Nd3+:Na3La9O3(BO3)8晶体生长和光谱性能

采用顶部籽晶法生长Nd3+:Na3La9O3(BO3)8 晶体.在室温下测试了吸收光谱、发射光谱和荧光寿命.应用Judd-Ofelt理论评价了Nd3+:Na3La9O3(BO3)8晶体的光谱性能.812 nm处较宽的吸收峰适合AlGaAs LD泵浦的吸收.分别计算了Nd3+离子的唯象强度、谱线强度、辐射寿命、荧光分支比和荧光量子效率.     

Studies on a new Rb3H9(PO4)4 crystal

A new type of trirubidium nonahydrogen tetraphosphate, Rb₃H₉(PO₄)₄, crystal has been crystallized. Differential scanning calorimetry (DSC) and X‐ray diffraction measurements have been performed on the title compound. The crystal does not undergo any structural phase transition in the temperature range from 120 to 440 K except a melting transition at 399 K. The compound belongs to a monoclinic system with space group C2/c at room temperature. The structure is built on a framework of PO₄ tetrahedra linked by five types of OH‐O hydrogen bonds in the length range from 2.472(4) to 2.679(4) Å. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Room‐temperature synthesis and characterization of cross‐like Pr2(C2O4)3·10H2O micro‐particles

Cross‐like Pr₂(C₂O₄)₃·10H₂O micro‐particles were synthesized through a simple precipitation method at room temperature. The products were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), field‐emission scanning electron microscopy (FESEM), thermogravimetry–differential thermal analysis (TG‐DTA) and photoluminescence (PL). The possible formation mechanism of the cross‐like Pr₂(C₂O₄)₃·10H₂O micro‐particles was discussed, and Pr₆O₁₁ with similar morphology was obtained by calcining the oxalate precursor. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

水热反应温度对CaTi2O4(OH)2粉体微观形貌与紫外光催化性能的影响

以钛酸正丁酯和无水氯化钙为原料,采用水热法制备了不同紫外光催化特性的CaTi2O4(OH)2粉体.利用X射线衍射仪(XRD)和扫描电子显微镜(SEM)对样品的相结构和微观形貌进行了分析,并结合粉体的紫外-可见吸收分光光谱表征了材料的吸收特性及带隙宽度.研究了不同水热反应温度对CaTi2O4(OH)2物相结构、微观形貌、晶体生长特性及紫外光催化性能的影响.结果表明:水热反应温度控制在160~200 ℃时,保温36 h都能得到纯的CaTi2O4(OH)2相,粉体的形貌随着水热反应温度的提高经历了由片状和颗粒垛堆到发育成完整的片状形貌过程,当水热反应温度在200 ℃时,片与片之间出现积聚现象;在水热反应温度为180 ℃时,制备的粉体具有最高的结晶度,在紫外光5 h下对罗丹明B的催化效率最佳.     

不同填充溶剂对CaTi2O4(OH)2形貌及其光催化性能的影响

利用水热法通过改变填充溶剂的种类制备了不同形貌的CaTi2 O4(OH)2粉体.采用X射线衍射仪和扫描电子显微镜对粉体的相结构和微观形貌进行了分析,并结合粉体在紫外-可见吸收光下对罗丹明B的吸附率及光降解率进行了表征.研究了不同填充溶剂对CaTi2 O4 (OH)2的相结构、微观形貌、能带宽度以及光催化性能的影响.结果表明:乙醇和乙二醇作为填充溶剂时会抑制晶体的生长和发育,可获得纳米线状或团状CaTi2 O4 (OH)2粉体,对罗丹明B表现出较佳的吸附特性;无填充溶剂以及以水和环己烷分别作为填充溶剂可获得具有片状结构的CaTi2O4(OH)2粉体.填充环己烷能够促进CaTi2O4(OH)2相的生长和发育,结晶度最高达到了78.04;,在紫外可见光3h下对罗丹明B降解率达到91.6;.     

晶体(NH4)2C4H4O6:VO2+的EPR参量及局域结构的研究

采用叠加模型和双旋-轨耦合参量模型,建立了结构参数与EPR参量之间的定量关系;较好地解释了[VO(H2O)5]2+络离子的局域结构和EPR参量;研究结果发现,(NH4)2C4H4O6:VO2+晶体中络离子[VO(H2O)5]2+的键长为R//≈0.130nm,R⊥≈0.195nm;在(NH4)2C4H4O6:VO2+晶体中,局域结构沿C4轴方向呈压缩的八面体结构;所得EPR参量的理论计算与实验测量数据符合很好.     

