Electrochemical hydrogenation of citral

The factors (concentration of citral, composition of the solvent, AcOH citral ratio) affecting electrochemical hydrogenation of citral at an annealed copper cathode have been determined. The highest total yield (94 %) of the alcohols (nerol, geraniol, citronellol) with a considerable predominance of the latter is achieved at 40 % DMF in water, citral concentration 0.02M, and AcOH citral ratio=101. The transition to purely organic or purely aqueous media leads to a decrease in both the total yield of the alcohols and the selectivity of the process.For Part 1, see Ref. lTranslated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 1919–1923, November, 1993.     

锡气体扩散电极上电化学还原二氧化碳制甲酸性能的稳定性

研究了Sn气体扩散电极(SGDE)上电化学还原CO₂制甲酸(ERCF)性能的稳定性。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能量色散谱(EDX)和活性表面积测试等技术手段 分别表征SGDE在电化学还原CO₂制甲酸过程前后的物相结构、表面形貌、元素组成和活性表面积。 采用生成甲酸的法拉第效率(f_HCOOH)评价SGDE上电化学还原CO₂制甲酸的性能。 结果显示,f_HCOOH随电解时间的延长急剧地降低,电解时间12 h的f_HCOOH((36.6±1.6)%)比电解时间0.5 h时的f_HCOOH((78.5±0.1)%)降低了53%。 SGDE在12 h电还原反应后,表面沉积了微量Fe,而且Sn含量(质量分数)减少了66%,活性表面积降低了41%。 进一步的研究发现,沉积的微量Fe对电化学还原CO₂制甲酸过程基本没有影响,Sn含量和活性表面积的降低可能是SGDE上电化学还原CO₂制甲酸性能降低的主要原因。     

Electrochemiluminescence in the reduction of uranyl ions on platinum in sulfuric acid solutions

Electrochemiluminescence (ECL) accompanying the reduction of uranyl ions on a platinum cathode in sulfuric solutions in the presence of XeO₃ was observed and studied. At early stages of the electrolysis (at 0.34<φ<0.62 V), the chemiluminescence reaction U^V+XeO₃ contributes mainly to the luminescence intensity, whereas at φ<0.32 V, the contribution of the reaction U^IV+XeO₃ predominates. The transfer coefficient for the primary electrochemical stage, formation of U^V, was estimated: α=0.46−0.54. The high sensitivity of ECL to the state of the electrode surface is explained by the fact that the reduction of U^VI occurs on the most active sites only. the background chemiluminescence reactions, among which U^V+O₂ and U^V+H₂O₂ can be distinguished, were considered, and their contributions to ECL were determined. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1928–1934, October, 1999.     

铜/活性炭复合材料的电化学性能研究

电极材料的开发与完善是提高电容器性能的主要途径之一.本文以烟煤为炭质原料、硝酸铜为添加剂催化制备了铜/活性炭复合材料,并对氧化铜电极、活性炭电极和铜/活性炭复合材料电极进行了循环伏安、交流阻抗和电压保持能力等电化学性能测试.结果表明,活性炭中含有适量的铜可与活性炭产生协同效应,铜/炭复合材料的电容量高于纯氧化铜电极和活性炭电极的电容量之和,含铜20%的活性炭比电容量可达67.5 F/g,是同样条件制得的无铜活性炭比电容量的1.72倍;含铜活性炭具有较好的循环性能、容量特性和较小的阻抗;但其开路电压的自保持性能有待进一步改善.     

Sn/Cu电极电化学还原CO2的研究

采用电沉积法制备Sn/Cu电极,由SEM观察并研究了电沉积电流密度对电极形貌的影响.在碱性三电极体系中考察了Sn/Cu电极对析氢、CO2还原的影响.发现10 mA.cm-2和15 mA.cm-2电沉积电流密度下制得的电极活性较高,尤以15 mA.cm-2时电极性能更佳,并指出了电还原CO2关键材料的结构特性.     

苯甲酸在疏水性复合电极上的电化学还原行为

以铜片和锌片为基材,复合电镀制得Cu-PTFE(聚四氟乙烯)和Zn-PTFE疏水性复合电极,并将复合电极应用于苯甲酸的电化学还原行为研究。测定了复合电极在电解液中的Tafel极化曲线、循环伏安、电极稳定性和交流阻抗等电化学参数。结果表明,在苯甲酸电还原制备苯甲醛中,Cu-PTFE复合电极相对于Zn-PTFE复合电极具有较高的催化活性,其电还原产率分别为88.4%和79.2%,因此,Cu-PTFE复合电极有望成为苯甲酸电化学还原制备苯甲醛的电极材料。电化学行为的研究结果显示,苯甲酸在疏水性复合电极上的电还原过程可能只受电子迁移过程控制。     

