High coercivity Nd2(Fe,Co)14C-type ribbons prepared by melt spinning

Melt-spun Nd₁₃Dy₂Fe_77−xCo_xC₆B₂ (x=0, 5, 10, 15, 20) ribbons with a high coercivity more than 2 T have been obtained. It was found that the ribbons quenched at the optimum wheel speed 15 m/s (as-spun ribbons) mainly consist of ferromagnetic 2 : 14 : 1 phase and paramagnetic NdC₂ phase, and the ribbons spun at 25 m/s and subsequently annealed at 973 K for 15 min (as-annealed ribbons) are primarily composed of the magnetic 2 : 14 : 1 and 2 : 17 phases. The magnetization process of as-spun ribbons controlled by a pinning of the domain wall is different from that of as-annealed ribbons determined by a nucleation of the reverse domain. This significant difference originates possibly from the existence of paramagnetic NdC₂ phase acting as a pinning center in as-spun ribbons. In the as-annealed ribbons, the substitution of Co for Fe leads to increase of remanence (μ₀M_r), maximum energy product ((BH)_max) from 0.67 T, 9.7 MGOe for x=0 to 0.84 T, 14.4 MGOe for x=10, respectively. A coercivity of 2.74 T is obtained for as-quenched Nd₁₃Dy₂Fe_77−xCo_xC₆B₂ (x=0) ribbons.     

Hydrothermal synthesis and magnetic studies of transition metal nocerites M3(BO3)F3 (M=Fe,Co, Ni)

Polycrystalline samples of M₃(BO₃)F₃ (M=Fe, Co, Ni), isostructural with nocerite Mg₃(BO₃)(OH,F)₃, have been prepared in supercritical hydrothermal conditions. These compounds represent with boracites, M₃B₇O₁₃F (M=Mg, Cr, Mn, Fe, Co, Zn), the only transition metal fluoride borates known to date. Co₃(BO₃)F₃ and Ni₃(BO₃)F₃ are antiferromagnetic with T_N=17(2) and 40(2) K, respectively. Spin-flop transitions at B_C1=4.0 T and B_C2=7.5 T occur at 1.6 K in Co₃(BO₃)F₃, while a parasitic ferromagnetism (0.02 μ_B/Ni²⁺ at 1.6 K) appears below T_N in Ni₃(BO₃)F₃. The magnetic structures consist of three spin sub-lattices of double rutile-type ferromagnetic chains.     

Effect of grain size and magnetocrystalline anisotropy on exchange coupling in nanocomposite two-phase Nd-Fe-B magnets

We have studied the exchange coupling in two-phase nanocrystalline alloy ribbons of the composition Nd_4−xSm_xFe_77.5B_18.5 (x=0.0, 0.1, 0.2, 0.3, 0.4 and 0.5). The grain size of the Fe₃B phase changed from 16 to 23 nm by annealing between 670°C and 760°C for 5 min. From the measurements of the magnetic properties and the reversibility of magnetization, we derived that the mean critical grain size of the Fe₃B phase required for full exchange coupling by the Nd₂Fe₁₄B phase is about 20 nm. A detailed study of the magnetization-reversal process was made on samples in which the magnetocrystalline anisotropy of the Nd₂Fe₁₄B phase was reduced by substitution of Sm for Nd. We showed that the exchange-coupled range can be markedly expanded and that the reduced remanence can be increased with increasing Sm content.     

Superconductivity in bulk T′-(La,Sm)2CuO4 prepared via a molten alkaline hydroxide route

We have synthesized La_2?xSm_xCuO₄ (0 ? x ? 2.0) with the Nd₂CuO₄ structure via a molten alkaline hydroxide route at temperatures as low as 400–480 °C. After reduction heat treatment in vacuum at 600–750 °C for removal of excess oxygen atoms at the interstitial apical site, superconductivity with T_c = 20–24 K was observed in the samples with x = 0.05–1.0. The superconducting volume fraction is nearly 100% for x = 0.3–0.7. Our results demonstrate that La_2?xSm_xCuO₄ with no nominal carrier doping is a bulk superconductor.     

