Surface‐enhanced Raman scattering and fluorescence emission of gold nanoparticle–multiwalled carbon nanotube hybrids

Multiwalled carbon nanotubes (MWCNTs) are grafted with gold (Au) nanoparticles of different sizes (1–12 and 1–20 nm) to form Au–MWCNT hybrids. The Au nanoparticles pile up at defect sites on the edges of MWCNTs in the form of chains. The micro‐Raman scattering studies of these hybrids were carried using visible to infrared wavelengths (514.5 and 1064 nm). Enhanced Raman scattering and fluorescence is observed at an excitation wavelength of 514.5 nm. It is found that the graphitic (G) mode intensity enhances by 10 times and down shifts by approximately 3 cm⁻¹ for Au–MWCNT hybrids in comparison with pristine carbon nanotubes. This enhancement in G mode due to surface‐enhanced Raman scattering effect is related to the interaction of MWCNTs with Au nanoparticles. The enhancement in Raman scattering and fluorescence for large size nanoparticles for Au–MWCNTs hybrids is corroborated with localized surface plasmon polaritons. The peak position of localized surface plasmons of Au nanoparticles shifts with the change in environment. Further, no enhancement in G mode was observed at an excitation wavelength of 1064 nm. However, the defect mode (D) mode intensity enhances, and peak position is shifted by approximately 40 cm⁻¹ to lower side at the same wavelength. The enhanced intensity of D mode at 1064 nm excitation wavelength is related to the double resonance phenomenon and shift in the particular mode occurs due to more electron phonon interactions near Fermi level. Copyright © 2012 John Wiley & Sons, Ltd.     

Semi-quantitative Surface Enhanced Raman Scattering Spectroscopic Creatinine Measurement in Human Urine Samples

This paper presents the development of a semi-quantitative method of measuring the creatinine biomolecule in human urine by the surface enhanced Raman scattering (SERS) technique. Creatinine is one of the major components of urine and can be used to represent the metabolic and renal function of the human body. The Raman signal of creatinine is enhanced by 50 nm Au nanoparticles. Raman spectra between 1400 and 1500 cm^?1 were analyzed to obtain the relationship between the SERS band area and creatinine concentration. The square of the correlation coefficient is 0.99 in artificial urine over the creatinine range 38.4–153.6 mg/dl. In a human urine experiment, a good linear correlation is observed over the creatinine concentration range 2.56–6.4 mg/dl. The square of correlation coefficient is 0.96.     

Au@SiO2 core/shell nanoparticle assemblage used for highly sensitive SERS‐based determination of glucose and uric acid

The use of Au@SiO₂ core/shell nanoparticle (NP) assemblage with highly sensitive surface‐enhanced Raman scattering (SERS) was investigated for the determination of glucose and uric acid in this study. Rhodamine 6G dye molecules were used to evaluate the SERS enhancement factor for the synthesized Au@SiO₂ core/shell NPs with various silica shell thicknesses. The enhancement of SERS signal from Rhodamine 6G was found to increase with a decrease in the shell thickness. The core/shell assemblage with silica layer of 1–2 nm over a Au NP of ~36 nm showed the highest SERS signal. Our results show that the SERS technique is able to detect glucose and uric acid within wide concentration ranges, i.e. 20 ng/dL to 20 mg/dL (10⁻¹²–10⁻³ M) and 16.8 ng/dL to 2.9 mg/dL (10⁻¹¹–1.72 × 10⁻⁴ M), respectively, with associated lower detection limits of ~20 ng/dL (~1.0 × 10⁻¹² M) and ~16.8 ng/dL (~1.0 × 10⁻¹¹ M). Our work offers a low‐cost route to the fabrication of agile sensing devices applicable to the monitoring of disease progression. Copyright © 2013 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering study of the red dye laccaic acid

FT‐Raman and surface‐enhanced Raman scattering (SERS) spectroscopy were applied to the study of lac dye, a highly fluorescent anthraquinone red dye. The SERS spectra were obtained at different pH values, on Ag nanoparticles prepared by chemical reduction with citrate and hydroxylamine, and at several excitation wavelengths, in order to find the best experimental conditions for the detection of the lac dye. The lower detection limit was achieved using nanoparticles prepared by reduction with hydroxylamine, excitation at 514.5 nm, and slightly acidic pH conditions, thus exploiting a combination of factors including lower electrostatic repulsion between dye and nanoparticles and resonance Raman enhancement. A comparison between the adsorption of laccaic acid (LA) and carminic acid (CA), another anthraquinone red dye, was also done, based on the SERS spectra of both dyes. Copyright © 2007 John Wiley & Sons, Ltd.     