毛细管电泳-电化学检测法测定血浆中水溶性小分子抗氧化剂

应用毛细管电泳电化学检测方法,以金属铜电极为检测电极,研究了同时测定人血浆中水溶性小分子抗氧化剂谷胱甘肽(GSH)、尿酸(UA)、色氨酸(Try)和半胱氨酸(Cys)的最佳条件。在最佳实验条件下,各组分的线性范围在1.0×10-6～5.0×10-4mol/L内;检出限在10-6mol/L数量级。该法具有分析速度快、灵敏度高等优点,对血浆样品的测定取得了满意的结果。     

5-硝基-1,4-萘醌在玻碳电极上的电化学行为研究

采用循环伏安法和线性扫描伏安法,研究了5-硝基-1,4-萘醌在玻碳电极上的电化学行为.结果表明,在丙酮的稀硫酸溶液中,5-硝基-1,4-萘醌在0.0V、-0.8V(vs.SCE)处各有一个还原峰,分别为硝基、醌的不可逆电极反应;5-硝基-1,4-萘醌在电极表面的传质为线性扩散,电还原过程由扩散控制,并求得传递系数分别为...     

Effect of antimony on the reduction of anodic Pbo_2 film on Pb-Sb alloys in sulfuric acid solution

The reduction processes of anodic PbO2 films formed on Pb-Sb alloys in 4.5mol·dm-3 H2SO4 solution at 1.4 V(vs.Hg/Hg2SO4) for 1 h have been investigated by pho-tocurrent method,chronoamperometry,linear sweep voltammetry as well as X-ray diifractornetry.It was found that the reduction of most of the β-PbO2 and part of the α-PbO2 to PbSO4 can be completed within I s between 0.9 V and 1.0 V(vs.Hg/Hg2SO4) and proceeds much faster than that of the remaining a-PbO2 into photoactive α·PbOx (1相似文献   

Electrochemical behaviour of an indium electrode in concentrated KOH solutions at different temperatures

Summary The electrochemical behaviour of pure indium in KOH solutions (1–4M) was studied at different temperatures (25–70°C) by potentiostatic techniques. Two anodic peaks corresponding to the formation of In(OH)₃ and In₂O₃ were observed. The heights of the two peaks increased with the increase of alkali concentration. An increase of temperature increased the peak currents and shifted their corresponding potentials to more negative values. The variation of the peak currents and peak potentials with scan rate suggested that the anodic dissolution of indium was a diffusion controlled process. In cyclic voltammetry, the reverse scan consistently showed one peak which was attributed to the reduction of anodic oxidation products into indium. X-ray diffraction analysis confirmed the presence of In(OH)₃ at the first anodic peak, In(OH)₃ and In₂O₃ at the second anodic peak and In₂O₃ in the permanent passive region.

---

Zum elektrochemischen Verhalten einer Indium-Elektrode in konzentrierter Kalilauge bei verschiedenen Temperaturen

Zusammenfassung Es wurde das Verhalten von reinem Indium in 1 – 4M KOH-Lösungen bei Temperaturen zwischen 25 und 70°C mittels potentiostatischer Methoden untersucht. Zwei anodische Peaks, entsprechend der Bildung von In(OH)₃ und In₂O₃, traten auf. Die Höhe der beiden Peaks wurde mit zunehmender Alkalikonzentration gesteigert. Eine Temperaturerhöhung verstärkte die Peakströme und verschob die entsprechenden Potentiale zu negativeren Werten. Die Abhängigkeit der Peakströme und Peakpotentiale von der Scangeschwindigkeit legte den Schluß nahe, daß die anodische Lösung von Indium in einem diffusionskontrollierten Prozeß stattfindet. Bei der cyclischen Voltammetrie zeigte der reverse Scan einheitlich einen Peak, der der Reduktion der anodischen Oxidationsprodukte zu Indium zugeschrieben wurde. Röntgendiffraktionsanalyse bestätigte die Präsenz von In(OH)₃ beim ersten anodischen Peak, In(OH)₃ beim zweiten Peak und In₂O₃ im permanent passiven Bereich.

     

钛基二氧化铅电极电沉积制备过程中的立体生长机理

采用恒电位的方法在涂有SnO2＋Sb2O5中间层的Ti基体上电沉积制备了不同颗粒尺度的Ti/PbO2电极, 利用XPS, XRD和SEM等方法对Ti/PbO2电极电沉积制备过程中电极的结构、表面形貌等物理化学性能进行了研究. 结果表明, Ti/PbO2电极涂层中Pb元素在138.2～138.4 eV之间有明显的Pb4f7/2峰, 表明电极表面上主要得到的是PbO, XRD和XPS分析结果证明电极涂层体相生成的是PbO2. 基于Ti/PbO2涂层的形成是不同晶面生长过程的事实, 提出Ti/PbO2电极的立体生长机理.     

