A mercury(II) ion-selective electrode based on neutral salicylaldehyde thiosemicarbazone

A new ion-selective PVC membrane electrode based on salicylaldehyde thiosemicarbazone as an ionophore is developed successfully as sensor for mercury(II) ions. The electrode shows excellent potentiometric response characteristics and displays a linear log[Hg²⁺] versus EMF response over a wide concentration range of 1.778×10⁻⁶-1.0×10⁻¹ M with Nernstian slope of 29 mV per decade with the detection limit of 1.0×10⁻⁶ M. The response time of the electrode is less than 30 s and the membrane electrode operates well in the pH range of 1.0-3.0. The lifetime of the sensor is about 2 months. The electrode shows better selectivity towards Hg²⁺ ions in comparison with the alkali, alkaline and some heavy metal ions; most of these metal ions do not show significant interference (K^Pot_Hg,M values of the order of 10⁻³-10⁻⁴). The present sensor showed comparable or even better performance vis-à-vis similar PVC based ion-selective electrodes reported in literature. The sensor was also applied as an indicator electrode for potentiometric titration of Hg²⁺ions with I⁻ and Cr₂O₇²⁻.     

Improving the lower detection limit of potentiometric sensors by covalently binding the ionophore to a polymer backbone

The lower detection limit of polymeric membrane ion-selective electrodes (ISEs) is impaired by zero-current ion fluxes through the organic phase. This adverse effect is largely eliminated by covalently attaching the ionophore to a polymer backbone. To this purpose, the Pb²⁺-selective ligand, 4-tert-butylcalix[4] arene-tetrakis(N,N′-dimethylthioacetamide) is substituted on its upper rim by a diol derivative which is subsequently copolymerized with poly(tetrahydrofuran)diol and 2,2,4-trimethylhexamethylene diisocyanate to the corresponding polyurethane. By measurements on sandwich membranes, it is shown that through binding the ionophore to the polymer, the mobility of Pb²⁺ in the ISE membrane is strongly reduced. As a consequence, the response range of such an ISE is extended by several orders of magnitude. This is the case even when using an internal electrolyte that with an ISE based on a mobile ionophore leads to strong deviations from the linear response because of ion uptake from the sample into the membrane or ion release from the membrane into the sample. With a conventional inner filling solution of 10⁻¹ M Pb(NO₃)₂, a lower detection limit of 1.7×10⁻⁹ M Pb²⁺ has been achieved in the presence of 10⁻⁴ M Na⁺.     

A calixarene-based ion-selective electrode for thallium(I) detection

Three new calixarene Tl⁺ ionophores have been utilized in Tl⁺ ion-selective electrodes (ISEs) yielding Nernstian response in the concentration range of 10⁻²–10⁻⁶ M TlNO₃ with a non-optimized filling solution in a conventional liquid contact ISE configuration. The complex formation constants (log β_IL) for two of the calixarene derivatives with thallium(I) (i.e. 6.44 and 5.85) were measured using the sandwich membrane technique, with the other ionophore immeasurable due to eventual precipitation of the ionophore during these long-term experiments. Furthermore, the unbiased selectivity coefficients for these ionophores displayed excellent selectivity against Zn²⁺, Ca²⁺, Ba²⁺, Cu²⁺, Cd²⁺ and Al³⁺ with moderate selectivity against Pb²⁺, Li⁺, Na⁺, H⁺, K⁺, NH₄⁺ and Cs⁺, noting that silver was the only significant interferent with these calixarene-based ionophores. When optimizing the filling solution in a liquid contact ISE, it was possible to achieve a lower limit of detection of approximately 8 nM according to the IUPAC definition. Last, the new ionophores were also evaluated in four solid-contact (SC) designs leading to Nernstian response, with the best response noted with a SC electrode utilizing a gold substrate, a poly(3-octylthiophene) (POT) ion-to-electron transducer and a poly(methyl methacrylate)–poly(decyl methacrylate) (PMMA–PDMA) co-polymer membrane. This electrode exhibited a slope of 58.4 mV decade⁻¹ and a lower detection limit of 30.2 nM. Due to the presence of an undesirable water layer and/or leaching of redox mediator from the graphite redox buffered SC, a coated wire electrode on gold and graphite redox buffered SC yielded grossly inferior detection limits against the polypyrrole/PVC SC and POT/PMMA–PDMA SC ISEs that did not display signs of a water layer or leaching of SC ingredients into the membrane.     