Single‐molecule surface‐enhanced Raman scattering of fullerene C60

We achieved single‐molecule surface‐enhanced Raman scattering (SM‐SERS) spectra from ultralow concentrations (10⁻¹⁵ M) of fullerene C₆₀ on uniformly assembled Au nanoparticles. It was found that resonant excitation at 785 nm is a powerful tool to probe SM‐SERS in this system. The appearance of additional bands and splitting of some vibrational modes were observed because of the symmetry reduction of the adsorbed molecule and a relaxation in the surface selection rules. Time‐evolved spectral fluctuation and ‘hot spot’ dependence in the SM‐SERS spectra were demonstrated to result from the single‐molecule Raman behavior of the spherical C₆₀ on Au nanoparticles. Copyright © 2010 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman scattering studies of carbon nanotubes using Ag‐core Au‐shell nanoparticles

Surface‐enhanced Raman scattering from carbon nanotube bundles adsorbed with plasmon‐tunable Ag‐core Au‐shell nanoparticles (Ag@Au nps) was carried out for the first time. By utilizing nanoparticles whose plasmon resonance peak (541, 642 nm) closely matches the commonly used Raman excitation sources (532, 632.81 nm), we can observe a large enhancement in the Raman signatures of carbon nanotubes. We obtain greater enhancement in the Raman signal for the above case when compared to nanotubes adsorbed with conventional Ag, Au or other ‘off resonant’ Ag@Au nps. The power‐dependent SERS experiment on single‐walled nanotubes (SWNTs) with resonant Ag@Au nps reveals a linear behavior between the G‐band intensity and the photon flux density, which is in agreement with the vibrational pumping model of SERS. The observed enhancement by resonance matching is pronounced for carbon nanotubes and may lead to insights into understanding nanotube–nanoparticle interaction. Copyright © 2009 John Wiley & Sons, Ltd.     

Improved performances on surface‐enhanced Raman scattering based on electrochemically roughened gold substrates modified with SiO2 nanoparticles

In this work, we use electrochemical oxidation–reduction cycles (ORC) methods to prepare surface‐enhanced Raman scattering (SERS)‐active gold substrates modified with SiO₂ nanoparticles to improve the corresponding SERS performances. Based on the modified substrates, the SERS of Rhodamine 6G (R6G) exhibits a higher intensity by 3‐fold of magnitude, as compared with that of R6G adsorbed on a SERS‐active Au substrate without the modification of SiO₂ nanoparticles. Moreover, the SERS enhancement capabilities of the modified and the unmodified Au substrates are seriously destroyed at temperatures higher than 250 and 200 °C, respectively. These results indicate that the modification of SiO₂ nanoparticles can improve the thermal stability of SERS‐active substrates. The aging in SERS intensity is also depressed on this modified Au substrate due to the contribution of SiO₂ nanoparticles to SERS effects. Copyright © 2009 John Wiley & Sons, Ltd.     

A hybrid substrate for surface‐enhanced Raman scattering spectroscopy: coupling metal nanoparticles to strong localised fields on a micro‐structured surface

Electromagnetic coupling between localised plasmons on metal nanoparticles and the strong localised fields on a micro‐structured surface is demonstrated as a means to increase the enhancement factor in surface‐enhanced Raman scattering (SERS) spectroscopy. Au nanoparticles of diameter 20 nm were deposited on a micro‐structured Au surface consisting of a periodic array of square‐based pyramidal pits (Klarite). The spectra of 4‐aminothiophenol (4‐ATP) were compared before and after deposition of Au nanoparticles on the micro‐structured surface. The addition of Au nanoparticles is shown to provide significantly higher signal intensities, with improvements of the order of ∼10³ per molecule compared with spectra obtained from the micro‐structured substrate alone. This hybrid approach offers promise for combining nanoparticles with micro‐ and nano‐structured surfaces in order to design SERS substrates with higher sensitivities. Copyright © 2011 John Wiley & Sons, Ltd.     

