界面缩聚法PS-PVA 双层聚合物空心微球的研制

以界面缩聚反应为基础初步总结出一条PS-PVA双层聚合物空心微球制备工艺,并就工艺中间苯二酰氯（IPC）浓度、交联反应时间、搅拌速度和固化温度等影响因素进行了初步讨论。通过该工艺成功地制得了球形度≥99%、同心度>90%及表面光洁度<10nm的PS-PVA双层空心微球。     

臭氧改性及搅拌桨结构对大直径双层球制备的影响

随着高功率激光器的飞速发展,ICF物理实验对聚苯乙烯（PS）-聚乙烯醇（PVA）双层空心微球的规格要求逐渐提高,直径要求将达到700～900 m。针对该直径范围的PS-PVA双层空心微球,通过采用PS球臭氧化表面改性技术和搅拌桨叶轮结构优化技术,对传统乳液微封装法制备双层空心微球工艺进行了改进,臭氧化表面改性后PS固体核心发生憎水-亲水转变,提高了PS与PVA之间的作用强度;搅拌桨叶轮结构优化,改善了体系容器内溶液流场均匀性,使得微球在整个体系中的运动相对平稳,从而初步制得了直径范围在700～900 m的双层空心微球。     

充气温度对PS-PVA-CH塑料微球性能的影响

 主要研究了PS-PVA-CH空心塑料微球充气时，充气平衡温度对微球强度、球形度和表面形貌的影响。对PS，PVA和CH材料的热重分析结果表明，PS和PVA具有较高的分解温度，而PS-PVA双层球和PS-PVA-CH塑料微球升温后的耐外压实验表明，温度升高后双层球耐外压强度降低很快，不能满足充Ar气需要；而3层球在100~120℃仍有很高强度，在该温度下，可以实现充Ar气。微球表面形貌分析结果显示，高温充气后，3层球表面粗糙度升高。     

充气温度对PS-PVA-CH塑料微球性能的影响

主要研究了PS-PVA-CH空心塑料微球充气时,充气平衡温度对微球强度、球形度和表面形貌的影响。对PS,PVA和CH材料的热重分析结果表明,PS和PVA具有较高的分解温度,而PS-PVA双层球和PS-PVA-CH塑料微球升温后的耐外压实验表明,温度升高后双层球耐外压强度降低很快,不能满足充Ar气需要;而3层球在100~120℃仍有很高强度,在该温度下,可以实现充Ar气。微球表面形貌分析结果显示,高温充气后,3层球表面粗糙度升高。     

PS-RF双层空心微球的制备

 采用聚苯乙烯(PS)空心微球为模板,间苯二酚-甲醛(RF)为前驱体溶液,邻苯二甲酸二丁酯为分散剂,以界面聚合反应为基础初步总结出一条PS-RF双层聚合物空心微球的制备工艺,并就制备过程中RF溶液与分散剂油相的选择、预聚时间、搅拌速率、固化温度等影响因素进行了讨论。当RF溶液质量分数为25%,间苯二酚与碳酸钠的物质的量之比为100,预聚24 h,搅拌速率120～200 r/min,固化温度35 ℃时,制得了球形度和同心度达到95%以上,表面粗糙度小于10 nm的PS-RF双层空心微球。     

PS-RF双层空心微球的制备

采用聚苯乙烯(PS)空心微球为模板,间苯二酚-甲醛(RF)为前驱体溶液,邻苯二甲酸二丁酯为分散剂,以界面聚合反应为基础初步总结出一条PS-RF双层聚合物空心微球的制备工艺,并就制备过程中RF溶液与分散剂油相的选择、预聚时间、搅拌速率、固化温度等影响因素进行了讨论。当RF溶液质量分数为25%,间苯二酚与碳酸钠的物质的量之比为100,预聚24 h,搅拌速率120～200 r/min,固化温度35 ℃时,制得了球形度和同心度达到95%以上,表面粗糙度小于10 nm的PS-RF双层空心微球。     