The double K+/Ca2+ sensor based on laser scanned silicon transducer (LSST) for multi-component analysis

In the present work a double ion sensor based on a laser scanned semiconductor transducer (LSST) for the simultaneous determination of K⁺- and Ca²⁺-ions in solutions has been developed. Specially elaborated ion-sensitive membrane compositions based on valinomycin and calcium ionophore calcium bis[4-(1,1,3,3-tetramethylbutyl)phenyl] phosphate (t-HDOPP-Ca) were deposited as separate layers on a silanized surface of the Si/SiO₂/Si₃N₄-transducer. The proposed multi-sensor exhibits theoretical sensitivities and the detection limits of the sensor were found to be 2×10⁻⁶ mol l⁻¹ for K⁺ and 5×10⁻⁶ mol l⁻¹ for Ca²⁺. The elaborated double sensor is proposed for the first time as a prototype of a new type of multi-sensor systems for chemical analysis.     

Electrochemical Capacitive K+ EMIS Chemical Sensor Based on the Dibromoaza[7]helicene as an Ionophore for Potassium Ions Detection

A K⁺‐sensitive capacitive electrolyte‐membrane‐insulator‐semiconductor (EMIS) based on a novel dibromoaza[7]helicene ionophore has been developed. An ion‐sensitive membrane based on polyvinylchloride (PVC) doped with the ionophore was deposited on the Si₃N₄/SiO₂/Si‐p/Cu‐Al transducer. The properties of the K⁺‐EMIS chemical sensor were investigated by electrochemical impedance spectroscopy (EIS). All the developed devices upon being tested have shown good sensitivity and linearity responses within the range 10^?6 M to 10^?1 M of potassium activity, with good selectivity over a wide variety of other cations (Na⁺, Li⁺, Cu²⁺, Ca²⁺, and Mg²⁺). To our knowledge, this is the first time that a capacitive field‐effect sensor has been fabricated using helicene as a carrier for K⁺‐detection, combined with the structure: Si₃N₄/SiO₂/Si‐p/Cu‐Al as a transducer.     

Selective transport of zinc and copper ions by synthetic ionophores using liquid membrane technology

This work highlights the role of synthetic carrier (ionophore) in the separation of heavy metal ions. A new series of ionophores; 4,4′-nitrophenyl-azo-O,O′-phenyl-3,6,9-trioxaundecane-1,10-dioate (R₁), bis[4,4′nitro-phenylazo-naphthyl-(2,2-dioxydiethylether)] (R₂) 1,8-bis-(2-naphthyloxy)-3,6-dioxaoctane (R₃), 1,11-bis-(2-naphthyloxy)-3,6,9-trioxaunde-cane (R₄), 1,5-bis-(2-naphthyloxy)-3-oxa-pentane (R₅) have been synthesized and used as extractant as well as carrier for the transport of various metal ions (Na⁺, K⁺, Mg²⁺, Ni²⁺, Cu²⁺ and Zn²⁺) through liquid membranes. Effect of various parameters such as metal ion concentration, ionophore concentration, liquid–liquid extraction, back extraction, comparison of transport efficiency of BLM and SLM and different membrane support (hen’s egg shell and PTFE) have been studied. In BLM ionophores (R₂–R₅) transport Zn⁺ at greater extent and the observed trend for the transport of Zn²⁺ is R₂?>?R₄?>?R₃?>?R₅ respectively. Further transport efficiency is increased in SLM. In egg shell membrane ionophores (R₂–R₅) transport Zn⁺ due to their non-cyclic structure and pseudo cavity formation while ionophore R₁ transports Cu²⁺ ions at greater extent due to its cyclic structure and cavity size. Among the membrane support used egg shell membrane is found best for the transport of zinc ions because of its hydrophobic nature and exhibits electrostatic interactions between positively charged zinc ions and –COOH group of egg shell membrane. Thus structure of ionophores, hydrophobicity and porosity of the membrane support plays important role in separation of metal ions.     

