Optical properties of TiO2 anatase - Carbon nanotubes composites studied by cathodoluminescence spectroscopy

Luminescence spectra obtained by electron bombardment (cathodoluminescence, CL) on TiO₂ (anatase)/carbon nanotubes (CNT) composite, show only one visible band at 498 nm, while the spectra taken from pure anatase samples show two bands at 498 and 545 nm. We demonstrate that the visible luminescence bands are originated by TiO₂ surface defects due to oxygen vacancies, and that this luminescence signal is independent of TiO₂ mineral form (anatase or rutile). Moreover we obtain that the 545 nm band quenching in TiO₂/CNT composites is caused by empty oxygen vacancies (OV) related to oxygen given from oxygen-rich pristine powder of carbon nanotubes. Our conclusions are also supported by X-ray photoelectron spectroscopy (XPS), SEM analysis and energy dispersed X-ray measurements (EDX). Furthermore we can confirm that the NIR TiO₂ luminescence emission is linked only to the presence of Ti rutile form as described in several works in literature.     

Optical and structural properties of Eu-diffused and doped ZnO nanowires

Single crystal ZnO nanowires diffused with europium (Eu) from a solid source at 900 °C for 1 h or doped with Eu during growth have been characterized. The ZnO nanowires were grown by chemical vapor deposition on Si substrates employing Au as a catalyst. The diameter of the resulting nanowires was 200 nm with a length of 1 μm. Photoluminescence spectra excited by a He–Cd laser at room temperature showed the green luminescence at 515 nm in Eu-diffused nanowires. A small red shift of near-band-edge emission of ZnO nanowires was observed in the diffused wires, but sharp emission from Eu³ ions was not present. Transmission electron microscopy shows crystalline Eu₂O₃ formation on the diffused nanowire surface, which forms a coaxial heterostructure system. When Eu was incorporated during the nanowire growth, the sharp ⁵D_O–⁷F₂ transition of the Eu³⁺ ion at around 615 nm was observed.     

Synthesis of multi-walled carbon nanotubes for NH3 gas detection

It has been recently demonstrated that carbon nanotubes (CNTs) represent a new type of chemical sensor capable of detecting a small concentration of molecules such as CO, NO₂, NH₃.In this work, CNTs were synthesized by chemical vapor deposition (CVD) on the SiO₂/Si substrate by decomposition of acetylene (C₂H₂) on sputtered Ni catalyst nanoparticles. Their structural properties are studied by atomic force microscopy, high-resolution scanning electron microscopy (HRSEM) and Raman spectroscopy. The CNTs grown at 700 °C exhibit a low dispersion in size, are about 1 μm long and their average diameter varies in the range 25–60 nm as a function of the deposition time. We have shown that their diameter can be reduced either by annealing in oxygen environment or by growing at lower temperature (less than 600 °C).We developed a test device with interdigital Pt electrodes on an Al₂O₃ substrate in order to evaluate the CNTs-based gas sensor capabilities. We performed room temperature current–voltage measurements for various gas concentrations. The CNT films are found to exhibit a fast response and a high sensitivity to NH₃ gas.     

Synthesis, characterization and optical spectroscopy of Eu doped titanate nanotubes

The synthesis of Eu³⁺ doped titania nanotubes was carried out via a hydrothermal method. X-ray diffraction and transmission electron microscope analyses showed that the nanotubes were formed by rolling multilayered titania structure with a length of up to 100 nm. The Eu³⁺-doped nanotubes exhibited strong emission lines associated with the ⁵D₀→⁷F_J (with J from 1 to 4) transition of Eu³⁺ and the differences between the luminescence properties of the precursor powders and the nanotubes were studied at low temperature.     

