DDB liver drug as a novel ionophore for potentiometric barium (II) membrane sensor

Dimethyl-4,4-dimethoxy-5,6,5′,6′-dimethylene dioxy biphenyl-2,2-dicarboxylate (DDB) liver drug is used as a novel ionophore in plasticized poly (vinyl chloride) (PVC) matrix membrane sensors for barium ions. Optimum performance characteristics are displayed by membrane sensor incorporating DDB ionophore, potassium tetrakis(4-chlorophenyl)borate as lipophilic salt, and o-nitrophenyloctyl ether as plasticizer. The sensor exhibits a linear response over the concentration range 10⁻¹-10⁻⁵ mol l⁻¹ BaCl₂ with a Nernstian slope of 30 mV per decade and high selectivity towards Ba²⁺ with respect to Li⁺, Na⁺, K⁺, Rb⁺, NH₄⁺, Mg²⁺, Ca²⁺, Sr²⁺, Mn²⁺, Co²⁺, Ni²⁺, Cd²⁺, Al³⁺, La³⁺, and Ce³⁺ ions. The sensor response is stable over a wide pH range (4-9) and the lifetime is about 2 months. The proposed sensor is successfully applied to the determination of Ba²⁺contents of some rocks.     

Quantitative parameters for the sequestering capacity of polyacrylates towards alkaline earth metal ions

The complex formation constants of polyacrylic (PAA) ligands (1.4≤log N≤2.4, N=number of monomer units) with calcium and magnesium ions were determined in different ionic media at different ionic strengths, 0≤I≤1 mol l⁻¹, at t=25 °C. Experimental pH-metric data in the presence of Ca²⁺ or Mg²⁺ were firstly analysed in terms of apparent protonation constants, log K^H*, using the “three parameter model” proposed by Högfeldt; differences in log K^H*, determined in different ionic media, were interpreted in terms of complex species formation. The only species present in the system M-PAA (M=Ca²⁺ or Mg²⁺) is ML₂: attempts to find species of different stoichiometry were unsuccessful. The stability dependence of this species on ionic strength, on the degree of neutralisation (α) and on PAA molecular weight is discussed using empirical equations. The formation constant, log β₂, is significantly higher for Ca²⁺ than for Mg²⁺: at I=0.1 mol l⁻¹ (NaCl), log N=1.8 and α=0.5, log β₂^Ca=4.43 and log β₂^Mg=4.24. The formation of polyacrylate-alkaline earth metal complexes is discussed in the light of sequestering effects in natural waters.     

A highly selective pyrene based fluorescent sensor toward Hg detection

A new pyrene-containing fluorescent sensor has been synthesized from 2,3,3-trimethylindolenine. Spectroscopic and photophysical properties of sensor are presented. The large change in fluorescence intensity (I/I₀ = 0.13) at 381 nm and affinity to Hg²⁺ over other cations such as K⁺, Na⁺, Ca²⁺, Mg²⁺, Pb²⁺, and Cu²⁺ make this compound a useful chemosensor for Hg²⁺ detection in hydrophilic media. The sensor (6.0 × 10⁻⁶ M) displays significant fluorescence quenching upon addition of Hg²⁺ in pH 7.4 HEPES buffer without excimer formation. Job’s plot analysis shows the binding stoichiometry to be 2:1 (host/guest).     

All-plastic, disposable, low detection limit ion-selective electrodes

A novel concept for all-plastic and all-solid-state ion-selective electrodes (ISEs) is introduced. Planar, flexible ion-selective electrodes, comprising only polymeric materials, with no internal solution, were obtained. The cast conducting polymer layer (obtained from aqueous suspension) was covered with a solvent polymeric based membrane to obtain a planar all-plastic sensor. The conducting polymer layer served both as electrical contact and as ion-to-electron transducer. To illustrate this concept, the conducting polymer poly(3,4-ethylenedioxythiophene) doped with poly(4-styrenesulfonate) ions (PEDOT-PSS, Baytron P) was chosen. Due to interaction, analyte cations-poly(4-styrenesulfonate) anions, an extended linear range of potentiometric responses was obtained, with lowered detection limit.As example, Ca²⁺-selective and K⁺-selective all-plastic electrodes were fabricated and yielded with high selectivity, near Nernstian slopes and fast responses. The detection limits obtained for Ca²⁺- and K⁺-selective sensors were 5 × 10⁻⁹ M CaCl₂ and 4.4 × 10⁻⁷ M KCl, respectively.The possibilities of modifying the conducting polymer-phase composition is highlighted. This method is extremely useful to tune the desired type of responses, and cannot be directly applied for electrochemically deposited conducting polymers.     

Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.     

Immobilization of horseradish peroxidase to a nano-Au monolayer modified chitosan-entrapped carbon paste electrode for the detection of hydrogen peroxide

A procedure for fabricating an enzyme electrode has been described based on the effective immobilization of horseradish peroxidase (HRP) to a nano-scaled particulate gold (nano-Au) monolayer modified chitosan-entrapped carbon paste electrode (CCPE). The high affinity of chitosan entrapped in CCPE for nano-Au associated with its amino groups has been utilized to realize the use of nano-Au as an intermediator to retain high bioactivity of the enzyme. Hydrogen peroxide (H₂O₂) was determined in the presence of hydroquinone as a mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano-Au displayed excellent electrocatalytical activity to the reduction of H₂O₂. The effects of experimental variables such as the operating potential of the working electrode, mediator concentration and pH of measuring solution were investigated for optimum analytical performance by using an amperometric method. The enzyme electrode provided a linear response to hydrogen peroxide over a concentration range of 1.22×10⁻⁵-2.43×10⁻³ mol l⁻¹ with a sensitivity of 0.013 A l mol⁻¹ cm⁻² and a detection limit of 6.3 μmol l⁻¹ based on signal per noise =3. The apparent Michaelis-Menten constant (K_m^app) for the sensor was found to be 0.36 mmol l⁻¹. The lifetime, fabrication reproducibility and measurement repeatability were evaluated with satisfactory results. The analysis results of real sample by this sensor were in satisfactory agreement with those of the potassium permanganate titration method.     

Determination of calcium and total hardness in natural waters using a potentiometric sensor array

The determination of calcium and total hardness in natural waters is carried out with a potentiometric sensor array which consists of a series of ion-selective electrodes (ISEs) for Ca²⁺, Mg²⁺, NH₄⁺, K⁺, Na⁺, Li⁺, and H⁺. The selectivity of the calcium and magnesium ISEs is not fully achieved as other cation species may interfere with the analysis. The proposed sensor array device can overcome this drawback since it can take advantage of the cross-selectivities of cation species towards each ISE. In this approach, the multivariate data generated by the sensor array results in a richer source of analytical information which allows the quantification of calcium and total hardness in the water samples by means of chemometric methods. Results obtained are in reasonable concordance with those given by the standard method based on complexometry.     

Study and application of parallel catalytic hydrogen wave of lincomycin in the presence of persulfate

The polarographic currents of lincomycin in the absence and the presence of persulfate are studied by linear potential scan polarography and cyclic voltammetry. The reduction wave of lincomycin in phosphate buffer is a catalytic hydrogen wave, which is the reduction of the proton combined with lincomycin in nature. When S₂O₈²⁻ is present, the atomic hydrogen as intermediate product from the reduction of the combined proton is oxidized by both S₂O₈²⁻ and its reduction intermediate, sulfate radical anion SO₄⁻, to regenerate the original proton, producing the parallel catalytic hydrogen wave. Based on the parallel catalytic hydrogen wave, a novel method for the determination of lincomycin is proposed. In 0.48 mol l⁻¹ KH₂PO₄-Na₂HPO₄ (pH 7.4)-8.0×10⁻³ mol l⁻¹ K₂S₂O₈ supporting electrolyte, the peak potential of the parallel catalytic hydrogen wave is −1.82 V (vs. SCE). The second-order derivative peak current is rectilinear to the lincomycin concentration in the range of 8.5×10⁻⁸-9.0×10⁻⁵ mol l⁻¹ and the detection limit is 4×10⁻⁸ mol l⁻¹. The parallel catalytic hydrogen wave is three orders in magnitude higher than that of the corresponding catalytic hydrogen wave in analytical sensitivity. The proposed method is applied to the rapid determination of lincomycin hydrochloride in eye drops without previous separation.     

