Visible up-conversion and NIR luminescence studies of LiAl<Subscript>5</Subscript>O<Subscript>8</Subscript>:Er phosphor co-doped with Yb<Superscript>3+</Superscript> and Zn<Superscript>2+</Superscript>

The frequency up-conversion, an efficient laser emission and amplification in Er³⁺:LiAl₅O₈ phosphors co-doped with Yb³⁺ and Zn²⁺ phosphor powders in the 520–560, 640–680 nm regions and at ∼1.5 μm, respectively, have been reported. The emission corresponds to the ²H_11/2, ⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions upon direct excitation into the intermediated ⁴I_11/2 level using ∼980 nm radiation from a CW laser. Possible mechanisms involved for the up-conversion processes based on the energy level matching scheme, the pump-power dependence and the dynamical behaviour have been discussed. The effect of the addition of Yb³⁺ and Zn²⁺ for the amplification in the 1.5 μm eye-safe telecommunication window has been elaborated and characterized in detail.     

Er3+-doped sol–gel SnO2 for optical laser and amplifier applications

Erbium-doped tin dioxide (SnO₂:Er³⁺) was obtained by the sol–gel method. Spectroscopic properties of the SnO₂:Er³⁺ are analyzed from the Judd–Ofelt (JO) theory. The JO model has been applied to absorption intensities of Er³⁺ (4f¹¹) transitions to establish the so-called Judd–Ofelt intensity parameters: Ω₂, Ω₄, and Ω₆. With the weak spectroscopic quality factors Ω₄/Ω₆, we expect a relatively prominent infrared laser emission. The intensity parameters are used to determine the spontaneous emission probabilities of some relevant transitions, the branching ratios, and the radiative lifetimes of several excited states of Er³⁺. The emission cross section (1.31×10^-20 cm²) is evaluated at 1.54 μm and was found to be relatively high compared to that of erbium in other systems. Efficient green and red up-conversion luminescence were observed, at room temperature, using a 798-nm excitation wavelength. The green up-conversion emission is mainly due to the excited state absorption from ⁴ I _11/2, which populates the ⁴ F _3/2,5/2 states. The red up-conversion emission is due to the energy transfer process described by Er³⁺ (⁴I_13/2)+Er³⁺(⁴I_11/2)→Er³⁺(⁴F_9/2)+Er³⁺ (⁴ I _15/2) and the cross-relaxation process. The efficient visible up-conversion and infrared luminescence indicate that Er³⁺-doped sol–gel SnO₂ is a promising laser and amplifier material. PACS 71.20.Eh; 74.25.Gz; 78.55.-m     

Infrared, visible and upconversion emission of CaAl12O19 powders doped with Er3+, Yb3+ and Mg2+ ions

CaAl₁₂O₁₉ powders doped with Er³⁺, Yb³⁺, and Mg²⁺ ions have been prepared by a low-temperature combustion synthesis technique. Formation and chemical compositions were analysed by powder X-ray diffraction and energy-dispersive spectroscopy. The visible luminescence spectra of the doped phosphor upon excitation with ∼378 nm radiation from a Xenon lamp have been studied. A broad band emission in the range of 1400–1700 nm with a peak around 1.5 μm and FWHM of about ∼80 nm responsible for the eye-safe telecommunication window has been observed upon direct excitation with a NIR laser into the ⁴I_11/2 level of Er³⁺. The effect of co-doping with Yb³⁺ and Mg²⁺ ions in the CaAl₁₂O₁₉:Er³⁺ matrix on the photoluminescence intensity corresponding to the ²H_11/2,⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions of Er³⁺ is elaborated and discussed in detail.     

Intense Upconversion Luminescence of Yb<Superscript>3+</Superscript>-Er<Superscript>3+</Superscript> in Li<Subscript>2</Subscript>O Content Tungsten-tellurite Glasses

The Er³⁺ -Yb³⁺ codoped in Li₂O content tungsten -tellurite (TWL) transparent glasses are synthesized and measured the absorption, Raman and upconversion luminescence (UPL) spectra. At room temperature intense green emission peak at 560 nm ( ⁴S_3/2→⁴I_15/2) and red emission peak at 670 nm ( ⁴F_9/2→⁴I_15/2) of Er³⁺ observed even at minimum 86 mW pumping power of infrared 980 nm excitation. For structure of the TWL glass, Raman spectrum result revealed that an important role of WO₃ in the formation of glass network linkage with Li₂O. Under this influence estimated lifetime of the ⁴I_11/2 of Er³⁺ was 1.89 μs and due to lower phonon energy of the glass produce strong upconversion signal. The effect of Er₂O₃ concentration on emission intensity result indicated that green emission intensity initially increase in compare to red emission. Under the 980 nm pump power variation measured the relatively increases the red emission to the green emission intensity and analyze the possible upconversion mechanism and process.     

