Investigation of II –VI alloy lattice dynamics by IR spectroscopic ellipsometry

Optical properties related to lattice vibrations of bulk Zn_1‐xBe_xSe, Zn_1‐x‐yBe_xMn_ySe and Cd_1‐xBe_xSe alloys are reported. Optical phonons of the mixed crystals grown by the Bridgman method have been investigated by infrared spectroscopic ellipsometry in the wave‐number range 300‐8000 cm^‐1. The complex dielectric functions can be reproduced using a model with two or three classical damped oscillators corresponding to the BeSe‐like transverse‐optical phonon‐modes and a Drude contribution from the free carriers. The frequencies of longitudinal‐optical phonons have been found from the imaginary parts of the dielectric loss functions. The influence of the alloy composition on the zone‐centre optical phonon frequencies is discussed. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural,optical and dielectric studies on K1‐x(NH4)xH2PO4 mixed crystals grown from z‐cut seeds

Mixed crystals of K_1‐x(NH₄)_xH₂PO₄(KADP) were grown from KDP (KH₂PO₄) dominated mixed solutions with varying molar proportion of ADP (NH₄H₂PO₄) addition. It was found that, as the increase of ADP molar concentration, the growth rate along z‐axis of KADP crystal decreased rapidly. The structure of KADP crystals was investigated by powder XRD and the lattice parameter was calculated. The results showed that the lattice parameter c of KADP crystal increased with the molar concentration of ADP. The optical homogeneity of grown KADP crystals was determined with a differential phase‐shifting interferometry. Frequency dependences of the dielectric constant and dielectric loss of KADP crystals were measured at room temperature (290 K). The dielectric constants of KADP crystals were almost invariant with the increase of frequency. In the region of 10²∼10⁴Hz, the values of the dielectric loss reduced with the increase of frequency. The piezo‐resonance coupling effect still exists in KADP crystals at room temperature, but shifted to low frequency band. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth and characterization of K1‐x(NH4)xH2PO4 mixed crystals onto z‐cut point seeds

Mixed crystals of potassium dihydrogen phosphate and ammonium dihydrogen phosphate were grown onto point seeds by the method of temperature reduction. It was found that the regeneration process of z‐cut point seeds became more and more difficult with increasing KH₂PO₄ concentration in the solution mixture. The interior stress and cracking of the mixed crystals were analyzed by synchrotron X‐ray topography. Large numbers of stress stripes were found at the seed and sectors boundaries. The lattice parameters of the pyramid and prismatic sectors of the prepared mixed crystal were calculated according to the X‐ray diffraction patterns. With solution containing 8 mol % KH₂PO₄, the lattice volumes of the prismatic sector of the mixed crystal were 1.3% larger than that of the pyramid sector of the crystal. Chemical etching revealed microcracks with length of hundreds of microns in the mixed crystals, which tended to spread and led to crystal cracking. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of crystal disorder on linewidth of the Raman modes in GaS1‐xSex layered mixed crystals

The linewidths of Raman‐active intralayer compressional modes in GaS_1‐xSe_x layered mixed crystals (0 ≤ x ≤ 1) have been measured in the 10‐300 K temperature range to study the anharmonic effect as a function of compositional variation and temperature. It was found that the anharmonicity increases with an increase in substitutional disorder. The cubic (three‐phonon) processes with energy conservation is responsible for the anharmonic contribution to the broadening of the intralayer phonon lines with temperature. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Composition Dependency of Lattice Anisotropy of TlBX2‐type Chain Mixed Crystals

Variation of the lattice parameters of TlTl_1‐xIn_xSe₂ chain mixed crystals with composition have been studied by X‐ray diffraction technique. The lattice anisotropy ( c/a ) of the TlBX₂‐type mixed crystals changes linearly with substitution of the atoms located both at the center and at the vertices of the BX4 tetrahedra. A brief survey of the important features of the effect of isomorphic atom substitution on the lattice anisotropy of TlBX₂‐type mixed crystals with chain structure has been presented.     

