Determination of total inorganic arsenic in water using on-line pre-concentration and hydride-generation atomic absorption spectrometry

A rapid and sensitive method for the on-line separation and pre-concentration of inorganic arsenic in water samples is described. The analyte in the pentavalent oxidation state is reduced to its trivalent form with l-cysteine and the total inorganic arsenic is sorbed onto activated alumina in the acid form in a mini-column coupled to a FI-HG AAS system. Afterwards, it is eluted with 3 mol l⁻¹ HCl. An enrichment factor of 7 was obtained, allowing an analytical flow rate of about 28 determinations per hour. The limits of detection (3σ) and of quantification (10σ) were calculated as LOD = 0.15 μg l⁻¹ of As and LOQ = 0.5 μg l⁻¹ of As, respectively. Relative standard deviations (n = 10) less than 8% were obtained for different arsenic concentrations and the accuracy was verified by analysing certified reference materials. Different kinds of samples, such as mineral water, drinking water, river water and natural spring water were analyzed and good agreement was obtained with the values from spiked experiments.     

AE-HG-AFS测定长期汞暴露人群补硒后尿中硒的形态

建立了一种利用阴离子交换高效液相色谱与氢化物发生原子荧光光谱联用同时测定四、六价硒及硒代半胱氨酸(SeCys)形态的方法。优化了六价硒的还原条件及仪器检测参数,以不同浓度的柠檬酸铵作为流动相,在10 min内同时分离了四、六价硒及硒代半胱氨酸(SeCys)。采用加标法定量,加标回收率在90%～119%之间,相对标准偏差为1.6%～3.1%(100μg/L),四、六价硒及硒代半胱氨酸(SeCys)的检出限分别为0.32μg/L、0.47μg/L和0.44μg/L(进样量为100μL)。应用该法对长期汞暴露人群补硒后尿中的小分子硒的形态进行了分析,仅检测到硒代半胱氨酸(SeCys)。     

Arsenic speciation in natural water samples by coprecipitation-hydride generation atomic absorption spectrometry combination

A speciation procedure for As(III) and As(V) ions in environmental samples has been presented. As(V) was quantitatively recovered on aluminum hydroxide precipitate. After oxidation of As(III) by using dilute KMnO₄, the developed coprecipitation was applied to determination of total arsenic. Arsenic(III) was calculated as the difference between the total arsenic content and As(V) content. The determination of arsenic levels was performed by hydride generation atomic absorption spectrometry (HG-AAS). The analytical conditions for the quantitative recoveries of As(V) including pH, amount of aluminum as carrier element and sample volume, etc. on the presented coprecipitation system were investigated. The effects of some alkaline, earth alkaline, metal ions and also some anions were also examined. Preconcentration factor was calculated as 25. The detection limits (LOD) based on three times sigma of the blank (N: 21) for As(V) was 0.012 μg L⁻¹. The satisfactory results for the analysis of arsenic in NIST SRM 2711 Montana soil and LGC 6010 Hard drinking water certified reference materials for the validation of the method was obtained. The presented procedure was successfully applied to real samples including natural waters for arsenic speciation.     

Determination and speciation of selenium in water samples collected from Muğla (Turkey) province by hydride generation atomic absorption spectrometry

In this work, determination of selenium in various water samples was done by using hydride generation atomic absorption spectrometry. The most appropriate values of HCl concentration, NaBH₄ concentration, NaOH concentration, flow rate of argon and flow rate of waste solution were determined. The optimum concentration of the HCl, NaBH₄ and NaOH solutions were found to be 7.0 mol L^?1, 1.0% and 0.75%, respectively. The optimum flow rate of Ar gas and waste solution were also found to be 100.9 mL min^?1 and 4.0 mL min^?1, respectively. Values of LOD and LOQ were calculated separately for total Se and Se(IV). LOD and LOQ values were calculated 0.56 μg L^?1, 1.87 μg L^?1 for total Se and 0.72 μg L^?1, 2.40 μg L^?1 for Se(IV), respectively. The precision was evaluated by relative standard deviation (RSD%) was found to be 3.5% for total Se and 3.1% for Se(IV) (n = 11). A standard reference material (NIST 1643e) was used in order to check the accuracy of the proposed method. There was a good agreement between certified and found values for standard reference material. The method was applied to the analysis of total Se and Se(IV) concentrations in tap water samples collected from the various regions of Mu?la. Proposed method showed spike recovery ranges from 92% to 116% in water samples.     