Multifunctional Plasmonic Co‐Doped Fe2O3@polydopamine‐Au for Adsorption,Photocatalysis, and SERS‐based Sensing

A new type of multifunctional plasmonic nanoparticles, cobalt‐doped Fe₂O₃@polydopamine‐Au (Co‐Fe₂O₃@PDA‐Au), is fabricated via coating PDA through self‐polymerization onto Co‐Fe₂O₃ and further loading gold nanoparticles by in situ reduction onto the surface of PDA shell. Benefiting from the universal adhesive ability of PDA and negative zeta potetntial of the composite, the Co‐Fe₂O₃@PDA‐Au shows strong adsorptivity for cationic dyes. The presence of gold nanoparticle with the diameter of 15 nm in the Co‐Fe₂O₃@PDA‐Au system promotes surface‐enhanced Raman scattering (SERS) activity with an impressive detection limit of 1 × 10^?6 m . Thanks to the synergistic effect of the light harvesting of PDA, the surface plasmon resonance of Au, and the electron conductibility of PDA and Au, the Co‐Fe₂O₃@PDA‐Au exhibits an enhanced photocatalytic activity comparing with unmodified Co‐Fe₂O₃. All the above‐mentioned functions enable Co‐Fe₂O₃@PDA‐Au to be a multifunctional material system for various applications toward environmental pollutants.     

Poly(vinylpyrrolidone)‐stabilized silver nanoparticles for strained‐silicon surface enhanced Raman spectroscopy

Poly(vinylpyrrolidone)‐stabilized silver nanoparticles deposited onto strained‐silicon layers grown on graded Si_1−xGe_x virtual substrates are utilized for selective amplification of the Si–Si vibration mode of strained silicon via surface‐enhanced Raman scattering spectroscopy. This solution‐based technique allows rapid, highly sensitive and accurate characterization of strained silicon whose Raman signal would usually be overshadowed by the underlying bulk SiGe Raman spectra. The analysis was performed on strained silicon samples of thickness 9, 17.5 and 42 nm using a 488 nm Ar⁺ micro‐Raman excitation source. The quantitative determination of strained‐silicon enhancement factors was also made. Copyright © 2011 John Wiley & Sons, Ltd.     

Self‐Assembly of Functionalized Gold Nanoparticles with Rigid and Flexible Multifunctional Linkers

The interparticle spacing of carboxyl functionalized gold nanoparticles (Au–COOH) was mediated by rigid cross‐linkers, octa(3‐aminopropyl)octasilsesquioxane (POSS–NH₃ ⁺) and poly(amidoamine) dendrimer terminated with hydroxyl groups (PAMAM–OH), and a flexible polymeric linker, poly(hexanyl viologen) (6‐VP). Regular interparticle spacing was achieved by utilizing POSS–NH₃ ⁺ and PAMAM–OH dendrimer as cross‐linkers, whereas size growth of Au–COOH was observed featuring no interparticle spacing by utilizing 6‐VP as the cross‐linker.     

Single‐molecule detection of thionine on aggregated gold nanoparticles by surface enhanced Raman scattering

We report observations of single‐molecule detection of thionine and its dynamic interactions on aggregated gold nanoparticle clusters using surface enhanced Raman scattering (SERS). Spectral intensities were found to be independent of the size of Au nanoparticles studied (from 17 to 80 nm) at thionine concentration below 10⁻¹² M or at single‐molecule concentration levels. Raman line separations and, in particular, spectral fluctuations and blinking were also observed, suggesting temporal changes in single molecular motion and/or arrangements of thionine on Au nanoparticle surfaces. In contrast, by using dispersed Au nanoparticles, only ensemble SERS spectra could be observed at relatively high concentrations (> 10⁻⁸ M thionine), and spectral intensities varied with the size of Au nanoparticles. Copyright © 2007 John Wiley & Sons, Ltd.     

Efficient photodegradation of methylthioninium chloride dye in aqueous using barium tungstate nanoparticles

BaWO₄ nanoparticles were successfully used as the photocatalysts in the degradation of methylthioninium chloride (MTC) dye at different pH levels of aqueous solution. Pure phase of barium tungstate (BaWO₄) nanoparticles was synthesized by modified molten salt process at 500 °C for 6 h. Structural and morphological characterizations of BaWO₄ nanoparticles (average particle size of ~40 nm) were studied in details using powder x-ray diffraction (XRD), FTIR, Raman, energy-dispersive, electron microscopic, and x-ray photoelectron spectroscopy (XPS) techniques. Direct band gap energy of BaWO₄ nanoparticles was found to be ~3.06 eV from the UV–visible absorption spectroscopy followed by Tauc’s model. Photocatalytic properties of the nanoparticles were also investigated systematically for the degradation of MTC dye solution in various mediums. BaWO₄ nanoparticles claim the significant enhancement of the photocatalytic degradation of aqueous MTC dye to non-hazardous inorganic constitutes under alkaline, neutral, and acidic mediums.

Open image in new window

Graphical abstract BaWO₄ nanoparticles enhance the rate of photocatalytic degradation of organic dyes in various mediums.