Polymorphic phase transition and thermal stability in squaric acid (H2C4O4)

Phase transformations in squaric acid (H₂C₄O₄) have been investigated by thermogravimetry and differential scanning calorimetry with different heating rates β. The mass loss in TG apparently begins at onset temperatures T_di=245±5 °C (β=5 °C min^?1), 262±5 °C (β=10 °C min^?1), and 275±5 °C (β=20 °C min^?1). A polymorphic phase transition was recognized as a weak endothermic peak in DSC around 101 °C (T_c⁺). Further heating with β=10 °C min^?1 in DSC revealed deviation of the baseline around 310 °C (T_i), and a large unusual exothermic peak around 355 °C (T_p), which are interpreted as an onset and a peak temperature of thermal decomposition, respectively. The activation energy of the thermal decomposition was obtained by employing relevant models. Thermal decomposition was recognized as a carbonization process, resulting in amorphous carbon.     

Structure and electrochemical properties of Sm0.5Sr0.5Co1 − xFexO3 − δ cathodes for solid oxide fuel cells

Crystal structure, thermal expansion coefficient, electrical conductivity and cathodic polarization of compositions in the system Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ with 0 ≤ x ≤ 0.9 were studied as function of Co / Fe ratio and temperature, in air. Two phases, including an Orthorhombic symmetry for 0 ≤ x ≤ 0.4 and a cubic symmetry for 0.5 ≤ x ≤ 0.9, were observed in samples of Sm_0.5Sr_0.5Co_1 − xFe_xO_3 − δ at room temperature. The adjustment of thermal expansion coefficient (TEC) to electrolyte, which is one of the main problems of SSC, could be achieved to lower TEC values with more Fe substitution. High electrical conductivity above 100 S/cm at 800 °C was obtained for all specimens, so they could be good conductors as cathodes of IT-SOFC. The polarization behavior of SSCF as a function of Fe content was evaluated by means of AC impedance using LSGM electrolyte. It was discovered that the Area Specific Resistance (ASR) of SSCF increased as the amount of substitution of Fe for Co increased. When the amount of Fe reached to 0.4, the highest ASR was obtained and then the resistance started decreasing above that. The electrode with a composition of Sm_0.5Sr_0.5Co_0.2Fe_0.8O_3 − δ showed high catalytic activity for oxygen reduction operating at temperature ranging from 700 to 800 °C.     

Crystal chemistry and physical properties of the ternary compounds RE5B4C5 (RE=Ce,Pr, Nd)

The ternary rare-earth metal boride carbides RE₅B₄C₅ (RE=Ce, Pr, Nd) were prepared by arc melting the mixtures of the pure elements and subsequent annealing at 1270 K. Their crystal structures were determined from single crystal X-ray diffraction data. They crystallize in the Ce₅B₄C₅ type of structure (space group Pna2₁, Z=8). Two new compounds were found, Pr₅B₄C₅: a=24.592(2) Å, b=8.4563(5) Å, c=8.4918(5) Å, R₁=0.043 (wR₂=0.076) for 2871 reflections with I_o?2σ(I_o)); for Nd₅B₄C₅: a=24.301(1) Å, b=8.3126(5) Å, c=8.3545(4) Å, R₁=0.035 (wR₂=0.069) for 3707 reflections with I_o?2σ(I_o)). Its structural arrangement consists of a three-dimensional framework of rare-earth atoms resulting from the stacking of slightly corrugated two-dimensional square nets, leading to voids filled with B₄C₄, B₃C₃, BC₂ finite chains and isolated carbon atoms. Ce₅B₄C₅ is an antiferromagnet at 5 K followed by a metamagnetic transition in elevated external fields. Pr₅B₄C₅ and Nd₅B₄C₅ are ferromagnets below T_C=12 and 15 K, respectively.     

