (v/v) HNO₃ and eluted with 30 μl of 2 mol l⁻¹ HNO₃. Compared with the direct injection of 30 μl of aqueous sample solution, enrichment factor of 32, 26, and 21 and detection limits (3σ) of 0.4, 4.7, and 7.5 ng l⁻¹ for Cd, Mn and Pb, respectively, were obtained with 60 s sample loading at 3.0 ml min⁻¹ for sorbent extraction, 30 μl of eluate injection, and peak area measurement. The precisions (RSD, n=6) were 2.8% at the 0.05 μg l⁻¹ level for Cd, 3.0% at the 0.3 μg l⁻¹ level for Mn, and 3.1% at the 0.5 μg l⁻¹ level for Pb. The experimental results indicate that the procedure can eliminate the fundamental interferences caused by alkali and alkaline earth metals and the application of it to the determination of Cd, Mn and Pb in some water samples is successful.     

Light-emitting-diode-induced fluorescence detector for capillary electrophoresis using optical fiber with spherical end

A simple fluorescence detector for capillary electrophoresis (CE) using a blue light-emitting-diode (LED) as excitation source is constructed and evaluated. An optical fiber was used to collect the fluorescence, and a flat end of the fiber was modified to spherical end, resulting in 50% increase of efficiency over the flat end. A simple device for optical alignment of the fibers and capillary column was designed. The concentration and mass detection limits for fluorescein were 1.8×10⁻⁷ mol l⁻¹ and 4.3 femol, respectively.     

Liquid core waveguide-based optical spectrometry for field estimation of dissolved BTEX compounds in groundwater: A feasibility study

The utility of a liquid core waveguide (LCW) system for acting as a sentry monitor for compounds such as benzene, toluene, ethylbenzene, xylene (BTEX) in water was examined. A vapor-permeable LCW suitable for long path length absorbance spectroscopy based on a Teflon AF 2400 tube was fabricated. Multiwavelength spectroscopy in the near-UV was carried out using a fiber optic-based flashlamp-photodiode array (PDA) combination with hexane as the solvent in the waveguide core. Using multicomponent calibration, quantitation of benzene and toluene accurate to 6±5% could be conducted at sub-mg l⁻¹ levels in mixtures after a sampling period of 10 min.     

Synthesis and application of a functionalized resin in on-line system for copper preconcentration and determination in foods by flame atomic absorption spectrometry

An on-line system for preconcentration and determination of copper at μg l⁻¹ level by flame atomic absorption spectrometry (FAAS) is proposed. Amberlite XAD-2 functionalized with 3,4-dihydroxybenzoic acid packed in a minicolumn was used as sorbent. Copper(II) ions were sorbed in the minicolumn, from which it could be eluted by hydrochloric acid solution directly to the nebulizer-burner system of the FAAS. Eluent solution was carried by water at a flow rate of 5.00 ml min⁻¹. Signals were measured as peak height by using an instrument software. Achieved sampling rate was 27 samples per hour. Analytical parameters were evaluated and the results demonstrated that copper can be determined, with acetate buffer to adjust the sample pH at 6.0, preconcentration time of 120 s and a sample flow rate of 6.50 ml min⁻¹. The desorption was carried out with 30 μl of a 1.0 mol l⁻¹ hydrochloric acid solution. An enrichment factor of 33 in 13.00 ml of sample (120 s preconcentration time) was achieved by using the time-based technique. The detection limit (DL) (3 s) was 0.27 μg l⁻¹ and the precision (assessed as the relative standard deviation) reached values of 5.7-1.1% in copper solutions of 5.00 to 50.00 μg l⁻¹ concentration, respectively. The accuracy of procedure was confirmed by copper determination in certified reference materials. Recoveries of spike additions (1.0 or 2.0 μg g⁻¹) to food samples were quantitative (90.0-110.0%). These results proved also that the procedure is not affected by matrix interference and can be applied satisfactorily for copper determination in rice flour and starch samples.     

Preparation and characterization of p-tert-butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography

p-tert-Butylcalix[8]arene bonded capillaries for open-tubular capillary electrochromatography were prepared with γ-glycidoxypropyltrimethoxysilane as a bridge. The bonded capillary displayed low and steady electroosmotic flow (EOF) values over the pH range from 4 to 9. Detection limits for direct spectrophotometric detection at 277 nm for benzenediols (at a signal to noise ratio of 2) were 0.96 mg l⁻¹ for the unbonded capillary and 1.48 mg l⁻¹ for the bonded capillary, showing that the bonded layer did not show significant absorbance and hence decreased sensitivity. The bonded capillaries showed good separation selectivity for o-, m- and p-benzenediols, α- and β-naphthols, and α- and β-naphthylamines. This selectivity was attributed to significant interactions between the analytes and the bonded p-tert-butylcalix[8]arene, which contributed to the electrochromatographic separation mechanism. The bonded capillaries gave high stability and reproducibility.     

Characterization of a microwave microstrip helium plasma with gas-phase sample introduction for the optical emission spectrometric determination of bromine,chlorine, sulfur and carbon using a miniaturized optical fiber spectrometer

Continuous flow generation of Br₂, Cl₂ and H₂S coupled to a low-power 2.45 GHz microwave microstrip He plasma exiting from a capillary gas channel in a micro-fabricated sapphire wafer with microstrip lines has been used for the optical emission spectrometric determination of Br, Cl and S using a miniaturized optical fiber CCD spectrometer. Under optimized conditions, detection limits (3σ) of 330, 190 and 220 μg l^− 1 for Br, Cl and S, respectively, under the use of the Br II 478.5 nm, Cl I 439.0 nm and S I 469.0 nm lines were obtained and the calibration curves were found to be linear over 2 orders of magnitude. In addition, when introducing CO₂ and using the rotational line of the CN molecular band at 385.7 nm the detection limit for C was 4.6 μg l^− 1. The procedure developed was found to be free from interferences from a number of metal cations and non-metal anions. Only the presence of CO₃²⁻ and CN⁻ was found to cause severe spectral interferences as strong CN and C₂ molecular bands occurred as a result of an introduction of co-generated CO₂ and HCN into the plasma. With the procedure described Br, Cl and S could be determined at a concentration level of 10–30 mg l^− 1 with accuracy and precision better than 2%.     

A simple and selective flow-injection spectrophotometric determination of copper(II) by using acetylsalicylhydroxamic acid

A new simple, and rapid flow-injection spectrophotometric method is developed for the determination of trace amounts of Cu(II) by using a new chromogenic reagent acetylsalicylhydroxamic acid (AcSHA). The method is based on the formation of colored Cu(II)-(AcSHA)₂ complex. The optimum conditions for the chromogenic reaction of Cu(II) with AcSHA is studied and the colored (green) complex is selectively monitored at λ_max 700 nm. With the reagent carrier solvent (dimethylsulfoxide (DMSO) and acetate buffer, pH 4.2) flow-rate of 1 ml min⁻¹, a detection limit (2S) of 1 μg l⁻¹ Cu(II) was obtained at a sampling rate of 80 sample h⁻¹. The calibration graph was linear in the Cu(II) concentration range 5-120 μg l⁻¹. The relative standard deviation (n=10) was 0.64% for a sample containing 60 μg l⁻¹ Cu(II). The detailed study of various interferences confirmed the high selectivity of the developed method. The method was successfully applied to determine trace amounts of copper(II) in river and seawater samples. The accuracy of the method was demonstrated by the analysis of standard reference materials C12X3500 and C14XHS 50.