A Lead‐Selective Membrane Electrode Based Upon a Phosphorylated Hexahomotrioxacalix[3]Arene

Solvent extraction of a mixture of Pb^II, Mn^II, Fe^III, Co^II, Ni^II and Cd^II in aqueous perchlorate medium by a phosphorylated hexahomotrioxacalix[3]arene (calix‐3) in dichloromethane shows a significant selectivity towards lead ions. The ligand can also be incorporated into a membrane to provide a new lead ion‐selective electrode (Pb^II‐ISE). A plasticized PVC membrane containing 30% PVC, 53.5% ortho‐nitrophenyloctylether (NPOE), 4.5% sodium tetraphenylborate (NaTPB) and 12% ionophore was directly coated on a graphite rod. This sensor gave a good Nernstian response of 29.7 ± 0.7 mV decade^?1 over a concentration range of 1 × 10^?8 – 1 × 10^?4 M of lead ions, independent of pH in the range 3‐7, with a detection limit of 0.4 × 10^?8 M. The dynamic response time of the electrode to achieve a steady potential was very fast and found to be less than 7 s. The selectivity relative to Ag⁺, NH₄⁺, Li⁺, Na⁺, K⁺, Ca²⁺, Sr²⁺, Ba²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Fe³⁺, La³⁺, Sm³⁺, Dy³⁺, Er³⁺, Y³⁺ and Th⁴⁺ was examined. The electrode exhibits adequate stability with good reproducibility (with a slope of 29.6 ± 1.5 mV for 8 weeks). The characteristics of the sensor are compared with those of a tetraphosphorylated calix[4]arene (calix‐4) based Pb^II‐ISE, reported recently. The electrode was successfully used as an indicator electrode for a potentiometric titration of a lead solution using a standard solution of EDTA. The applicability of the sensor for lead ion measurements in various synthetic samples was also investigated.     

Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.     

Ultra-sensitive determination of cyanide in surface water by gas chromatography–tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography–tandem mass spectrometric (GC–MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L⁻¹ of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60 °C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC–MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L⁻¹ and 0.07 μg L⁻¹ in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y = 0.7140x + 0.1997 and r² = 0.9963 (for a working range of 0.07–10 μg L⁻¹) and the accuracy was in a range of 98–102%; the precision of the assay was less than 7% in surface water. The common ions Cl⁻, F⁻, Br⁻, NO₃⁻, SO₄²⁻, PO₄³⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺, Fe²⁺ and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07–0.11 μg L⁻¹ in 6 of 10 surface water samples.     

Manganese (II) selective PVC based membrane sensor using a Schiff base

N,N′,N″,N′′′-1,5,8,12-tetraazadodecane-bis(salicylaldiminato)(H₂L) has been used as ionophore for preparing Mn²⁺ selective sensor. Membranes of different composition with regard to ratio of H₂L:PVC:NPOE:NaTPB have been prepared and investigated. The best performance was obtained with the membrane of composition 10:150:150:10 (H₂L:PVC:NPOE:NaTPB) (w/w; mg). This membrane generated linear potential response in the concentration range of 5.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a Nernstian slope of 30.0 mV/decade of activity and fast response time (10 s). Hydrogen ion does not effect to the performance of sensor in the pH range 3.0-6.5. The sensor was found to be sufficient selective for Mn²⁺ over a number of alkali, alkaline and heavy metal ions and could therefore be used for the determination of manganese in various samples by direct potentiometry.     

