Dependence of the magnetic properties of an amorphous metal alloy on its nanoporosity

Magnetic and structural properties of an amorphous alloy based on iron are investigated. The properties and state of the alloy are changed under hydrostatic pressure of up to 1.3 GPa. An increase in the pressure leads to a linear increase in the maximum magnetic induction and a linear decrease in the remanence. Two nanopore fractions with average sizes of ～20 and 150 nm are revealed in the alloy with the use of small-angle x-ray diffraction. The application of the pressure decreases the size of nanopores and increases the average distance between their boundaries, i.e., increases the average sizes of continuity regions in the alloy. It is established that the relative change in the magnetic characteristics is linearly related to the change in the size of the continuity regions in the alloy. Upon extrapolation to zero nanoporosity, the remanence reduces to zero. The inference is made that the nanopores play a dominant role (as compared to other structural defects) in the magnetic properties of the alloy.     

The effect of manganese on the modification of non-metallic inclusions and magnetic properties of columnar alnico 5 permanent magnets

Magnetic properties of Alnico 5 alloy of columnar structure are reviewed in terms of Mn content 0.04-0.7 wt% in the alloy. It was ascertained that all magnetic properties are affected by Mn, and deteriorate proportionally to the increased content of Mn in the alloy, the greatest changes occuring in energy product and the smallest in magnetic remanence. An increased content of Mn in Alnico 5 alloy is also responsible for a higher proportion of inclusions over 5 μm in size and the transition of inclusion from a homogeneous to a heterogeneous structure, which is an aggregate of oxides and sulphides.     

Electronic properties of strain-disordered Ni<Subscript>2.16</Subscript>Mn<Subscript>0.84</Subscript>Ga alloy

The effect of ultrarapid quenching from the melt and severe plastic torsional deformation under high pressure on the crystalline structure and the electrical, optical, and magnetic properties of a Ni_2.16Mn_0.84Ga alloy was studied. The electrical properties are discussed in terms of the Mott two-band model. The peculiarities of the magnetic properties are associated with the magnetism of itinerant electrons. The optical properties correlate with the variations in the electronic spectrum upon disordering of the alloy that follow from the results of the available energy-band-structure calculations.     

石墨烯纳米网电导特性的能带机理：第一原理计算

通过第一原理电子结构计算来研究有序多孔纳米网的电导特性变化的能带机理.能带结构分析结果表明:石墨烯纳米网超晶格(3m,3n)(m和n为整数)的电子本征态在布里渊区中心点发生四重简并;碳空位孔洞规则排列形成的石墨烯纳米网具有由简并态分裂形成的宽度可调带隙,无论石墨烯的两个子晶格是否对等.在具有磁性网孔阵列的石墨烯纳米网中,反铁磁耦合使对称子晶格的反演对称性增加了一项量子限制条件,导致能带结构在K点的二重简并态分裂成带隙.通过控制网孔密度能够有效调节石墨烯纳米网的带隙宽度,为实现新一代石墨烯纳米电子器件提供了理论依据.     

Magnetic properties of spray-formed Fe–6.5%Si and Fe–6.5%Si–1.0%Al after rolling and heat treatment

The maximum silicon content in commercial Fe–Si steels is limited to about 3.5 wt%Si, since the ductility declines sharply as this maximum is exceeded, hindering the production of thin sheets by cold/hot rolling. However, the best magnetic properties are attained at about 6.5 wt%Si, a silicon content that renders magnetostriction practically null and minimizes magnetic losses. Using spray-forming, our research group has successfully produced this type of high silicon alloy in thin sheet form by carefully controlling the many variables of the process and subsequent rolling operations. In the present study, we investigated the magnetic properties and the microstructure of spray-formed Fe–6.5 wt%Si and Fe–6.5 wt%Si–1.0 wt%Al alloys after warm rolling and heat treatment. The main cause for the brittleness of Fe–6.5 wt%Si alloy has been attributed to the B2 phase long-range ordering, which leads to premature fractures. The presence of aluminum could avoid B2 formation and improve the alloy's ductility. The binary Fe–6.5 wt% Si alloy showed the best magnetic properties, which were ascribed to a recrystallized, coarse grain size (∼500 μm; and 340 μm for the Al-containing alloy). TEM analysis showed that a well-developed B2 domain structure (about 50–300 nm in size) was formed in the binary alloy when low cooling rates are prevailing after heat treatment. This structure contributed to improve additionally the magnetic properties, but its effect was not so strong as that of the grain size. The addition of Al to the binary alloy suppressed B2 formation, as indicated by Mossbauer spectroscopy, and apparently hindered excessive grain growth, which may explain the slightly poorer magnetic properties when compared with the binary alloy.     

