Preparation of Y3Al5O12 nanocrystals by low temperature glycol route

Yttrium aluminum garnet, Y₃Al₅O₁₂ (YAG) nanocrystals were synthesized by low temperature glycol method. This is a modified sol–gel method performed at low temperature that consists of a mixture of salts, mostly nitrates in an aqueous media. Single phase nanocrystalline YAG was obtained at 850°C, which is much lower than others such as wet‐chemical techniques. The structural characterization is done by XRD and transmission electron microscopy. The crystallite size range from 20‐50 nm was observed for the materials prepared at 850‐ 950°C. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

An X‐ray powder diffraction study of the microstructural evolution on heating 3:2 and 2:1 mullite single‐phase gels

Single‐phase gels with compositions 3Al₂O₃·2SiO₂ and 2Al₂O₃·SiO₂ were prepared by gelling mixtures of aluminium nitrate and tetraethylorthosilicate. Gels were fast heated at different temperatures between 900°C and 1600°C. The phase transformation and microstructural changes of both mullite precursor gels over the temperature range were followed by X‐ray powder diffraction (XRD), lattice parameter determination (LP), and scanning and transmission electron microscopies (SEM and TEM). The distribution of crystallite sizes and strains were determined by linewidth refinements of X‐ray diffraction patterns using the integral breadth method of Langford and the Warren‐Averbach analysis. XRD of both heated gels showed the formation of crystalline mullite single phase. Some amount of glassy phase coexisted with mullites at low temperatures, i. e. below 900°C. The compositional range of mullites formed on heating gels at temperatures between 900°C and 1600°C was dependent on the starting nominal composition of gels. SEM and TEM micrographs of both heated gels below 1200°C showed the formation of small, discrete, prismatic, well‐shaped nanocrystals in a very ordered arrangement. The size of these nanocrystals was dependant on the nominal composition of gels and increased on rising the heating temperature of gel precursors. The microstructural features obtained from linewidth refinement results of X‐ray diffraction patterns also allowed to suggest the formation of prismatic a little elongated nanocrystals at temperatures below 1200°C. Microstrain values were small and only displayed a relatively significant value for mullites processed at 900°C. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and characterization of magnetite nanocrystals

Nanocrystals of magnetite (Fe₃O₄) were prepared by sol‐gel technique. The prepared nanocrystals were characterized for phase by powder X‐ray diffraction (XRD) of the samples annealed at successively higher temperature. The magnetite phase was formed during the annealing of the synthesized powder at 400 °C for a few hours. The Fourier transform infrared spectroscopy (FTIR) was performed to analyze the functional groups in the material. The energy dispersive X‐ray diffraction (EDAX) was performed for chemical composition analysis. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques were used to analyze the morphology of nanocrystals and for estimating their average size. The results confirm the formation of Fe₃O₄nanocrystals of the sizes ∼20–50 nm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A novel thermolysis method of colloidal protein precursors to prepare hydroxyapatite nanocrystals

A novel thermolysis method of colloidal protein precursors is introduced to prepare hydroxyapatite (HAP) nanocrystals. The colloidal protein precursors are sonochemically synthesized from saturated Ca(OH)₂ aqueous solution, Ca(H₂PO₄)₂ aqueous solution and bovine serum albumin (BSA) molecules. The colloidal protein precursors are amorphous and composed of 15‐90 nm near spherical calcium phosphate nanoparticles and BSA molecules. The particle size analysis shows the volume particle size distribution is from 9.0 nm to 222.6 nm and the volume‐averaged particle size is 45.8 nm. During the calcination procedure BSA molecules are burningly removed and the HAP nanocrystals can be obtained at 500 °C. The effects of BSA concentration on the properties of samples are discussed. Results show that BSA combustion can promote the transformation of crystalline HAP from amorphous material. Moreover, the increase of BSA concentration reduces the crystalline sizes of HAP crystals and the crystallinity of product. With BSA concentration of 5 g/L, the obtained HAP nanocrystals are mainly 25∼100 nm similar spherical nanoparticles besides some 40∼70 nm×75∼150 nm short rod‐like crystals. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Nd(III) and Yb(III) ions incorporated in Y4Al2O9 obtained by sol‐gel method: synthesis,structure, crystals and luminescence

