Dispersion Compensation in Externally Modulated Transmission System Using Chirped Fiber Grating

We present an externally modulated NTSC AM-VSB erbium-doped fiber amplifier (EDFA)-repeated system in the 1550 nm region which uses a chirped fiber grating (CFG) as a dispersion compensation device. In contrast to the conventional externally modulated fiber optical CATV systems, either with or without dispersion compensation fiber (DCF), good performances of carrier-to-noise ratio (CNR) ≥50 dB, composite second order (CSO) ≥74 dB, and composite triple beat (CTB) ≥65 dB were achieved for the full channel band after a 100-km single-mode fiber (SMF) transmission.     

Dispersion Compensation in Externally Modulated Transmission System Using Chirped Fiber Grating

We present an externally modulated NTSC AM-VSB erbium-doped fiber amplifier (EDFA)-repeated system in the 1550 nm region which uses a chirped fiber grating (CFG) as a dispersion compensation device. In contrast to the conventional externally modulated fiber optical CATV systems, either with or without dispersion compensation fiber (DCF), good performances of carrier-to-noise ratio (CNR) S 50 dB, composite second order (CSO) S 74 dB, and composite triple beat (CTB) S 65 dB were achieved for the full channel band after a 100-km single-mode fiber (SMF) transmission.     

外调制激光器输出功率高精度控制技术研究

为了研究高速1550 nm微波光纤链路的高精度外调制特性,针对多量子阱分布反馈激光器的物理模型讨论了输出功率、阈值电流与温度的依赖关系,建立了相应的恒温恒功率控制电路,使激光器输出功率稳定在±0.005 dB以内,调制输出3 dB谱宽为0.5 nm,边模平坦,边模抑制比大于30 dB。另外设计了自动增益控制电路和附加相位调制电路,对外调制阶段的光功率进行控制。实验结果表明,采用1550 nm激光器及上述控制电路构成相应的外调制微波光纤链路系统,可有效地提高光发射模块输出光功率的稳定性,克服了直接调制带来的光谱展宽和消光比不稳定的缺点,实现了微波信号的高线性低失真传输。     

大容量长距离传输用低非线性效应非零色散位移光纤

利用非等温等离子体化学气相沉积 (PCVD)工艺制备了一种适合于大容量高速率长途干线网与城域网的中芯下陷型纤芯结构非零色散位移光纤。该光纤的有效面积大于 95 μm2 ,在 15 5 0nm波段的色散值约为9ps/(nm·km) ,有效的抑制了传输过程中光非线性效应的产生。通过对光纤剖面结构的优化设计 ,光纤的 15 5 0nm处的传输损耗降到约 0 .2 1dB/km ,与传统单模光纤的熔接损耗低于 0 .11dB ,且在直径为 6 0mm圆筒上绕 10 0圈后在 14 6 0nm到 16 2 5nm波长范围所引起的附加弯曲损耗均低于 0 .0 2dB/km。同时 ,该光纤色散斜率低于0 .0 6 5 ps/(nm2 ·km) ,偏振模色散 (PMD)小于 0 .0 5 ps·km-1/2 。此外 ,由于光纤的零色散点移到了 14 30nm以下 ,使波分复用 (WDM)传输在S波段 (14 6 0～ 15 30nm)、C波段 (15 30～ 15 6 5nm)、L(15 6 5～ 16 2 5nm)波段上都兼容。     

Transmission Performance Improvement in Microwave/Millimeter-Wave Optical System Using Chirped Fiber Grating

A chirped fiber grating (CFG) written by the moving fiber/phase mask scanning beam technique with a uniform mask is used to demonstrate the dispersion compensation in the externally modulated microwave/millimeter-wave over fiber system. It is found that the use of the CFG is an efficient way to compensate for the severe RF power degradation induced by the fiber chromatic dispersion, which results in a significant improvement in the transmission performance. The signal to noise ratio is improved from 4.8 dB to 24.4 dB when 10.58 GHz RF signal carrying 5 Mbit/s QPSK format data is transmitted over 35 km single mode fiber.     

Fiber to the Classrooms: Internet over Fiber Optical CATV System

This study proposed and demonstrated a directly modulated NTSC AM-VSB 77-channel plus Internet access system using a Fabry-Perot (FP) laser diode, an optical isolator, fiber Bragg grating (FBG), wavelength-division-multiplexing (WDM), channel conversion and two-way communication techniques over an existing multimode fiber (MMF) on the author’s campus. Performances of carrier-to-noise ratio (CNR) of >43dB composite second order (CSO) of >53dB and composite triple beat (CTB) of >53dB were obtained over a 2-km MMF transmission. The proposed two-way communication system is simple and suitable for fiber to the classrooms application.     