Luminescence of transparent glass ceramics containing Er<Superscript>3+</Superscript> and Yb<Superscript>3+</Superscript> zirconate-titanate nanocrystals

Luminescence regularities have been studied in new erbium/ytterbium materials based on glasses and glass ceramics of a magnesium-aluminosilicate system containing nanoscale erbium/ytterbium zirconate titanate crystals with the pyrochlore structure. Lifetimes of Yb³⁺ and Er³⁺ ions in the ² F_5/2 state and in the ⁴I_11/2 and ⁴I_13/2 states, respectively, and the efficiency of Yb³⁺ → Er³⁺ energy transfer have been evaluated. The identified spectral-luminescent characteristics of the studied glasses and glass ceramics co-doped with erbium and ytterbium ions show that these materials are promising media for producing laser generation in the spectral range around 1.5 μm.     

Spectroscopic properties of fluorophosphate glass with high Er<Superscript>3+</Superscript> concentration

Fluorophosphate glass with 4 mol. % ErF₃ content was prepared. The different scanning calorimetry was conducted. Raman spectrum, infrared transmission spectrum, absorption spectrum were measured. Fluorescence spectrum and lifetime of emission around 1.53 μm were measured under 970 nm laser diode excitation. The metaphosphate content in the composition is limited, but the maximum phonon energy of glass amounts to 1290 cm^-1, and is comparatively high. The full width at half maximum is about 56 nm, and is wider than for most of the materials investigated. The measured lifetime of ⁴ I _13/2→⁴ I _15/2 transition, contributed by the high phonon energy, inefficient interaction of Er³⁺ ions, and low water content, amounts to no less than 7.36 ms though the Er³⁺ concentration is high. This work might provide useful information for the development of compact optical devices. PACS 78.20.-e; 42.70.Ce; 42.70.Hj; 32.70.Cs     

Polarized spectral properties of Er<Superscript>3+</Superscript> ions in NaGd(WO<Subscript>4</Subscript>)<Subscript>2</Subscript> crystal

Polarized spectral properties of Er³⁺:NaGd(WO₄)₂ single crystal are reported. The crystal was grown by the Czochralski method. The Judd–Ofelt theory was applied to analyze the polarized absorption spectra and then calculate the spontaneous emission probabilities, radiative lifetimes, and branching ratios. Fluorescence decay curves of the ⁴ I _13/2, ⁴ I _11/2, and ⁴ S _3/2 multiplets for the Er³⁺ ions were measured. Stimulated emission cross-sections of the ⁴ I _13/2→⁴ I _15/2 transition obtained by the Fuchtbauer–Ladenberg formula and the reciprocity method were compared. Multi-phonon relaxation rates of the crystal were estimated. Green up-conversion fluorescence around 531 and 552 nm was observed, and the possible up-conversion mechanisms were proposed. PACS 78.20.-e; 42.70.Hj     

The kinetic limitation of anti-stokes luminescence of Er3+ and Yb3+ doped infrared upconversion materials

Infrared-to-visible wave-length conversion in the Yb³⁺−Er³⁺ doped phosphors system has been described by a simple three level model based on two ions mechanism. The excitation in the range of 900–1000 nm of an IR-photon is first absorbed by Yb³⁺ ion as a sensitizer attributed to the resonant energy transition in Er³⁺ ion from ⁴ I _3/2 → ⁴ S _15/2 and ¹ F _9/2 → ⁴ I _15/2, respectively for green and red emission. The essential energy transfer processes in this system i.e. upconversion from ⁴ I _11/2 and ¹ I _13/2, cross-relaxation from ⁴ S _3/2 and ¹ F _9/2 are taken into account. The limitations of the rate-equation approach are examined with a focus on the underlying dynamics of this rare-earth system.     