Synthesis, luminescence and crystallographic structure of Eu-doped garnet-type yafsoanite Ca3Te2(ZnO4)3

A red-emitting phosphor of Eu³⁺-doped calcium–tellurium–zinc oxide, Ca₃Te₂(ZnO₄)₃, with a garnet-type structure was synthesized by high temperature solid-state reactions. This phosphor exhibited a strong red emission. The photoluminescence excitation spectrum showed that Ca₃Te₂(ZnO₄)₃:Eu³⁺ can be effectively excited by UV–visible light. The property of long-wavelength excitation for this material has a benefit as a red phosphor in application of white light-emitting diodes. The colour coordinates were calculated. The excitation and emission spectra and luminescence decay curves were obtained using a pulsed, tunable, narrowband dye laser. Crystallographic sites and charge compensation mechanism of Eu³⁺ ions were discussed. The emission line from Eu³⁺ in intrinsic crystallographic site in the lattice was located at 579.56 nm. The emission line from Eu³⁺ in another disturbed site, which is created by the defects created by the charge-compensation, was located at 580.88 nm. The disordered crystallographic sites of Eu³⁺ are benefit for their strong red luminescence corresponding to the ⁵D₀→⁷F₂ transition.     

Studies on structural defects in carbon nanotubes

Structural defects in carbon nanotubes (CNTs) have been paid much attention, because they influence the properties of the CNTs to some extent. Among various defects in CNTs, both single vacancies and Stone-Wales (SW) defects are the simple and common ones. In this paper, we review the progress of research in these two kinds of defects in CNTs. For single vacancies, we first address their different structural features in both zigzag and armchair CNTs, and their stabilities in CNTs with different sizes and different symmetries systematically. The presence of the single vacancies in CNTs not only influences the electronic structures of the systems, but also affects the vibrational properties of the tubes. Nevertheless, being active chemically, the single vacancies in the tubes prefer to interact with adsorbates nearby, of which the interaction of the defects with hydrogen atom, hydrogen molecule and some small hydrocarbon radicals (-CH, -CH₂ and -CH₃) are discussed. The former is associated with H storage and the latter is of merit to improve the local structure of the defect in a CNT. For the Stone-Wales defect, we mainly focus on its stability in various CNTs. The influence of the SW defects on the conductance of CNTs and the identification of such a defect in CNT is described in brief.      

Remarkably enhanced photocatalytic activity by sulfur-doped titanium dioxide in nanohybrids with carbon nanotubes

TiO₂ doped S nanohybrids with carbon nanotubes (CNTs) were synthesized with CNTs, thiourea and TiO₂ nanoparticles. The result indicated that the TiO₂ nanoparticles with about 8 nm in size are attached on the sidewall of CNTs. The nanohybrids material can absorb at longer wavelength and the absorption even covers the whole range of visible region than that only TiO₂ nanoparticles. Application of the catalysts to photocatalytic degradation of methylene blue (MB) was tested under visible light irradiation. The result suggests that a high MB degradation activity of S-TiO₂/CNTs due to a reduce band gap of TiO₂ when S is doped, and the decrease in the possibility of electron–hole recombination by CNTs. In addition, the density functional-theory (DFT) calculations of the electronic band structures and density of states (DOS) to understand the bonding states between TiO₂ and CNTs, proved that the TiO₂/CNTs system is stable.     

微量水对碳纳米管形貌的影响及其机理研究

利用介质阻挡放电等离子体化学气相沉积技术,在蒸镀有25nm Ni催化剂层的Si基片上,以CH₄和H₂作为反应气体,在973K下制备了碳纳米管,并研究了微量水的引入对碳纳米管形貌的影响.场发射扫描电子显微镜结果表明,不加水时,制备出的碳纳米管直径不均匀,分布在40—90nm之间,呈链节状的结构;加入少量水时,制备出的碳纳米管直径比较均匀,集中在70nm左右,表面为瘤状结构;当水的流量进一步增加时,得到的碳纳米管表面光滑,出现了枝状结构.原位测量了加水前后等离子体区的发射光谱,分析了微量水的引入对于碳纳米管形貌变化的影响机理. 关键词： 碳纳米管 介质阻挡放电 水 发射光谱     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 nanotubes