Magnetic and electrical properties of Co-rich cobalt-iron films

The crystalline structures and galvanomagnetic properties have been studied on Co-Fe films of 80–100% Co. It is found that in single- to multiphase transition region the structure of this alloy system is characterised by the minimum electron number per atom. Moreover, the variations in such magnetic parameters as the anomalous Hall constant and saturation induction do not follow the simple mixing rule, but depend on a crystal structure type of the alloy.     

Microstructures and magnetic properties of Fe---Pt permanent magnets

We have investigated the magnetic properties of Fe---38.5Pt, Fe---39.5Pt and Fe---50.0Pt (at%) alloys after various heat treatment conditions using a vibrating sample magnetometer, and correlated these properties with the microstructures of the alloys by transmission electron microscopy. The Fe---50Pt alloy shows poor magnetic hardness regardless of the heat treatment conditions. The magnetic hardness of the Fe---39.5Pt alloy shows a maximum value after annealing for 10 h at 873 K, while it monotonically decreases after annealing at 1073 K. The alloy with the highest coercivity was composed of a single phase γ₁ with an average domain size of approximately 10 nm. The electron diffraction results indicate that the alloy is frustrated with accumulated stress, induced by a cubic → tetragonal transformation which occurs without twinning. On the other hand, when stress is relieved by twin formation after prolonged aging, the coercivity decreases. By annealing at 1073 K, the well known polytwin structure evolves. However, only poor hard magnetic properties are observed when this polytwin structure appears. Hence, the highest coercivity is attributed to the formation of nanoscale L1₀ ordered antiphase domains which is expected to be a highly anisotropic single domain magnetic particle.     

铁基软磁非晶/纳米晶合金研究进展及应用前景

非晶合金通常是将熔融的金属快速冷却、通过抑制结晶而获得的原子呈长程无序排列的金属材料.由于具有这种特殊结构,铁基软磁非晶合金具有各向同性特征、很小的结构关联尺寸和磁各向异性常数,因而具有很小的矫顽力H_c,但可和晶态材料一样具有高的饱和磁感强度B_s.优异的软磁性能促进了铁基软磁非晶合金的应用研究.目前,铁基软磁非晶/纳米晶合金带材已实现大规模工业化生产和应用,成为重要的高性能软磁材料.本文回顾了软磁非晶合金的发现和发展历程,结合成分、结构、工艺对铁基非晶/纳米晶合金软磁性能的影响,介绍了相关基础研究成果和工艺技术进步对铁基软磁非晶/纳米晶合金研发和工业化应用的重要贡献.并根据结构、性能特征将铁基软磁非晶合金研发与应用分为三个阶段,指出了目前铁基软磁非晶合金研发与应用中面临的挑战和发展方向.     

微观组织结构对铂钴永磁合金磁性能的影响

系统研究了Pt-Co合金磁性能与其微观组织结构间的关系.合金铸锭的X射线衍射结果表明：熔炼后的Pt-Co合金铸锭沿冷却方向存在明显的织构;扫描电镜照片显示合金的组织结构为柱状晶结构,柱状晶的生长方向平行于冷却方向;合金铸锭经塑性变形和再结晶处理后柱状晶组织消失,电镜照片显示处理后的合金晶粒尺寸变小且均匀;对不同组织结构的Pt-Co合金磁性能的测试结果表明,经塑性变形及再结晶处理后合金的磁性能有了明显提高,说明该合金中晶粒尺寸和取向是影响其矫顽力的重要因素. 关键词： 铂钴永磁合金 磁性能 织构     