The nanocrystalline powders of Y₄Al₂O₉ (YAM) pure and doped by Nd, Yb and codoped by Nd and Yb were obtained via modified sol‐gel method. These powders were characterized by X‐ray diffraction method, scanning electron microscopy and high resolution scanning electron microscopy, luminescence spectroscopy and differential thermal analysis (DTA). We obtained single phase powders of crystalline structure with average size 70 nm exhibiting interesting luminescent properties. Efficient non‐radiative energy transfer between Nd and Yb was found. DTA confirmed the phase transition at about 1400 °C. From these nanocrystalline powders, the crystals YAM:Yb, YAM:Yb,Nd were grown by micro‐pulling down technique. They were cracking during cooling owing to the phase transition. Luminescent properties of YAM:Nd,Yb crystals were identical with properties of corresponding nanopowders within experimental incertitude. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural investigation and electronic band transitions of nanostructured TiO2 thin films

Titanium dioxide (TiO₂) thin film was deposited on n‐Si (100) substrate by reactive DC magnetron sputtering system at 250 °C temperature. The deposited film was thermally treated for 3 h in the range of 400‐1000 °C by conventional thermal annealing (CTA) in air atmosphere. The effects of the annealing temperature on the structural and morphological properties of the films were investigated by X‐ray diffraction (XRD) and atomic force microscopy (AFM), respectively. XRD measurements show that the rutile phase is the dominant crystalline phase for the film annealed at 800 °C. According to AFM results, the increased grain sizes indicate that the annealing improves the crystalline quality of the TiO₂ film. In addition, the formation of the interfacial SiO₂ layer between TiO₂ film and Si substrate was evaluated by the transmittance spectra obtained with FTIR spectrometer. The electronic band transitions of as‐deposited and annealed films were also studied by using photoluminescence (PL) spectroscopy at room temperature. The results show that the dislocation density and microstrain in the film were decreased by increasing annealing temperature for both anatase and rutile phases. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of crystalline fibres of codoped BaAl2O4:Eu2+:Cr3+

Phosphor material BaAl₂O₄:Eu²⁺, Cr³⁺ with varying concentrations of Cr co‐doping were prepared by solid‐state synthesis method. Crystalline fibres were obtained by controlled annealing temperature. Synthesized compositions were characterized for their phase and crystallinity by powder x‐ray diffraction. The crystalline morphology was investigated using SEM analysis. High resolution transmission electron microscopy (HRTEM) in image and diffraction modes was used to investigate the microstructure. The effect of Cr doping on quality and morphology of grown crystals was investigated. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of annealing temperature on the structural and optical properties of amorphous Sb2Te2Se thin films

Thin films of Sb₂Te₂Se were prepared by conventional thermal evaporation of the presynthesized material on Corning glass substrates. The chemical composition of the samples was determined by means of energy‐dispersive X‐ray spectrometry. X‐ray diffraction studies on the as‐deposited and annealed films revealed an amorphous‐to‐crystalline phase transition. The as‐deposited and annealed films at T _a = 323 and 373 K are amorphous, while those annealed at T _a= 423 and 473 K are crystalline with a single‐phase of a rhombohedral crystalline structure as that of the source material. The unit‐cell lattice parameters were determined and compared with the reported data. The optical constants (n , k ) of the investigated films were determined from the transmittance and reflectance data at normal incidence in the spectral range 400–2500 nm. The analysis of the absorption spectra revealed non‐direct energy gaps, characterizing the amorphous films, while the crystalline films exhibited direct energy gaps. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Studies on the structural,thermal and optical behaviour of solution grown organic NLO material: 8‐hydroxyquinoline