A series of Nd-TiO₂ powders have been prepared by the sol-gel technique with neodymium nitrate and tetra-n-butyl titanium as raw materials, and then Nd-TiO₂ nanotubes were fabricated by the hydrothermal method with a 10 mol l⁻¹ NaOH solution. The as-prepared Nd-TiO₂ nanotubes were characterized by TEM, XRD, DRS, and XPS, and their photocatalytic activity was also tested in the case of the degradation of methyl orange in water. TEM photograph showed that Nd-TiO₂ nanotubes were about 10-20 nm in diameter, with the lengths range from 100 to 300 nm. TiO₂ nanotubes contained anatase and rutile crystallites. However, 0.3% Nd-TiO₂ nanotubes contained anatase crystallites, and only little rutile crystallites, so it is shown that neodymium doping hindered the phase transformation from anatase into rutile. Nd doping increased the visible-light absorption ability of Nd-TiO₂ nanotubes, and a red shift for Nd-TiO₂ nanotubes appeared when compared to TiO₂ nanotubes. XPS analysis showed that two types of oxygen existed on the photocatalyst surface, including metal-O and hydroxyl group, and more hydroxyl group was on the surface of 2% Nd-TiO₂ nanotubes than on the surface of TiO₂ nanotubes. Nd doping enhanced the photocatalytic activities of Nd-TiO₂ nanotubes, and 0.3% Nd-TiO₂ nanotubes exhibited the highest photocatalytic activity.     

Study of the visible-excitation luminescence of NTA-TiO2(AB) with single-electron-trapped oxygen vacancies

A new kind of TiO₂ (NTA-TiO₂(AB)) with single-electron-trapped oxygen vacancies was prepared by the dehydration of nanotubed titanic acid under vacuum. Under visible-light excitation (λ_ex=420 nm to 650 nm) NTA-TiO₂(AB) showed a relatively intense emission, which red shifts with the increase of excitation wavelength. Analyzing the photoluminescence spectra, a sub-band induced by single-electron-trapped oxygen vacancies within E_g(NTA-TiO₂(AB)) was obtained. PACS 71.20.-b     

Structural,photoluminescent, and dielectric properties of Eu3+-doped Ba0.7Sr0.3TiO3 thin films

Eu³⁺-doped Ba_0.7Sr_0.3TiO₃ thin films were prepared by a chemical solution deposition method and characterized by X-ray diffraction, field emission scanning electron microscopy, photoluminescence and dielectric measurements. The thin films were well crystallized with a pure perovskite structure. A contraction of the unit cell was observed upon incorporation of Eu³⁺ ions below 2 mol%, while an expansion occurred as the Eu³⁺ concentration was further increased above 2 mol%, indicating that Eu³⁺ ions with different concentrations occupied different lattice sites. Photoluminescence spectra showed two prominent transitions of Eu³⁺ ions at 594 nm (⁵D₀ → ⁷F₁) and 618 nm (⁵D₀ → ⁷F₂) upon excitation at 395 nm (⁷F₀ → ⁵L₆). There existed two quenching concentrations at 2 mol% and 4 mol% due to different lattice sites of the Eu³⁺ ions. We also investigated the dielectric properties of the thin films. Our study suggests that Eu³⁺-doped Ba_0.7Sr_0.3TiO₃ thin films have potential applications in multifunctional optoelectronic devices.     

Short time synthesis of high quality carbon nanotubes with high rates by CVD of methane on continuously emerged iron nanoparticles

We report the variation of yield and quality of carbon nanotubes (CNTs) grown by chemical vapor deposition (CVD) of methane on iron oxide-MgO at 900-1000 °C for 1-60 min. The catalyst was prepared by impregnation of MgO powder with iron nitrate, dried, and calcined at 300 °C. As calcined and unreduced catalyst in quartz reactor was brought to the synthesis temperature in helium flow in a few minutes, and then the flow was switched to methane. The iron oxide was reduced to iron nanoparticles in methane, while the CNTs were growing.TEM micrographs, in accordance with Raman RBM peaks, indicate the formation of mostly single wall carbon nanotubes of about 1.0 nm size. High quality CNTs with I_G/I_D Raman peak ratio of 14.5 are formed in the first minute of CNTs synthesis with the highest rate. Both the rate and quality of CNTs degrades with increasing CNTs synthesis time. Also CNTs quality sharply declines with temperature in the range of 900-1000 °C, while the CNTs yield passes through a maximum at 950 °C. About the same CNTs lengths are formed for the whole range of the synthesis times. A model of continuous emergence of iron nanoparticle seeds for CNTs synthesis may explain the data. The data can also provide information for continuous production of CNTs in a fluidized bed reactor.     