     

Stilbazolium merocyanine dye determination in different solutions,concentrations and colloids using SERS

Surface‐enhanced Raman scattering (SERS) measurements were carried out on stilbazolium merocyanine dye in methanol and pyridine solvents. Both solutions were measured in a series of concentrations covering a range of 5 × 10⁻⁵ M to 5 × 10⁻⁸ M . In these measurements, Ag and Au colloids were used, and the results have shown that Ag colloids yield better enhancement in the Raman spectra of this dye. Moreover, the effect of adding NaCl solution to the SERS samples was also studied. All measurements were carried out using the state‐of‐the‐art ChiralRaman instrument, which utilizes a 532 nm laser source. We report here on the success of using SERS to obtain Raman spectra of merocyanine dye at very low concentrations in an attempt to find a new approach that can be used for further investigations of the dye. The SERS spectra are reported here, and the results from different solutions, colloids, concentrations and pH values are compared. Copyright © 2006 John Wiley & Sons, Ltd.     

Catalytic reduction of organic dyes at gold nanoparticles impregnated silica materials: influence of functional groups and surfactants

Gold nanoparticles (Au NPs) in three different silica based sol–gel matrixes with and without surfactants are prepared. They are characterized by UV–vis absorbance and transmission electron microscopic (TEM) studies. The size and shape of Au NPs varied with the organo-functional group present in the sol–gel matrix. In the presence of mercaptopropyl functionalized organo-silica, large sized (200–280 nm) spherical Au NPs are formed whereas in the presence of aminopropyl functionalized organo-silica small sized (5–15 nm) Au NPs are formed inside the tube like organo-silica. Further, it is found that Au NPs act as efficient catalyst for the reduction of organic dyes. The catalytic rate constant is evaluated from the decrease in absorbance of the dye molecules. Presence of cationic or anionic surfactants greatly influences the catalytic reaction. The other factors like hydrophobicity of the organic dyes, complex formation of the dyes with anionic surfactants, repulsion between dyes and cationic surfactant, adsorption of dyes on the Au NPs also play important role on the reaction rate.     

Individual SERS substrate with core–satellite structure decorated in shrinkable hydrogel template for pesticide detection

Individual Au@PNIPAM/Ag composite has been designed and fabricated as surface‐enhanced Raman scattering (SERS) substrate in this paper. Because of the high porosity of the polymer shell and the driving force of the Au core to Ag⁺(H₂O)_n (n = 1–4) in aqueous solution, chemical reactions can be carried out while aggregation is completely avoided. Also, this makes the formation of vast and monodisperse Ag nanoparticles within PNIPAM and increases the colloidal stability. The Au cores with different sizes and the vast Ag nanoparticles then form core–satellite structures that can generate plasmon resonance. Moreover, this kind of individual Au@PNIPAM/Ag composite can be seen directly through Raman optical microscope, and uncertain effects on SERS signals resulting from variability of the configurations are minimized because these individual composite particles are relatively uniform. Importantly, the gaps between the Au and Ag nanoparticles can decrease because the PNIPAM shrinks from swollen to collapse state, so the substrate can also be used for inspecting pesticide residues accurately and rapidly. Copyright © 2014 John Wiley & Sons, Ltd.     

Size-controlled growth of gold nanoparticle-doped carbon foams as sensitive electrochemical sensors for the determination of Pb(II)

A sensitive and selective electrochemical Pb²⁺ sensor consisting of a gold-carbon foam/chitosan/gold (Au-CFs/Chit/Au)-modified electrode was prepared. The electrode was synthesized via an oil-in-water emulsion polymerization and carbonization approach. Phenolic resins were used as a carbon source. HAuCl₄ was used as a gold source and as an acidic catalyst. Melamine was used as a coordination and coupling agent to control the size of the Au nanoparticles (AuNPs). The morphologies and microstructures of the Au-CFs were characterized using scanning electron microscopy, X-ray diffraction, and transmission electron microscopy. The results revealed that the carbon foams contained interconnected macropores with diameters of nearly 5.0 μm and AuNPs with mean diameters of approximately 20.0, 9.0, and 7.0 nm. Brunauer–Emmett–Teller analysis revealed that the biggest surface area is 653.82 m²/g for Au/CFs-7. The electrochemical properties of modified electrodes and their responses to Pb²⁺ were characterized using cyclic voltammetry and differential pulse anodic stripping voltammetry. The influence of the test conditions were studied to optimize operational parameters such as the choice of supporting electrolyte, pH, deposition potential, and deposition time. Under optimal conditions, typical Au/CFs-7-modified gold electrodes exhibited an excellent electrochemical response for Pb²⁺ with a wide linear response range from 0.01 to 1.2 μM, a correlation coefficient of 0.995, and a lower limit of detection of 0.63 nM with deposition time of 180 s (S/N?=?3).     