金-石墨烯修饰电极电化学检测塑料瓶中双酚A

在离子液体碳糊电极(CILE)表面上采用一步电还原法制备了纳米金(nAu)-石墨烯(GR)复合膜修饰电极(nAu-GR/CILE).研究了双酚A(BPA)在nAu-GR/CILE上的电化学行为,BPA的电极反应过程为受吸附控制的不可逆过程;采用示差脉冲伏安法研究了BPA氧化峰电流和浓度之间的关系,在0.08～400.0...     

巯基乙酸修饰金电极的电化学行为及对铜离子的测定

通过共价自组装的方法制备了巯基乙酸单分子层修饰金电极.在含有铜离子的磷酸缓冲液中搅拌吸附,铜离子与修饰电极表面的巯基乙酸形成的活性配合物吸附在电极表面.用该电极对不同浓度的铜离子进行检测,发现峰电流随铜离子浓度的增大而增大,在0.05~1μmol/L之间出现良好的线性关系,其最低检测限可达10 nmol/L.     

基于L-半胱氨酸/CdTe量子点修饰电极的电化学传感器的制备及其对Pb~(2+)的检测

成功制备了由L-半胱氨酸和CdTe量子点作为修饰材料的电化学传感器并用于水体中Pb~(2+)的检测。巯基丙酸修饰的CdTe量子点通过水相合成,表面含有大量羧基,与L-半胱氨酸表面的氨基形成酰胺键,修饰于金电极表面。通过荧光分光光度计、透射电子显微镜、红外光谱、X射线衍射对L-Cys/CdTe QDs复合材料进行表征。采用循环伏安法(CV)研究了L-Cys/CdTe QDs修饰成分在金电极上的电化学性能及CdTe量子点的最佳自组装时间。采用差分脉冲溶出伏安法(DPSV)研究了铅离子在修饰电极上的电化学行为。在优化实验条件下,Pb~(2+)浓度在1.0×10~(-6)~1.0×10~(-2) mol/L范围内与其峰电流呈良好的线性关系,相关系数(r2)为0.993 8,检出限(3σ,n=5)为4.0×10~(-7) mol/L。该传感器具有良好的重现性和稳定性,有望用于实际水样中铅离子的检测。     

Electrochemical behavior of mesoionic sydnone derivatives at wax-impregnated carbon paste electrode

The-N=N-moiety in the mesoionic 3-phenyl sydnone and its derivatives like tolyl sydnones and anisyl sydnones undergo two-electron irreversible electrochemical reduction in Britton-Robinson (BR) buffer at wax-impregnated carbon paste electrodes. Infrared, nuclear magnetic resonance, and mass-spectral data, used to characterize the reduced product, confirm the proposed mechanism. The pasting liquid at the surface of the electrode is found to decrease the electron-transfer rate and cause a higher overpotential compared to homogeneous electrodes. The influence of variation of pH on the peak current and peak potentials is studied in the acidic range. The cathodic peak shifts to more negative potentials with increase in pH, indicating the involvement of proton in the reduction process. This could be a new method of preparation of 2,4-dihydro-3-substituted 1,2,3-oxadiazole-5-one. The substituent effect and the effect of variation of scan rate, concentration, and temperature on peak currents and peak potentials is discussed. The cathodic shift in various organic co-solvents (methanol, acetonitrile, DMF, DMSO) using BRB as the supporting electrolyte is examined. Published in Russian in Elektrokhimiya, 2006, Vol. 42; No. 7, pp. 862–868. The text was submitted by the authors in English.     

Special Features of the Electrochemical Oxidation of Substituted 4-Carboxy-1,4-dihydropyridines

Electrochemical oxidation potentials of 1,4-dihydropyridines substituted with 4-COOH, 4-COOR, and 4-CONRR' groups have been determined in aprotic acetonitrile by the rotating ring-disk electrode method (RRDE). The electrochemical reduction potentials of the resulting products were also determined at the ring electrode. It was established that protonated pyridines are formed in the oxidation of derivatives with and without a substituent in position 4 of the heterocycle. In the case of 4-alkoxycarbonyl substituted compounds the substituent at position 4 is generally retained. 1,4-Dihydrogenated derivatives of isonicotinic acid as a rule loose the substituent at position 4 on oxidation, and both types of product were recorded for the corresponding 4-carbamoyl derivatives. The substituent at position 9 of the heterocycle was mainly retained on electrochemical oxidation of the 3,3,6,6-tetramethyl-1,8-dioxo-1,2,3,4,5,6,7,8,9,10-decahydroacridine derivatives studi! ed.     