High temperature properties of the n = 2 Ruddlesden–Popper phases (La,Sr)3(Fe,Ni)2O7−δ

The crystal chemistry and mixed conductor properties of the n = 2 member of the Ruddlesden–Popper (R–P) phases Sr_3−xLa_xFe_2−yNi_yO_7−δ with 0 ≤ x ≤ 0.3 and 0 ≤ y ≤ 1.0 have been studied at high temperature. High-temperature X-ray diffraction and thermogravimetric measurements of the equilibrium pO₂ (10^− 5 ≤ pO₂ ≤ 1 atm) in the temperature range 400 ≤ T ≤ 1000 °C indicate that the Sr₃FeNiO_7−δ phase is able to accommodate a large oxygen non-stoichiometry (δ ∼ 1.5) without structural transformations. The electrical conductivity and oxygen permeability increase with the substitution of Ni for Fe in the range 550 ≤ T ≤ 1000 °C. The electrical transport of the Sr₃FeNiO_7−δ phase is thermally activated and the activation energy decreases with the substitution of Ni for Fe for a given oxygen content. The increase in the oxygen permeation flux with increasing Ni content is due to an increasing oxygen non-stoichiometry and a lower activation energy for permeation.     

Defect equilibria and partial molar properties of (La,Sr)(Co,Fe)O3−δ

The oxygen nonstoichiometry δ of La_1−xSr_xCo_1−yFe_yO_3−δ (x = 0.6 and y = 0.2, 0.4) was investigated by thermogravimetry in the range 703 ≤ T/°C ≤ 903 and 1E−5 < pO₂/atm < 1. The oxygen deficit increases with increasing T and decreasing pO₂. Electronic conductivities σ were measured as a function of pO₂ in the range 1E−5 < pO₂/atm < 1 at 700 ≤ T/°C ≤ 900. At constant T, a p-type pO₂-dependence of σ is observed. Oxygen nonstoichiometry data are analyzed with regard to the enthalpy and entropy of oxidation ΔH_ox^θ and ΔS_ox^θ, as well as to the partial molar enthalpy and entropy of oxygen with respect to the standard state of oxygen (pO₂^θ = 1 atm), (h_O − H_O^θ) and (s_O − S_O^θ), respectively. For 2.67 ≤ (3 − δ) ≤ 2.79, (h_O − H_O^θ) decreases with increasing δ, while (s_O − S_O^θ) is constant within the limits of error. Defect chemical modelling was performed by an ideal solution model under consideration of three different valence states for B-site ions (Co or Fe). The dependence of σ on δ is modelled, using calculated defect concentrations as functions of δ. Deviations from the ideal behaviour suggest an immobilization of n-type charge carriers by oxygen vacancies.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting La3+ with Sm3+

The microwave dielectric properties of La_1?xSm_x(Mg_0.5Sn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La_1?xSm_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.59 g/cm³, dielectric constant (ε_r) of 19.9, quality factor (Q×f) of 70,200 GHz, and temperature coefficient of resonant frequency (τ_f) of ?77 ppm/°C were obtained for La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h. The dielectric constant, and τ_f of La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics were almost independent with the sintering temperature as the sintering temperature varied from 1450 to 1600 °C.     

Magnetic characterisation and hydrogen absorption characteristics of Pr3(Fe,Ti)29Hx

An interstitial Pr₃(Fe,Ti)₂₉ hydride was synthesised by gas-phase hydrogenation on Pr₃(Fe,Ti)₂₉ powder using H₂. The reaction kinetics between Pr₃(Fe,Ti)₂₉ and H₂ gases was studied in a constant-volume reactor. The sample starts to rapidly absorb hydrogen, interstitially, at about 533 K. Absorption passes through a maximum at about 598 K (1.6 H/f.u) and then interstitial hydrogen desorption takes place up to the temperature of 673 K. By cooling to room temperature, the sample absorbs more hydrogen, interstitially, reaching the value of 3.6 H/f.u. By remaining at room temperature, the sample absorbs even more hydrogen reaching the value of 5.2 H/f.u. The lattice expansion observed is 2.1% and the Curie temperature, T_C, increased from 392 to 518 K. The hydride exhibits saturation magnetisation, M_S, of 145.4 and 157.5 Am²/kg at room temperature (RT) and at 5 K, respectively, anisotropy field, H_A, of 2.1 T (RT) and 4.5 T (5 K) and average hyperfine field, H_eff, of 23.3 T (RT). The magnetic anisotropy of Pr₃(Fe,Ti)₂₉ hydride is the same as that of the parent compounds, easy-cone-like, changing only in the cone angle (from 34° to 26°).     

