利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

短腔Er/Yb光纤光栅激光器

报道采用光敏Ｅｒ／Ｙｂ 光纤制作短腔Ｅｒ／Ｙｂ 光纤光栅激光器的实验结果。激光谐振腔由一对直接写在３０ ｍ ｍ 长的Ｅｒ／Ｙｂ 光纤上、长度分别为６ ｍ ｍ 及１０ ｍ ｍ 、反射率分别为９０％ 及９８．６％ 、３ ｄＢ带宽分别为０．２８ ｎｍ 及０．２６ ｎｍ 的光纤布拉格光栅组成, 激光器的泵浦阈值为８ｍ Ｗ, 斜效率约１４％ , 输出光的信噪比为６１ ｄＢ, 偏振模抑制比为３０ ｄＢ。     

1.5μm波导声光可调滤光器研究

对１．５μｍ波导型声光ＴＥ－ＴＭ模式转换光滤波器进行了研究。采用了可降低驱动功率的表面声波导结构。在１．５￣１．６μｍ波段实现了可调滤光，通带宽度小于２ｎｍ，达到９７￥以上转换率所需的射频驱动功率约８０ｍＷ（１９ｄＢｍ），器件总插入损耗约９ｄＢ。     

一种增益平坦的光子晶体拉曼光纤放大器

为解决传统拉曼放大器增益系数低和增益不平坦的问题,采用级联光子晶体光纤的设计方法设计了一种增益平坦的拉曼光纤放大器.采用受激拉曼散射效应的稳态分析理论,分析了光子晶体光纤的拉曼增益谱,建立了拉曼放大器的理论模型.通过解耦合方程,推导了实现增益平坦的约束条件,发现光纤长度和泵浦功率是影响拉曼光纤放大器增益平坦度的两个参数.仿真结果表明,在1 508～1 544 nm的带宽范围内,实现了一个增益高达21 dB,增益平坦度仅为0.14 dB的光子晶体拉曼光纤放大器,可在光纤通信系统应用中发挥重要作用.     

双尾纤式多功能光隔离器研究

提出并成功研制了一种具有功能复用的新型的多功能光隔离器结构, 对其进行了传输特性性能理论分析, 分析表明, 该器件具有与单尾纤光隔离器相同的低插入损耗, 高隔离度等特性, 实验结果显示,所设计的1550 nm双通道多功能光隔离器插入损耗分别为0.28 dB和0.11 dB, 隔离度分别为55 dB和54 dB, 达到了隔离器需要满足的标准, 性能良好, 同时具有成倍降低器件制造成本的效用.     

双波长啁啾相移光纤光栅

理论研究并实验验证了一种含有两段π相移的啁啾相移光纤光栅.采用F矩阵对啁啾相移光纤光栅进行计算并分析了该光栅的谱特性.含有两段π相移的啁啾相移光纤光栅可以在普通啁啾光栅透射谱阻带中产生双波长透射峰,透射峰位置直接取决于光栅中π相移的位置,透射峰的线宽和透射峰的波长间隔没有关系,仅随着啁啾率的增大而增大.采用带相位掩模的逐点扫描法对含有两段π相移的双波长啁啾相移光栅进行了制作,获得波长间隔为8 nm的双波长透射谱的光栅器件.该光栅的消光比和3 dB谱线宽分别为20 dB和0.08 nm,实验结果和理论设计一致.     

用于液压传感的双芯光子晶体光纤

采用全矢量有限元方法进行光纤设计优化,得到横截面上失去两层空气洞的双芯光子晶体光纤,可用于液压传感.优化的双芯光子晶体光纤的模场半径和数值孔径与单模光纤基本一致,在优化的双芯光子晶体光纤和单模光纤之间有一个相对较低的熔接损耗.计算结果表明由模场半径和数值孔径导致的不匹配造成的总共损耗可低至0.026 dB,低于传统光子晶体光纤和单模光纤0.1 dB的直接熔接损耗.对基于20 cm双芯光子晶体光纤的液压传感器的性能进行研究,结果表明在0～500 MPa量程内的灵敏度为-1.6 pm/MPa.     