Determination of selenium using atomically imprinted polymer (AIP) and hydride generation atomic absorption spectrometry

This paper describes selenium determination based on Se⁰ preconcentration in the imprinted polymer (synthesized with 2.25 mmol SeO₂, 4-vinylpyridine and 1-vinylimidazole) with subsequent detection on-line in HG-FAAS. During the synthesis, SeO₂ is reduced to Se (0). Therefore, there are no MIP neither IIP in the present work, thus we denominated: AIP, i.e., atomically imprinted polymers. For the optimization of analytical parameters Doehlert design was used. The method presented limit of detection and limit of quantification of 53 and 177 ng L⁻¹, respectively, and linear range from 0.17 up to 6 μg L⁻¹ (r = 0.9936). The preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 232; 0.06 mL and 58 min⁻¹ respectively. The proposed method was successfully applied to determine Se in Brazil nuts (0.33 ± 0.03 mg kg⁻¹), apricot (0.46 ± 0.02 mg kg⁻¹), white bean (0.47 ± 0.03 mg kg⁻¹), rice flour (0.47 ± 0.02 mg kg⁻¹) and milk powder (0.22 ± 0.01 mg kg⁻¹) samples. It was possible to do 12 analyzes per hour. Accuracy was checked and confirmed by analyzing certified reference material (DORM-2, dogfish muscle), and samples precision was satisfactory with RSD lower than 10%.     

流通式电化学氢化物发生法原子吸收测定硒的研究

采用自行研制的以铅作阴极、石墨作阳极无隔膜分隔的流通式电化学氢化物发生器,电解产生的气体经气液分离器后直接送入火焰原子吸收进行测定,因无外加载气减少了稀释提高了灵敏度。研究了各种影响因素,选择了最佳条件,以0．5mol／L硫酸作电解液,以1．3mL／min流速通过氢化物发生器,电解电流为2．0A。结果表明硒质量浓度在0～5μg／mL范围内呈良好的线性关系,其相关系数为0．9988,相对标准偏差为4．4％,特征质量浓度为0．0397μg／mL,检出限为0．084μg／mL。     

Oxidation State Specific Generation of Arsines from Methylated Arsenicals Based on L- Cysteine Treatment in Buffered Media for Speciation Analysis by Hydride Generation - Automated Cryotrapping - Gas Chromatography-Atomic Absorption Spectrometry with the Multiatomizer

An automated system for hydride generation - cryotrapping- gas chromatography - atomic absorption spectrometry with the multiatomizer is described. Arsines are preconcentrated and separated in a Chromosorb filled U-tube. An automated cryotrapping unit, employing nitrogen gas formed upon heating in the detection phase for the displacement of the cooling liquid nitrogen, has been developed. The conditions for separation of arsines in a Chromosorb filled U-tube have been optimized. A complete separation of signals from arsine, methylarsine, dimethylarsine, and trimethylarsine has been achieved within a 60 s reading window. The limits of detection for methylated arsenicals tested were 4 ng l(-1). Selective hydride generation is applied for the oxidation state specific speciation analysis of inorganic and methylated arsenicals. The arsines are generated either exclusively from trivalent or from both tri- and pentavalent inorganic and methylated arsenicals depending on the presence of L-cysteine as a prereductant and/or reaction modifier. A TRIS buffer reaction medium is proposed to overcome narrow optimum concentration range observed for the L-cysteine modified reaction in HCl medium. The system provides uniform peak area sensitivity for all As species. Consequently, the calibration with a single form of As is possible. This method permits a high-throughput speciation analysis of metabolites of inorganic arsenic in relatively complex biological matrices such as cell culture systems without sample pretreatment, thus preserving the distribution of tri- and pentavalent species.     