非离子型表面活性剂Tween 20对大尺寸双层空心微球制备的影响

为了改善臭氧处理聚苯乙烯(PS)单层球与聚乙烯醇(PVA)溶液生成的双层乳粒在油相中的分散性,提高大尺寸双层球的成活率,在双层球制备过程中采用了非离子型表面活性剂Tween 20 (T-20)来改性该种PS单层球。结果表明经表面活性剂T-20改性后显著降低了PS薄膜的亲水接触角,提高了PS与PVA间的相互作用,同时也大幅度提高了PS薄膜对PVA的吸附速率。红外光谱和紫外-可见分光光度计的测试结果证明：在PVA固化过程中,由于PVA与T-20的相比太大,PS表面吸附的表面活性剂T-20部分会被PVA置换、迁移至PVA溶液中。 T-20的迁移提高了制备双层球过程中水相与外油相的粘度比且显著降低PVA溶液表面张力,从而有利于实现双重乳粒在油相中的单分散。因此,T-20是制备大尺寸PS-PVA双层空心微球有效的表面活性剂。     

ICF氘代固体靶的研制

 以自制全氘代苯乙烯单体(氘代率99%)为原料, 以偶氮二异丁腈为引发剂, 经自由基本体聚合反应, 先制得全氘代聚苯乙烯, 最后采用乳液微封装技术制得了直径150～450μm、壁厚2～15μm、球形度≥99.5%、同心度95%～98%、表面粗糙度＜30nm的ICF固体靶用空心微球。介绍了制备工艺,并对全氘代聚笨乙烯分子量及其分布的控制,微球壁内气泡形成机理,微球储存稳定性等进行了初步探讨。     

ICF氘代固体靶的研制

以自制全氘代苯乙烯单体(氘代率99%)为原料, 以偶氮二异丁腈为引发剂, 经自由基本体聚合反应, 先制得全氘代聚苯乙烯, 最后采用乳液微封装技术制得了直径150～450μm、壁厚2～15μm、球形度≥99.5%、同心度95%～98%、表面粗糙度＜30nm的ICF固体靶用空心微球。介绍了制备工艺,并对全氘代聚笨乙烯分子量及其分布的控制,微球壁内气泡形成机理,微球储存稳定性等进行了初步探讨。     

载气组份对空心玻璃微球炉内成球过程的影响

为实现惯性约束聚变靶用空心玻璃微球的干凝胶法高效制备,从数值模拟和工艺实验两个方面研究了载气组份对干凝胶粒子炉内成球过程及最终空心玻璃微球性能的影响。结果表明：载气组份显著影响粒子/微球与载气之间的热量和质量传递过程,但载气组份对粒子/微球在炉内的下落速度影响很小;提高载气中氦气的体积分数可以显著提高干凝胶粒子在吸热阶段的升温速率,更为迅速有效地完成封装过程,这不仅使得干凝胶粒子发泡成为空心球的比例增大,而且还有利于制备得到大纵横比的空心玻璃微球;但是,在载气中保持适当体积分数的氩气,有利于提高玻璃微球的表面质量和成品率。当载气中氦气的体积分数在50%~80%时,干凝胶粒子的成球率较高,空心玻璃微球的球形度、同心度和表面粗糙度能满足制靶要求。     

Design of adaptive spatial filter at uniform standard for automatic analysis of digital holographic microscopy

The spatial filtering method is a useful technique for the dynamic and automatic analysis in digital holographic microscopy. It has been shown that the proper selection of the spatial filter would improve the quality of the reconstructed image. However different results would be obtained by employing the spatial filter with different parameter threshold decided at different standard. This paper, according to the histogram analysis of the distribution of the +1 term spectrum of each hologram, gropes for the uniform standard for the decision of the threshold of the adaptive filter. It helps the adaptive spatial filtering method to be more advantageous for the dynamic and automatic analysis.     

High-resolution recordings of thePR segment in magnetocardiography

Summary ThePR interval of magnetocardiograms has been measured with a SQUID sensor in the Berlin magnetically shielded room. In addition to previously reported ramps with isolated superimposed signals in several cases a structured morphology has been found. Paper presented at the ?IV International Workshop on Biomagnetism?, held in Rome, September 14–16, 1982.     

Solvatochromism of Ternary Iron (II) Diimine Cyanide Complexes in 2-Ethyl-2-(hydroxymethyl) 1,3-Propanediol (Trimethylol Propane)

The solvatochromic behaviour of bis-(2,2′-bipyridyl)-biscyanoiron (II) and 2,2′- bipyridyltetracyanoiron (II) in 2-ethyl-2-(hydroxymethyl)-1,3-propanediol has been established. The significance and sensitivities of the solvatochromic shifts of these charge-transfer bands are outlined for the two iron complexes above.     