亚铁离子的引入对Bi2Fe4O9纳米颗粒光催化性能的影响

本文通过在水热法过程中添加不同含量的FeCl₂合成了一系列Bi₂Fe₄O₉纯相纳米晶,成功地在Bi₂Fe₄O₉中引入了更多低价态的铁离子。紫外可见吸收谱数据证明FeCl₂的加入使得Bi₂Fe₄O₉的光学带隙从2.06 eV降低到1.96 eV。扫描电子显微镜照片和X射线衍射图谱均证明本文合成的样品为纯相正方形片状Bi₂Fe₄O₉纳米晶。在500 W汞灯照射下,对合成的三个Bi₂Fe₄O₉纳米晶样品(S1、S2、S3,分别对应不同FeCl₂含量x=0,0.2 mmol,0.4 mmol)进行甲基橙染料降解实验,结果表明在添加20 μL双氧水时,三个样品的光催化降解速率均最快,其中S3样品的光催化降解速率比S1、S2更快。因此在适当加入双氧水的情况下,FeCl₂的加入可有效提升Bi₂Fe₄O₉光催化降解染料分子的性能。     

自激活荧光粉Ba4B11O20F的水热调控及发光性能研究

以BaCO3、BaF2和H3BO3为原料,按照化学计量比采用高温固相反应法制备出了新型蓝色荧光材料Ba4B11O20F,后通过水热法对其进行二次处理.利用XRD、SEM和荧光光谱仪等对水热处理前后的粉体的物相、形貌和发光性能进行了研究.结果表明:Ba4B11O20F荧光粉在294 nm激发条件下得到的发射光谱中存在三个发射峰分别位于367 nm、402 nm和470 nm处,在紫外灯照射下成明亮的蓝色.通过研究水热工艺中的温度和加水量对粉体荧光强度的影响,得出在加水量为10 mL,恒温温度为110℃条件下获得荧光粉的荧光强度最强,比水热处理前提高了8;.水热二次处理工艺提高了粉体的纯度和结晶度,进而提高了粉体的荧光强度.     

Redetermination of the crystal structure of [Na4(H2O)14]SnS4: a compound containing a novel chain of aquated sodium ions

[Na₄(H₂O)₁₄]SnS₄ is obtained by the reaction of Na₂S·9H₂O with SnCl₄·5H₂O in aqueous solution at 21°C. It crystallizes in the space group Cc with a = 8.621(2) Å, b = 23.543(5) Å, c = 11.358(2) Å, = 110.58(3)° and V = 2158.2 ų with Z = 2. Refinement of 3826 unique reflections from a racemically twinned crystal yielded a final value of R₁ = 0.0464 (|F| > 4) and wR₂ = 0.104 and a goodness of fit of 1.125. The structure consists of a Na⁺/H₂O network supporting the tetrahedral SnS₄ ^4– anions. Water molecules or sulfide ions octahedrally coordinate each of the four crystallographically independent Na⁺ ions. The dominant feature of the structure is the existence of zigzag chains of edgeshared Na octahedra. These chains are tied together into a three-dimensional network by bridging Na(H₂O)₆ octahedra and individual H₂O molecules.     

TiO2/Ni3[Ge2O5](OH)4复合材料的制备及光催化性能

以Ni₃[Ge₂O₅](OH)₄为载体,氟钛酸铵为原料,采用水热辅助液相沉积法制备了纳米TiO₂/ Ni₃[Ge₂O₅](OH)₄复合材料。通过X射线衍射(XRD)、拉曼光谱分析(RM)、场发射扫描电子显微镜(FE-SEM)、高分辨透射电镜(HTEM)、紫外-可见吸收光谱(UV-Vis)等表征手段对样品的物相组成、结构特性及微观形貌做了检测分析,并且探究了不同二氧化钛负载量对纳米TiO₂/Ni₃[Ge₂O₅](OH)₄复合材料光降解亚甲基蓝能力的影响规律。结果表明,实验实现了纳米TiO₂与Ni₃[Ge₂O₅](OH)₄的紧密复合与有效分散,TiO₂为锐钛矿型结构,平均粒径20 nm。该复合材料能够有效抑制光生载流子的复合,改善材料的吸附性能,提高材料的光催化效率。当复合材料中TiO₂与Ni₃[Ge₂O₅](OH)₄的摩尔比为3.1∶1时,材料对亚甲基蓝的光催化效率最高,90 min亚甲基蓝的光降解率为99.81％。     

