首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 56 毫秒
1.
刘瑞  徐征  赵谡玲  张福俊  曹晓宁  孔超  曹文喆  龚伟 《物理学报》2011,60(5):58801-058801
制备了结构为ITO/Pentacene/C60/Al的双层光伏电池器件,在C60/Al界面插入了常用的缓冲层材料bathocuproine(BCP)作为阴极缓冲层,通过优化BCP层的厚度来提高电池的性能并研究了阴极缓冲层的作用机理.实验发现,BCP厚度为10 nm时器件的效率最高,为0.46%.在此基础上,利用bathophenanthroline(Bphen)和3,4,9,10-Perylenetetracarb-oxylicdianhydride(PTCDA 关键词: 有机太阳能电池 Pentacene 60')" href="#">C60 缓冲层  相似文献   

2.
ZnS作为空穴缓冲层的新型有机发光二极管   总被引:3,自引:3,他引:0       下载免费PDF全文
仲飞  叶勤  刘彭义  翟琳  吴敬  张靖垒 《发光学报》2006,27(6):877-881
采用磁控溅射方法在ITO表面沉积了不同厚度的ZnS超薄膜作为有机发光二极管(OLEDs)的缓冲层,使典型结构(ITO/TPD/Alq3/Al)的OLEDs的发光性能得到改善。ZnS缓冲层厚度对器件性能影响的实验结果表明,当ZnS缓冲层厚度为5nm时,器件电流密度提高了近2倍,亮度提高了2倍;当ZnS缓冲层厚度为10nm时,器件发光的电流效率提高18%,器件的性能得到改善。宽禁带的ZnS缓冲层对空穴从阳极到有机功能层的注入有阻碍作用,促进器件载流子平衡,提高了器件发光效率,改善了器件性能。  相似文献   

3.
制备了ITO/NPB/LiF/Alq3/LiF/Al的器件,测量了该组器件效率和亮度的磁效应.结果表明,在50 mT磁场中,当LiF缓冲层厚度为0.8 nm时,器件的效率最大增加了12.4%,磁致亮度最大变化率17%.同时,制备的磷光器件ITO/NPB/LiF/CBP:6 wt% Ir(ppy)3/BCP/Alq3/ LiF/Al,在50mT磁场作用下,当LiF缓冲层的厚度为0.8 nm时,器件的效率最大增加12.1%.在Alq3 关键词: 有机发光 磁场 效率 磁致亮度  相似文献   

4.
聚合物级联发光器件   总被引:1,自引:0,他引:1  
基于溶液加工方法制备了聚乙撑二氧噻吩-聚(苯乙烯磺酸盐)(PEDOT∶PSS)/氧化锌(ZnO)/乙氧基化聚乙烯亚胺(PEIE)电荷产生层的聚合物级联发光器件, 发现PEDOT∶PSS层电导和厚度对器件的电流-电压特性影响较小, 不同PEDOT∶PSS对器件发光效率的影响主要来自于其对发光层激子不同的猝灭作用, PEDOT∶PSS厚度为60 nm的级联器件比PEDOT∶PSS 厚度为30 nm的级联器件的发光效率稍高, 原因是PEDOT∶PSS较厚时, 其表面形貌更均匀。级联器件的发光效率和驱动电压分别与发光子单元的发光效率和驱动电压之和相近, 说明在较低的电压下电荷产生层就能够有效产生电荷并注入到发光子单元中,级联器件的发光光谱中包含两个发光子单元的发光光谱,说明两个发光子单元在级联器件中都能正常工作。通过对电荷产生层的电容-电压(C-V)特性的测试, 确认了在电荷产生层中存在电荷的积累过程。证明了PEDOT∶PSS/ZnO/PEIE为有效的电荷产生层。首次报道了包含三个SY-PPV发光单元的级联器件, 三个发光子单元发光效率之和与级联器件的发光效率相当, 其最大发光效率和最大外量子效率分别为21.7 cd·A-1和6.95%。在器件亮度为5 000 cd·m-2时, 器件的发光效率和外量子效率分别为20.5 cd·A-1和6.6%。说明并没有由于发光子单元数目增加而影响级联器件的发光效率。并且其发光光谱和发光子单元的发光光谱相接近。通过 进一步降低CGL中空穴注入层对级联器件的影响有望提高级联器件的发光效率。  相似文献   

5.
蓝色发光材料DPVBi掺杂DCJTB发光性质的研究   总被引:1,自引:1,他引:0  
对蓝光材料DPVBi掺杂红光染料DCJTB的发光性质进行了研究。首先研究了DPVBi掺杂不同质量浓度DCJTB的光致发光,当掺杂质量浓度为0.1%时,光致发光得到白光(色度x=0.36,y=0.34)。基于光致发光的实验结果,以DPVBi掺杂不同质量浓度DCJTB作发光层,制备了结构为ITO/CuPc/NPB/DPVBi:DCJTB/Alq3/LiF/Al的器件,当掺杂质量浓度为0.08%时器件实现了白色发光(色度为x=0.25,y=0.32)。研究了该白光器件的电致发光性质,白光器件在14V时达到最高亮度7822cd/m^2。在20mA/cm^2电流密度驱动下的亮度为489cd/m^2,最大流明效率为1.75lm/W。  相似文献   