Spectral structure of barium–phosphate–silicate phosphor Ba10(PO4)4(SiO4)2:EuM+

The new apatite–silicate phosphor doped with Eu ions in Ba₁₀(PO₄)₄(SiO₄)₂ matrix was synthesized through solid-state reaction. It was found that the as-synthesized phosphor displayed apparent mixture of band and line emission peaks giving rise to pseudo white light. The narrow emission bands peaking at 410 nm can be assigned to the 4f⁶5d→4f⁷(⁸S_7/2) transition of Eu²⁺ ions, and the other band at 507 nm is ascribed to anomalous fluorescent emission. One group of line emission peaking at 595 nm and 613 m were due to the ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transition of Eu³⁺ ions. The occurrence of photostimulated luminescence and discrete emission lines in violet (410 nm), green (507 nm) and red (595 nm and 613 nm) colors indicate that this material has potential application in fields of white-light-emitting.     

Sonochemical growth of antimony sulfoiodide in multiwalled carbon nanotube

This paper presents for the first time the nanocrystalline, semiconducting ferroelectrics antimony sulfoiodide (SbSI) grown in multiwalled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, S and I in the presence of methanol under ultrasonic irradiation (35 kHz, 2.6 W/cm²) at 323 K for 3 h. The CNTs filled with SbSI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect forbidden energy band gap E_gIf = 1.871(1) eV.     

Purification of carbon nanotubes grown by thermal CVD

We show the results of a set of purifications on carbon nanotubes (CNT) by acid and basic treatments. CNTs were obtained by thermal decomposition of camphor at 850 °C in a CVD growth system, by means of a growth process catalyzed by iron clusters originating from the addition of ferrocene in the precursors mixture. The purification procedures involved HNO₃, H₂SO₄, HSO₃Cl and NaOH for different process temperatures.As-grown CNTs showed a consistent presence of metal catalyst (about 6 wt%), evidenced by TGA. The purification treatments led to a certain amount of opening of the CNT tips, with a consequent loss of metal catalyst encapsulated in tips. This is also confirmed by BET analysis, which showed an increase of the surface area density of CNT after the purification.FT-IR and XPS revealed the presence of carboxylic groups on the CNT surface chemically modified by the harsh environment of the purification process.Among the various treatments that have been tested, the 1:3 solution of nitric and sulphuric acid was the most effective in modifying the CNT surface and inducing the formation of functional groups.     

On the Luminescence of Ce<Superscript>3+</Superscript>, Eu<Superscript>3+</Superscript>, and Tb<Superscript>3+</Superscript> in Novel Borate LiSr<Subscript>4</Subscript>(BO<Subscript>3</Subscript>)<Subscript>3</Subscript>

This paper reports on the photoluminescence (PL) and time-resolved properties of Ce³⁺, Eu³⁺, and Tb³⁺ in novel LiSr₄(BO₃)₃ powder phosphors. Ce³⁺ shows an emission band peaking at 420 nm under 350-nm UV excitation. Energy transfer from Ce³⁺ to Mn²⁺ takes place in the co-doped samples. Eu³⁺ shows red emission under near UV excitation. LiSr₄(BO₃)₃:Eu³⁺ phosphor could be a suitable candidate for phosphor-converted solid state lighting. The luminescence lifetime is 2.13 ms for Eu³⁺ in LiSr₄(BO₃)₃:0.001Eu³⁺. As Eu³⁺ concentration increasing, the decay curves deviate from exponential behavior. Tb³⁺ shows the strongest ⁵D₄→⁷ F₅ emission line at 540 nm. Decay curves of ⁵D₄→⁷ F₅ and ⁵D₃→⁷ F₅ emission with different Tb³⁺ concentrations were also measured. Cross-relaxation process is discussed based on the decay curves.     