Bi掺杂对Ca3-xBixCo4O9氧化物微观结构和热电性能的影响

采用固态反应法制备Ca3-xBixCo4O9 (0.0≤x≤0.45)样品,并研究了Bi掺杂对样品的微观结构和热电性能的影响.XRD与SEM结果显示,在含Bi样品中形成了c轴取向的结构,x=0.3和x=0.45样品具有大的晶粒取向度和晶粒尺寸,这就导致了这两个样品具有较高的电导率.由于Bi3+替代Ca2+降低了载流子浓度,样品的塞贝克系数随Bi含量的增加而增加.在1000 K,x=0.3样品的功率因子可达2.77×10-4 W/m·K2,这一数值与利用热压法制备的Ca3Co4O9样品的功率因子相当.     

非线性光学晶体Na3La9O3(BO3)8的生长研究

以Na3CO3和H3BO3为助熔剂,Na3CO3和H3BO3摩尔比为7/6,熔质Na3La9O3(BO3)8和助熔剂摩尔比为1/10～1/14,采用顶部籽晶生长方法,生长Na3La9O3(BO3)8晶体,晶体尺寸为30×18×8mm3.本文讨论了籽晶方向对Na3La9O3(BO3)8晶体生长的影响,(100)方向比(001)方向更有利于晶体生长.     

Single‐crystal growth and characterization of mullite‐type orthorhombic Bi2M4O9 (M = Al3+, Ga3+, Fe3+)

Pure and homogeneous single crystals of orthorhombic mullite‐type Bi₂M₄O₉ (M = Al³⁺, Ga³⁺, Fe³⁺), and a mixed Bi₂Fe_1.7Ga_2.3O₉ crystal from an equimolar Ga/Fe composition were grown by the top seeded solution growth (TSSG) method. All these compounds melt incongruently in the range of about 800 and 1100 °C. In case of bismuth gallate and ferrate inclusion‐free crystals with dimensions up to several cubic centimeters can be grown. Limited solubility in Bi₂O₃ and the high steepness of the liquidus curve are the reasons for getting only small imperfect bismuth aluminate crystals. In contrast to ceramic materials preparation reported in literature, divalent calcium and strontium could not be incorporated into the mullite‐type structure during the melt growth process. Several fundamental physical properties like heat capacity, thermal expansion, heat conductivity, elastic constants, high‐pressure behavior and oxygen diffusivity were determined by different research groups using single‐crystalline samples from the as‐grown materials. Furthermore, the refractive indices of Bi₂Ga₄O₉ were measured in the range of 0.430 and 0.700 μm. Such as many other bismuth containing compounds the refractive indices of Bi₂Ga₄O₉ are larger than 2, and Bi₂Ga₄O₉ is an optic biaxial positive crystal. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

溶胶-凝胶法制备Zn3Ga2Ge2O10:Cr3+0.01,Pr3+0.03,Yb3+0.3纳米长余辉材料及其表面修饰的研究

以Ga(NO3)3·8H2O、Zn(NO3)2·6H2O、Pr(NO3)2·6H2O、GeO2、Yb(NO3)3·5H2O、Cr(NO3)2·9H2O为原料,采用溶胶-凝胶法合成了Cr3+,Pr3+,Yb3+共掺杂的Zn3Ga2Ge2O10长余辉纳米材料(PLNPs).利用XRD,SEM,激发发射图谱,余辉曲线测试确定1000℃煅烧,保温3 h时,基质Zn3 Ga2 Ge2 O10已形成.Yb3+掺杂百分比为0.3时,样品的发光性能最好.Zn3 Ga2 Ge2 O10:Cr3+0.01,Pr3+0.03,Yb3+0.3纳米长余辉材料在波长为267 nm的紫外线激发下发射出中心波长为745 nm的深樱桃红色光,此时晶粒粒径约为150 nm;随着Yb3+掺杂百分比的增加,晶粒粒径逐渐变小.通过FT-IR,Zeta电势,激光粒度测试,TEM及悬浮实验测试表明,PEG修饰PLNPs后,可观察到明显的核壳结构,水合粒径约为155 nm;水溶性大大增加,0.3 mg/mL的浓度下其悬浮时间超过48 h,这表明PEG包裹PLNPs成功.     