Fabrication of low OH loss holey fibers with varying air hole sizes and their optical properties

We experimentally investigate a flexible fabrication technique for low OH and transmission losses holey fibers with a Ge-doped core and air holes in a silica cladding region. Versatile holey fibers of different size, pitch, and shape of air holes were achieved by controlling the temperature and heating time of the holey fiber preform. In addition, we suppress the OH loss of less than ∼0.323 dB/km at 1383 nm. After fabricating holey fibers, we measure their optical properties including cut-off wavelength, mode field diameter, splicing loss, dispersion, bending loss, and polarization dependent loss based on the size of air holes. The total transmission loss was measured to be ∼0.226 dB/km at 1550 nm by improving the fabrication process. After fabricating optical patch cord based on holey fibers, we measured the long-term stability of the fabricated holey fiber by using the temperature cycling technique for 24 and obtained low power fluctuation of 0.2 dB. We achieve the high quality holey fiber with a low bending loss of ∼0.04 dB/turn under a bending radius of 2.5 mm at 1550 nm. We also obtain a tunable band rejection filter with a number of bending turns.     

Monolithic integration of electroabsorption modulator and DFB laser for 10-Gb/s transmission

A strained InGaAsP-InP multiple-quantum-well DFB laser monolithically integrated with electroabsorption modulator by ultra-low-pressure (22 mbar) selective-area-growth is presented. The integrated chip exhibits superior characteristics, such as low threshold current of 19 mA, single-mode operation around 1550 nm range with side-mode suppression ratio over 40 dB, and larger than 16 dB extinction ratio when coupled into a single-mode fiber. More than 10 GHz modulation bandwidth is also achieved. After packaged in a compact module, the device successfully performs 10-Gb/s NRZ transmission experiments through 53.3 km of standard fiber with 8.7 dB dynamic extinction ratio. A receiver sensitivity of −18.9 dBm at bit-error-rate of 10⁻¹⁰ is confirmed.     

Directly Modulated 10 Gb/s Signal Transmission over 320 km of Negative Dispersion Fiber for Regional Metro Network

We demonstrate the transmission of directly modulated 10-Gb/s WDM signals over 320 km of negative dispersion fiber (dispersion:-2.5 ps/km/nm @1550 nm) without dispersion compensation. The results indicate that a regional metro WDM network could be implemented cost-effectively by using the proposed negative dispersion fiber and direct modulated lasers.     

Low Loss Polarization Maintaining Photonic Crystal Fiber

A low loss polarization maintaining photonic crystal fiber has been fabricated. The fiber loss was 1.3 dB/km at 1550 nm. The polarization crosstalk for a 100-m fiber was ?5 dB at 1550 nm.     

A Novel Fabrication for Method Long Period Fiber Grating

A new method of fabricating all-fiber broadband-rejection filter based on long period fiber grating (LPFG) is proposed. The principle in the method is to make periodic asymmetrical deformation in the core of fiber without microbends by electrode discharging so as to induce periodic refractive index changes. Two kinds of filters whose rejection peak wavelength at 1550 nm and 1310 nm are obtained. The insertion loss is less than 0.6 dB and 1.4 dB respectively. The 20 dB bandwidth ranges from 10 nm to 39 nm. The backward reflection loss is extremely small (less than -70 dB). Such devices can be used as isolation filters in 1310/1550 nm WDM system and other fields.     

A Novel Fabrication for Method Long PeriodFiber Grating

A new method of fabricating all-fiber broadband-rejection filter based on long period fiber grating (LPFG) is proposed. The principle in the method is to make periodic asymmetrical deformation in the core of fiber without microbends by electrode discharging so as to induce periodic refractive index changes. Two kinds of filters whose rejection peak wavelength at 1550 nm and 1310 nm are obtained. The insertion loss is less than 0.6 dB and 1.4 dB respectively. The 20 dB bandwidth ranges from 10 nm to 39 nm. The backward reflection loss is extremely small (less than - 70 dB). Such devices can be used as isolation filters in 1310/1550 nm WDM system and other fields.     

大功率、高效率、高消光比铒光纤多波长超荧光光源

采用改进的反射式Mach-Zehnder干涉滤波器，对双程后向结构掺铒光纤超荧光光源(DPB SFS) 分别进行光谱分割和光谱预分割，构建了两种结构的多波长超荧光光纤光源（MW SFS），波长间隔为～0.8 nm时，在1550 nm附近（1542～1559 nm）20个波长的功率波动小于0.5 dB其中前者消光比高达27 dB；后者消光比～18 dB，在泵浦光功率为72.8 mW时，最大输出功率25.3 mW，光光转换效率高达34.8%改变Mach-Zehnder干涉仪的臂长差，采用光谱预分割技术，得到1550 nm附近波长间隔～0.4 nm、消光比～16 dB的50个波长输出     

Externally-modulated high-power fiber grating ring laser for digital transmission

We have constructed a low-cost, double-cavity erbium-doped fiber ring laser with a fiber Bragg grating and a 2×2 coupler. A high output power of 8.7 dBm and a signal-to-noise-floor ratio of 43 dB were demonstrated. This fiber grating ring laser is used as the light source for the 2.488 Gb/s transmission experiment through a 100 km single mode fiber. To our knowledge, this is the first time a fiber grating ring laser is being used as an externally modulated source for digital transmission.     