Determination of selenomethionine by high performance liquid chromatography-direct hydride generation-atomic absorption spectrometry

A simple, reliable, trace determination of selenomethionine (Semet) based on a direct hydride generation atomic absorption spectrometric method was developed using sodium tetrahydroborate (0.3% in 0.2% NaOH) and hydrochloric acid (3 M). The method excluded any chemical pretreatment prior to hydride generation (HG). The optimized HG system was successfully coupled with the HPLC system. The detection limit (3σ of blank; n=5), reproducibility (R.S.D. of three successive analyses/day, performed on three different days), and repeatability (R.S.D. of three successive analyses) of the method were 1.08 ng ml⁻¹, 9.8% for 9.04 ng ml⁻¹ and 2.1–9.5% for 30.0–1.27 ng ml⁻¹ Semet as Se (standards prepared in Milli-Q water). Calibration graph was linear up to 30 ng ml⁻¹. This HPLC-HG-AAS method is very promising and successfully determined Semet (spiked) in human urine.     

Monitoring of selenium in water samples using dispersive liquid-liquid microextraction followed by iridium-modified tube graphite furnace atomic absorption spectrometry

A simple and powerful microextraction technique was used for determination of selenium in water samples using dispersive liquid-liquid microextraction (DLLME) followed by graphite furnace atomic absorption spectrometry (GF AAS). DLLME and simultaneous complex formation was performed with rapid injection of a mixture containing ethanol (disperser solvent), carbon tetrachloride (extraction solvent) and ammonium pyrrolidine dithiocarbamate (APDC, chelating agent) into water sample spiked with selenium. After centrifuging, fine droplets of carbon tetrachloride, which were dispersed among the solution and extracted Se-APDC complex, sediment at the bottom of the conical test tube. The concentration of enriched analyte in the sedimented phase was determined by iridium-modified pyrolitic tube graphite furnace atomic absorption spectrometry. The concentration of selenate was obtained as the difference between the concentration of selenite after and before pre-reduction of selenate to selenite. Some effective parameters on extraction and complex formation, such as extraction and disperser solvent type and their volume, extraction time, salt effect, pH and concentration of chelating agent were optimized. Under the optimum conditions, the enrichment factor of 70 was obtained from only 5.00 mL of water sample. The calibration graph was linear in the range of 0.1-3 μg L^− 1 with detection limit of 0.05 μg L^− 1. The relative standard deviation (RSDs) for ten replicate measurements of 2.00 μg L^− 1 of selenium was 4.5%. The relative recoveries of selenium in tap, river and sea water samples at spiking level of 2.00 μg L^− 1 were 106, 96 and 98%, respectively.     

Determination of arsenic(III) and total inorganic arsenic in water samples using an on-line sequential insertion system and hydride generation atomic absorption spectrometry

A simple and robust on-line sequential insertion system coupled with hydride generation atomic absorption spectrometry (HG-AAS) was developed, for selective As(III) and total inorganic arsenic determination without pre-reduction step. The proposed manifold, which is employing an integrated reaction chamber/gas-liquid separator (RC-GLS), is characterized by the ability of the successful managing of variable sample volumes (up to 25 ml), in order to achieve high sensitivity. Arsine is able to be selectively generated either from inorganic As(III) or from total arsenic, using different concentrations of HCl and NaBH₄ solutions. For 8 ml sample volume consumption, the sampling frequency is 40 h⁻¹. The detection limit is c_L = 0.1 and 0.06 μg l⁻¹ for As(III) and total arsenic, respectively. The precision (relative standard deviation) at 2.0 μg l⁻¹ (n = 10) level is s_r = 2.9 and 3.1% for As(III) and total arsenic, respectively. The performance of the proposed method was evaluated by analyzing the certified reference material NIST CRM 1643d and spiked water samples with various concentration ratios of As(III) to As(V). The method was applied for arsenic speciation in natural waters samples.     