Growth,structure and thermal properties of CuAlxGa1‐xSe2 alloys

Ingots of the CuAl_xGa_1‐xSe₂ (0 ≤ x ≤ 1) alloys system were prepared by direct fusion of the stoichiometric mixture of the elements. The analysis of X‐ray Powder Diffraction data showed the presence of one single phase with chalcopyrite tetragonal structure at room temperature for all the studied compositions. The lattice parameters, a and c, and the bond lengths were calculated. The phase transition temperatures were obtained by the onset method from Differential Thermal Analysis measurements performed on samples sealed in evacuated quartz ampoules. Fusion or transition enthalpies were determined from the area of the corresponding DTA peak. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Compositional dependence of morphology and lattice parameters during growth of K1‐x(NH4)xH2PO4 mixed crystals

Mixed crystals of ammonium dihydrogen phosphate and potassium dihydrogen phosphate K_1‐x(NH₄)_x H₂PO₄ were grown from aqueous solutions with x = 0.06, 0.09, 0.15, 0.32, 0.42, 0.51, 0.63, 0.70, 0.76, 0.78, 0.84, 0.88, 0.89 and 0.91. The crystal composition that differs from solution was estimated by X‐ray method. Morphology of the crystals changes from tetragonal prism to needles when the incorporation of either of the two components into the other; which also affects the growth rate along the prominent growth directions significantly. Growth along the [001] decreases initially with composition and reached the maximum when x = 0.5; whereas growth along the [100] always showed a decreasing trend with composition and attained a minimum value when x = 0.5. Crystal length along the [001] and [100] and aspect ratio are also compositional dependent. Unit cell parameters determined by X‐ray powder and single crystal analyses revealed that the ‘a ’ parameter shows only a small and linear variation but the ‘c ’ parameter changes significantly with ADP incorporation because of the difference in the effective ionic radius of K⁺ and NH₄⁺ ions and also the possibility of NH₄⁺ ion to form two different kinds of hydrogen bonds in the system. The existence of a pseudo‐cubic cell at the mixing composition x = 0.78 was also revealed. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of x‐irradiation on indentation size effect and formation of cracks for [Ky(NH4)1‐y]2ZnCl4 mixed crystals

The effects of x‐beam irradiation with different doses on microhardness and its related physical constants on [K_y(NH₄)_1‐y]₂ZnCl₄ mixed crystals with concentrations, y equals 0.000, 0.232, 0.644, 0.859 or 1.000 has been studied. The tests were performed for x‐doses from 0.2 kGy up to 1.6 kGy for loads from 20 to 160 g. The variation of hardness on (010) faces of orthorhombic [K_y(NH₄)_1‐y]₂ZnCl₄ mixed crystals with load were studied. The experimental results showed that, the hardness decreased as the x‐doses increased. Variation of the microhardness follows the normal ISE trend for low x‐doses and un‐irradiated crystals, then follows the reverse ISE trend for high x‐doses. Analysis of the experimental results revealed that: the radial cracks length, indentation size and applied indentation load are mutually related, and these dependences related with fracture mechanics are the basis of Meyer's empirical law. Indentation size effect (ISE) can be explained satisfactory by Hays‐Kendall's approach and proportional specimen resistance model. Brittleness of two cracks system are applicable for characterizing cracks around indentation impression (i.e. radial cracks) and another is (lateral cracks) for [K_y(NH₄)_1‐y]₂ZnCl₄ mixed crystals, crystals in the load range 60 – 160 g. It is shown that indentation induced microhardness decreases, whereas the length of radial cracks induced on indentation increases with the increase of x‐doses. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Comment on “Debye temperature and melting point of II‐VI and III‐V semiconductors” [Cryst. Res. Technol. 45, No. 9, 920–924 (2010)]

In the present work, we have readjusted some empirical parameters obtained by Kumar et al. in their work which contains some numerical errors.     

Synthesis,characterization and hydrogen sorption studies of mixed sodium‐potassium alanate

The aim of the present investigation is to synthesize mixed sodium potassium alanate (K₂NaAlH₆) and to explore its hydrogen sorption characteristics. K₂NaAlH₆ is synthesized through ball milling of KH and NaAlH₄ in the molar ratio 2:1 under hydrogen pressure of 10 bar. The temperature programmed desorption experiment shows that the synthesized K₂NaAlH₆ has peak desorption temperature of ∼352°C and reveals appreciable rehydrogenation kinetics under 6 bar hydrogen pressure at 300°C. The investigations are also focused on the catalytic effect of carbon nanostructures (CNS) namely, the graphene sheet (GS) and single wall carbon nanotube (SWCNT) and titanium halides (TiCl₃ and TiF₃) on K₂NaAlH₆. In the case of graphene and SWCNT catalyzed K₂NaAlH₆, the peak desorption temperature gets reduced to ∼347°C and ∼341°C respectively. The catalytic effects of CNS and titanium halide on K₂NaAlH₆ are also compared in the investigation. Between the two types of catalysts, halides are found to be better than CNS and out of the two halides, TiF₃ is found to be the best catalyst for hydrogen sorption in K₂NaAlH₆. The peak desorption temperature decreases significantly from 352°C to ∼324°C for TiF₃ catalyzed K₂NaAlH₆. Thus, the desorption activation energy reduces drastically from 124.43 kJ/mol (synthesized K₂NaAlH₆) to 88.05 kJ/mol for TiF₃ catalyzed K₂NaAlH₆.     