A Coated Graphite Thorium‐Ion Selective Potentiometric Sensor Based on a Calix[4]arene Bearing Phosphoryl Groups

5,11,17,23‐Tetra‐tert‐butyl‐25,26,27,28‐tetrakis(diphenylphosphinoylmethoxy)calix[4]arene ( 1 )has been used for the preparation of a graphite coated thorium ion‐selective electrode (Th⁴⁺‐ISE). The plasticized PVC membrane containing 30% PVC, 58% ortho‐nitrophenyloctylether (NPOE), 4% sodium tetraphenylborate (NaTPB) and 8% ionophore was directly coated on a graphite rod. This sensor gave good Nernstian responses with a slope of 15.5 ± 0.1 mV/decade over a concentration range of 1 × 10^?5 ?1 × 10^?3 M of thorium ions with a limit of detection of 7.9 × 10^?6 M. The dynamic response time of the electrode to achieve a steady potential was found to be about 15 seconds. The potential of the prepared sensor was independent of the pH variation in the range 2.3–4.0. The selectivity relative to several mono‐, di‐ and tri‐valent metal ions, i.e. Li⁺, Na⁺, K⁺, Ag⁺, NH₄⁺, Sr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, La³⁺, Sm³⁺, Dy³⁺, Er³⁺ and Y³⁺ was examined. This electrode can be used for 6 months without any considerable divergences in the potential response. The sensor was successfully used as an indicator electrode for the potentiometric titration of a thorium solution using a standard solution of EDTA.     

A cerium(III) selective polyvinyl chloride membrane sensor based on a Schiff base complex of N,N'-bis[2-(salicylideneamino)ethyl]ethane-1,2-diamine

A polyvinyl chloride (PVC) based membrane sensor for cerium ions was prepared by employing N,N′-bis[2-(salicylideneamino)ethyl]ethane-1,2-diamine as an ionophore, oleic acid (OA) as anion excluder and o-nitrophenyloctyl ether (o-NPOE) as plasticizer. The plasticized membrane sensor exhibits a Nernstian response for Ce(III) ions over a wide concentration range (1.41 × 10⁻⁷ to 1.0 × 10⁻² M) with a limit of detection as low as 8.91 × 10⁻⁸ M. It has a fast response time (<10 s) and can be used for 4 months. The sensor revealed a very good selectivity with respect to common alkali, alkaline earth and heavy metal ions. The response of the proposed sensor is independent of pH between 3.0 and 8.0. It was used as an indicator electrode in potentiometric titration of fluoride, carbonate and oxalate anions and determination of cerium in simulated mixtures.     

All Solid State Chromium(III) Selective Potentiometric Sensor Based on 2‐(1‐(2‐((3‐(2‐Hydroxyphenyl)‐1H‐pyrozol‐1‐yl)methyl)benzyl)‐1H‐pyrazol‐3‐yl)phenol

Highly selective all solid state electrochemical sensor based on a synthesized compound i.e. 2‐(1‐(2‐((3‐(2‐hydroxyphenyl)‐1H‐pyrozol‐1‐yl)methyl)benzyl)‐1H‐pyrazol‐3‐yl)phenol (I) as an ionophore has been prepared and investigated for the selective quantification of chromium(III) ions. The effect of various plasticizers, viz. dibutyl phosphonate (DBP), dibutyl(butyl) phosphonate (DBBP), nitrophenyl octyl ether (NPOE), tris‐(2‐ethylhexyl)phosphonate (TEP), tri‐butyl phosphonate (TBP), dioctyl phthalate (DOP), dioctyl sebacate (DOS), benzyl acetate (BA) and acetophenone (AP) along with anion excluders NaTPB (sodium tetraphenyl borate) and KClTPB (potassium(tetrakis‐4‐chlorophenyl)borate was also studied. The optimum composition of the best performing membrane contained (I):KClTPB:NPOE:PVC in the ratio 15 : 3 : 40 : 42 w/w. The sensor exhibited near Nernstian slope of 20.1±0.2 mV/decade of activity in the working concentration range of 1.2×10^?7–1.0×10^?1 M, and in a pH range of 3.8–4.5. The sensor exhibited a fast response time of 10 s and could be used for about 5 months without any considerable divergence in potentials. The proposed sensor showed very good selectivity over most of the common cations including Na⁺, Li⁺, K⁺, Cu²⁺, Sr²⁺, Ni²⁺, Co²⁺, Ba²⁺, Hg²⁺, Pb²⁺, Zn²⁺, Cs⁺, Mg²⁺, Cd²⁺, Al³⁺, Fe³⁺and La³⁺. The activity of Cr(III) ions was successfully determined in the industrial waste samples by using this sensor.     