PVC-based bis(2-nitrophenyl)disulfide sensor for zinc ions

A PVC membrane electrode based on bis(2-nitrophenyl)disulfide carrier exhibits a very good response for Zn²⁺ in a wide concentration range (from 2.9×10⁻⁷ to 3.2×10⁻² mol l⁻¹) with a slope of 29.9±0.4 mV per decade of Zn²⁺ concentration. The response time of the sensor is about 10 s and the membrane can be used for more than 3 months without any observed divergence in potentials. The proposed sensor exhibits very good selectivity for Zn²⁺ over many cations and can be used in a wide pH range (2-9). This assembly served also as an indicator electrode in potentiometric titrations involving zinc ions and direct potentiometric determination of zinc ions in real and synthetic samples.     

Acid-base equilibria of phthalic acid in saline media: ion association from Pitzer equations

The protonation constants of 1,2-benzenedicarboxylic acid (phthalic acid) at 25 °C in NaCl and CaCl₂ (ionic strengths ranging from 0.1 to 2 mol kg⁻¹) were determined potentiometrically, and the results were analyzed by means of Pitzer equations. The values of the logarithm of the first and second dissociation constants ranged from 2.730 and 4.948 (in 0.101 mol kg⁻¹ NaCl) to 2.449 and 3.984 (in 0.624 mol kg⁻¹ CaCl₂), respectively. Tabulated interaction parameters for the inorganic species involved along with salting coefficients estimated from literature allowed the calculation of new interaction parameters for the phthalate-Na⁺/Ca²⁺ systems. The specific ion interaction model considered seems to account for the influence of the formation of weak complexes of phthalate with calcium ions on the equilibrium constants.     

Microflow injection chemiluminescence system with spiral microchannel for the determination of cisplatin in human serum

A new microflow injection chemiluminescence (μFI-CL) system was described for the determination of cisplatin in human serum. By using the microchip with double spiral channel configuration, the sensitivity was greatly enhanced due to more efficient mixing of the analyte and reagent solutions. Experimental results revealed that common ions in human serum, such as Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, Ni²⁺, Na⁺, K⁺, Ca²⁺, Cl⁻, NO₃⁻, Ac⁻, CO₃²⁻, PO₄³⁻, SO₄²⁻ did not cause interference with the detection of Pt(II) by using 1,10-phenanthroline as the masking agent. Under the optimized conditions, a linear calibration curve (R² = 0.998) over the range 2.0 × 10⁻⁸ to 2.0 × 10⁻⁶ mol L⁻¹ was obtained with the detection limit of 1.24 × 10⁻⁹ mol L⁻¹. The relative standard deviation was found to be 3.46% (n = 12) for 2.0 × 10⁻⁷ mol L⁻¹. The sample consumption was only 2 μL with the sample throughput of 72 h⁻¹. It had been used for trace platinum determination in cisplatin injection and human serum samples after the dosage of cisplatin. The recovery varied from 97.6 to 103.9%. The results proved that the proposed μFI-CL system had the advantages of high sensitivity and precision, low sample and reagents consumption, and high analytical throughput.     

Solid-state pH nanoelectrode based on polyaniline thin film electrodeposited onto ion-beam etched carbon fiber

An ultramicro pH sensor has been constructed based on a thin polyaniline film that was electrochemically deposited onto a carbon fiber nanometer-size electrode. The substrate nanoelectrodes were fabricated using ion-beam conically etched carbon fibers with tip diameters ranging ca. from 100 to 500 nm. The polyaniline film was deposited from HCl solution containing the aniline monomer by cycling the potential between −0.2 and +1.0 V. The electromotive force (emf) signal between the pH sensitive polyaniline-coated nanoelectrode and an Ag/AgCl reference electrode was linear over the pH range of 2.0-12.5 with a slightly super-Nernstian slope of ca. −60 mV/pH unit. Response times ranged from several sec at pHs around 7 up to 2 min at pH 12.5. The proposed pH nanoelectrode displayed high ion selectivity with respect to K⁺, Na⁺, Ca²⁺, and Li⁺, with log K_H,M values around −12 and has a working lifetime of about 20 days. Key parameters important for the pH nanoelectrode performance, including polyaniline film preparation, selectivity, response time, temperature dependence, relative coating thickness, stability, and reproducibility, have been characterized and optimized. The performance of the pH nanoelectrode was examined by measuring the pH of several real samples including body fluids (serum, urine) and low ionic strength water samples (rain, deionized and tap water). The results agreed very well with those obtained by using commercial glass pH electrodes. The proposed pH nanoelectrode demonstrated attractive properties and seems particularly promising for use under physiological conditions.     