Single crystal of 8‐hydroxyquinoline (8HQ) having chemical formula C₉H₇NO, an organic nonlinear optical (NLO) material has been successfully grown by slow evaporation solution growth technique at room temperature. The crystal system has been confirmed from the powder X‐ray diffraction (PXRD) analysis. The crystalline perfection was evaluated by high resolution X‐ray diffractometry (HRXRD). From this analysis we found that the quality of the crystal is quite good. However, a very low angle (tilt angle 14 arc sec) boundary was observed which might be due to entrapping of solvent molecules in the crystal during growth. Its optical behavior has been examined by UV‐Vis. analysis, which shows the absence of absorbance between the wavelengths ranging from 400 to 1200 nm. From the thermal analysis it was observed that the material exhibits single sharp weight loss starting at 113°C without any degradation. The laser damage threshold was measured at single shot mode and the SHG behavior has been tested using Nd:YAG laser as a source. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Transmission spectra of crystals at elevated temperatures for the calculation of internal radiant heat transport during crystal growth – Part 2: Spectra of YAG:Cr,YVO4:Nd and the bandgap variation of various materials

The transmission spectra in the range from 350 to 3500 nm of the two most complex materials with regard to radiant heat transport – YAG:Cr⁺⁴ and YVO₄:Nd – are reported for temperatures between 25 and 1310 °C. The extreme shift of the short wavelength cut‐off (band gap) of YVO4:Nd with temperature is shown in comparison to that of some other materials. In YAG:Cr⁴⁺ we found a light‐induced absorption band near 2000 nm besides a strong reduction of the transmission in the visible and the near IR with increasing temperature. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Thermal conductivity and refractive indices of Nd:GdVO4 crystals

The thermal conductivities of Nd:YAG, M(Y,Gd)VO₄ crystals were measured at 298 K. The value of Nd:GdVO₄ crystal along <001> direction was 11.4 W/mK, which was higher than that of YAG crystal measured to be 10.7 W/mK. The principal refractive indices of Nd:GdVO₄ crystal in the temperature range from 20 °C to 170 °C were determined by auto‐collimation method. Based on the measured values of refractive indices, the Sellmeier equation and expression of temperature dependence of refractive indices have been obtained. The measured results show that the birefringence Δn is 0.22007 at 20 °C and temperature coefficient of birefringence is 4.33 × 10⁻⁶/°C for 1.064 μm. These results prove that the GdVO₄ crystal is a laser crystal with excellent thermal and birefringence properties. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystallization of benzimidazole by solution growth method and its characterization

The potential organic NLO crystal of benzimidazole (BMZ) has been successfully grown by slow evaporation solution growth technique at room temperature. The crystalline perfection has been verified by High resolution X‐ray diffraction (HRXRD) analysis. The very low angle boundary obtained for this solution‐grown specimen may be attributed to the segregation of solvent molecules (methanol), which were entrapped within the crystal during growth. The laser damage threshold has been measured by using high intensity Q‐switched Nd:YAG laser. The observed value is greater than that of KDP and lesser than that of melt grown benzimidazole. The NLO efficiency has been determined and it is compared with the KDP crystal. The thermal behaviour has been assessed by TG/DTA analysis. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Comparative study on photoluminescence of amorphous and nano-crystalline YAG:Tb phosphors prepared by a combustion method