Microstructures and magnetic properties of FePt permanent magnets

We have investigated the magnetic properties of Fe38.5Pt, Fe39.5Pt and Fe50.0Pt (at%) alloys after various heat treatment conditions using a vibrating sample magnetometer, and correlated these properties with the microstructures of the alloys by transmission electron microscopy. The Fe50Pt alloy shows poor magnetic hardness regardless of the heat treatment conditions. The magnetic hardness of the Fe39.5Pt alloy shows a maximum value after annealing for 10 h at 873 K, while it monotonically decreases after annealing at 1073 K. The alloy with the highest coercivity was composed of a single phase γ₁ with an average domain size of approximately 10 nm. The electron diffraction results indicate that the alloy is frustrated with accumulated stress, induced by a cubic → tetragonal transformation which occurs without twinning. On the other hand, when stress is relieved by twin formation after prolonged aging, the coercivity decreases. By annealing at 1073 K, the well known polytwin structure evolves. However, only poor hard magnetic properties are observed when this polytwin structure appears. Hence, the highest coercivity is attributed to the formation of nanoscale L1₀ ordered antiphase domains which is expected to be a highly anisotropic single domain magnetic particle.     

方解石纳米孔隙内二氧化碳毛细凝聚的分子模拟

在二氧化碳地质封存、增产非常规油气以及孔隙材料表征测量方面,纳米孔隙中二氧化碳相态的准确预测具有重要意义.然而,由于纳米尺度下毛细力、分离压等作用力占据主导因素,流体在孔隙中的相行为与体相流体存在根本不同.已有实验和模拟表明,Kelvin毛细凝聚理论无法预测特征尺度10 nm下的,孔隙内流体凝聚压力与体相饱和蒸气压的偏...     

Impacts of amorphous metal-based transformers on energy efficiency and environment

Magnetic properties of a recently developed Fe-based amorphous alloy with a high saturation induction of 1.65 T are reviewed. The increased saturation induction is fully utilized in transformers with reduced magnetic losses, physical sizes and audible noises, minimizing some of the drawbacks of amorphous metal-based transformers based on a currently available amorphous alloy. Impacts of this on the worldwide energy savings and reduction of greenhouse gas emissions are discussed. A recent effort in achieving a saturation induction beyond 1.65 T in nanocrystalline alloys is mentioned.     

Magnetic properties of nickel clusters in nanoporous carbon

The magnetic properties of nanoporous carbon samples whose pores were loaded by nickel are described. It is shown that a sample becomes superparamagnetic for temperatures T<T _C (Ni) only in the case where a noticeable fraction of Ni is contained in the nanopores. The nanopore size estimated from magnetic measurements coincides with the estimates derived earlier from small-angle x-ray scattering studies.     

The quenching effects of hot band annealing on grain-oriented electrical steel

The grain-oriented electrical steels are widely used in transformers, which demand low iron loss and high induction of core materials. In order to obtain good magnetic properties, a series of rolling, annealing and coating processes are carried out. Hot band annealing, which influences the ductility for cold rolling and the development of AlN inhibitors, is one of the most important processes. This study investigated the phases and different kinds of precipitations in microstructures of annealed hot band by means of the optical and electronic microscopies. On the other hand, a Themo-Calc software and the solubility product equations of AlN are used to calculate the phase diagram of Fe-Si-C alloy and the amount of AlN at high temperature. Microstructures including ferrite, cementite, pearlite and martensite were observed. The size and shape of precipitates, i.e. GP Zone, TiN, AlN, MnS, oxide and carbide, were identified. The relationship between the amount of nano-scale AlN and magnetic properties indicated that the suitable cooling method resulted in lower iron loss and higher magnetic induction. The result could help to realize the following microstructure evolution and mechanism of inhibitors in grain-oriented electrical steel.     