Theoretical and experimental studies on the adsorption behavior of thiophenol on gold nanoparticles

FT‐Raman spectra were obtained for thiophenol (TP) and TP on gold nanoparticles. All vibrational fundamentals for the TP molecule are assigned on the basis of the scaled quantum force field procedure. Three model systems are studied and compared for the interactions of TP with the Au atom: (1) TP with a Au atom, C₆H₅SH Au; (2) TP anion with a Au atom, C₆H₅S⁻ Au; and (3) TP with a Au atom and subsequent formation of thiophenylate, C₆H₅SAu. The equilibrium structures and Raman spectra were calculated for the model systems using density functional theory (DFT) with the B3LYP functionals and the mixed basis set 6‐311 + G** (for C, S, H) and LANL2DZ (for Au), and theoretical Raman wavenumbers of C₆H₅SAu and C₆H₅S⁻ Au were assigned according to potential energy distributions. The third model system is shown to be preferred over the other two. The calculated binding energies are also shown to support the third model system. It is suggested that a simple model, such as the one used in the present study, is reasonable to describe surface‐enhanced Raman spectroscopy of thiophenol adsorbed on gold nanoparticles. Copyright © 2007 John Wiley & Sons, Ltd.     

Protein adsorption drastically reduces surface‐enhanced Raman signal of dye molecules

There is an increasing interest in developing surface enhancement Raman spectroscopy methods for intracellular biomolecule and for in vitro protein detection that involve dye or protein–dye conjugates. In this work, we have demonstrated that protein adsorption on silver nanoparticle (AgNP) can significantly attenuate the surface‐enhanced Raman spectroscopy (SERS) signal of dye molecules in both protein/dye mixtures and protein/dye conjugates. SERS spectra of 12 protein/dye mixtures were acquired using 4 proteins [bovine serum albumin (BSA), lysozyme, trypsin, and concanavalin A] and three dyes [Rhodamine 6G, adenine, and fluorescein isothiocyanate (FITC)]. Besides the protein/dye mixtures, spectra were also obtained for the free dyes and four FITC‐conjugated proteins. While no SERS signal was observed in protein/FITC mixtures or conjugates, a significantly reduced SERS intensity (up to 3 orders of magnitude) was observed for both R6G and adenine in their respective protein mixtures. Quantitative estimation of the number of dye molecules absorbed onto AgNP implied that the degree of R6G SERS signal reduction in the R6G/BSA sample is 2 to 3 orders of magnitude higher than what could be accounted for by the difference in the amount of the absorbed dyes. This finding has significant implications for both intracellular SERS analyses and in vitro protein detection using SERS tagging strategies that rely on Raman dyes as reporter molecules. Copyright © 2009 John Wiley & Sons, Ltd.     

Fabrication and surface enhanced Raman spectroscopy of single Au@SiO2 dimers linked by benzenedithiol

Metal nanoparticle dimers with controllable gap distance have attracted considerable attention because of their promising application in plasmonics. Generally, gaps with nanometer or subnanometer dimensions generate localized surface plasmon resonance (LSPR) coupling effect, thus contributing to a strong electromagnetic field for improving surface enhanced Raman scattering (SERS) effect. Here, we developed a facile approach to fabricate Au@SiO₂ dimers through the steric hindrance effect, in which the SiO₂ shell functioned as a block and a rigid dithiol molecule was employed as linker. The thickness of the SiO₂ shell played a critical role in improving the yield of dimers. The dimerization efficiency increased significantly as the shell thickness decreased to ~1 nm. When 1,4‐benzenedithiol was used as linker molecule, the yield of dimers was ~30%. Few dimers were obtained when mecaptobenzonic acid was used as linker. A thicker shell is associated with a low yield of dimer, whereas a thinner shell resulted in the formation of multimers and linear structures. The low number of linker molecules on the exposed area of monodisperse single nanoparticles and the lack of LSPR coupling effect (‘hot spots’) resulted in the disappearance of SERS signals of the linkers. The estimated SERS enhancement factor was about eight fold because of the strong coupling effect in the gap of the dimer with the distance of the dithiol molecular length. From the above results, SERS combined with SEM could be developed into powerful tools for monitoring the formation of dimers and positioning of single dimers. It may aid the control of assembly of Au nanoparticles and in probing key issues about SERS enhancements. Copyright © 2015 John Wiley & Sons, Ltd.