Debye temperature and melting point of II‐VI and III‐V semiconductors

In this paper, simple relations are proposed for the calculation of Debye temperature θ_D and melting point T_mof II‐VI and III‐V zincblende semiconductors. Six relations are proposed to calculate the value of θ_D. Out of these six relations, two are based on plasmon energy data and the others on molecular weight, melting point, ionicity and energy gap. Three simple relations are proposed to calculate the value of T_m. They are based on plasmon energy, molecular weight and ionicity of the semiconductors. The average percentage deviation of all nine equations was calculated. In all cases, except one, it was estimated between 3.34 to 17.42 % for θ_D and between 2.37 to 10.45 % for T_m. However, in earlier correlations, it was reported between 10.59 to 33.38% for θ_D and 6.96 to 14.95% for T_m. The lower percentage deviation shows a significant improvement over the empirical relations proposed by earlier workers. The calculated values of θ_D and T_m from all equations are in good agreement with the available experimental values and the values reported by different workers. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth and characterization of superconductive Nd2‐xCexCuO4‐y single crystals

Nd_2‐xCe_xCuO_4‐y single crystals with different x values have been successfully grown by Traveling Solvent Floating Zone method (TSFZ). Electronic properties of Nd_2‐xCe_xCuO_4‐y single crystals with various x have been studied in detail. The results show that superconductivity can be found in crystals with x > 0.1 (0.13‐0.18) directly grown at oxygen‐reduced atmosphere without post‐annealed, while no superconductivity appears in crystals with x < 0.1 at the same atmosphere. It is also found that, the segregation coefficient of Ce is determined to be 0.946 and transition temperature Tc (onset) reaches maximum value of 23.5 K at nominal composition x = 0.165. With further increase of Ce concentration, transition temperature of single crystals declines due to the precipitation of secondary Phases. In addition, the variation of lattice constants of Nd_2‐xCe_xCuO_4‐y single crystals with different x is also given. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The Characteristics of the Mixed Crystals of the KNO3‐NH4NO3‐H2O System at 298 K

The equilibrium studies of the KNO₃‐NH₄NO₃‐H₂O system at 298 K have been conducted. The isotherm of solubility and the curve of distribution have been mathematically described. The parameters of the crystal lattice and the enthalpy of crystallization of the [K_x(NH₄)_1‐x]NO₃ solid solutions as a function of their composition have been presented. The structure of salts KNO₃�xNH₄NO₃ with different x values have been solved and refined.     

Low‐Temperature Raman Scattering Spectra of GaSexS1‐x Layered Mixed Crystals

Raman scattering has been used to study the vibrational spectra of GaSe_xS_1‐x layered mixed crystals at 10 K. We report the frequency dependencies of different modes on composition x, with particular emphasis on A′₁⁽²⁾ (A_1g¹) and A′₁⁽⁴⁾ (A_1g²) intralayer compressional modes having low dispersion in the Brillouin zone. The appearance of additional bands is attributed to multimode behavior typically exhibited by mixed crystals of anisotropic compounds.     

Geometrical aspects of solid solution separation by evaporation‐condensation driven in a closed system by a small temperature difference

Evaporation‐condensation driven in a closed system by a small temperature difference has demonstrated its ability to deliver semiconducting IV‐VI and II‐VI solid solution crystals of highest compositional uniformity. Geometrical aspects of solution component distribution emerging in the crystals grown in the near equilibrium evaporation/condensation systems are considered in this paper. The conclusion is drawn that no increase in the range of compositional variations with increase in the crystal size is to be anticipated. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Determination of the phase diagram for the crystallization of L‐asparaginase II by a turbidity technique ‐ part II. ‐MPD and crystallography studies‐