Separation and speciation of selenium in food and water samples by the combination of magnesium hydroxide coprecipitation-graphite furnace atomic absorption spectrometric determination

A simple and economic separation and speciation procedure for selenium in food and water samples have been presented prior to its graphite furnace atomic absorption spectrometry (GFAAS). Magnesium hydroxide coprecipitation system for selenium(IV) was applied to the separation and speciation of selenium ions. The influences of the various analytical parameters for the quantitative recoveries of selenium ions like pH, amounts of magnesium ions as carrier elements, etc. on were examined. The effects of the alkaline and earth alkaline metals, some transition metals and some anions on the recoveries of selenium(IV) were also investigated. The recoveries of analytes were found greater than 95%. No appreciable matrix effects were observed. The detection limit, defined as three times the blank standard deviation (3σ), was 0.030 μg l⁻¹. The preconcentration factor for the presented system was 25. The proposed method was applied to the speciation of selenium(IV), selenium(VI) and determination of total selenium in natural waters and microwave digested various food samples with satisfactory results. The procedure was validated with certified reference materials. The relative errors and relative standard deviations were below 6% and 10%, respectively.     

Flow injection-hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth

A simple and robust flow injection system which permits low sample and reagent consumption is described for rapid and reliable hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth. The system, which composed of one peristaltic pump and one four channel solenoid valve, used water as the carrier streams for both sample and NaBH₄ solution. Rapid off-line pre-reduction of the analytes was achieved by using hydroxylamine hydrochloride for selenium and a mixture of potassium iodide and ascorbic acid for arsenic and bismuth. Transition metal interference was eliminated with the addition of thiourea and EDTA into the NaBH₄ solution and significant sensitivity enhancement was observed for selenium in the presence of thiourea in the reductant solution. Under optimised conditions, the method achieved detection limits of 0.2 ng mL⁻¹ for Se, 0.5 ng mL⁻¹ for As and 0.3 ng mL⁻¹ for Bi. The method was very reproducible, achieving relative standard deviations of 6.3% for Se, 3.6% for As and 4.7% for Bi, and has a sample throughput of 360 h⁻¹. Successful application of the method to the quantification of selenium, arsenic and bismuth in a certified reference river sediment sample is reported.     

Masking agents in the determination of selenium by hydride generation technique

The effects of several masking agents in the determination of selenium by hydride generation was studied using a continuous flow hydride generator coupled with atomic absorption spectrometry. A miniature argon hydrogen diffusion flame was employed as the atomizer. The effects of masking agents (KI, NaSCN, thiourea, -cysteine, 1,1,3,3 tetramethyl-2-thiourea) were studied both in the absence and in the presence of selected interfering species (Cu, Ag, Au, Ni, Co, Pd, Pt and Fe) and using different addition strategies of the masking agents to the reaction system: in batch mode, either to sample or NaBH₄ reducing solution; in on-line mode, to the sample either before or after the HG step). The combined effect of some masking agents was also investigated. The addition mode of the masking agent to the reaction system could play a decisive role in the control of interfering processes both in the absence and in the presence of concomitants. The addition of NaSCN to the reducing solution of NaBH₄ produced a moderate catalytic effect, similar to the one obtained in the presence of KI, and improved the tolerance limits for Cu, Ni, Co and Pd. Linearity of calibration graphs was unaffected by the on-line addition of 1,1,3,3 tetramethyl-2-thiourea to sample solution, while under similar conditions thiourea produced dramatic curvature of calibration graphs. The combined use of KI (added to reducing solution) and 1,1,3,3 tetramethyl -2-thiourea (added on-line to the sample) exhibited masking properties comparable but not superior to those of thiourea, except for Pt and Pd for which good tolerance limits were achieved. In the absence of KI in the reductant solution the masking efficiency of 1,1,3,3 tetramethyl-2-thiourea was considerably lowered. The addition of some masking agents such as thiourea, -cysteine and 1,1,3,3 tetramethyl thiourea on-line to reaction solution after the NaBH₄+KI reduction step, could be highly effective in the control of Cu and Ag interferences. The method was applied to determination of trace of selenium in pure copper standard reference materials.     