Adaptive noise cancellation in neuromagnetic measurement systems

Summary The noise spectrum of a superconducting second-derivative gradiometer has been investigated in an urban environment. Data have been acquired from the gradiometer with three orthogonal accelerometers and a triaxial fluxgate magnetometer attached to the dewar. These data have been analyzed by using signal processing techniques, primarily an adaptive noise canceller, to reduce noise in the gradiometer data. Results shown here indicate that the environmental noise and/or the dewar motion noise can be reduced as much as 40 dB in noise power. It is also shown, in the case of poor signal-to-noise ratio (S/N∼1), that a 10 Hz sine wave can be extracted. This technique not only shows promise for noise reduction, but also aids in the identification of noise signals which might be misconstrued as part of the evoked response. Analysis of data containing evoked response is now underway. Paper presented at the ?IV International Workshop on Biomagnetism?, held in Rome, September 14–16, 1982.     

光折变晶体钛酸秘的折射率和光学均匀性的测量

本文报导光折变晶体钛酸铋的折射率和光学均匀性的测量结果。     

Correspondence of Fluorescing States of Naphthols and Naphtholate Anions and its Effect on the Calculation of pKa∗ from Spectral Shifts

The validity of dissociation constants of electronically excited acids and bases, calculated from spectral shifts^1,2 accompanying protolytic dissociation, especially where shifts of fluorescence spectra are employed, is dependent, among other factors, upon fluorescence orginating from excited states of the same electronic configuration in both acid and conjugate base.³ In some of the molecules whose excited state acid-base properties have been most extensively studied, notably some derivatives of naphthalene, energy level reversals have been shown to accompany dissociation in the lowest excited singlet state in aqueous solutions.⁴ The spectroscopic properties and excited state dissociation phenomena of the naphthols have been studied extensively from several points of view.^5-9 While the calculation of the excited state dissociation properties of β-naphthol, in which fluorescence occurs from the ¹L_b state in both anion and neutral molecule, presents no particular problem with regard to correspondence of the lowest excited singlet states of conjugate acid and base, it appeared that in α-naphthol, by analogy with α-naphthylamine⁴, fluoescence might occur from the ¹L_a state in the conjugate base and from the ¹L_b state in the conjugate acid. Thus it seemed that a careful consideration of the states from which the fluorescences of the conjugate species derived from α-naphthol in fluid aqueous solutions orginated, would be useful.     

CoSi2/Si (111) Interface study by X-ray standing waves

Summary The CoSi₂/Si (111) interface has been studied with the X-ray standing-wave technique. The interface (a 49? thick CoSi₂ layer) has been epitaxially grown on Si (111) under ultrahigh vacuum andin situ characterized with Auger spectroscopy and low-energy electron diffraction. The perpendicular lattice mismatch between epilayer and substrate has been measured with double-crystal X-ray diffraction. The X-ray standing-wave analysis gives clear indication that the Co atoms are fivefold coordinated at the interface. This work has been partially supported by Progetto Finalizzato ?Materiali e dispositivi per l'Elettronica a Stato Solido?.     

Luminescence behavior of tetraaza macrocylic nickel (II) complexes and non-linear Stern-Volmer quenching

Macrocylic dicarbinolamine nickel (II) complexes with diimine moiety in their ligand exhibited luminescence, when irradiated at their charge transfer band. The Stern-Volmer (S-V) plots of one of the complexes in DMF medium exhibited positive curvature, when FeC1₃ was used as a quencher, while the same complex showed negative curvature when nitrobenzene was used as a quencher. The mechanism for the luminescence quenching of the macrocyclic complex has also been discussed.     

Imprinting the nanostructures on the high refractive index semiconductor glass

The centimeter range one- and two-dimensional nanostructures of 70 nm pitch have been imprinted by hot pressing with a quartz, silicon or nickel mold, at 240 °C, onto the surface of Ge₂₀As₂₀Se₁₄Te₄₆ semiconductor glass. Excellent glass stability of this glass allows multiple re-pressing of the nano-structures. With increasing the Te/Se ratio in the glass formula, the refractive index reaches a value of 3.5 with an option of free electron absorption at elevated temperatures pointing out the use of such nanostructures in submicron and micron scale electronic devices/chips, moth eye structures and photonic crystals.