Flow system with in-line separation/preconcentration coupled to graphite furnace atomic absorption spectrometry with W-Rh permanent modifier for copper determination in seawater

A flow system was coupled to a graphite furnace with a platform coated with tungsten-rhodium permanent chemical modifier for in-line separation and preconcentration of copper by employing a minicolumn loaded with 1-(2-tiazolylazo)-2-naphthol (TAN) immobilized on C₁₈-bonded silica fixed in the tip of the autosampler arm. Elution was made by sampling 35 μl of 0.50 mol l⁻¹ HCl with further delivering into a coated platform. Remarkable improvements in both selectivity and sensitivity were observed. Copper(II) was effectively separated from solutions containing up to 20 g l⁻¹ Na⁺; 10 g l⁻¹ K⁺, Ca²⁺ and Mg²⁺; 1.0 g l⁻¹ Fe³⁺ and Zn²⁺. For a sample flowing at 3.0 ml min⁻¹ and a loading of 60 s, the detection limit was estimated as 5 ng l⁻¹ Cu(II) at the 99.7% confidence level, and an enrichment factor of 33 was calculated. Coefficient of variation was estimated as 4% for a 0.30 μg l⁻¹ copper solution (n=20). The W-Rh permanent chemical modifier was used to improve system stability, analytical performance and atomizer lifetime. More than 1500 firings were carried out with the same atomizer without significant variations in sensitivity and precision. On account of the reagent immobilization, its consumption was lower than 0.2 μg per determination. In addition, TAN purification was unnecessary.     

Determination of noradrenaline and dopamine in pharmaceutical injection samples by inhibition flow injection electrochemiluminescence of ruthenium complexes

Two maximal potential-resolved flow injection-electrochemiluminescent (FI-ECL) peaks were observed for Ru(bpy)₃²⁺/TPrA system at 0.90 and 1.05 V, and for Ru(phen)₃²⁺/TPrA at 1.01 and 1.25 V (vs. Ag/AgCl) in pH 8.0 phosphate buffer solutions. Sensitive ECL inhibition effects were observed in the presence of noradrenaline and dopamine for both of these systems. Therefore, an FI-ECL inhibition method for determination of noradrenaline and dopamine has been developed. Under optimal conditions, linear responses between logarithm of ECL intensity changes and logarithm of sample concentration were found for noradrenaline in the linear range (LR) of 4×10⁻⁸-1×10⁻⁵ mol l⁻¹ with theoretical detection limit (DL) of 2.5×10⁻⁸ mol l⁻¹ for Ru(bpy)₃²⁺/TPrA system, and in LR of 2×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 7.1×10⁻⁹ mol l⁻¹ for Ru(phen)₃²⁺/TPrA system; and for dopamine in LR of 8×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 5.2×10⁻⁸ mol l⁻¹ for Ru(bpy)₃²⁺/TPrA system, in LR of 4×10⁻⁸-2×10⁻⁵ mol l⁻¹ with DL of 1.5×10⁻⁸ mol l⁻¹ for Ru(phen)₃²⁺/TPrA system. It was applied for determination of commercial pharmaceutical injection samples with satisfied results. The mechanism of the inhibition effects was proposed in the preliminary way.     