Visible upconversion and infrared luminescence investigations of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powders doped with Er<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> and Zn<Superscript>2+</Superscript> ions

Alumina (Al₂O₃) powders doped with Er³⁺, Yb³⁺ and Zn²⁺ ions have been prepared by a low-temperature combustion synthesis technique. The phase purity and crystalline structure of the combustion products are confirmed by powder X-ray diffraction. An efficient frequency upconversion in the visible region and the emission in the infrared (IR) region respectively corresponding to the ²H_11/2, ⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions upon direct excitation with a CW laser lasing at ∼980 nm are discussed. The enhancement observed in the intensity of the upconversion emission bands in the visible region and the emission band in the IR region due to the presence of Yb³⁺ and Zn²⁺ in Er³⁺:Al₂O₃ powders is reported and explained in detail.     

Infrared emissions, visible up-conversion, thermoluminescence and defect centres in Er3Al5O12 phosphor obtained by solution combustion reaction

The Er₃Al₅O₁₂ phosphor powders were prepared using the solution combustion method. Formation and homogeneity of the Er₃Al₅O₁₂ phosphor powders have been verified by X-ray diffraction and energy-dispersive X-ray analysis respectively. The frequency up-conversion from Er₃Al₅O₁₂ phosphor powder corresponding to the ²H_9/2 → ⁴I_15/2, ²H_11/2 → ⁴I_15/2, ⁴S_3/2 → ⁴I_15/2, ⁴F_9/2 → ⁴I_15/2 and the infrared emission (IR) due to the ⁴I_13/2 → ⁴I_15/2 transitions lying at ∼410, ∼524, ∼556, 645–680 nm and at ∼1.53 μm respectively upon excitation with a Ti-Sapphire pulsed/CW laser have been reported. The mechanism responsible for the frequency up-conversion and IR emission is discussed in detail. Defect centres induced by radiation were studied using the techniques of thermoluminescence and electron spin resonance. A single glow peak at 430°C is observed and the thermoluminescence results show the presence of a defect center which decays at high temperature. Electron spin resonance studies indicate a center characterized by a g-factor equal to 2.0056 and it is observed that this center is not related to the thermoluminescence peak. A negligibly small concentration of cation and anion vacancies appears to be present in the phosphor in accordance with the earlier theoretical predictions.     

Infrared emission and defect centres in Er and Yb codoped Y3Al5O12 phosphors

YAG phosphor powders doped/codoped with Er³⁺/(Er³⁺ + Yb³⁺) have been synthesised by using the solution combustion method. The effect of direct pumping into the ⁴I_11/2 level under 980 nm excitation of doped/codoped Er³⁺/Yb³⁺−Er³⁺ in Y₃Al₅O₁₂ (YAG) phosphor responsible for an infrared (IR) emission peaking at ∼1.53 μm corresponding to the ⁴I_13/2→⁴I_15/2 transition has been studied. YAG exhibits three thermally-stimulated luminescence (TSL) peaks at around 140°C, 210°C and 445°C. Electron spin resonance (ESR) studies were carried out to identify the centres responsible for the TSL peaks. The room temperature ESR spectrum of irradiated phosphor appears to be a superposition of two distinct centres. One of the centres (centre I) with principal g-value 2.0176 is identified as O⁻ ion, while centre II with an isotropic g-factor 2.0020 is assigned to an F⁺ centre (singly ionised oxygen vacancy). An additional defect centre is observed during thermal-annealing experiments and this centre (assigned to F⁺ centre) seems to originate from an F-centre (oxygen vacancy with two electrons) and these two centres appear to correlate with the observed high-temperature TSL peak in YAG phosphor.     

Laser spectroscopy of optical centers in borosilicophosphate glass, coactivated by erbium and ytterbium ions

Based on analysis of the laser emission spectra of borosilicophosphate glass, coactivated by Er³⁺ and Yb³⁺ ions, we have determined the structure of the Stark splitting of the luminescence band for the erbium ion in the 1.5 μm region (the transition ⁴I_13/2 → ⁴I_15/2). In the wavelength interval 1532–1547 nm, we identified 12 sets of lines belonging to different types of optical centers of predominantly cubic symmetry. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 4, pp. 483–487, July–August, 2006.     