Simulative investigation the impact of optical amplification techniques on single- and dual-electrode MZM and direct modulator's in single-tone RoF system

Since the introduction of erbium-doped fiber amplifier (EDFA) in optical fiber communication systems at 1550 nm, the fiber loss is no longer considered as the limiting factor but the fiber dispersion and chirp parameters play an important role in degrading the performance of optical communication systems. Further, the invention of external modulators of Mach-Zehnder (MS) type minimizes the transmission power penalty due to fiber chromatic dispersion as these modulators are consider almost chirp-free modulators. Also, better suppression of nonlinear distortions consists of harmonic distortions (HDs) and intermodulation distortions (IMDs) were achieved by using Mach-Zehnder external modulator [8]. In this work, a simulation comparison of external- and direct-modulation schemes using different optical amplifiers; SOA and EDFA in single-tone RoF system is reported. A single-tone channel of 20 GHz is transmitted over single-mode fiber (SMF) either externally modulated by using single-electrode (SEMZM) - and dual-electrode (DEMZM) - Mach-Zehnder modulator or by direct-modulation scheme. Better improvements in the measurement of received RF power of a 20 km linked single-tone RoF system are achieved by using SEMZM with EDFA, which means maximum optical link is achieved between Central Office (CO) and Base Station (BS). Further, this scheme provides better BER as compare to other schemes discussed in this paper.     

光波导-光纤耦合对接自动化系统的研究

开发设计了三种适用于光波导自动对接耦合的调芯方案：半值法、质心法、遗传法.完成了自动对接系统样机.通过了两类波导－光纤自动端面对接的实测.结果表明,该自动对接系统具有高效率低损耗对接的良好性能.     

光波导-光纤自动调芯系统研究

设计了两种适用于光波导高精度自动对接耦合的调芯方案,从原理上克服了常规调芯过程中微变信号精确测试的困难。完成了调芯系统的光机电一体化、控制程序和接口界面。单模光纤作为标准波导的端面耦合自动凋芯试验显示,平均耦合损耗分别为0．075 dB(1310nm波长)和0．062 dB(1550nm波长),相应的标准误差分别为0．0099 dB和0．0066 dB．调芯过程在2min内完成。单模光纤-单模波导-单模光纤的对接耦合实验结果表明,端面耦合损耗平均值分别为0．140 dB(1310nm波长)和0．109 dB(1550nm波长),标准误差分别为0．0082dB和0．0107dB,调芯时间累计不超过8min。     

Polycarbonate hollow-core microstructured optical fiber

A hollow-core microstructured polymer optical fiber is fabricated from polycarbonate material and guidance by inhibited coupling in a two-layer structure is demonstrated in two strong transmission bands with minimum losses of 9.0 dB/m at 800 nm and 3.1 dB/m at 1550 nm. The latter corresponds to a loss well below the polycarbonate material loss at this wavelength, and to our knowledge it is the lowest loss hollow-core polymer fiber reported to date. The short-term operational temperature limit of the fiber is shown to be 135 degrees C, significantly higher than that of conventional polymer optical fibers made of other polymers.     

Simultaneous Compensation of Dispersion and Losses using Er-Doped Double-Core Optical Fiber

The Er-doped double-core dispersion compensating fiber (EDDCF) has been fabricated using modified chemical vapor deposition (MCVD) technique. We have obtained 14 dB gain at 1550 nm (using a diode laser of 980 nm wavelength which provides 100 mW of pump power) with dispersion of about −165 ps/km nm. It is useful for the optical fiber network where amplification as well as negative dispersion is necessary. We are the first to report the experimental realization and characterization of the EDDCF.     

Analysis of dispersion compensation by chirped fiber grating in directly and externally modulated CATV systems

The dispersion compensation effect of the chirped fiber grating (CFG) is analyzed theoretically, and analytic expressions are derived for composite second-order (CSO) distortion in analog modulated sub-carrier multiplexed (AM-SCM) cable television (CATV) systems with externally and directly modulated transmitters. Simulations are given for the two kinds of modulations and for standard single mode fiber and non-zero dispersion shift fiber (NZDSF) systems. The results show that CFG could be used as a dispersion compensator in directly modulated systems, but its dispersion coefficient should be adjusted much more precisely than the externally modulated system. The requirements for the NZDSF system could be loosened much. It is proposed that directly modulated source may be used as a transmitter in CATV systems combined with tunable CFG dispersion compensator being adjusted precisely, which may be more cost-effective than externally modulation technology.