Voltammetric determination of mercury (II) in aqueous media using glassy carbon electrodes modified with novel calix[4]arene

A novel calix[4]arene derivative containing benzothiazole group was coated on glassy carbon electrode (GCE) and then applied to the recognition of mercury ion. Cyclic and square wave voltammetric results showed that the modified electrode selectively recognizes Hg²⁺ ion in aqueous media. A new anodic stripping peak at −0.3 V (vs. Ag/Ag⁺) can be obtained by scanning the potential from −0.6 to 0.6 V, and the peak currents are proportional to the Hg²⁺ concentration. The modified electrode in a 0.1 M H₂SO₄+0.01 M NaCl solution shows linear voltammetric response in the range of 25-300 μg l⁻¹ and detection limit of 5 μg l⁻¹ (ca. 2.5×10⁻⁸ M). This modified GCE does not present any significant interference from alkali, alkaline and transition metal ions except for Pb²⁺, Ag⁺ and Cu²⁺ ions. Only 500, 50 and 100-fold molar excess of Pb²⁺, Ag⁺ and Cu²⁺ ions, respectively, can lead to voltammetric response comparable with that of Hg²⁺. The proposed method was successfully applied to determine mercury in natural water.     

Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

A reversible chemosensor for nitrite based on the fluorescence quenching of a carbazole derivative

The carbazole derivative, with an amino group in 9-position (9-methylacryloylamino carbazole (MAC), has been utilized to prepare a fluorescent sensor and used for the determination of NO₂⁻ based on the reaction between nitrite (NO₂⁻) and excess I⁻ to form I₃⁻, which can quench the fluorescence of carbazole derivative. MAC, as a fluorescent carrier, has a terminal double bond and is covalently immobilized on a quartz glass plate surface by photo-polymerization to prevent the leakage of the dye. The sensor shows sufficient repeatability, selectivity, operational lifetime of 8 weeks, and a fast response of less then 30 s. NO₂⁻ can be determined in the range between 1.0×10⁻⁶ and 1.0×10⁻⁴ mol l⁻¹ with a detection limit of 8.0×10⁻⁷ mol l⁻¹ at pH of 2.0. The quenching mechanism is discussed. Most commonly coexisting ions do not interfer with the NO₂⁻ assay.     

Electrically induced fluorescence Fe sensing behavior of nanostructured Tiron doped polypyrrole

Nanostructured polypyrrole (PPy) film doped with Tiron was electrodeposited from aqueous solution on the surface of transparent electrode and used for sensitive, selective and rapid electrically controlled fluorescence detection of Fe³⁺ in aqueous media. The fluorescence intensity of PPy-Tiron film decreases linearly in the presence of Fe³⁺ by applying negative potential over a concentration range from 5.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹, with a relatively fast response time of less than 30 s at pH 7.4. The detection is not affected by the coexistence of other competitive metal ions such as Al³⁺, Ce³⁺, Tl³⁺, La³⁺, Bi³⁺, Cr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺, Pb²⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Sr²⁺ and Ba²⁺. The proposed electro-fluorescence sensor has a potential application to the determination of Fe³⁺ in environmental and biological systems. The fluorescent thin film sensor was also used as a novel probe for Fe³⁺/Fe²⁺ speciation in aqueous solution.     

Review of binding methods and detection of Al(III) binding events in trypsin and DL-DPPC liposomes by a general thermodynamic model

In this paper are reviewed some of the most useful binding formalisms which have been developed in order to investigate the diversity of the commonly encountered receptor-ligand systems. Particularly, our attention is focused on the presentation and application of a general and rigorous thermodynamic treatment which explains in a simple and coherent way the non-linear profiles observed in the experimental binding, Scatchard, Hill and Adair plots. By applying this model, both qualitative and detailed quantitative investigations were carried out on the binding process of Al(III) to trypsin and dl-dipalmitoylphosphatidylcholine (DPPC) liposomes. Particularly, it has been demonstrated that: Al(III) interacts with liposomes in two binding sites with very different dissociation constants. The first one has been calculated to be 0.0168 μmol l⁻¹ and the second 2.833 μmol l⁻¹. The first is referred to the preferential interaction of Al³⁺ with the polar head of the phospholipid, while the second most likely regards the interaction of Al³⁺ with other peripheral sites. On the other hand, Al³⁺ interacts with trypsin in two types of binding sites. The first binding site with K_1,1=0.2531 μmol l⁻¹ and the second with K_2,1=1.424 μmol l⁻¹.