Calix[2]furano[2]pyrrole and related compounds as the neutral carrier in silver ion-selective electrode

The performance of calix[2]furano[2]pyrrole and related compounds used as neutral carriers for silver selective polymeric membrane electrode was investigated. The silver ion-selective electrode based on calix[2]furano[2]pyrroles gave a good Nernstian response of 57.1 mV per decade for silver ion in the activity range 1×10⁻⁶ to 1×10⁻² M. The present silver ion-selective electrode displayed very good selectivity for Ag⁺ ion against alkali and alkaline earth metal ions, NH₄⁺, and H⁺. In particular, the present Ag⁺-selective electrode exhibited very low responses towards Hg²⁺ and Pb²⁺ ions. The potentiometric selectivity coefficients of the silver ion-selective electrode exhibited a strong dependence on the solution pH. In particular, the response of the electrode to the Hg²⁺ activity was greatly diminished at pH 2.5 compared to that at pH 5.0. Overall, the performance of the present silver ion-selective electrode based on the ionophore, calix[2]furano[2]pyrrole, is very comparable to that of the electrode prepared with the commercially available neutral carrier in terms of slope, linear range, and detection limits.     

Gallium(III) selective sensors based on 2-amino-3-(α-N-phenylmethyl-2′-amino-1′,4′-naphthoquinonyl)-1,4 naphthoquinones in poly (vinyl chloride)

Synthesis and application of 2-amino-3-(α-N-phenylmethyl-2′-amino-1′,4′-naphthoquinonyl)-1,4 naphthoquinone (S) as a neutral ionophore for the determination of gallium(III) in PVC-based membrane sensors has been described. The sensor based on membrane composition (w/w, mg%); 5.0 (S):30.0 (PVC):5.0 (KTpClPB):60.0 (o-NPOE) is the best and showed a working range of 2.3 × 10⁻⁷ to 1.0 × 10⁻² M with detection limit of 1.2 × 10⁻⁷ M. It can tolerate non-aqueous media up to 15% with a slope of 19.7 mV decade⁻¹ of activity. The sensor has been used to assess the Ga(III) concentration in different natural samples (peach and tomato leaves, coal-fly-ash and river sediments). It can be used for 2.5 months without any distortion in results, after which, leaching of ionophore was observed from the membrane phase. The proposed sensor has shown a good dynamic response time of 11 s.     

Sensitive and robotic determination of bromate in sea water and drinking deep-sea water by headspace solid-phase micro extraction and gas chromatography–mass spectrometry

A robotic method has been established for the determination of bromate in sea water and drinking deep-sea water. Bromate in water was converted into volatile derivative, which was measured with headspace solid-phase micro extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). Derivatization reagent and the HS-SPME parameters (selection of fibre, extraction/derivatization temperature, heating time and; the morality of HCl) were optimized and selected. Under the established conditions, the detection and the quantification limits were 0.016 μg L⁻¹ and 0.051 μg L⁻¹, respectively, and the intra- and inter-day relative standard deviation was less than 7% at concentrations of 1.0 and 10.0 μg L⁻¹. The calibration curve showed good linearity with r² = 0.9998. The common ions Cl⁻, NO₃⁻, SO₄²⁻, HPO₄²⁻, H₂PO₄⁻, K⁺, Na⁺, NH₄⁺, Ca²⁺, Mg²⁺, Ba²⁺, Mn⁴⁺, Mn²⁺, Fe³⁺ and Fe²⁺ did not interfere even when present in 1000-fold excess over the active species. The method was successfully applied to the determination of bromate in sea water and drinking deep-sea water.     