基于高双折射光纤布拉格光栅的自动增益控制掺铒光纤放大器

掺铒光纤非均匀展宽引起的空间烧孔现象导致单波长激光并不能完全控制放大器增益,提出了一种新颖的自动增益控制掺铒光纤放大器的结构:即采用高双折射光纤布拉格光栅产生抽运光,其写制光栅的波峰对应的波长分别为1549.3 nm和1549.83 nm,波长间隔为0.53 nm。通过调整偏振控制器,就实现了单激光或双激光的增益控制。这种设计增益控制范围为40 nm(1530~1570 nm),当输入功率在-40~-15 dBm的动态范围内,双激光增益控制的掺铒光纤放大器的平均增益和噪声系数分别约为22.22 dB和8.69 dB,而它们的漂移分别被钳制在0.69 dB和1.51 dB。系统性能测试表明:双激光控制掺饵光纤放大器在稳定性方面比单激光有着明显的优势。     

新型光纤光栅水声传感器的研究

提出了一种新型的光纤布拉格光栅(FBG)水声传感探头结构以及光纤光栅传感信号的自解调方法。利用一对匹配光栅构成推挽结构,实现了传感-解调的合二为一,大大地减小了系统的复杂度;并通过筒状弹性体结构,解决了裸光纤光栅测量水声信号的灵敏度过小的问题,并具有温度补偿作用。仿真与初步实验结果表明,该水听器探头的测量动态范围超过100 dB,在100~200 dB re 1μPa的水声压范围内,测量灵敏度为0.36 nm/Mpa。     

基于环形芯光纤的超低差分模式增益涡旋光纤放大器

提出了一种基于环形芯铒离子部分掺杂光纤的涡旋光纤放大器。针对该掺铒光纤的放大特性,研究了光纤长度、掺铒浓度与抽运功率对信号模式增益特性的影响。研究结果表明,该光纤放大器能够支持22个轨道角动量模式稳定传输,且C波段(1530~1565 nm)所有信号模式增益大于23 dB,信噪比高于27 dB,差分模式增益小于0.015 dB。所提出的基于环形芯光纤的涡旋光纤放大器具有支持轨道角动量模式数量多、差分模式增益低、信噪比高的优势,对于OAM复用长距离传输系统中的在线放大具有重要参考价值。     

基于长周期光纤光栅滤波器的掺铒光纤放大器理论和实验研究

从理论和实验上研究了带有高频二氧化碳激光写入的低成本长周期光纤光栅（LPFG）掺铒光纤放大器（EDFA）.结果表明,单波长和多波长EDFA的性能都可以通过在掺铒光纤（EDF）中插入长周期光纤光栅用作自发辐射噪声（ASE）滤波器或增益平坦器来提高性能.优化设计了带LPFG噪声滤波器的线放EDFA,与没有LPFG噪声滤波器相比,线放的噪声和小信号增益分别被减小和提高了约0.5 dB和7 dB。通过在多波长EDFA的EDF中插入一个LPFG增益平坦滤波器的方法,获得了1.5 dB的增益平坦度,与没有LPFG平坦器相比,EDFA的噪声被减小了0.1 dB,增益被提高了1 dB.     

Fiber to the Classrooms: Internet over Fiber Optical CATV System

This study proposed and demonstrated a directly modulated NTSC AM-VSB 77-channel plus Internet access system using a Fabry-Perot (FP) laser diode, an optical isolator, fiber Bragg grating (FBG), wavelength-division-multiplexing (WDM), channel conversion and two-way communication techniques over an existing multimode fiber (MMF) on the author’s campus. Performances of carrier-to-noise ratio (CNR) of >43dB composite second order (CSO) of >53dB and composite triple beat (CTB) of >53dB were obtained over a 2-km MMF transmission. The proposed two-way communication system is simple and suitable for fiber to the classrooms application.     

Grating-Outcoupled Radiation in Second-Order Fiber Bragg Gratings

Abstract

The experimental results of the radiation for second-order fiber Bragg gratings, which are made of a single-mode photosensitive fiber (PS-1500; Fiber-Core Corp.) and a single-mode fiber (SMF-28; Corning Inc.), by a phase mask writing fabrication technique are explored. For PS-1500 fiber Bragg gratings, the maximum radiation efficiency of ?23.5 dB at resonance λ = 1,539.34 nm with a very narrow bandwidth (about 0.02 nm) are measured from a 10-mm-diameter photo-detector, while for SMF-28 fiber Bragg gratings, the maximum radiation efficiency is ?34.6 dB (λ = 1,538.03 nm) with a bandwidth of 0.06 nm. The total efficiencies of the radiation are about ?16.8 dB for PS-1500 fiber Bragg gratings and ?28.1 dB for SMF-28 fiber Bragg gratings.     