Nb掺杂下CaTi2O4(OH)2片状结构的溶剂热制备及光催化性能研究

利用无水氯化钙-钛酸四正丁酯-无水乙醇体系,通过掺杂Nb用溶剂热法制备了CaTi2O4(OH)2片状结构.利用X射线衍射(XRD),扫描电子显微镜(SEM)和比表面积测试仪(BET)对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计分析了样品对光的吸收特性,研究掺人不同Nb量对CaTi2O4(OH)2样品的物相结构、微观形貌以及其光催化性能的影响,并考察了不同光源对所制备样品性能的影响.实验结果表明:随着Nb掺杂量的增加,样品的结晶度逐渐增加,当Nb掺杂量为6;时,CaTi2O4(OH)2片状结构结晶度达到最大值75.92;,此时在光源250 nm照射下光催化性能达到最优,进一步增加Nb掺杂量8;,光催化性能随之降低.这主要是样品的结晶度、能级和比表面积减小成为主导因素.     

C3N4-CaTi2O4(OH)2复合粉体的溶剂热制备及光催化性能

利用无水氯化钙-钛酸四正丁酯-无水乙醇体系,通过加入一定摩尔配比的C3N4粉体用溶剂热法制备了C3N4-CaTi2O4(OH)2复合材料粉体.利用X射线衍射(XRD),比表面积(BET)和扫描电子显微镜(SEM)对样品的显微结构进行检测分析,并利用紫外-可见吸收光度计分析了样品对光的吸收特性,研究不同摩尔配比的C3N4粉体复合量对CaTi2O4(OH)2样品的物相结构、微观形貌以及其光催化性能的影响,并考察了不同光源对所制备样品性能的影响.实验结果表明:C3N4粉体的引入显著提高了CaTi2O4(OH)2样品的光催化活性,且当CaTi2O4(OH)2:C3N4物质的量之比为1:0.75时,复合样品的光催化降解率在250nm光源照射下K可达到最大值0.02338min-1.     

A3BGa3Si2O14(A=Ca,Sr;B=Nb,Ta)晶体研究进展

介绍了一类性能优异、结构有序的新型材料--A3BGa3Si2O14(A=Ca,Sr;B=Nb,Ta)单晶,总结了其研究进展,并对该类晶体的生长、结构、热学、光学和压电性能进行了描述.     

MgO-Al2O3-Re2O3(Re=Lu,Y)对无压烧结Si3N4陶瓷显微结构和性能的影响

研究了MgO-Al2O3-Re2O3(Re=Lu,Y)三元烧结助剂体系对无压烧结Si3N4陶瓷显微结构和力学性能的影响.研究结果表明,添加MgO-Al2O3-Lu2O3三元助剂制备的Si3N4陶瓷显微结构具有明显的双峰分布,晶粒较粗化,致密度、硬度、弯曲强度、断裂韧性分别为96.4;、14.59 GPa、964 MPa、7.64 MPa·m1/2;而添加MgO-Al2O3-Y2O3三元助剂制备的Si3N4陶瓷具有细化的显微结构,致密度、硬度、弯曲强度、断裂韧性分别为99.9;、15.29 GPa、758 MPa、6.60 MPa·m1/2.     

Preparation and Properties of a Novel Nonlinear Optical Crystal: MnHg(SCN)4(H2O)2.2(C3H6CONCH3)

In this article, diaquatetrakis (thiocyanato) manganese(II) mercury(II)‐N‐methyl‐2‐pyrrolidone, MnHg(SCN)₄(H2O)₂.2(C₃H₆CONCH₃), (abbreviated as MMTWMP), a new organometallic nonlinear optical crystal material is reported. The structure, optical and thermal characterizations were determined by elemental analysis, infrared and Raman spectroscopy, X‐ray powder diffraction, thermogravimetric analysis, differential scanning calorimetry, special heat, SHG measurements and UV/Vis/NIR optical transmission spectra. It belongs to the tetragonal crystallographic system, with cell parameters: a = 12.1294, c = 8.2238Å, V = 1211.27ų. Single crystals with dimensions up to 8 × 7 × 5 mm³ have been obtained. The morphology of the crystals was indexed. The MMTWMP crystal exhibits good physicochemical stability at normal temperature and pressure. Its UV transparency cutoff is 360 nm, which is shifted to the violet by 13 nm, as compared with MnHg(SCN)₄ (MMTC); the optical transmission is 44.82% at 404 nm, which is by 17.46% higher than that of MMTC.