Performance of La-doped strontium titanate (LST) anode on LaGaO3-based SOFC

Ni-containing anode is currently used with many electrolytes of solid oxide fuel cells (SOFCs). However, Ni is easily oxidized and deteriorates the LaGaO₃-based electrolyte. A La-doped SrTiO₃ (LST, La_0.2Sr_0.8TiO₃) is a candidate as an anode material to solve the Ni poisoning problem in LaGaO₃-based SOFC. In this study, a single-phase LST and an LST-Gd_0.2Ce_0.8O_2 ? δ (GDC) composite were tested as the possible anodes on La_0.9Sr_0.1Ga_0.8Mg_0.2O_3 ? δ (LSGM) electrolyte. In order to further improve the anodic performance, Ni was impregnated into the LST-GDC composite anode. The performance was examined from 600 °C to 800 °C by measuring impedance of the electrolyte-supported, symmetric (anode/electrolyte/anode) cells. A polarization resistance (R_p) of LST-GDC anode was much reduced from that of LST anode. When Ni was impregnated into LST-GDC composite, the R_p value was further reduced to ~ 10% of the single-phase LST anode, and it was 1 Ωcm² at 800 °C in 97% H₂ + 3% H₂O atmosphere. A single cell with Ni-impregnated LST-GDC as an anode, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3 ? δ (BSCF) as a cathode and LSGM as an electrolyte exhibited the maximum power density of 275 mW/cm² at 800 °C, increased from ~ 60 mW/cm² for the cell using the LST-GDC as an anode. Thus, LST-GDC composite is promising as a component of anode.     

Dephenolization,dearomatization and detoxification of olive mill wastewater with sonication combined with additives and radical scavengers

In this study, the effects of some additives [manganese (III) oxide (Mn₃O₄), Cu⁺², Fe⁰ and potassium iodate (KIO₃)] and some radical scavengers [sodium carbonate (Na₂CO₃), perfluorohexane (C₆F₁₄) and t-butyl alcohol (C₄H₁₀O)] on the sonication of olive mill effluent wastewater (OMW) were investigated since the wastewaters of this industry are removed with low efficiencies. The maximum total phenol and total aromatic amines (TAAs) removal efficiencies were 88% and 79%, respectively, at 60 °C with only 150 min sonication. The maximum phenol removal was found as 98% with 19 mg L⁻¹ perfluorohexane and 5 mg L⁻¹ Fe⁰ while the maximum TAAs removal was 99% with 16 mg L⁻¹ KIO₃. Catechol, tyrosol, quercetin, caffeic acid, 4-methyl catechol, 2-phenylphenol (2-PHE) and 3-phenyl phenol (3-PHE) were detected as phenol intermediates while trimethlyaniline, aniline, o-toluidine, o-anisidine, dimethylaniline, ethylbenzene and durene were identified as TAAs in the OMW. The maximum acute toxicity removals were 96% and 99% in Vibrio fischeri and Daphnia magna, respectively. Total phenol, TAAs and the toxicity in an OMW were removed efficiently and cost-effectively through sonication.     

Synthesis and characterization of layered Li1−x(Ni0.5Co0.5)1−yFeyO2(0 ≤ (1 − x) ≤ 1 and 0 ≤ y ≤ 0.2) cathodes