Low Loss Polarization Maintaining Photonic Crystal Fiber

A low loss polarization maintaining photonic crystal fiber has been fabricated. The fiber loss was 1.3 dB/km at 1550 nm. The polarization crosstalk for a 100-m fiber was ?5 dB at 1550 nm.     

Raman-Assisted Passively Mode-Locked Fiber Laser

We propose and demonstrate a Raman-assisted passively mode-locked Yb-doped fiber laser in a normal dispersion regime. A section of highly nonlinear fiber is adopted to enhance the nonlinearity to extend the bandwidth of the gain spectrum by the stimulated Raman effect. The mode-locked fiber laser emits a broad spectral bandwidth of 64 nm at the-20 dB level and a highly stable pulse operation with a signal-to-noise ratio of 77 dB.     

倒锥透镜型塑料光纤连接器光学特性研究

提出一种基于倒锥透镜光纤端的新型塑料光纤连接器.为了增大光纤的数值孔径,降低光纤端面对于对准准确度的要求,连接器的光纤连接端面制成倒锥透镜形状.利用截断法对该类型连接器的光学特性进行了测试.1 m长光纤跳线总损耗有75.7％集中在5.4 dB～6.0 dB之间,连接损耗70.7%集中在2.1 dB~2.7 dB之间,同一组跳线插拔200次连接损耗有95％集中分布在2.2 dB～2.58 dB.实验结果表明：倒锥透镜型塑料光纤连接器可以满足“光纤入户”对连接器性能的要求.     

Fiber devices using polarization- maintaining fibers

Fiber devices using polarization-maintaining fibers called PANDA fibers are presented. They are polarization-maintaining couplers and polarization-splitting couplers, optical isolators and optical circulators, and multi/demultiplexers designed for 1.3 μm wavelength. Crosstalk of-32 dB and excess loss of 0.03 dB for the polarization-maintaining coupler, and polarization-splitting ratio of 17 dB and excess loss of 0.5 dB for the polarization-splitting coupler have been fabricated by a fusion-elongation method. A fiber polarizer with the extinction ratio of more than 40 dB has been presented by using the difference of bending loss between the orthogonal modes in the PANDA fibers. Multi/demultiplexer with narrow band-pass of 1.4 nm utilizing combination of PANDA fiber polarization dispersion and the polarization-splitting coupler has been realized. An optical isolator consisting of fiber polarizers and a spherical YIG with a lens function and an optical circulator consisting of polarizing-splitting couplers and spherical YIGs have been achieved.     

A High Power Conversion Efficiency L-Band Erbium Doped Fiber Amplifier

By using two sections of erbium doped fiber and a fiber optical reflector, a novel, highly efficient L bandamplifier is demonstrated with significantly power-conversion-efficiency enhancement and the gain increasing of as much as 13 dB.     

混合泵浦两段级联掺铒光纤放大器实验研究

基于内插隔离－耦合环两段级联新结构，采用９８０ｎｍ与１４８０ｎｍ激光二极管混合泵浦方式，研制出在１．５５μｍ波段兼具高增益，大功率，低噪声九特性的掺铒光纤放大器。     

Fiber devices using polarization- maintaining fibers

Fiber devices using polarization-maintaining fibers called PANDA fibers are presented. They are polarization-maintaining couplers and polarization-splitting couplers, optical isolators and optical circulators, and multi/demultiplexers designed for 1.3 μm wavelength. Crosstalk of-32 dB and excess loss of 0.03 dB for the polarization-maintaining coupler, and polarization-splitting ratio of 17 dB and excess loss of 0.5 dB for the polarization-splitting coupler have been fabricated by a fusion-elongation method. A fiber polarizer with the extinction ratio of more than 40 dB has been presented by using the difference of bending loss between the orthogonal modes in the PANDA fibers. Multi/demultiplexer with narrow band-pass of 1.4 nm utilizing combination of PANDA fiber polarization dispersion and the polarization-splitting coupler has been realized. An optical isolator consisting of fiber polarizers and a spherical YIG with a lens function and an optical circulator consisting of polarizing-splitting couplers and spherical YIGs have been achieved.