An Efficient Simultaneous Electrochemical Detection of Nanomolar Epinephrine and Uric Acid using Low Temperature Synthesized Nano-sized Copper Telluride

Herein we developed a simple, cost effective, electrochemical sensor based on nanosized copper telluride (nps-CuTe) for simultaneous detection of epinephrine (EP) and uric acid (UA). Voltammetric responses suggests dramatical improvement of electrocatalytic properties of both molecules by incorporating CuTe nps into unmodified graphite paste electrode (bare GP). Differential pulse voltammetric (DPV) measurement depicts large potential separation of 128 mV between EP and UA, allows their simultaneous determination from binary mixture. Under optimized condition, CuTe modified graphite paste electrode (CuTe/GP) manifested linear relationships of EP and UA in the range of 5–60 μM and 5–120 μM with detection limit (S/N=3) of 18 nM and 32 nM respectively. Moreover, CuTe/GP showed satisfactory response towards pharmaceutical and clinical samples for determining EP and UA concentrations.     

Effect of solution flow rate and direction on copper electrodeposition process from sulfuric acid electrolyte on porous electrode with high electric conductivity

The effect of solution flow direction and rate on the dynamics of copper electrodeposition onto a premetallized coal-graphite VINN-250 material from a dilute copper sulfate sulfuric acid solution is experimentally studied in the direct-flow mode. A light effect of solution supply on the copper deposit final mass for high and low solution flow rates is found, while the effect of this parameter on the metal distribution within the porous electrode is significant. The most uniform copper deposit distribution throughout the porous electrode is observed in the case of intermediate solution flow rates at its rear supply. The obtained experimental data agree qualitatively with the earlier published mathematical simulation results. Small systematic deviations from numeric calculations can be due to the process disregarded in the mathematical model: the effect of gas phase formed within the porous cathode due to the simultaneous hydrogen evolution.     

Electrochemical reduction of halogenated pyrimidines at mercury cathodes in acetonitrile

Cyclic voltammetry and controlled-potential electrolysis have been employed to investigate the reduction of some mono-, di-, tri-, and tetrahalopyrimidines at mercury cathodes in acetonitrile containing tetramethylammonium tetrafluoroborate. Two irreversible cyclic voltammetric waves are observed for reduction of 2-bromo-, 5-bromo-, and 2-chloropyrimidine; the first wave is due to cleavage of the carbon---halogen bond, and the second wave is attributable to reduction of pyrimidine. Cyclic voltammograms for 2,4-dichloro- and 4,6-dichloropyrimidine exhibit three cathodic waves, whereas that for 2,4,6-trichloropyrimidine shows four cathodic waves, arising from sequential cleavage of carbon---chlorine bonds as well as the reduction of pyrimidine. For the reduction of 2,4,5,6-tetrachloropyrimidine, a cyclic voltammogram exhibits four major irreversible cathodic waves corresponding to the cleavage of carbon---chlorine bonds, but the wave for reduction of pyrimidine is poorly defined. Bulk electrolyses of halopyrimidines at potentials for different stages of reduction lead to products that are consistent with expectations based upon cyclic voltammetry. In addition, our findings agree well with theoretical calculations of the relative stabilities of the various reduction intermediates. Mechanistic aspects of the reduction of halopyrimidines are discussed and, using homogeneous redox catalysis, we have determined the lifetimes of the electrogenerated radical-anions of 2-bromo- and 2-chloropyrimidine.     

咖啡酸苯乙酯在玻碳电极上的电化学行为研究

采用循环伏安法和差分脉冲伏安法研究了咖啡酸苯乙酯(CAPE)在玻碳电极表面上的电化学行为。在0.05 mol.dm-3磷酸盐缓冲溶液(PBS,pH=7.6)中,CAPE在0.229 V和0.214 V处呈现一对明显的氧化还原峰。考察了溶液pH值和扫描速率等因素对CAPE电化学行为的影响,结果表明,电化学过程中CAPE的电子转移数为2,参与反应的质子数也为2,且为吸附控制过程。在0.05 mol.dm-3磷酸盐缓冲溶液(PBS,pH=7.6)中,CAPE的氧化峰电流与其浓度在0.34～3.40μmol.dm-3范围内成线性关系,其响应灵敏度为0.88μA/μmol.dm-3,检出限为60 nmol.dm-3(S/N=3)。本研究建立了一种简单、快速、可灵敏测定CAPE的方法。同时对CAPE在玻碳电极上的电化学行为进行了较为详细的研究。