Layered Li(Ni_0.5Co_0.5)_1−yFe_yO₂ cathodes with 0 ≤ y ≤ 0.2 have been synthesized by firing the coprecipitated hydroxides of the transition metals and lithium hydroxide at 700 °C and characterized as cathode materials for lithium ion batteries to various cutoff charge voltages (up to 4.5 V). While the y = 0.05 sample shows an improvement in capacity, cyclability, and rate capability, those with y = 0.1 and 0.2 exhibit a decline in electrochemical performance compared to the y = 0 sample. Structural characterization of the chemically delithiated Li_1−x(Ni_0.5Co_0.5)_1−yFe_yO₂ samples indicates that the initial O3 structure is maintained down to a lithium content (1 − x) ≈ 0.3. For (1 − x) < 0.3, while a P3 type phase is formed for the y = 0 sample, an O1 type phase is formed for the y = 0.05, 0.1 and 0.2 samples. Monitoring the average oxidation state of the transition metal ions with lithium contents (1 − x) reveals that the system is chemically more stable down to a lower lithium content (1 − x) ≈ 0.3 compared to the Li_1−xCoO₂ system. The improved structural and chemical stabilities appear to lead to better cyclability to higher cutoff charge voltages compared to that found before with the LiCoO₂ system.     

Formation of nickel and nickel,zinc-bearing ferrite in aqueous suspension by air oxidation

Stoichiometric Ni-bearing ferrite was formed by air oxidation of an iron(II) hydroxide suspension at an initial Ni : Fe_tot mol ratio (r_Ni) of 0.20 : 2.80 at pH 10.0 and 65°C. Most of products formed at r_Ni=0.40 : 2.60 and 0.60 : 2.40 were Ni-bearing ferrites, of which vacancies of Fe³⁺ ion on the lattice points may be considered. Only Ni, Zn-bearing ferrites were formed in the suspensions at initial (Ni + Zn)  : Fe_tot mol ratios (r_{Ni + Zn}) of 0.20 : 2.80–0.60 : 2.40 at pH 10.0 and 65°C. At higher r_Ni or r_{Ni + Zn} by-products containing Ni, Fe and O₄²⁻ were formed. The formation of the by-products was depressed in the suspensions containing chloride ions in the place of sulfate ions.     

Self-induced polarization rotation of laser beam in fullerene (C70) solutions

Nonlinear self-rotation of elliptically polarized laser pulses (λ = 532 nm, τ_FWHM ~ 12 ns) in toluene, benzene and binary mixture (toluene + ethanol) solutions of fullerene C₇₀ has been investigated experimentally. Absolute values and signs of the nonlinear refractive indices (n₂) and nonlinear optical susceptibilities χ⁽³⁾(ω, ? ω, ω) of C₇₀ solutions in toluene and benzene at different values of polarization ellipse (θ = 0.2 ÷ 0.8) have been determined. High-resolution transmission electron microscope studies of C₇₀ solutions showed that in toluene + ethanol mixtures ball-shaped C₇₀ clusters are formed with particle sizes in the range ~ 100 ÷ 500 nm. It has been demonstrated, that the clusters sizes depend on the C₇₀ concentration and volume fraction of ethanol in toluene. Correlation between the processes of C₇₀ clusters formation in solutions and the values of polarization self-rotation angle of transmitted laser beam has been demonstrated. Physical mechanisms of laser induced optical activity in fullerene solutions have been discussed.     

Synthesis of Sm2Co17 alloy nanoparticles by mechanochemical processing

Sm₂Co₁₇ alloy nanoparticles of 10–250 nm in size were prepared by mechanochemical processing involving the co-reduction of Sm₂O₃ and CoO with Ca. The crystal structure of the nano-sized Sm₂Co₁₇ particles was mainly of the ordered Th₂Zn₁₇-type. When embedded in the CaO matrix the Sm₂Co₁₇ nanoparticles exhibited a high coercivity of 14.2 kOe. The CaO by-product could be removed by a carefully controlled washing process without significant oxidation of the ultrafine alloy particles. After washing, the cold-pressed powder exhibited a coercivity value of 11.8 kOe and a maximum magnetization of 92.0 emu/g under an applied field of 50 kOe.     