Microstructure and magnetic properties of Fe72.5Cu1M2V2Si13.5B9 (M=Nb, Mo, (NbMo), (MoW)) nanocrystalline alloys

The microstructure and magnetic properties of Finemet-type Fe_72.5Cu₁M₂V₂Si_13.5B₉ (M=Nb, Mo, (NbMo), (MoW)) alloys have been systematically studied. Results show that the nanocrystalline alloy with M=NbMo has the smallest grain size of about 8 nm. The order of the effect of Nb, Mo and W additions in decreasing the α-Fe grain size in nanocrystalline alloys is Nb>Mo>W. The best DC soft magnetic properties are obtained in the alloy with M=Nb. In the case of AC soft magnetic properties, the Nb alloy also exhibits a very low core loss comparing with typical Finemet alloy. Therefore, the Nb alloy is suitable for use as a transformer core material. In addition, it is shown that a narrow grain size distribution and a uniform dispersion of α-Fe grains in the amorphous matrix are very crucial for the development of new Finemet-type nanocrystalline alloys with good soft magnetic properties.     

Synthesis of nanoporous structures in metallic materials under laser action

We defined conditions of the laser-aided formation of nanoporous structures with nanopores ranging in size from 40 to 50 nm using laser pulses of 10.6 μm wavelength at a pulse-repetition rate of up to (4-5)×10³ Hz for a model metallic material (a two-component alloy “brass of 62%”). It has been established that the exposure to a uniform laser light at depths of up to 25-30 μm results in the formation of nanopores with a relatively uniform distribution across the surface. The resulting pattern contains both solitary pores and ramified porous channels. The nanopores are uniformly distributed within a subgrain, being fairly stable in size and shape. The nanopore size and shape feature larger non-uniformity on the subgrain boundary. The resulting metallic structures show promise for use as catalysts and ultrafiltration membranes.     

Co50Fe50-xSix合金的结构相变和磁性

利用实验测量和理论计算相结合的方法,研究了介于B2结构CoFe低有序合金和L21结构Co2FeSi高有序合金之间的Co50Fe50-xSix合金的结构相变、磁相变、分子磁矩和居里温度.采用考虑Coulomb相互作用的广义梯度近似（GGA＋U）方法计算了合金的能带结构.研究发现,合金出现较强的原子有序倾向,表现出较强的共价成相作用.合金的晶格常数、磁矩、居里温度随Si含量的增加而线性地降低,极限成分Co2FeSi合金的分子磁矩和居里温度分别达到5.92μB和777℃.原子尺寸效应导致合金晶格发生变化,但并未成为居里温度和分子磁矩变化的主导因素.分子磁矩的变化符合Slater-Pauling原理,但发现原子磁矩的变化并非线性,据此提出了共价成相对磁性影响的观点.采用Stearns理论解释了居里温度的变化趋势,排除了原子间距对居里温度的主导影响作用.能带计算的结果还表明,Co2FeSi作为半金属材料并非十分完美,可能在实际应用中会出现自旋极化率降低的问题.发现该系列合金的结构相变和磁相变随着成分的变化聚集在窄小的成分和温度范围内.     

Effect of plastic deformation on the electronic properties of the Cu<Subscript>60</Subscript>Pd<Subscript>40</Subscript> alloy

The effect of severe plastic deformation by torsion under Bridgman anvil pressure (SPDT) on the electrical, magnetic, and optical properties of the Cu₆₀Pd₄₀ alloy was studied. It is shown that, after the alloy is disordered, the Curie-Weiss constants of the paramagnetic component are changed insignificantly. In this case, the temperature-independent negative component of the magnetic susceptibility decreases more than fivefold. The electrical resistance and negative thermopower, on the contrary, increase severalfold as a result of SPDT. The character of the optical conductivity is discussed using the band structure calculation results.     

Effect of a constant magnetic field on the structure and physical-mechanical properties of Cu<Subscript>57</Subscript>Be<Subscript>43</Subscript> alloy

The work presents data on the microhardness, average grain size, lattice parameters, and phase composition of Cu₅₇Be₄₃ metal alloy, annealed at a temperature of ~350°С for 1 h in a constant magnetic field with the intensity ranging from 80.0 to 557.0 kA/m. The main observed regularities of changes in the structure and properties of the material during annealing in a constant magnetic field and without it are formulated.     

A binder- and carbon-free hydrogen evolution electro-catalyst in alkaline media based on nitrogen-doped Ni(OH)2 nanobelts/3D Ni foam

Journal of Nanoparticle Research - The ground-state magnetic properties of ConPtm binary alloy clusters of size N = n + m ≤?9 are studied systematically as a function of size,...