Amorphous and nano-crystalline Y₃Al₅O₁₂:Tb phosphor samples were obtained via a facile combustion method by calcination at various temperatures, using yttrium oxide and aluminum nitrite as starting materials and citric acid as fuel. XRD, FT-IR and TEM results showed that the products were amorphous if prepared at 750 °C, well-crystalline when treated above 850 °C. In addition, partially crystalline YAG phase was observed at 800 °C (in air). The excitation spectra of the samples calcined at 750 °C and 800 °C exhibited some difference in the 230–255 nm range in comparison to those of nano-crystalline YAG:Tb, i.e. an extra band centered at 250 nm was detected via Gaussian curve-fitting. Furthermore, the photoluminescence intensity of as-synthesized samples decreased obviously with increasing the crystallinity under 250 nm excitation. Contrary, it increased monotonously when altering the excitation wavelength to 323 nm. The concentration-dependent emission spectra of samples calcined at 800 °C revealed that the strongest intensity could be obtained with 10% Tb doping. Red-shifts indicated changes of the inter-atomic distances within the Tb³⁺ coordination polyhedron with increasing Tb concentration. The low temperature photoluminescence of partially crystalline YAG:10% Tb was also investigated, displaying good-resolution but reduced intensity compared to the room-temperature photoluminescence.     

Thermal and Nonlinear Optical Properties of Ca4YO(BO3)3

Ca₄YO(BO₃)₃ (YCOB) crystals have been grown using the vertical Bridgman method. The thermal properties of YCOB were measured for the first time to our knowledge. The specific heat is 729.7 J/kg K at 373K. The average thermal expansion coefficients along the a, b and c axes are 9.9 × 10^‐6 /K, 8.2 × 10^‐6 /K and 12.8 × 10^‐6 /K, respectively, in the temperature range of 293‐1173 K. The thermal conductivities along the a, b and c axes are 1.83 W/mK, 1.72 W/mK and 2.17 W/mK at 373 K. The anisotropy in the measured thermal conductivities of YCOB is consistent with the experimental results of the thermal expansion. The SHG of a Nd: YAG laser was compared with that of a KDP crystal. The effective nonlinear coefficients (d_eff) of YCOB in type I phase matching directions of (θ, ϕ) = (66.3°, 143.5°) and (65.9°, 36.5°) were estimated to be 1.45 pm/V and 0.91 pm/V, respectively. The bulk damage threshold was observed as 85 GW/cm² for single pulse of a Nd:YAG laser with 10 ns pulseduration.     

Synthesis,structural and optical properties of well dispersed anatase TiO2 nanoparticles by non‐hydrothermal method

The formation of nanocrystalline TiO₂ particles has been investigated via a surfactant‐free synthetic non‐hydrothermal method. Titanium isopropoxide and toluene were used as the starting materials. At a low temperature of 250 °C for 6 h, the reaction mixture turned in to a white precipitate (TiO₂) as a result of the thermal decomposition of metal alkoxide. The obtained product was found to crystallize purely in the anatase phase with well defined morphology. The powder XRD study confirms that the average size of the particle is close to ∼15 nm. The TEM analysis indicates the sizes of the primary and secondary particles in the range between 8‐10 nm and 15‐20 nm respectively. The quantum size confinement of the crystallites is evident from the blue shift of the absorption edge in the UV‐Visible absorption spectrum. The luminescence property of the TiO₂ nanoparticles studied by the emission spectrum confirms the presence of defect levels caused by the oxygen vacancies. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Tb3+ luminescence enhancement of YAG:Tb3+ nanocrystals embedded in silica xerogel

The luminescence behavior of composite materials consisting of nanocrystals of Y_3?xAl₅O₁₂:Tb (YAG:Tb³⁺) embedded into silica xerogel has been studied. Blue and green luminescence of the materials is due to a cross-relaxation effect in Tb³⁺ ions doped into a YAG lattice. The materials with YAG:Tb³⁺ nanocrystals immobilized in silica exhibit enhancement of Tb³⁺ luminescence in comparison with the macrocrystalline YAG:Tb³⁺ powder. The Tb³⁺ luminescence intensity of a composite material dried at room temperature can be improved when higher aliphatic alcohols are applied in a one-pot procedure during a sol–gel synthesis. On the other hand, the Tb³⁺ luminescence is quenched in the presence of Ag nanoparticles in the material. The composite material (YAG:Tb³⁺ in silica) exhibits thermal stability at higher temperatures and achieves the highest emission intensity after having been annealed at 700 °C.     