Tuneability of Sm(1 − x)CexFeO3 ± λ perovskites: Thermal stability and electrical conductivity

Trimetallic perovskite oxides, Sm_(1 ? x)Ce_xFeO_3 ± λ (x = 0–0.05), were prepared by thermal decomposition of amorphous citrate precursors followed by calcinations. The material properties of the substituted perovskites were characterized by X-ray diffraction (XRD), X-ray florescence spectroscopy (XRF), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The doped materials exhibited a single perovskite phase in air up to 1350 °C and have specific surface areas in the range of 2.696–8.665 m²/g. In reducing atmosphere (5%v/vH₂/N₂), the unsubstituted perovskite (x = 0) decomposed into two phases while the ceria stabilized materials (x = 0.01, x = 0.03, x = 0.05) remained in a single phase as revealed by XRD analysis. Their conductivities were measured by the four point probe method in air and in dilute hydrogen (5%v/vH₂/N₂) separately. The ceria substituted materials show increased stability versus reduction and phase separation for a wide temperature range (up to 1000 °C). Although undoped SmFeO₃ has higher conductivity under oxidizing conditions than ceria doped SmFeO₃ due its p-type nature, the situation is reversed under reducing conditions. The ceria substituted perovskites (Sm_(1 ? x)Ce_xFeO_3 ± λ, x = 0–0.05) showed higher conductivity in reducing than in oxidizing conditions, suggesting that ceria doping at the A-site has changed the SmFeO₃ from p-type to n-type semi-conducting behavior.     

Structural and electronic properties of group III Rich In0.53Ga0.47As(001)

The structural and electronic properties of group III rich In_0.53Ga_0.47As(001) have been studied using scanning tunneling microscopy/spectroscopy (STM/STS). At room temperature (300 K), STM images show that the In_0.53Ga_0.47As(001)–(4 × 2) reconstruction is comprised of undimerized In/Ga atoms in the top layer. Quantitative comparison of the In_0.53Ga_0.47As(001)–(4 × 2) and InAs(001)–(4 × 2) shows the reconstructions are almost identical, but In_0.53Ga_0.47As(001)–(4 × 2) has at least a 4× higher surface defect density even on the best samples. At low temperature (77 K), STM images show that the most probable In_0.53Ga_0.47As(001) reconstruction is comprised of one In/Ga dimer and two undimerized In/Ga atoms in the top layer in a double (4 × 2) unit cell. Density functional theory (DFT) simulations at elevated temperature are consistent with the experimentally observed 300 K structure being a thermal superposition of three structures. DFT molecular dynamics (MD) show the row dimer formation and breaking is facilitated by the very large motions of tricoodinated row edge As atoms and z motion of In/Ga row atoms induced changes in As–In/Ga–As bond angles at elevated temperature. STS results show there is a surface dipole or the pinning states near the valence band (VB) for 300 K In_0.53Ga_0.47As(001)–(4 × 2) surface consistent with DFT calculations. DFT calculations of the band-decomposed charge density indicate that the strained unbuckled trough dimers being responsible for the surface pinning.     

Defect interactions in La0.3Sr0.7Fe(M′)O3−δ (M′ = Al,Ga) perovskites: Atomistic simulations and analysis of p(O2)-T-δ diagrams

Atomistic modelling showed that a key factor affecting the p(O₂) dependencies of point defect chemical potentials in perovskite-type La_0.3Sr_0.7Fe_1−xM′_xO_3−δ (M′ = Ga, Al; x = 0–0.4) under oxidizing conditions, relates to the coulombic repulsion between oxygen vacancies and/or electron holes. The configurations of A- and B-site cations with stable oxidation states have no essential influence on energetics of the mobile charge carriers, whereas the electrons formed due to iron disproportionation are expected to form defect pair clusters with oxygen vacancies. These results were used to develop thermodynamic models, adequately describing the p(O₂)-T-δ diagrams of La_0.3Sr_0.7Fe(M′)O_3−δ determined by the coulometric titration technique at 923–1223 K in the oxygen partial pressure range from 1 × 10^− 5 to 0.5 atm. The thermodynamic functions governing the oxygen intercalation process were found independent of the defect concentration. Doping with aluminum and gallium leads to increasing oxygen deficiency and induces substantial changes in the behavior of iron cations, increasing the tendencies to disproportionation and hole localization. Despite similar oxygen nonstoichiometry in the Al- and Ga-substituted ferrites at a given dopant content, the latter tendency is more pronounced in the case of aluminum-containing perovskites.