Synthesis of carbon nanotubes via Fe-catalyzed pyrolysis of phenolic resin

Carbon nanotubes (CNTs) with 40–100 nm in diameter and tens of micrometers in length were prepared via catalytic pyrolysis of phenol resin in Ar at 673–1273 K using ferric nitrate as a catalyst precursor. Structure and morphology of pyrolyzed resin were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. Ferric nitrate was transformed to Fe₃O₄ at 673 K, and to metallic Fe and Fe_xC carbide at 873–1273 K. The optimal weight ratio of Fe catalyst to phenol resin for growing CNTs was 1.00 wt%, and the optimal temperature was 1073 K. In addition, use of a high pressure increased the yield of CNTs. Density functional theory (DFT) calculations suggest that Fe catalysts facilitate the CNTs growth by increasing the bond length and weakening the bond strength in C₂H₄ via donating electrons to the C atoms in it.     

A potential red-emitting phosphor with high color-purity for near-UV light emitting diodes

New red tungstates phosphors, Na₅La_1?xLn_x(WO₄)₄ (Ln = Eu, Sm) and Na₅Eu_1?xSm_x(WO₄)₄, were prepared by solid-state reaction technique. And their structure and photo-luminescent properties were investigated. The introduction of Sm³⁺ broadened the excitation band around 400 nm of the phosphors, and strengthened the red emission. And the possible energy transfer process from Sm³⁺ to Eu³⁺ is discussed. The single red LED was fabricated by combining InGaN chip with Na₅Eu_0.94Sm_0.06(WO₄)₄ as red phosphor, intense red light can be observed by naked eyes. Then the phosphor Na₅Eu_0.94Sm_0.06(WO₄)₄ may be a good candidate for red component of near-UV InGaN-based W-LEDs, because of efficient red-emitting with broadened absorption around 400 nm and appropriate CIE chromaticity coordinates (x = 0.65, y = 0.34).     

Luminescent properties of Sr5(PO4)3 Cl:Eu2+, Mn2+ as?a?potential phosphor for UV-LED-based white LEDs

Eu²⁺ and Mn²⁺ co-activated Sr₅(PO₄)₃Cl phosphors with blue and orange color double emission bands, under a broad-band excitation wavelength range of 340–400 nm, were synthesized by the solid-state reaction. It was found that the processing parameters, including the fluxes, annealing time and activators concentrations, affect the emission intensity and other luminescent properties. Energy transfer between Eu²⁺ and Mn²⁺ was discovered and the transfer efficiency was also estimated based on relative intensities of Eu²⁺ and Mn²⁺ emission. Thus the relative strength of blue and orange emission intensities could be tuned by varying the relative concentration of Eu²⁺ and Mn²⁺. Since the photoluminescence excitation spectra of the newly developed Sr₅(PO₄)₃Cl:Eu²⁺, Mn²⁺ phosphors exhibit a strong absorption in the range of 340–400 nm, they are promising for producing UV-LED-based white LEDs.     

Intrinsic room-temperature ferromagnetism of V-doped TiO2 (B) nanotubes synthesized by the hydrothermal method

Nanotubes of TiO₂(B) phase doped with 5 at.% of vanadium (V) have been synthesized by a hydrothermal method, followed by calcination at 300 °C in air and argon atmosphere, respectively. These nanotubes exhibit ferromagnetic character with clear hysteresis loop at room-temperature. X-ray diffraction and Fourier transform infrared spectroscopy confirm that the ferromagnetic behavior is intrinsic to the material and not due to other phases and/or metallic clusters. The photoluminescence and hysteresis loop characteristics are found to be dependent on calcination conditions, and implicate the role of oxygen vacancies. Existence of higher oxygen vacancies in V-doped TiO₂(B) nanotubes synthesized in argon than the air atmosphere is supported by the room-temperature photoluminescence spectra. The enhanced ferromagnetic behavior observed in V-doped TiO₂(B) nanotubes synthesized in argon than the air atmosphere is explained in terms of bound magnetic polaron (BMP) model.