Luminescence enhancement of Eu, Ce co-doped Ba3Si5O13−δNδ phosphors

Host lattice Ba₃Si₅O_13−δN_δ oxonitridosilicates have been synthesized by the traditional solid state reaction method. The lattice structure is based on layers of vertex-linked SiO₄ tetrahedrons and Ba²⁺ ions, where each Ba²⁺ ion is coordinated by eight oxygen atoms forming distorted square antiprisms. Under an excitation wavelength of 365 nm, Ba₃Si₅O_13−δN_δ:Eu²⁺ and Ba₃Si₅O_13−δN_δ:Eu²⁺,Ce³⁺ show broad emission bands from about 400-620 nm, with maxima at about 480 nm and half-peak width of around 130 nm. The emission intensity is strongly enhanced by co-doping Ce³⁺ ions into the Ba₃Si₅O_13−δN_δ:Eu²⁺ phosphor, which could be explained by energy transfer. The excitation band from the near UV to the blue light region confirms the possibility that Ba₃Si₅O_13−δN_δ:Eu²⁺, Ce³⁺ could be used as a phosphor for white LEDs.     

Simultaneous determination of Mn(II), Cu(II) and Fe(III) as 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol complexes by adsorptive cathodic stripping voltammetry at a carbon paste electrode

A simple and precise square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV) method has been described for simultaneous determination of Mn(II), Cu(II) and Fe(III) in water samples using a carbon paste electrode. In 0.1 mol L⁻¹ acetate buffer (pH 5) containing 50 μmol L⁻¹ of 2-(5′-bromo-2′-pyridylazo)-5-diethylaminophenol (5-Br-PADAP), Mn(II), Cu(II) and Fe(III) were simultaneously determined as metal-complexes with 5-Br-PADAP following preconcentration onto the carbon paste electrode by adsorptive accumulation at +1.0 V (vs. Ag/AgCl/3 M KCl). Insignificant interference from various cations (K⁺, Na⁺, Mg²⁺, Ca²⁺, Al³⁺, Bi³⁺, Sb³⁺, Se⁴⁺, Zn²⁺, Ni²⁺, Co²⁺, Cd²⁺, Pb²⁺, V⁵⁺, Ti⁴⁺ and NH₄⁺), anions (HCO₃⁻, Cl⁻, NO³⁻, SO₄²⁻ and PO₄³⁻) and ascorbic acid was noticed. Limits of detection of 0.066, 0.108 and 0.093 μg L⁻¹ and limits of quantitation of 0.22, 0.36 and 0.31 μg L⁻¹ Mn(II), Cu(II) and Fe(III), respectively, were achieved by the described method. The described stripping voltammetry method was successfully applied for simultaneous determination of Mn(II), Cu(II) and Fe(III) in ground, tap and bottled natural water samples.     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

Electrically induced fluorescence Fe sensing behavior of nanostructured Tiron doped polypyrrole

Nanostructured polypyrrole (PPy) film doped with Tiron was electrodeposited from aqueous solution on the surface of transparent electrode and used for sensitive, selective and rapid electrically controlled fluorescence detection of Fe³⁺ in aqueous media. The fluorescence intensity of PPy-Tiron film decreases linearly in the presence of Fe³⁺ by applying negative potential over a concentration range from 5.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹, with a relatively fast response time of less than 30 s at pH 7.4. The detection is not affected by the coexistence of other competitive metal ions such as Al³⁺, Ce³⁺, Tl³⁺, La³⁺, Bi³⁺, Cr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺, Pb²⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Sr²⁺ and Ba²⁺. The proposed electro-fluorescence sensor has a potential application to the determination of Fe³⁺ in environmental and biological systems. The fluorescent thin film sensor was also used as a novel probe for Fe³⁺/Fe²⁺ speciation in aqueous solution.