Development of an on-line UV decomposition system for direct coupling of liquid chromatography to atomic-fluorescence spectrometry for selenium speciation analysis

Speciation analysis of four selenium species (selenite, selenate, selenocystine, and selenomethionine) has been performed by on-line coupling of liquid chromatography (LC), UV decomposition, hydride generation (HG), and atomic-fluorescence spectrometry (AFS). Because only selenite (Se^IV) can generate hydrides, on-line conversion of organic and inorganic selenium species is discussed. Preliminary study showed that the use of only UV light was not sufficient to reduce selenate, because no absorption is observed for this compound at the main wavelength of the low-pressure mercury lamp (253.7 nm). Thus, new conditions based on addition of a reducing reagent (I⁻) were developed. Mechanisms of action are proposed to explain selenium species conversions. Because of their compatibility with on-line treatment, phosphate buffers were used for chromatographic separation on an anion exchange column (Hamilton PRP-X100). Detection limits (19–60 pg Se) and repeatability of the technique were close to those obtained by conventional quadrupole ICPMS. Applications to real samples such as water and oysters are presented and emphasize the robustness of the system.     

Optimization of selenium determination in plant samples by hydride generation and axial view inductively coupled plasma atomic emission spectrometry

The use of hydride generation coupled with axial view inductively couple plasma atomic emission spectrometry was presented for the determination of selenium in plant samples. The chemical factors affecting potentially the hydride generation efficiency (hydrochloric acid, sodium borohydride and sodium hydroxide concentrations) were assessed through investigation of chemical interference, accuracy and repeatability. The accuracy of measurements was not affected by elements present in high concentration in the plant matrix (K, Ca, Mg, and P). No interference was also observed with transition metals. Using a real sample (maize) with standard additions, decreases of recoveries were sometimes observed for 0.1% (m/v) NaOH, and attained 13.8% in the most unfavourable case. The final accuracy of the method was verified by using two certified reference materials: CRM 402 (white clover) and CRM 279 (sea lettuce). No statistically significant differences were obtained between the measured concentrations and the certified values. The optimized method was found sensitive (detection limit 0.15 μg l⁻¹), reliable and repeatable (R.S.D. between 1.3% and 4.0%).     

Determination of selenite and selenate in drinking water: a fully automatic on-line separation/pre-concentration system coupled to electrothermal atomic spectrometry with permanent chemical modifiers

A time-based flow injection (FI) separation pre-concentration system coupled to an electrothermal atomic absorption spectrometer (graphite furnace) has been developed for the direct ultra-trace determination of selenite and selenate in drinking water. The pre-concentration of both forms of selenium is carried out onto a micro-column packed with an anionic resin (Dowex 1X8) that is placed in the robotic arm of the autosampling device. Selenite and selenate are sequentially eluted with HCl 0.1 M and HCl 4 M, respectively. The interference of large quantities of chloride during selenium atomisation is prevented by using iridium as a “permanent” chemical modifier. The features of the pre-concentration separation system for both species are: 53% efficiency of retention and an enhancement factor of 82 for a pre-concentration time of 180 s (sample flow rate=3 ml min⁻¹) with HCl elution volumes of 100 μl. The detection limit (3 s) is 10 ng l⁻¹ for the two species and the relative standard deviation (n=10) at the 200 ng l⁻¹ level is 3.5% for selenite and 5.6% for selenate. The addition of selenite and selenate stock standard solutions to tap water samples yields a 97-103% recovery of both species.     

Blank values, adsorption, pre-concentration, and sample preservation for arsenic speciation of environmental water samples

Arsenic is the focus of public attention because of its toxicity. Arsenic analysis, its toxicity, and its fate in the environment have been broadly studied, still its blank values, adsorption to sampling materials and pre-concentration of water samples as well as stabilization of arsenic compounds in water samples under field conditions have been very little investigated. In this study, we investigate the blank values and adsorption of arsenic compounds for different laboratory materials. We focused our work onto pre-concentration of water samples and how to stabilize arsenic compounds under field conditions. When using glassware for arsenic analysis, we suggest testing arsenic blank values due to the potential release of arsenic from the glass. Adsorption of arsenic compounds on different laboratory materials (<10%) showed little influence on the arsenic speciation. Pre-concentration of methanol-water solutions could result in potential overestimation of arsenic compounds concentrations. Successful pre-concentration of water samples by nitrogen-purge provides an analytical possibility for arsenic compounds with high recoveries (>80%) and low transformation of arsenic compounds. Thus, concentrations as low as 1 ng As l⁻¹ can be determined. Addition of ethylenediaminetetraacetic acid (EDTA) and storage in the dark can decrease the transformation among arsenic compounds in rainwater and soil-pore water for at least a week under field conditions.     