The phase diagram for the crystallization of L‐asparaginase II including the metastable zone width (MZW), in the presence of PEG₆₀₀₀ and ethanol, respectively, has been studied by an online turbidity technique out of the crystallization in solution (see part I of this work 1 ). Here this paper describes a further investigation on constructing a phase diagram including MZW for the crystallization of L‐asparaginase II with a different precipitant agent of 2‐methyl‐2, 4‐pentandiol (MPD). Along with the phase diagram, the single crystal X‐ray data were successfully collected at 100K from a crystal formed in the presence of 26% (v/v) MPD. The crystals indicate an orthorhombic form and belong to the space group of P2₁2₁2₁ with the unit cell parameters a = 93.9, b = 125.77, c = 151.75Å. The crystal diffracted up to a resolution of 2.88 Å.     

Synthesis,spectroscopic studies and ab‐initio structure determination from X‐ray powder diffraction of bis‐(N‐3‐acetophenylsalicylaldiminato)copper(II)

The synthesis, spectroscopic studies and crystal structure determination from X‐ray powder diffraction have been carried out for bis‐(N‐3‐acetophenylsalicylaldiminato)copper(II). The structure is triclinic, space group P1 with unit cell dimensions a = 11.817(1) Å, b = 12.087(1) Å, c = 9.210(1) Å, α = 102.62(1)°, β = 111.16(1)°, γ = 86.15(1)°, V = 1197.0(2)ų, Z = 2. The structure has been solved by Monte Carlo simulated annealing approach and refined by GSAS package. The final Rp value was 8.68%. The coordination geometry around the copper atom in the complex is intermediate between square‐planar and tetrahedral with two salicylaldimine ligands in trans arrangement. Intermolecular C–H…O hydrogen bonds between molecules related by translation generate infinite chains along [010] direction. The molecular chains are linked via additional C–H…O hydrogen bonds to form a three‐dimensional supramolecular network. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of cationic substitution on lattice constants and optical characterization in solution grown mixed crystals of potassium‐ ammonium zinc chloride

Mixed crystals of potassium‐ammonium zinc chloride in different concentrations were grown from aqueous solution employing the techniques of slow cooling and controlled evaporation. Powder x‐ray diffraction studies were carried out on the grown crystals. The comparison between lattice parameters a, b and c are experimentally determined and calculated by Vegad's law. The concentration of K⁺ ions in the crystals was measured by the atomic absorption technique. The crystal morphology changed considerably by increasing K⁺ concentration. The optical absorption coefficient (α) indicated strong influence changing concentration. The optical energy gap was found to decrease with increasing K⁺ concentration. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Morphology of silver bromide crystals produced at presence of N,N ‐dimethylformamide

The study deals with examination of conditions that are necessary to obtain flat crystals of silver bromide that grow in a water and gelatine crystallization environment where N,N ‐dimethylformamide is used as the agent that is conducive to complexing of sparingly soluble silver bromide. The examination focused on the issue how changes in volumetric concentration of N,N ‐dimethylformamide as well as concentration of excessive ions of silver bromide in the dispersive solution affect morphology and size of newly created of silver bromide. The completed experiments enabled to determine boundary limits of both N,N ‐dimethylformamide and bromide ions concentration where suspensions of silver bromide crystals exhibit predominant content of triangular, transient and hexagonal flat forms with very high aspect ratio. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal structure,spectroscopic studies and non‐linear optical properties of 2‐amino‐3‐nitropyridinium trichloroacetate

A new quadratic nonlinear optical crystal, 2‐amino‐3‐nitropyridinium trichloroacetate (2A3NPTCA), was synthesized and the single crystals were grown by slow evaporation method at room temperature. Single crystal X‐ray diffraction and powder X‐ray diffraction experiments were carried out in order to confirm the structure and crystalline nature of 2A3NPTCA crystal. The chemical bonding and various functional groups present in the 2A3NPTCA were identified from FT‐IR spectrum. The UV–visible–NIR transmission spectrum shows that it is suitable for frequency‐converting in the wavelength region of 431–1200 nm. Thermogravimetric (TG) and differential thermal analysis (DTA) were carried out to characterize the thermal behaviors of the grown crystals. Kurtz and Perry powder method for second harmonic generation (SHG) measurements demonstrate that 2A3NPTCA is a phase matching material and its nonlinear optical efficiency is two times that of KDP. All the above results suggest that 2A3NPTCA is a potential candidate of NLO material.