单扫描示波极谱法连测五味子、榛蘑中的铜和锌

研究了在HCl-KSCN底液中用单扫描示波极谱法连续测定五味子、榛蘑中铜和锌的方法。在此底液中,铜、锌分别在-0．42V(vs．SCE)、-1．03V(vs．SCE)处产生一敏锐的二阶导数波,检出限分别为0．005、0．01μg／mL,线性范围分别为0．01～8．00μg／mL,0．01～10．00μg／mL。应用本方法测定了五味子、榛蘑中的铜和锌,方法回收率为96．5％～101．8％。     

极谱吸附波测定硫酸锌中微量镉

研究了在pH5．5的HOAc-NaOAc-抗坏血酸－KI溶液中,用单扫描示波极谱法获得镉与KI络合物吸附波用于微量镉测定的方法,峰电位在－0．73V（vs.SCE),峰电流与镉在0．4－80ug/50ml范围内呈良好的线性关系,检出限为4ug.L^-1,线性回归曲线方程为I＝3．47x(ug/50ml)-0.02,相关系数r=0.9998,测定硫酸锌中镉的标准加入回收率可达99－102％。     

催化动力学光度法测定茶叶和中药中的单宁

在盐酸介质中,微量单宁对碘酸钾氧化丙基红的褪色反应有显著的催化作用,据此建立了催化动力学光度法测定微量单宁的新方法。方法的线性范围为0．1～3．0／μg／mL,检出限为0．04／μg／mL。本法简便、快速、灵敏度高和选择性较好,用于茶叶和中药五倍子、诃子中单宁含量的测定,结果满意。     

二极管阵列检测-激光诱导荧光光度法测定食品中痕量铜

为了建立食品中痕量铜的新分析方法,本文利用自行组装的激光诱导荧光－CCD二极管阵列检测器－计算机联用装置,研究了铜催化H2O2氧化罗丹明B的反应体系,在氨－氟化铵（pH=9.0)缓冲溶液中,激发波长532．0nm,发射波长580．0nm条件下,采用催化荧光光度法实现了食品样品中痕量铜的测定,方法的线性范围0．5－4．0ug/L,方法的检出限为0.5ug/L,加标回收率为86．9％－108．6％,s相对偏差不大于9．70％。     

大黄中大黄酚的二阶导数差示脉冲极谱法定量研究

建立了中草药大黄中大黄酚的二阶导数差示脉冲极谱定量分析方法。大黄酚在1moL／L氢氧化钾-1moL／L盐酸-甲醇(体积比为1：2：22)的溶液中,于-0．130V(vs．Ag／AgCl)处产生二阶导数差示脉冲极谱峰,大黄酚的浓度在10～80ug／mL范围内与其峰幅值呈良好的线性关系,线性相关系数r=0．9998,检出限为8．6ng／mL。测定结果的相对标准偏差为1．17％(n=8),加标回收率为100．0％。     

极谱法测定人发中痕量铜的研究

研究了痕量铜与CNS-及TriTonX 30 5非离子表面活性剂形成多元配合物 ,用示波极谱分析法测定痕量铜的新方法 .新方法铜的析出限为 1× 10 -10 g/mL ,工作曲线线性响应浓度范围为 5× 10 -9～ 5× 10 -7g/mL ,回收率为 98%～ 10 3% .直接用于人发、血清等样品中痕量铜的测定 ,其结果与原子吸收分光光度法测定结果对照相吻合     

流动注射催化动力学光度法测定碘的研究

本文采用流动注射技术,利用微量碘离子催化铁的硫氰酸配合物与亚硝酸钠的褪色反应,实现水中微量碘离子的催化动力学光度测定。该法测定碘离子的线性范围是1．0～7．0μg／mL,检出限为0．5μg／mL,相对标准偏差为5．0％。方法用于实际水样中微量碘离子的测定,结果令人满意。     

高效液相色谱法测定山生柳中酚苷类成分的含量

用高效液相色谱法测定山生柳中水杨苷、水杨酰水杨苷和木犀草素07－O－葡萄糖苷的含量，流动相为1．5％醋酸溶液－甲醇，Symmetry C18柱，柱温30℃，流速1．1mL/min，检测波长270nm，线性浓度范围分别为527．0－105．4um/mL,140-28.0ug/mL,81.0-16.2ug/mL，平均回收率是104．9％和103．6％，RSD分别为2．0％，0．3％和0．3％。     

锑(Ⅲ)-溴邻苯三酚红导数示波极谱法测定锌浸出液中的锑

在pH2．5的硫酸介质中，锑(Ⅲ)与溴邻苯三酚红生成的络合物产生一个灵敏的导数极谱波，其导数波峰值电位为-0．56V(vs．SCE)，线性范围0．0l～0．5μg／mL，许多离子不干扰测定，不需要分离与富集，直接测定锌浸出液中不同含量的锑。     

五氧化二钒中微量镁的测定

本文采用共沉淀定量分离方法对五氧化二钒中所含微量镁进行极谱测定。检出限为1．5mg/L，线性范围为0～0．4mg／L。精确度为：标准偏差S=0．14，变异系数CV=1．92％；相对误差为2．3％．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.