Solvothermal synthesis and structural characterization of unfilled and Yb‐filled cobalt antimony skutterudite

Unfilled and ytterbium (Yb)‐filled cobalt antimony (CoSb₃) nanoparticles were synthesized via solvothermal route using sodium borohydride (NaBH₄) as a reducing agent. The effect of various amounts of sodium borohydride on the formation of as‐synthesized CoSb₃ nanoparticles with pure phase was investigated. It is found that a sufficient amount of NaBH₄ was required in order to form pure phase CoSb₃. In addition, the effect of annealing time and temperature on the phase transformation of the as‐prepared non‐pure phase CoSb₃ sample was also investigated. It is found that annealing at 500 °C for 5 h would eliminate those non‐CoSb₃ phases and result in pure cubic skutterudite phase CoSb₃. Structural characterization of the as‐prepared unfilled and Yb‐filled nanoparticles was carried out with transmission electron microscopy (TEM) which revealed the formation of highly crystalline cubic phase of skutterudite Yb‐filled CoSb₃. Laser induced breakdown spectroscopy (LIBS) confirmed the presence of ytterbium in the Yb‐filled CoSb₃ samples.     

Half opened microtubes of NaYF4:Yb,Er synthesized in reverse microemulsion under solvothermal condition

NaYF₄:Yb,Er micro/nanocrystals with different sizes and morphologies such as nanospheres, short flexural nanorods, and half opened microtubes, were synthesized in reverse microemulsion under solvothermal condition using the quaternary reverse microemulsion system, CTAB/1-butanol/cyclohexane/aqueous solution. The X-ray diffraction analysis confirmed that cubic phase NaYF₄:Yb,Er can completely transform to hexagonal phase with increasing reaction time. The scanning electron microscope and transmission electron microscope images revealed that the morphology of the product can be tailored by varying the reaction time. A possible crystalline growth process of the NaYF₄:Yb,Er micro/nanocrystals was discussed. The obtained half opened microtubes exhibited an intense green upconversion luminescence, which may be attractive in novel optoelectronic devices.     

Growth of Nd:GdVO4 Single Crystal and its Laser Output at 1062 nm,1342 nm

A new liquid‐phase method synthesizing Nd:GdVO₄ polycrystalline materials was introduced. High optical quality Nd:GdVO₄ single crystals have been successfully grown by the Czochralski method. The effective segregation coefficients of Nd ion in Nd:GdVO₄ crystal have been measured and discussed. Laser outputs at 1.06 μm and at 1.34 μm were achieved when Nd:GdVO₄ crystal samples of 0.52 at% Nd concentration were pumped by a high‐power LD. A maximum output of 14.5 W at 1.06 μm has been obtained when the pump power is to 26 W, giving the slope efficiency of 63%. It is reported the first time that up to 4.64 W power laser at 1.34 μm has been achieved with optical conversion efficiency of 31.4% and slope efficiency of 32.9%.     

Effect of ferric ions on the morphology and size of magnetite nanocrystals synthesized by ultrasonic irradiation

Two‐dimensional plate‐like Fe₃O₄ nanocrystals and nanoparticles could be synthesized by a simple one‐step sonochemical method through ultrasonic irradiation in reverse co‐precipitation solution at low temperature. This technique provided a facile and rapid way to prepare Fe₃O₄nanocrystals with different morphology and size. Magnetite nanoplates were synthesized with only ferrous salt adding into alkali solution, and adding ferric ions with low molar ratio in the metal salts solution would lead to the formation of very small magnetite nanoparticles (∼10 nm). The size of as‐prepared magnetite nanoparticles increased with increasing reaction temperature and showed narrow size distribution, the standard deviation less than 2 nm. This investigation indicated that ferric ions had significant influence on the morphology of Fe₃O₄ nanocrystals. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)