Spectroscopic Properties of Er3+/Yb3+-codoped PbO–Bi2O3–Ga2O3–GeO2 Glasses

We investigate the spectroscopic properties of the 1.5-μm emission from the ⁴I_13/2 → ⁴I_15/2 transition of Er³⁺ ions in PbO–Bi₂O₃–Ga₂O₃–GeO₂ glasses for applications in broadband fiber amplifiers. The measured emission peak locates at 1,532 nm with a full width at half-maximum of ∼45 nm. The glasses exhibit a large stimulated emission cross-section of 0.89 × 10⁻²⁰ cm² and a large product of 40.0. Infrared-to-green upconversion occurs simultaneously upon excitation of the 1.5-μm emission with a commercially available 980 nm laser diode. The green-upconversion intensity has a quadratic dependence on incident pump laser power, indicating a two-photon process. Energy transfer processes and nonradiative phonon-assisted decays could account for the population of the ²H_11/2 of Er³⁺. The results indicate the possibility towards the development of lead–bismuth–gallate–germanate based glasses as photonics devices.     

Enhancement of upconversion intensity in Er3+ doped tellurite glass in presence of Yb3+

TeO₂–PbO glasses doped/codoped with Er³⁺/Er³⁺-Yb³⁺ ions have been fabricated by melting and quenching method. Efficient frequency upconversion emissions spanning from blue to red regions corresponding to the ²H_11/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions, respectively, upon excitation with 976 nm diode laser radiation have been observed. The variations observed in the intensity of whole upconversion emission spectra due to the presence of the Yb³⁺ ions are reported and discussed in detail.     

Up-conversion emissions of Er<Superscript>3+</Superscript>-Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by the arc discharge synthesis method

The Er³⁺-Yb³⁺ codoped Al₂O₃ nanoparticles with an average particle size of about 50 nm have been synthesized by an arc discharge synthesis method. The green and red up-conversion emissions centered at about 526, 547 and 677 nm, corresponding respectively to the ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978-nm semiconductor laser diode excitation. The Annealing has evident effect on the up-conversion emissions of the samples: The red up-conversion emission is noticeable before annealing; however, the green up-conversion emission becomes predominant after annealing. The mixture of (Er,Yb)₃Al₅O₁₂ and α-(Al,Er,Yb)₂O₃ phases is more favorable for green up-conversion emissions due to an enhancement of the ESA (I) of ⁴I_11/2+a photon→⁴F_7/2 and ET (III) of ²F_5/2(Yb³⁺)+⁴I_11/2(Er³⁺)→²F_7/2(Yb³⁺)+⁴F_7/2(Er³⁺) processes. The two-photon absorption up-conversion process is involved in the green and red up-conversion emissions. The results have proved that arc discharge synthesis is a new promising preparation technology for optical materials. Supported by National Natural Science Foundation of China (Grant No. 10804015), the Scientific Research Foundation for Doctor of Liaoning Province (Grant No. 20071095), and the Educational Committee Foundation of Liaoning Province (Grant No. 2008123)     

Avidin conjugation to up-conversion phosphor NaYF4:Yb3+, Er3+ by the oxidation of the oligosaccharide chains

NaYF₄:Yb³⁺, Er³⁺ nanoparticles were successfully prepared by a polyol process using diethyleneglycol (DEG) as solvent. After being functionalized with SiO₂–NH₂ layer, these NaYF₄:Yb³⁺, Er³⁺ nanoparticles can conjugate with activated avidin molecules (activated by the oxidation of the oligosaccharide chain). The as-formed NaYF₄:Yb³⁺, Er³⁺ nanoparticles, NaYF₄:Yb³⁺, Er³⁺ nanoparticles functionalized with amino groups, avidin conjugated amino-functionalized NaYF₄:Yb³⁺, Er³⁺ nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy (AFM), Fourier transform infrared (FT-IR), UV/Vis absorption spectra, and up-conversion luminescence spectra, respectively. The biofunctionalization of the NaYF₄:Yb³⁺, Er³⁺ nanoparticles has less effect on their luminescence properties, i.e., they still show the up-conversion emission (from Er³⁺, with ⁴S_3/2 → ⁴I_15/2 at ~540 nm and ⁴F_9/2 → ⁴I_15/2 at ~653 nm), indicative of the great potential for these NaYF₄:Yb³⁺, Er³⁺ nanoparticles to be used as fluorescence probes for biological system.     