Temperature-controlled ionic liquid-liquid-phase microextraction for the pre-concentration of lead from environmental samples prior to flame atomic absorption spectrometry

Hydrophobic ionic liquid could be dispersed into infinite droplets under driving of high temperature, and then they can aggregate as big droplets at low temperature. Based on this phenomenon a new liquid-phase microextraction for the pre-concentration of lead was developed. In this experiment, lead was transferred into its complex using dithizone as chelating agent, and then entered into the infinite ionic liquid drops at high temperature. After cooled with ice-water bath and centrifuged, lead complex was enriched in the ionic liquid droplets. Important parameters affected the extraction efficiency had been investigated including the pH of working solution, amount of chelating agent, volume of ionic liquid, extraction time, centrifugation time, and temperature, etc. The results showed that the usually coexisting ions containing in water samples had no obvious negative effect on the recovery of lead. The experimental results indicated that the proposed method had a good linearity (R = 0.9951) from 10 ng mL⁻¹ to 200 ng mL⁻¹. The precision was 4.4% (RSD, n = 6) and the detection limit was 9.5 ng mL⁻¹. This novel method was validated by determination of lead in four real environmental samples for the applicability and the results showed that the proposed method was excellent for the future use and the recoveries were in the range of 94.8-104.1%.     

Determination of ultra trace arsenic species in water samples by hydride generation atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) methodology has successfully been employed for the preconcentration of ultra-trace arsenic species in aqueous samples prior to hydride generation atomic absorption spectrometry (HGAAS). As(III) has formed an ion-pairing complex with Pyronine B in presence of sodium dodecyl sulfate (SDS) at pH 10.0 and extracted into the non-ionic surfactant, polyethylene glycol tert-octylphenyl ether (Triton X-114). After phase separation, the surfactant-rich phase was diluted with 2 mL of 1 M HCl and 0.5 mL of 3.0% (w/v) Antifoam A. Under the optimized conditions, a preconcentration factor of 60 and a detection limit of 0.008 μg L⁻¹ with a correlation coefficient of 0.9918 was obtained with a calibration curve in the range of 0.03–4.00 μg L⁻¹. The proposed preconcentration procedure was successfully applied to the determination of As(III) ions in certified standard water samples (TMDA-53.3 and NIST 1643e, a low level fortified standard for trace elements) and some real samples including natural drinking water and tap water samples.     

Multiple microflame quartz tube atomizer: Study and minimization of interferences in quartz tube atomizers in hydride generation atomic absorption spectrometry

A systematic study was performed to evaluate the performance of a multiple microflame (MM) quartz tube atomizer (QTA) for minimizing interferences and to improve the extent of the calibration range using a batch system for hydride generation atomic absorption spectrometry (HG AAS). A comparison of the results with conventional QTA on the determination of antimony, arsenic, bismuth and selenium was performed. The interference of As, Bi, Se, Pb, Sn and Sb was investigated using QTA and MMQTA atomizers. Better performance was found for MMQTA, and no loss of linearity was observed up to 160 ng for Se and Sb and 80 ng for As, corresponding to an enhancement of two times for both analytes when compared to QTA (analyte mass refers to a volume of 200 μl). For Bi, the linear range was the same for QTA and MMQTA (140 ng). With the exception of Bi, the tolerance limits for hydride-forming elements were improved more than 50% in comparison to the conventional QTA system, especially for the interferences of As, Sb and Se. However, for Sn as an interferent, no difference was observed in the determination of Se and Sb using the MMQTA system. The use of MMQTA-HG AAS complied with the relatively high sensitivity of conventional QTA and also provided better performance for interferences and the linear range of calibration.