6.
MoO3为缓冲层的高效非掺杂蓝色有机发光二极管   总被引:1,自引:0,他引:1       下载免费PDF全文
以典型蓝色发光材料-联苯乙烯衍生物(4,4’-bis(2,2’-diphenylvinyl) -1,1’-biphenyl,DPVBi)为发光层,采用MoO3为阳极缓冲层制备了结构简单的非掺杂型蓝色有机电致发光器件.在电流密度为20 mA/cm2、MoO3缓冲层厚度为0.5 nm对器件效率约为无缓冲层器件效率的18倍,...  相似文献   

7.
缓冲夹层影响异质结有机光伏器件性能研究   总被引:1,自引:1,他引:0  
李卫民  郭金川  周彬 《光子学报》2012,41(8):972-976
制备了结构为CuPc/缓冲层/C60异质结的有机光伏器件,分别选用三氧化钼和红荧烯为缓冲层,研究了增加缓冲层对器件性能的影响.结果表明,增加三氧化钼和红荧烯缓冲层后器件的开路电压和光电转换效率都得到提高,器件的短路电流密度和填充因子都有所降低.开路电压从没有缓冲层时的0.39V分别提高到0.58V、0.55V,转换效率从0.36%提高到0.44%,短路电流从1.92mA/cm2分别降低到1.77mA/cm2、1.81mA/cm2,填充因子从0.48分别减少到0.43、0.44.进一步研究表明器件的短路电流密度受缓冲层厚度的影响很大,当缓冲层厚度很小时,器件短路电流密度还有所增加,但随着缓冲层厚度的增加,短路电流密度逐渐减小,当缓冲层厚度为10nm时,器件短路电流密度减少到0.35mA/cm2.开路电压随着厚度的增加逐渐增加,从1nm时的0.43V增加10nm时0.63V.根据整数电荷转移模型和界面能级理论解释有机光伏器件开路电压提高以及短路电流密度减少的原因,为有机太阳能电池性能的改善提供了研究方法.  相似文献   

8.
利用有机层间互相掺杂提高有机电致发光器件的效率   总被引:3,自引:3,他引:0  
提高器件的发光效率是实现有机电致发光器件实用化的一个关键因素。通过对器件结构和制作工艺的优化设计,将有机电致发光器件的各个功能层进行互相掺杂,在层间形成互掺过渡层达到平衡载流子的注入,使得注入的电子和空穴有效地限制在互掺的有源区内,增加了载流子相遇复合的几率,进而提高器件的发光效率。器件的最大电流效率在外加电压10.5V时达到7.9cd/A,最大发光亮度在35V时达到49000cd/m^2。和一般掺杂器件相比效率提高2倍以上。同时有机层间的互相掺杂也在一定程度上消除了层问的界面,减少了有机层问的缺陷,与没有过渡层的器件相比,器件老化性能有了明显改善。  相似文献   

9.
针对有机发光器件需要提高发光效率问题,利用其最高被占用分子轨道(HOMO)有利于改善空穴注入的特点,将氧化钼(MoO3)插入m-MTDATA与NPB之间;将羟基喹啉锂(Liq)掺入4,7-联苯-1,10-邻二氮杂菲(Bphen)作n型电子传输层,制备具有空穴缓冲层和n型掺杂电子传输层的有机电致发光器件。通过单载流子电子器件J-V曲线的比较,将掺杂质量分数确定为w(Bphen)∶w(Liq)=65∶35。在完整器件中,随着MoO3厚度的增加,器件效率改善显著,当MoO3厚度达到1nm时,器件性能最佳,此后趋于饱和,对厚度变化不敏感。说明使用MoO3及n型掺杂后空穴及电子的注入传输均获得明显提高,并在发光区域达到有效平衡,器件的亮度及发光效率获得明显改善,与控制器件相比,电流效率、功率效率及亮度分别提高约62%、约98%和约60%,电压V下降了约28%。  相似文献   

10.
效率增强的新型蓝色有机发光器件   总被引:7,自引:4,他引:3  
使用一种新型空穴传输材料J003制备了不同结构、不同发光层厚度的两组蓝色发光器件,其结构为:ITO/CuPc/J003/JBEM:perylene/Alq3/LiF/Al和ITO/CuPc/J003/JBEM:perylene/TPBi/Alq3/LiF/Al,这里CuPc(Copper phthalocyanine)和LiF分别为空穴注入层(HIL)和电子注入层(EIL),J003为空穴传输层(HTL),JBEM(9,10-bis(3,5'-diaryl)phenylylanthracene)为发光层(EML),TPBj(1,3,5-tri(phenyl-2-benzimidazole)-benzene)为空穴阻挡层(HBL),Alq3(tris(8-quinolinolato)aluminium complex)为电子传输层(ETL).两种结构中前者为无阻挡层的普通型结构,后者在发光层和电子传输层中加入了空穴阻挡层,是新型阻挡层结构.研究了空穴阻挡层的引入在不同厚度发光层时对器件发光性能的影响,结果表明,新型阻挡层结构能明显提高器件的亮度和效率,但依赖于发光层厚度,利用能级图分析了其中的原因.  相似文献   

11.
Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.  相似文献   

12.
A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.  相似文献   

13.
Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·104 Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.  相似文献   

14.
The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.  相似文献   

15.
16.
We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.  相似文献   

17.
Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.  相似文献   

18.
A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.  相似文献   

19.
Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.  相似文献   

20.
Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号