Dynamics of the Yb3+ to Er3+ energy transfer in LiNbO3

The energy transfer dynamics between Yb³⁺ and Er³⁺ ions in lithium niobate is investigated after ytterbium-pulsed excitation at 920 nm. The sensitisation of the LiNbO₃:Er³⁺ system with Yb³⁺ ions does not modify the lifetime of the ⁴I_13/2 erbium level (1.5-μm emission), whereas it induces a marked, concentration-dependent change in the lifetime of the ²F_5/2 (Yb³⁺) and ⁴S_3/2 (Er³⁺) multiplets (1060-nm and 550-nm emissions, respectively). The results are analysed by using the rate-equation formalism and cross-relaxation model for the energy transfer. Received: 15 October 1998 / Revised version: 24 November 1998 / Published online: 24 February 1999     

Localized desvitrifiation in Er<Superscript>3+</Superscript>-doped strontium barium niobate glass by laser irradiation

Localized desvitrifiation in strontium barium niobate glass doped with Er³⁺ under laser irradiation has been carried out. The samples of this study have been fabricated by the melt quenching method and doped with 5% mol of Er³⁺. A 1.5-W cw Ar laser was focused on the sample to obtain desvitrifiation of the glass. Evidence of the changes induced by the Ar laser has been observed through the analysis of the photoluminescence of the Er³⁺ ions. The transitions corresponding to ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 have been studied to analyze structure changes. Microluminescence measurements have been carried out to spatially select positions inside and outside the irradiated area. We have observed changes in the emission bands corresponding to these transitions. The emission bands from Er³⁺ ions in the irradiated zone show a resolved structure while they are broadened outside that area. These changes in the optical properties of the Er³⁺ ions indicate that the Ar-laser irradiation has produced a change in the local structure of the material. These results show that a localized desvitrifiation has been produced after the laser action and the transition from glass to glass ceramic has been completed.     

Ce3+对Er3+/Yb3+共掺TeO2-WO3-ZnO玻璃发光性能的影响

在Er³⁺/Yb³⁺共掺TeO₂-WO₃-ZnO玻璃中引入Ce³⁺，研究了Ce³⁺对Er³⁺1.5μm发射性能及其上转换发光性能的影响。结果表明，随Ce³⁺浓度的增加Er³⁺1.5μm波段的荧光强度先增强后降低，优化的Ce³⁺掺杂浓度在2.07×10²⁰/cm³左右；1.5μm波段的荧光寿命则随Ce³⁺浓度的增加有轻微降低，从3.4ms降到3.0ms，但Ce³⁺浓度的增加对1.5μm波段的荧光半高宽基本无影响；Er³⁺/Ce³⁺间的交叉弛豫Er³⁺(⁴I_11/2)+Ce³⁺(²F_5/2)→Er³⁺(⁴I_13/2)+Ce³⁺(²F_7/2)使玻璃的上转换发光强度大大降低，但在过高的Ce³⁺浓度下，Er³⁺/Ce³⁺间的另一交叉弛豫Er³⁺(⁴I_13/2)+Ce³⁺(²F_5/2)→Er³⁺(⁴I_15/2)+Ce³⁺(²F_7/2)则使Er³⁺⁴I_13/2能级粒子数减少，导致1.5μm波段荧光强度和荧光寿命降低. 关键词： 碲钨酸盐玻璃 发光性能 3+离子')" href="#">Er³⁺离子 3+离子')" href="#">Ce³⁺离子 交叉弛豫     

Diode laser pumped Gd2O3:Er3+/Yb3+ phosphor as optical nano-heater

An intense green upconversion (UC) emission (λ _exc=976 nm) followed by the heating effect in Yb³⁺/Er³⁺ co-doped Gd₂O₃ nanoparticles has been detected. A temperature rise up to 504 K has been observed (on a noteworthy low laser excitation of 290 mW) using fluorescence intensity ratio (FIR) method of the thermalized UC luminescence bands ²H_11/2→⁴I_15/2 and ⁴S_3/2→⁴I_15/2 of Er³⁺ ion. The reported controlled optical heating of nanoparticles and its nano-volume has potential applications in biomedicines and in the creation of holes in soft materials.